GE PDW8000G01BB, PDW8000G01CC, PDW8000G01WW, PDW8000G03BB, PDW8000G03CC Installation Guide
...
Installation
Instructions
Built-In Dishwashers
PDW8000,PDW8060
DesignGuidewith
Installation Instructions
GEAppliances
Safety Information
BEFORE YOU BEGIN
Read these instructions completely mid carefully.
•IMPORTANT S_,,'etheseinstructionsfor
local inspector's use. Observe all governing
codes and ordinances,
• Note to Installer - Be sure to leave these instruc-
tions with the Consmner.
• Note to Consumer - Keep these instructions with
your Owner's Mai_ual tot fllture reterence.
• Skill Level - Installation of this dishwasher requires
basic mechanical and electrical skills, Proper installa-
tion is the responsibility of the installer, Product
failure due to improper installation is not covered
under the GE Applimace Warranty.
• Completion Time - 1 to 2 Hours. Nex_ installa-
tions require more time than replacement installa-
tions.
•IMPORTANT - ThedishwasherMUST
be installed to allow for future removal fl'om the
enclosure if serxice is required,
If you receixed a damaged dislmasher, you should
immediatelv contact wmr dealer or builder.
READ CAREFULLY.
KEEP THESE INSTRUCTIONS.
FOR YOUR SAFETY
Read and observe all CAUTION and WARNINGS
shown throughout these instructions.
CONTENTS
Design Information
Product Dimensions ....................................................... 3
Models Available ............................................................ 3
Advance Plam_ing .......................................................... 3
Installation Preparation
Materials Xibu Will Need ................................................. 4
Tools Ybu Will Need ....................................................... 4
Parts Supplied ................................................................. 5
Prepare Dishwasher Enclosure ..................................... 5
Drain Requirements ....................................................... 6
Prepare Electrical Wiring ............................................... 7
Prepare Hot Water Line ................................................. S
Custom Pm_el Dimensions
Custom Panels hw PDW8000 ........................................ 9
Installation Instructions
Step 1, Remo_,e Packaging ........................................... 10
Step 2, Install Leveling Legs ....................................... 10
Step 3, Remove Access Covers .................................... 10
Step 4, Install 90 ° Elbow ............................................... ] 0
Step 5, Install Power Cord ............................................ ] 1
Step 6, Level Dishwasher. ............................................. ] 1
Step 7, Slide Dishwasher into Opening ....................... ] ]
Step 8, Cmmect _vVater Line ........................................ 11
Step 9, Comaect Drain Line ........................................ 12
Step 10, Cmmect Electrical ......................................... 12
Step ] 1, Position and Level Dishwasher. ..................... 13
Step ] 2, Pre-Test Check List ........................................ 13
Step ] 3, Dishwasher Wet Test ..................................... 13
Step 14, Secure Dishwasher
to Cabinet or Countertop ....................................... 14
Step 15, Install Toekick ................................................ 14
Step 16, Install Side Filler Strips .................................. 15
2
Design Information
PRODUCT DIMENSIONS
34"
Adjustable
to 35"
DISHWASHER MODELS
Traditional Built-In
PD_V8000 BB, Black- Accepts 1/4" or 3/4" custom
panels
PD_V8000 W_V White -Accepts 1/4" or 3/4" custom
panels
PD_V8000 CC Bisque -Accepts 1/4" oi" 3/4" custom
panels
Trim Kits
• GPF725W (white), GPF725B (black) or GPF725C
(bisque) custon_ panel kits, supports a 1/4" thick
CtlStOlI/ door panel.
• ZPF675W (white), ZPF675B (black), ZPF675C
(bisque), custon_ panel kits support a 3/4" thick
custom door panel.
Stainless Steel Built-In
PD_vV8060 SS, Stainless steel door
ADVANCE PLANNING
• These dishwashers are designed for versatility,
adaptable to virtually any installation.
• All models have a flfll length door or a modified
door to accept a fifll cabinet panel without tile
traditional access panel
• Side tub flange trim is ac!justable and will conceal
any slight gap between tile dishwasher and a(!jacent
cabinetry.
