GE PFSF5NJWAWW, PFSF5NJWACC, PFSF5NJWABB, PFIC1NFWCWV, PFIC1NFWCBV Owner’s Manual

...

ge.com

Safety Instructions ........... 2, 3

Operating Instru_tions

Additional Features ............. S

Automatic Icemaker ........... 11

Care and Cleaning .......... 12-13

Controls .................... 4-5

Crispers and Pans .............. 9

Freezer ...................... 10

Repl acing the i,igh t Bulbs ....... 14

Shelves and Bins ............. 7, S

_'ater Filter . .................. 6

Installation InsTtructions

Installing the Anti-Tip

Floor Bracket .............. 18-19

Installing the Refrigerator .... 20-24

Installing the _'ater Line ..... 33-35

Preparing to Install

the Refligeratnr . .............. 17

Removing and Replacing the

Freezer Drawer . ........... 25, 26

Reversing the Door Swing

(Single Door Refrigerator

Models only) .............. 27-29

Removing and Replacing the Doors (Double Door

Refrigerator Models only) .... 30-32

Trim Kits and Decorator

Panels .................... 15-16

Models21 and25

Cong_lateur inf&ieur

R frig rateurs

La section fran_aise commence a la page 49

Congelador inferior

Refrigeradores

La secci6n en espa#ol empieza en /a pagina 93

Troubleshooting Tips ....... 36-40

Normal Operating Sounds ...... 36

Consumer Support

Consumer Support ..... Back Cover

Performance Data Sheet ........ 47

Product Registration

for Canadian Customers ..... 43, 44

Product Registration

fox U.S. Customers ......... 41,42

State of California ¼'ater

Treatment Device Certificate ..... 48

¼'arranty fox Canadian

Customers ................... 46

V(arranty fox U.S. Customers ..... 45

Writethe modelandserial numbershere:

Model # Serial #

Find these numbex_ on a label on the right side, near the top of

the refrigerator compartment.

200D9366PO01 49-60489-2 06-07JR

iMPORTANTSAFETYiNFORMATiON. READALLiNSTRUCTiONSBEFOREUSING.

WARNING!

Use this appliance only for its intended purpose as described in this Owner's Manual.

SAFETYPRECAUTIONS

When using electrical appliances, basic safety precautions should be followed, including the following:

_:i:This refl-Jgerator must be properl_ installed

and located in accordance with the Installation Instructions before it is used.

i)::Do not allow children to climb, stand or hang

on the shelves in the refl'igeratm: They could damage the refi_igerator and seriously injm'e

themselves.

::_Do not touch the cold sm'fi_ces in the fl'eezer

compartment when hands are damp or wet. Skin mm stick to these extremely cold stmfi_ces.

i?<Do not store or use gasoline or other flammable

vap(n_ and liquids in the vMnitv of this or anv other appliance.

i)::Keep finge_ out (ff the "pinch point" areas;

clearances between the do(n_ and between the (loo_ and cabinet are necessarily small.

Be careful closing (lores when children are in the area.

i(i'In refl_igeratm5 Mth automatic icemake_s,

avoid contact with tile moving parts (ff tile

ejector mechanism, or with tile heating element that releases tile cubes. Do not place finge_ or hands on tile automatic icemaking mechanism

while tile refl_igerator is plugged in.

i!:i'Unplug tile reliigerator before cleaning and

making repai_.

NOTE: Westronglyrecommendthatany servicingbe

performedby aquafified individual

i(i,Setting either or both controls to 0 (off) does

not I'ell/OVe power to tile light (-iI'('tlit.

i::tDo not refl'eeze frozen fi)ods which have

thawed complemly.

DANGER!RISKOFCHILDENTRAPMENT

PROPERDISPOSALOFTHEREFRIGERATOR

Refrigerants

of tile past.Junked or abandoned refl_igerat(n_ are Child entrapnlent and suffocation are not problems

still dangerous...exert if they will sit for 'ijust a few daxs." If _ou are getting rid of _om" old refri(*erat(m

please follow tile instructions below to help prevent accidents.

Before YouThrew Away YourOldRefrigerator

All refl'igeration products contain refl'igerants, which tinder federal law InUSt be relnoved prior

to product disposal. If you are getting rid of an old refl'igeration product, check with tile

company handling tile disposal about what

to do.

or Freezer:

iJi::_ke off tile dome.

iJi::i,eaxe tile shelves in place so that children may

not easiE climb inside.

USEOFEXTENSIONCORDS

Because of potential safety hazards under certain conditions, we strongly recommend against the use of an extension cord.

However; if you must use an extension cord, it is absolutelx necessary that it be a UiTlisted (in tile United States) or a CSA certified (in Canada),. -_are ,gr°tmding, t_,])e appliance extension cord having a grotmding

t)])e I)lu(*_and outlet and that the electrical rating of the cord be 15 amperes (minimum) and 120 xolts.

WARNING!

HOWTOCONNECTELECTRICITY

Donot, under any circumstances, cut or remove the third (ground) prong from the power cord.

For personal safety, this appliance must beproperly grounded.

ge.com

The power cord of this appliance is equipped

with a 3-prong (grounding) plug which mates with a standard 3-pr(mg (grounding) wall outlet to

minimize the possibiliQ, of electric shock hazard fl'om this appliance.

