GE PDW8200J10BB, PDW8200J10CC, PDW8200J10WW, PDW8211J10BB, PDW8211J10WW Installation Guide

...

Installation

Built-In Dishwasher

Instructions

I ffyou have questions,call 800-GECARESor visit our website at: www.GEAppliances.com I

BEFORE YOU BEGIN

Read these instructions completely and

carefully.

IMPORTANT- Observe all

governing codes and ordinances.

• Note to Installer - Be sure to leave these instructions for the consumer's and local inspector's use,

• Note to Consumer - Keep these instructions with your Owner's Manual for future reference.

• Skill Level - Installation of this dishwasher requires basic mechanical and electrical skills. Proper instal-

lation is the responsibility ofthe installer. Product failure due to improper installation is not covered under the GEAppliance Warranty.

•Completion Time - 1to 3 Hours. New installations require more time than replacement installations.

IMPORTANT- The dishwasher

MUST be installed to allow for future removal from the

enclosure if service is required,

If you received a damaged dishwasher, you should immediately contact your dealer or builder.

Optional Accessories - See the Owner's Manual for available custom panel kits.

FOR YOUR SAFETY

Read and observe all CAUTIONS and WARNINGS shown throughout these instructions. While performing

installations described in this booklet, gloves, safety

glasses or goggles should be worn.

READ CAREFULLY. KEEP THESE INSTRUCTIONS.

PDW8100 Series PDW8200 Series

PDW8500 Series PDW8600 Series

PDW8700 Series

*For PDW9700 Series also refer to the Instructions

provided on the template packed with that model,

PDW8800 Series PDW9200 Series PDW9700 Series* PDW9800 Series

IPub,No,31-30561-1

Dwg,No.206C1559P101j

(ND 756) 6/03 Rev

]

Installation Preparation

PARTS SUPPLIED:

[] Two #8 Phillipsflat headwood screws, 5/8"long to

secure dishwasher to underside ofcountertop or

sides of cabinetry. (Tapedtotop or side of dishwasher.) [] Side and top trim pieces [] TrimPanel Accessory Kit (notshown).

Model PDW9700only [] Drain Hoseand Hose Clamp

MATERIALS YOU WILL NEED :

[] Ferrule,compression nut and 90° Elbow (3/8"NPTexternal

thread on one end,opposite end sized to fit water supply)

[] Threadseal tape [] ULListedwire nuts (3)

Materials For New Installations Only:

[] Air gap for drain hose, if required [] Wastetee for house plumbing, if applicable [] Electrical cable or power cord, if applicable [] Screw typehose clamps

[] Strain relief for electrical connection. [] Handshut-off valve

[] Water line3/8"min.copper [] Couplerfor extending drain line, if applicable

Waste Tee

2 Wood Screws

DrainHose

Hand

90° Elbow, Ferrule and

Compression Nut

Air Gap Hose Clamps

Shut-Off Valve

Electrical Cable (or Power Cord, if applicable)

Screw Type Strain Relief

(somemodels)

_ Hose Clamp

Wire Nuts (3)

Thread SealTape

HotWater line

Coupler

TOOLS YOU WILL NEED:

[] Phillips headscrewdriver [] 5/16"and 1/4"nutdriver

[] 6"Adjustable wrench [] Level

[] Carpenters square []

Measuring tape [] Safety glasses 15/16"Socket

[] Flashlight [] Bucket to catch water when flushing the line [_ -- / ())

[] 15/16"socket (optionalfor skid removal) [] Gloves

For New Installations Only:

[] Tubingcutter [] Drill andappropriate bits

[] Holesaw set

Screwdriver

Flashlight

Gloves

Bucket

1/4__ Level

and 5/16" _ L-

Nutdriver

6"Adjustable

nch

Safety Glasses

Hole Saw Set

Carpenters Square

TubingCutter

Measuring Tape

Installation Preparation

PREPARE DISHWASHER ENCLOSURE

•The dishwasher must be installed so that drain hose is no more than 10feet in length for proper drainage.

WARNING

34-I/2"+I/4"

Undemideof

Counter_op

to Floor

Square

and

Plumb

FloorMUST

FigureA

beEvenwith PlumbingandElectric Se_ice

RoomFloor MustEnterShadedArea

•The rough cabinet opening must be at least 24"deep, 24"wide and approximately 34-1/2" high from floor to underside of the countertop.