• These dishwashers may be installed beneath
countertops of stone or other materials that will not
accept screws. No trim kit required.
Standard installation in 24" deep cabinets
• In standard 24" deep cabinets, tile dishwasher door
will be flush with ac!jacent cabinetry.
• Models with 3/4" thick custom door panel will tit
flush with ac!jacent cabinetry.
Supplied or Custom Toekicks
• A 2-piece toekick is supplied with all models. Tile
toekick is height and depth a(!justable.
• Depending on cabinetry style, a custoln toekick can
also be installed to match cabinetry. Care must be
taken to assure door swing clearance above tile
toekick.
ADA-Compliant
Installation below 34" high countertops
A reduced height installation (32-1/2" rain.) beneath
a 34" co/mtertop, can be accomplished by removing
the fl'ont leveling legs. The rear legs should be
screwed in flush with the bottom support, as shipped.
Tile fl'ont of tile dishwasher i//tlSt be shimmed to
level tile dishwasher. _v_ater and electrical must be
routed through tile back wall.
Installation Preparation
MATERIALS YOU WILL NEED:
Materials Required for All Installations
[] 90°Elbow (3/8"NPTexternalthread on one end,opposite
end sizedto fit water supply)
Note: Usenew ferrule. Donot use oldparts.
[] Strain relief for electrical connection
[] Thread seal tape
[] UL Listedwire connectors (3)
[] Screwtype hose clamps
Materials For New Installations Only:
[] Air gapfor drain hose, if required
[] Waste tee for house plumbing, if applicable
[] Electrical cable or power cord, if applicable
[] Hand shut-off valve (recommended)
[] Water line 3/8" min.copper or 1/2" min.plastic (plastic
must betested for temperature and pressure)
[] Couplerfor extending drain line, if applicable
@
90° Elbow
ThreadSeal
Tape
WasteTee Valve
Air c°uO_pler
Gap
WireNuts
Shut-Off
©G
Screw Type Clamps
©
StrainRelief
ElectricalCable
or PowerCord
HotWater Line
TOOLS YOU WILL NEED:
Tools Required for All Installations
[] Phillips head and flat blade screwdrivers
[] 3/8", 5/16" and 1/4" nutdrivers
[] Level
[] Carpenters square
[] Measuring tape
[] Safety glasses WireStrippers
[] Flashlight
[] Bucket to catch water when flushing the line
[] Tubing cutter
[] Glovesto protect against sharp edges
[] Wire strippers
For New Installations Only:
[] Drill and appropriate bits
[] Hole saw set
Level
Gloves
FlatBladeScrewdriver
_ PhillipsHead
_z_, Screwdriver
SafetyGlasses _ ,4._,_,,_ _E_ _Uubtit_
NutDriver
+
Square
Hole
SawSet
Installation Preparation
PARTS SUPPLIED:
Remove the hardware accessory bag and other parts
fl'om inside or taped to the outside of the dishwasher.
Check contents against illustrations to ii'Jsure that all
parts are included.
[] 2-piece toekick
[] 6 screws (see illustration)
[] 2 leveling legs
[] Junction boxcover
Junction
BoxCover
with screws
2 Leveling Legs
e_
Screws A Screws B
(2)Countertop (2)Cabinet
Mounting Mounting
Screws Screws
Screws C
(2)Color
Matched
Toekick
Screws
PREPARE DISHWASHER ENCLOSURE
ThisWallArea
mustbeFree/
34"to35" PipesorWires
Underside 1
ofCountertop
toFloor
24"Max
• The rough cabinet opening Inust be at lea.'t 24 deep,
_35 "
2. -,/8 rain. to 24" wide. The height should be 34" rain.
add _"
_)r) Ill}IX,
Note: ADA installation, beneath 34" high countertops may be accom-
plished byremoving front leveling legs. Drain hose, water and
electrical must be routed through the cutout onthe back of the
dishwasher.
• The dishwasher must be installed so that drain hose is
no more than 10 feet in length for proper drainage.
