GE PDW8480N20SS, PDW8612N20SS, PDW8680N00SS, PDW8680N20SS, PDW8980N20SS Installation Guide

Appliances

Installation Instructions

Built-In Dishwasher

If you have questions, call 800.GE.CARES{800.432.2737} or visit our website at: www.ge.com

BEFORE YOU BEGIN

Read these instructions completely and

carefully.

IMPORTANT- Observe all governing codes and

ordinances.

• Note to Installer - Be sure to leave these instructions for the
consumer's and local inspector's use.

• Note to Consumer - Keep these instructions with your
Owner's Manual for future reference.

• Skill Level - Installation of this dishwasher requires
basic mechanical, electrical and plumbing skills. Proper

installation is the responsibility of the installer. Product

failure due to improper installation is not covered under
the GE Appliance Warranty. See warranty information.

• Completion Time - 1 to 3 Hours. New installations require
more time than replacement installations.

READ CAREFULLY.
KEEP THESE INSTRUCTIONS.

PDW8200 Series
PDW8400 Series
PDW8700 Series
PDW8800 Series
PDW8900 Series

IM PO RTANT-The dishwasherMUST

beinstalledtoallowforfutureremovalfromtheenclosure

if service is required.

Ifyou receiveda damaged dishwasher,you should

immediatelycontactyourdealerorbuilder.

Optional Accessories - Seethe Owner's Manual for available
custom panel kits.

FOR YOUR SAFETY

Read and observe all CAUTIONS and WARNINGS

shown throughout these instructions. While performing
installations described in this booklet, gloves and either

safety glasses or goggles should be worn.

PDW9200 Series
PDW9700 Series*
PDW9800 Series
PDW9900 Series

(__) imag

*For PDW9700 Seriesalso refer to the Instructions

provided on the template packed with that model.
(WD35X1005)

ination at work

Installation Preparation

PARTS SUPPLIED:

[] Two #8-18 x 5/8" Phillips special head screws, to

secure dishwasher to underside of countertop or

sides of cabinets. (Screwslocated in user bag.)
[] Sideand top trim pieces
[] Trim Panel Accessory Kit (not shown).

Model PDW9700 only

[] Drain Hose,Drain Hose Hanger and Hose Clamp

MATERIALS YOU WILL NEED:

[] Ferrule, compression nut and 90° Elbow (3/8" NPT

external thread on one end, opposite end sizedto

fit water supply)
[] Thread seal tape

[] UL Listed wire nuts (3)

[] Air gap for drain hose, if required

Materials For New Installations Onlg: _

[] Waste tee for house plumbing, if applicable
[] Electrical cable or power cord, if applicable wasteTee

#B Phillips
Special Head Screws

5/8" long

Drain Hose

90° Elbow,
Ferrule and

Compression Nut

Trim Pieces

Hose Clamp

Hand Thread

Shut-Off Seal Tape
Valve

Electrical Cable

(or Power Cord, if applicable)

Drain Hose Hanger

Wire Nuts (3)

Hot Water Line

[] Screw type hose clamps J_
[] Strain relief for electrical connection

[] Hand shut-off valve
[] Water line 3/8" min. copper Air

[] Coupler for extending drain line, if applicable Gap

TOOLS YOU WILL NEED:

[] Phillips head screwdriver
[] Z/4" and 5/16" nutdriver

[] 6" Adjustable wrench
[] Level

[] Carpenters square
[] Measuring tape
[] Safety glasses
[] Flashlight
[] Bucket to catch water when flushing the line
[] 15/16" socket (optional for skid removal)

[] Gloves

Phillips
Head

Screwdriver

114"and
5116"Socket

Flashlight SafetyGlasses

For New Installations Only:

[] Tubing cutter
[] Drill and appropriate bits

[] Hole saw set

Screw Tape
Hose Clamps

5/16" Nutdriver

6" Adjustable

Wrench

O

Strain Relief

Level

Tubing Cutter

Coupler

J

Carpenters
Square

Measuring Tape

Gloves

Bucket Hole Saw Set Drill and Bits

Installation Preparation

PREPARE DISHWASHER ENCLOSURE

)es or wires

]4-i/2" _+1/4"

Underside of

Countertop

to Floor

Square

and

Plumb

Floor MUST

be Evenwith

Room Floor

• The rough cabinet opening must beat least 24" deep, 24"
wide and approximatelg 34-1/2" high from floor to underside

of the countertop,

Plumbing and Electric Service

Must Enter Shaded Area

• The dishwasher must be installed sothat drain hose is no
more than 10' in length for proper drainage.

WARNING

To reduce the risk of electric shock, fire, or injurg to persons, the

installer must ensure that the dishwasher is completely enclosed
at the time of installation.

CLEARANCES: When
installed into a corner,

allow 2" min. clearance
between dishwasher and

adjacent cabinet, wall or
other appliances. Allow

28-3/8" min. clearance
from the front of the

dishwasher for door
opening. Figure B

Figure B

Countertop

28-]/8"

Clearance for Door
Opening 2" Minimum

DRAIN REQUIREMENTS

• Followlocolcodesond ordinonces.

• Do not exceed 10' distonce to droin,

• Do not connect droin linesfrom other devices to the
dishwosher droin hose.

NOTE: Air gop must be used ifwoste tee or disposer connection
islessthon 18" obove floor to prevent siphoning.

DETERMINE DRAIN METHOD

The tgpe of drain installation depends on the following

questions,

[] Do local codes or ordinances require on air gap?

[] Is woste tee less than 18" obove floor?

If the answer to either question is YES, Method i MUST
be used.

• If the answers ore NO, either method mog be used.