DRAIN REQUIREMENTS

• Follow local codes and ordinances.

• Do not exceed 10feet distance to drain.

• Do not connect drain lines from other devices to the dishwasher drain hose.

NOTE:This dishwasher is equipped with a high drain loop. There isno minimum height required for drain hose routing. However, 18" minimum from floor to center of

waste tee or disposer inlet is required. See Figure D.

DETERMINE DRAIN METHOD

The type of drain installation depends on the following question.

[] Do local codes or ordinances require an air gap? [] Is waste tee less than 18" above floor?

If the answer to either question is YES, Method 1MUST

be used.

• If the answers are NO, either method may be used.

To reduce the risk of electric shock, fire, or injury to persons, the installer must ensure that the dishwasher

is completely enclosed at the time of installation.

CLEARANCES:When /L Countertop

installed into a corner,

allow 2" rain. clearance

between dishwasher and

adjacent cabinet, wall or

other appliances, Allow

28-3/8"min.clearance from the front of the dishwasher for door

opening. Figure B

Dishwasher

28-3/8"

Opening2"Minimum

Figure B

FigureC

Method 1 - Air Gap with Waste Tee or Disposer

An air gap mustbe usedwhen required bylocal codes and ordinances. The air gap mustbe installed according to manufacturers instructions.

=_== =._==_

CABINET PREPARATION

• Drill a 1-1/2" dia. hole in the cabinet wall within the shaded areas shown in Figure A for the drain hose

connection. The hole should be smooth with no sharp edges.

IMPORTANT: When connecting

drain line to disposer, check to be

sure that drain plug has been removed, DISHWASHER WILL NOT

DRAIN IF PLUG IS LEFT IN PLACE.

Figure D

Method 2 - Built-in "High Drain Loop" with Waste Tee or Disposer

Installation Preparation

PREPARE ELECTRICAL WIRING

FORPERSONAL SAFETY:Remove house fuse or open circuit breaker

before beginning installation. Do not

WARNING

use an extension cord or adapter plug with this appliance.

Electrical Requirements

• This appliance must be supplied with 120V,60 Hz. and

connected to an individual properly grounded branch circuit, protected by a 15or 20 ampere circuit breaker or time delay fuse.

•Wiring must be 2 wire with ground and rated for 75°C (176°F).

• If the electrical supply does not meet the above requirements, call a licensed electrician before proceeding.

Grounding Instructions-Cable Direct

This appliance must be connected to a grounded metal,

permanent wiring system, or an equipment grounding

conductor must be run with the circuit conductors and

be connected to the equipment grounding terminal or lead on the appliance.

Grounding Instructions-Power Cord Models

This appliance must be grounded. In the event of a

malfunction or breakdown, grounding will reduce the

risk of electric shock by providing a path of least resis- tance for electric current. This appliance is equipped with a cord having an equipment grounding conductor and a grounding plug. The plug must be plugged into an appropriate outlet that is installed and grounded in

accordance with all local codes and ordinances.

The improper connection of the equipment grounding conductor can

result in a risk of electric shock. Check

WARNING

with a qualified electrician or service representative if you are in doubt that the appliance is properly grounded.

1/ I

, Receptacle ' "

, f- Alternate q'\

, Location _ \

lq/2" Dia.

I \

from

Cabinet

Location

Area

Figure E Black'white

For models equipped with power cord: Do not modify the

plug provided with the appliance; if it will not fit the outlet, have a proper outlet installed by a qualified technician.

Cabinet Preparation & Wire Routing

•The wiring may enter the opening from either side, rear or the floor within the shaded area.

•Cut a 1-1/2" max. dia. hole to admit the electrical cable. Cable direct connections may pass through the same

hole as the drain hose and hot water line, if convenient.

If cabinet wall is metal, the hole edge must be covered with a bushing. NOTE: Power cords with plug must pass through a separate hole.

Electrical Connection to Dishwasher

Electrical connection is on the right front of dishwasher.

• For cable direct connections the cable must be routed as shown in Figure E Cable must extend a minimum of

24"from the rear wall.

• For power cord connections, install a 3-prong grounding type receptacle in the sink cabinet rear wall, 6" rain. or

18"max. from the opening, 6"to 18" above the floor.

+ 8 hidden pages