• The dishwasher inust be flfllv enclosed on the top, sides
and back, but should not support any part of the
eI/clostlI'e.
2-PieceToekickwith
SoundInsulation
• The floor inside the opening must be even and level
with the finished floor of the kitchen, If the kitchen
floor is tile, it may be
higher than the floor of
the installation cutout,
Pieces of wood may be
placed into the cutout
floor to make it level or
higher than the room
floor, This will alh)w easy
removal fi)r any flmn'e
service,
CornerInstallation
• When installing into a
corner, allow 2"rain.
J Countertop
clearance between
dishwasher and adjacent
cabinet or wall.
• Allow 24-1/2"min.clearance
Dishwasher
from the front ofthe
dishwasher for door
opening.
, _/2"
/_ Clearancefor Door
/Opening 2" Minimum
5
Installation Preparation
DRAIN REQUIREMENTS
• Follow local codes and ordinances.
• Do not exceed ] 0 feet distance to drain.
• To prevent back flow into the dishwasher, COlmect
drain line to an air gap or use a 30" high drain loop,
depending on local codes.
• Air gap in ust be used when waste tee or disposer
COlmectioi_ is less than 18" above the floor to prevent
siphoning.
DETERMINE DRAIN METHOD
The type ot drain iI_stallati(m depends (m the fl)llowing
questions.
Do local codes or ordii_ances reqtlii'e an aii" gap?
Will waste tee or disposer COlmectioi_ be less than 18"
above the floor?
Will installation have a high drain loop less than 30"
above the floor?
If the answer to ANYof these questions is YES, Method 1
MUST be used.
• If all answers are NO, either inethod inay be used.
.M_ air gap MUST BE USED if the drain hose is con-
nected to a waste tee or disposer lower than 18" above
the floor level.
• Faihu'e to provide the proper drain COlmectioi_ using
an air gap or a 30" rain. high drain loop will result in
ilnproper drailfing of the dishwasher which inav cause
damage or poor wash peril)finance.
Method 1 - Air Gap with Waste Tee or Disposer
An air gapmust be used when the waste tee or disposer
connection is less than 18" from the floor.
Method 2 - High Drain Loop with Waste Tee or
Disposer Install waste tee or disposer and air gap according
to manufacturer's instructions.
l-
CABINET PREPARATION
• Drill a 1-1/9" dia. hole in the cabinet wall within
the shaded areas shown for the drain hose Colmec-
tion. The hole should be Slnooth with no sharp
edges.
ll DOlT YAVOIR tree coupure ai_tirefl)ulemei_t si le
ttlvat! de vidange est branch6 sur un raccord d'6gout ou
tin broyeur d'ordures a inoins de 46 cln (18 po) du sol.
• Si la vidange n'est pas branch_e correctement en
utilisant tree coupure ai_tirefoulelnei_t ou tm boucle
d'_gout d'au moins 76 Cln (30 po) de haut,
l'_coulemei_t de l'eau du lave-vaisselle n'est pas boil
ce q ui petit causer des dolmnages ou tm inauvais
lavage de la vaisselle.
Installation Preparation
PREPARE ELECTRICAL WIRING
FOR PERSONAL SAFETY: Remove
house fllse or open circuit breaker
before begimfing installation. Do not use
an extension cord or adapter plug with
this appliance.
POUR ASSURER LA S1_CURIT1_
PERSONNELLE, il flint enlex er le fllsible
ou couper le courant au disjoncteur
axant de commencer l'installation. Axec
cet appareil, il ne taut pas utiliser de
r
ralhmge ni d'adaptateur de prise.
Electrical Requirements
• This appliance must be supplied with 120V, 60 Hz., and
com_ected to an individual properly grounded branch
circuit, protected by a 15 or 90 ampere circuit breaker or
time delay fllse.
• Wiring must be 2 wire with ground and rated for 75°C
(176°F).
• If the electrical supply does not meet the above require-
merits, call a licensed electrician betore proceeding.