CABINET PREPARATION

• Drill o i-1/2" diameter hole in the cabinet wall within

the shaded areas shown in Figure Afor the drGin hose

connection. The hole should be smooth with no sharp edges.

IMPORTANT:When connecting
drain line to disposer, check to be _ 41--Remove

removed. DISHWASHERWILL NOT Plug

sure thGt drGinplug has been [_= Hopper
DRAINIF PLUGISLEFTIN PLACE.

Figure C

Method 1 - Air Gap with Waste Tee or Disposer
An air gap must be used when required bg local codes and ordinances.

The air gap must be installed according to manufacturer's instructions.

18"

Figure D

Method 2 - Drain Hose Routing
When not using an air gap, the drain hose must be routed to form a high

loop of at least 32" to prevent siphoning. See Step 15 on page 10.

Installation Preparation

PREPARE ELECTRICAL WIRING

FORPERSONALSAFETY:
Remove house fuse or open circuit breaker

before beginning installation. Do not use
an extension cord or adapter plug with this
appliance.

I

_ ,f Alternate -_,

, , Receptacle _ ",

, Location

1-1/2" Dia.

Hole (Hax.)

Electrical Requirements

• This appliance must be supplied with 120V, 60Hz.,and
connected to an individual properl9 grounded branch circuit
protected by a 15or 20 ampere circuit breaker or time delag

fuse.

• Wiring must be 2 wire with ground and rated for 75°C(176°F).

• If the electrical supply does not meet the above
requirements, call alicensed electrician before proceeding.

Grounding Instructions-Cable Direct

This appliance must be connected to a grounded metal,

permanent wiring system, or an equipment grounding
conductor must be run with the circuit conductors and be

connected to the equipment grounding terminal or lead on the
appliance.

Grounding Instructions-Power Cord Models

This appliance must be grounded. In the event of a malfunction

or breakdown, grounding will reduce the risk of electric shock
by providing a path of least resistance for electric current.

This appliance is equipped with a cord having an equipment

grounding conductor and a grounding plug. The plug must
be plugged into an appropriate outlet that is installed and
grounded in accordance with all local codes and ordinances.

The improper connection of the equipment

grounding conductor can result in a risk
of electric shock. Check with a qualified
electrician or service representative if you
are in doubt that the appliance is properly
grounded.

3" from

Cabinet

Location

Area

Figure E White

For models equipped with power cord: Do not modify the plug
provided with the appliance; if it will not fit the outlet, have a
proper outlet installed bg a qualified technician.

Cabinet Preparation and Wire Routing

• The wiring mag enter the opening from either side, rear or the
floor within the shaded area.

• Cut a 1-1/2" max. diameter hole to admit the electrical cable.
Cable direct connections mag pass through the same hole

as the drain hose and hot water line, if convenient. If cabinet
wall is metal, the hole edge must be covered with a bushing.

Note: Power cords with plug must pass through a separate
hole.

Electrical Connection to Dishwasher
Electrical connection is on the right front of dishwasher.

• Forcable direct connections the cable must be routed as
shown in Figure E.Cable must extend a minimum of 24"from

the rear wall.

• Forpower cord connections, install a B-prong grounding type

receptacle in the sink cabinet rear wall, 6" min. or 18" max.

from the opening, 6" to 18" above the flooE

Installation Instructions

PREPARE HOT WATER LINE

• The line may enter from either side, rear or floor within the
shaded area shown in Figure F.

• The line may pass through the same hole as the electrical
cable and drain hose. Or,cut an additional 1-1/2" diameter
hole to accommodate the water line. Ifpower cord with plug
isused, water line must not pass through power cord hole.

/ I

/ I

I

\

I \
I \

I \

(I 1-1/_" Dia.

Shut-off Hole

Valve

Ii

14

Hot ...... _

U .... "

From

Cabinet

Cabinet Face

Figure F

2" From Floor

Water Line Connection

• Turn off the water supply.

• Install a hand shut-off valve in an accessible location, such
as under the sink. (Optional, but strongly recommended and
may be required by local codes.)

• Water connection is on the left side of the dishwasher. Install

the hot water inlet line, using no lessthan 3/8" copper tubing.

Route the line as shown in Figure Fand extend forward at
least 19" from rear wall.

• Adjust water heater to deliver water at 120°F to 150°F at the
dishwasher.

• Flush water lineto clean out debris.

• The hot water supply line pressure must be 20-120 PSI.

STEP i INSTALL TRIM PIECES

• Locate trim strips inside dishwasher.

• Presstrim onto the tub flange on each side. Start with the top
edge, pressing on as you move towards the bottom.

• Pressthe two top trim pieces on each side of the latch.

• Open and close the door to check that trim does not bind and
does not interfere with door latch.

Trim Strip

Trim -
Strip

Figure G

STEP 2 CHECK DOOR BALANCE

• With dishwasher on the wood skid, check the door balance

by opening and closing the door.

• If the door drops when released, increase the spring tension.

If the door rises when released, decrease the tension.

• Position the spring for increased or decreased tension as

required.

• Model families have different spring mounting holes and
tension adjustment methods. Referto the appropriate figure
for your model.

PDW8200-PDW8900 Series

INCREASE

CAUTION:

Do not remove wood base until you are ready to install
the dishwasher. The dishwasher will tip over when the
door is opened if the wood base is removed.

BEFORE YOU BEGIN

Locate the 2 Phillips special head countertop
bracket screws in the user bag. Set them aside

for use in Step 13. Remove drain hose from

upper rack, if it has not been pre-installed, and

set aside for usein Step 9.

I)

DECREASE

Figure H