Grounding Instructions-Cable Direct
This appliance must be (mmected to a grom_ded metal
perlnai_ei_t wiring system, or an equipment-grounding
con ductor must be r/In with the circuit con ductors an d be
com_ected to the equipment-grounding terminal or lead
on the appliance.
Black
" Cabinet
White
2"
Electrical Connections to Dishwasher:
The dishwasher junction box is located on the right side
at the fl'ont of the dishwasher. The electrical cable must
extend forward at least 24" to reach the junction box
when dishwasher is installed.
• The wiring inav enter the opening from either side,
rear or the floor within the shaded area.
• Cut a 1-1/9" max. dia. hole to admit the electrical
cable or use the same hole cut tor the drain hose. The
hole inust be flee of sharp edges. If the cabinet wall is
metal, the hole edge must be covered with a bushing.
• For power cord cmmections, install a 3-prong ground-
ing type receptacle in the sink cabinet rear wall, 6"
rain, or 18" max. fl'om the opening, and 6" to 18"
above the floor.
Grounding Instructions-Power Cord
This appliance Inust be gromMed. In the event ot a
malflmction or breakdown, grounding will reduce the risk
of electrical shock by providing a path of least resistance
fin" electric current. The plug must be plugged into an
appropriate outlet that is installed and grounded in
accordance with all local codes and ordinances.
The improper cmmection of the eq uip-
merit-grounding conductor can result in
a risk of electric shock. Check with a
qualified electrician or service represen-
tative if vou are in doubt that the appli-
ance is properly gromMed.
I'!_ll;/'|!aiI,"I,"I!K',I!t'I
Le mauvais branchement du fil de raise h
la terre de l'&luipement petit causer tm
choc _lectrique. En cas de doute sin" la
raise h la terre de l'appareil, consulter un
_lectricien qualifi_ ou un repr_sentant
teclmiq tie.
Installation Preparation
PREPARE HOT WATER LINE
The line may enter fl'om either side, rear or floor
within the shaded area shown.
• The water line may pass through the same hole as
the electrical cable and drain hose. Or, cut an
additional l-1/2" dia. hole to admit the line. If a
power cord with plug is used, it must pass through
a separate hole.
Water Line Connection
• Turn o11 the water supply.
• Install a hand shut-otI valve in an accessible loca-
tion, such as under the sink. (Optional, but strongly
recommended and may be required bv local codes.)
• The hot water line should be 3/8" O.D. copper
tubing or 1/2" O.D. plastic tubing. The line must
extend forward at least 30" fl'om the left side or 40"
fi'om the i'eai" wall.
• The water line illtlSt be hmg enough to form a
smooth natural loop with no sharp bends or kinks
between the cutout entry.
i\
/
Shut-offValve
\
,,_
ii
ii
Hot[]::::
ii
ii
ii
CabinetFace_
/
fromWall 2" fromFloor
i \
\
• At!just water heater to deliver temperatures of 120°F to
150°F.
• lqush watei" line to clean out debris.
• The hot water supply line pressure must be 90-190 PSI.
Custom Panel Dimensions
CUSTOM PANEL FOR MODELS
PDW8000
Panel kits must be ordered separately. Installation
of any custom panel should be completed before
the dishwasher is installed.
1/4" PANEL WITH GPF725 TRIM KIT
1/4"Thick I
DoorPanel 25-1/4"
23-1/8"
• Cut the panel to the climensions shown.
• The bottom left and right coi'nei's should be ctlt at
1/4" radius. See illustration.
3/4" PANEL WITH ZPF675 TRIM KIT
The ctlstom panel size xaries depending on your
installation.
Countertop Custom
Cabinets
S Floor -_11_
/Bottom of 3/4" Max.
AdjacentCabinetry
* Height is equal to A minus 5-3/8"
EXAMPLE:A =30-1/2" minus 5-3/8"is equalto 25-1/8".
1. Measure Dimension A, fl'om underside of countertop
to bottom of a(!jacent cabinets.
2. Subtract 5-3/8". Control panel height is 5-1/8"..Mlow
1/4" clearance between countertop and control
panel.
3. The custom panel fits against bottom of the control
panel.
A
Panel Size
Top
DoorPanel
3/4" Thick _Helght
23-1/8"_
Installation Instructions
BEFORE YOU BEGIN:
CUSTOM PANEL INSTALLATION: Ifvou intend to
install custom door panels, (on some models) refer to
trim kit installation instructions. Custom panels should
be in place bet0re installing tile dishwasher.
ISTEP 1] REMOVE PACKAGING
Cut tile shipping carton and use it as a pad beneath tile
dishwasher. This will protect tile finished floor in tile
kitchen.
• Remove wrapping and uncoil tile drain hose in tile
back of tile dishwasher. Do not remove rear insulation
blanket,
• Lay the dishwasher on it's back, Do not kink or crush
the drain hose,
[STEP 2] INSTALL LEVELING LEGS
lSTEP31REMOVE ACCESS COVER
AccessCoverJuncti°_c"
• ReIllOX e sol/nO instllation board and tile access coxer
plate.
• Install UL listed strain relief on.jUllCtioi_ box.
Min.
Rernove
RedPlugs
Unscrew
Rear Installation
Insulation Height
Blanket
• Measm'e installation opening fi'om tile floor to tile
bottom of tile co/mtertop.
• Install tile fl'ont leveling legs into holes on tile brack-
ets. Use a wrench to screw tile legs in until tile overall
height of tile dishwasher is 1/4" less than tile installa-
tion opening height.
Note: InstaU the legs as shown, 1-1/4" min from the
bottom of the bracket.
• Remove and discard tile red plugs fl'om tile fl'ont
holes.
RearLegsto
lSTEP 41 INSTALL 90 ° ELBOW
• Install tile 90 ° elbow onto tile water inlet. Use thread
seal tape or pipe thread compo/md. Thread seal tape
should be wrapped in sam e direction as tile threads on
tile elbow.
• Tile 90 ° elbow should time tile inlet water line.
10
Installation Instructions
[STEP 5] INSTALL POWER CORD
SKIP THIS STEP IF DISHWASHER
WILL BE DIRECT WIRED
• Maxim mn power cord length is 6 ft.
• The power cord and connections must comply with
the National Electrical Code, Section 422 and/or
local codes and ordinances.
Insert power cord wires
through strain relief and
tighten.
• Strip 1/2" insulation
fi'om ends of power
cord wires.
• Comlect incoming power cord white to dishwasher
white, black to black and grom/d to dishwasher green
wire. Use UL listed wire c(mnectors of appropriate size.
• Install junction box cover with screws provided. Be sure
wires are not pinched under the cover.
[STEP 7] SLIDE DISHWASHER
INTO OPENING
DO NOT PUSH AGAINST THE FRONT PANEL WITH
KNEES, DAMAGE WILL OCCUR!
• Insert draii_ hose into the cabinet wall hole. If a power
cord is used, guide the end through a separate hole.
• Position water supply line and house wn'ing on the
floor of the opening to avoid interterence with base
of dishwasher.
• Slide dishwasher into the opening a Jew inches at a
time. As you proceed, pull the drain hose through the
cabinet wall under the sink.
• Check to be sure there is 11o interterence with
waterline or house wiring.
• Again, check to be sure the dishwasher is level.
[STEP 61 LEVEL DISHWASHER
• Careflflly, upright the dishwasher, be careful not to
bend the leveling legs.
• Check to be sm'e the dishwasher is level and is
ac!justed to fit the installation cutout height.
Level
Top
and
Sides
[STEP 8] CONNECT WATER LINE
NOTE: If you are using an existing water line, cut 1" off
the end. Always use a new ferrule and compression mlt.
• The water supply line should be flushed to clear anv
fi)reign material betore c(mnecting to the dishwasher.
• Make sure there are 11o sharp bends or kinks to restrict
water flow.
• Insert water line into the 90 ° elbow.
• Slide terrule against
elbow and secm'e with
COll/pFession n/lt.
• Replace access panel
plate.
11
Compression Nut
90° Elbow SupplyLine
HotWater
Installation Instructions
[STEP 9] CONNECT DRAIN LINE
FOLLOW ALL LOCAL CODES AND ORDINANCES.
• The dishwasher is supplied with a 72" long drain hose.
• If a hmger drain hose is required, add up to 48" of
length for a total of ]0 ft. length.
• Secure the drain hose to the air gap, waste tee or
disposer with damps.
• Make sm'e drain hose is not kinked.
IMPORTANT: When comaecting
drain line to disposer, check to be
sure that drain plug has been
[_4_ Remove
removed, DISH_VASHER WILL
NOT DI_MN IF PLUG IS LEFT
IN PIACE,
Method 1 - Air gap with waste tee or disposer
Waste Tee Installation
DisposerInstallation
Method 2 - High drain loop with waste tee or disposer
Waste TeeInstallation
Plug
[STEP 101 CONNECT ELECTRICAL
FOR DIRECT WIRE ONLY
(If a power cord with plug is used, plug it into the wall
outlet and continue with next step.)
turned off at the
source.
Verify that power is o_ )
Insert power cord wires
through strain relief and
tighten. -White
• Locate the three dishwasher wires, (white, black and
green) with stripped ends. Insert wire through the
small hole in the junction box. Use wire com_ectors to
comaect incoming grotmd to green, white to white and
black to black.
• Install junction box cover with screws provided. Check
to be sure that wires are not pinched under the cover.
• Reinstall Insulation Board in position. The board
should be secm'ed so it does not interfere with door
opening.
6r
Fastento underside
_ ___ of countertop
Waste Tee Installation
Fasten to underside
_ of countertop
Disposer Installation
30"
If house wiring is not 2-wire with
gromM, a gromM must be provided
by the installer. When house wiring is
alumimmL be sure to use/JL Listed
anti-oxidant compomM and alumi-
n/llIl-to-coppeI" connectoFs,
Si l'installation _lectrique de la maison
n'est pas h deux ills plus terre,
l'installateur dolt installer tm fil de
raise h la terre. Si l'installation
_lectrique de la maison est en alu-
minium, il flint prendre soin d'utiliser
des compos_s antioxydants et des
connecteurs aluminium h cuivre sur la liste UL.
12
Installation Instructions
ISTEP 111 POSITION AND LEVEL THE DISHWASHER
• Check to be sure the dishwasher is a(!justed to coiTect
height and is centered in the cutout.
• Open and close the door to insure proper operation of
the door. If there is any binding or rubbing, reac!just
leveling legs.
Use awrench to make adjustments.
• If the door rubs on the right side ofthe cabinet, extend the left rear
leg by unscrewing it one quarter turn.
• If the door rubs against the left side ofthe cabinet, extend the right
rear leg by unscrewing it one quarter turn.
• Checklevel again. Repeatthe procedure if necessary.
ISTEP 12 1PRE-TEST CHECK LIST
Installation service calls are not covered by your
warranty, To avoid unnecessary charges, review
this list carefully.
[] Checkto be sure power is OFE
[] Open the door and remove all foam and paper packaging.
[] Pull lower rack out, about halfway. Check to be sure it does
not roll back or forwards on the door. If the rack moves,
adjust leveling legs.
DoorRub
OnRight OnLeft
Adjust Adjust
This This
Leg Leg
[] Verify water supply and drain lines are not kinked or in contact
with other components.
[] Turn on the sink hot water faucet and verify water temperature.
Incoming water temperature must be between 120°Fand 150°E
120°Fmin. temperature is required for best wash performance.
[] Turn on water supply.
[] Openthe door. Checkto be sure Insulation Board does not
interfere with door opening.
STEP 13 I DISHWASHER WET TEST
[] Turn on power supply.
[] Select the normal cycle and press the start button.
[] The control will indicate a slow/no fill by flashing the CHINA
CRYSTAL LIGHTWASH ORWASH CYCLElight. Check water
supply, then adjust fill time according to the chart shown.
[] Check to be sure that water enters the dishwasher, wait up to
2minutes. Ifwater does not enter the dishwasher, check to be
sure that water is turned on.
[] Check for leaks under the dishwasher. If a leak is found, turn
power and water off, then tighten connections. Restore power
andwater supply.
[] Check for leaks around the door. A leak around the door could be
caused by door rubbing or hitting against adjacent cabinetry.
Reposition the dishwasher if necessary.
[] After the dishwasher drains check drain lines. If leaks are found,
turn power off, correct as necessary.
[] The control will indicate a slow/no drain by flashing the RINSE
ONLY,SANI WASH or HEATOPTIONS.Check that the airgap is
clear of debris and that the knockout in the disposer or waste tee
is fully removed. Check that the drain hose is not kinked.
[] Open the dishwasher door and make sure that most of the water
has drained. If not, check that disposer plug has been removed
andthat air gap is not plugged.
[] Cancel the dishwasher cycle and complete the installation.
[] Remove protective film if present from the control panel and door.
CHECK WATER FILL LEVEL
For best performance, check the water fill level.
Runthrough a complete RINSE ONLYcycle to ensure it is emptying
and filling correctly. For low water pressure situations run the
RINSE ONLYcycle 3 times. Half-way through the final RINSEONLY
cycle, pause the dishwasher and check the water level inside the
dishwasher. If the water level is not above the minimum water level
(marked on the lower spray support tower), increase the fill level.
1.Ensure the dishwasher is not running through a cycle. Depress
the WATERTEMP button for 10seconds until the second buzzer
sounds (except on ZBD6600).
2. Press the START/CANCELbutton to select fill time, as per chart
(65seconds is the factory setting).
3.To test time, press DELAYSTART.The dishwasher will start filling.
Listen for the dishwasher to complete filling. Once filled, the fill
level must be checked to ensure fill time is correct.
4. Once complete, press the WATERTEMP button to exit fill time
mode.
Continue to press the START/CANCELbutton
until the desired indicator is illuminated.
CycleStatue Indicators Fill Time
SENSING 60seconds
WASHING 65seconds
RINSING 70seconds
DRYING 80seconds
CLEAN 90seconds
13
Installation Instructions
[STEP 14] SECURE DISHWASHER
TO CABINET AND
COUNTERTOP
To maintain position and aligmnent, it is rec(nmnended
tile dishwasher be secured to tile countertop and
a(!jacent cabinets.
Secure dishwasher to countertop:
• Drill pilot holes through tile mounting bracket and
into tile underside of tile countertop. Secure with
screws A provided.
Screw_
[STEP 151 INSTALL TOEKICK
• Loosen depth a(!justment screws inside tile bracket.
• Slide bracket out
to proper depth.
Tighten screws.
• Attach supplied Adjustto
toekick to Toekick
brackets with Depth
screws C provided.
Do not tighten.
• A(!just tile toekick
to to/ich the floor.
Tighten screws.
AttachmentScrews
Adjust to Touch Floor
IMPORTANT: To avoid damage to your dishwasher,
drive screws straight and flush. Protruding screw heads
may scratch the top of the escutcheon or door and cma
interfere with door closing.
Secure dishwasher to adjacent cabinets:
• Remove plastic plugs button on tile inside of tile
dishwasher fl'ame. One on each side.
• Drill pilot holes through tile dishwasher holes and
into tile a(!jacent cabinets. Install screws B provided.
• Replace plastic plug buttons.
Screw B
14
Installation Instructions
[STEP 16] ADJUST SIDE
FILLER STRIPS
• Open the door fldlv.
• Loosen (but do not reinove) screws holding the top
and side ti'iI/lS.
• A(!just triIll to cover opening gap. Tighten screws.
AdjustSideTrim
to MeetCabinetry
15
Note: While performing installations described in this book,
safety glasses or goggles should be worn.
Note: Product improvement is a colltilltlhlg c[lde_wor at
General Electric. Therefore, materials, appearance and
specifications are sul{iect to change without notice.
0616400350 I
Pub.No.31-30545
Dwg.No.203C1559P085
(N.D.318) 11/01
Loading...