Have the wall outlet and circuit checked by a qualified electridan to make sure the outlet is

properly grounded.

Where a standard 2-prong wall outlet is

encountered, it is your personal responsibiliQ' and obligation to have it replaced with a properly

grounded 3-prong wall outlet. The reli-igerator should alwa D be plugged into its

own individual electrical outlet which has a voltage rating that matches the rating plate.

This provides the best pe_om_ance and also I)rexents oxerloading, house wiring circuits which

could cause a fire hazard fl'om oxerheated wires.

Never unplug your refrigerator bv pulling on the power cord. Mways grip plug firefly and pull

straight out fl'om the outlet.

Repair or replace immediately all power cords that have become fl'ayed or othe_Mse damaged. Do not

use a cord that sho_:s cracks or abrasion damage along its length or at either end.

\,_]_en moving the refrigerator away fl'om the wall, be careflll not to roll over or damage the power cord.

READANDFOLLOWTHISSAFETYINFORMATIONCAREFULLY.

SAVETHESEINSTRUCTIONS

Aboutthe controlswith temperaturesettings.

(onsomemodels)

[]

[] []

Hold 3 seconds to _eset NoEd 3 seconds

WARMER _ _WARMER

COLDER COLDER

0oF Recommencled 37- F Recommended

TEMPERATURE SET

[]

(onsomemodels)

NOTE: Therefrigeratoris shipped with protective film coveringthe temperaturecontrols. If this film was not removedduringinstallation, removeit now

Thetemperature controls are preset in the factory at 37°F for the refrigerator compartment

and O°Ffor the freezer compartment. Allow 24hours for the temperature to stabilize to the

preset recommended settings.

Thetemperature controls can display both the SET temperature as well as the actual temperature in the refrigerator and freezer. The actual temperature may vary slightly from the SETtemperature based on usage and operating environment.

Setting either or both controls to OFFstops cooling in both the freezer and refrigerator compartments, but does not shut off electrical power to the refrigerator.

Changingthe Temperature

For Controls-on-the-DoorModels:

To change the temperature, press and release the WARMER or COLDER pad. The ACTUAL TEMPlight

will c(nne on and the display will show the actual temi)eratm'e. To change the temperature, tap

either the WARMERor COLDERpad tmtil the desired temperature is displayed.

For ControlsInside the Refrigerator:

Opening the door displa):s the actual temperature. To change the temperature, press either the

WARMER or COLDER touch pads tmtil the

desired temperature is displayed.

Once the desired temperature has been set, the temperatm'e display will return to the actual

i'efi-Jgei'ator and fl'eezer teil/perattlres aftei" .5 seconds. Several ac!iustments may be required.

Each time )ou ac!iust controls, allow 24 horns fin" the refrigerator to reach the temperature you haxe set.

To turn the cooling system off, trip the WARMER pad

fro" either the refl_igerator or the fl'eezer tmtil the display shows OFF. To turn the unit back on, press the

COLDER pad for either the refl_igerator or fl'eeze_:

Then press the COLDER pad again and it will go to the preset points of O°Ffi)rthe fl'eezer and 37°Ffi)r

the refi_igeratox: Setting either or both controls to Off stops cooling in both the fl'eezer and

refl_igerator compartments, but does not shut off electrical power to the refi_igeratm:

About TurboCooEM(onsome models) ge.oom

Turbo €O01

(onsomemodels)

(on some models)

How it Works

TurboCool rapidly cools the retiigerator

colnl)artinexlt ixl order to inore quickly cool fi)o(ls. Use TurboCool when adding a

large anlount of toed to the refligerator comi)artn/ent, putting away fi)ods after they

have been sitting ()tit at i'OOlll temperature or when putting away waml letterers. It can

also be used if the refiigerator has been

without power for an extended period.

Once acti\:_md, the compressor will turn oil immediateh and the rims will cycle on and off at high speed as needed for eight hom_.

The compressor will continue to mn tmtil the refi_igerator compartment cools to

approximately 34°F (1 °C), then it will cvcle on and off to maintain this setting. ?dter 8

hom_, or if TurboCool is pressed again, the refl_igerator compa rtm ent will return to

the original setting.

About Door Alarm (onsomemodels)

The door alaml will somld if any

dooI" is open _()I" I//oI'e [l/}lI1 2 IlllIltlte,_,

The beei)im,_ stops when you, close

the door,

How to Use

Press TurboCool.The retiigerator temperature display will show ccc.

_Mter TurboCoolis complete, the

refl_igerator compartment will retm'n to the original setting.

NOTES:The refrigerator temperatm'e

cmmot be changed dining

rurboCooL

The fl'eezer temperature is not affected during TurboCool.

When opening rite refrigerator

door during TurboCool,the fires

will continue to mn if they have

cycled on.

(onsomemodels)

_ ii _ i I i i ii_ i

(. ALA..DOORli ¸

iiiii iii _ii

on somemodels)

(onsomemodels)

About Energy Saver (onsomemodels)

This product is equipped with an Energy/

Saver featm'e. The refl_gerator is shil)ped

with the Energy' Saver teatm'e enabled.

Over time, moisture can timn on the fl'ont surli_ce of tile refl_igerator cabinet and cause i'tlSt. If moistm'e does appear on the

front surfi_ce of the refligemtor cabinet,

tm'n off the Energy Saver ti_atm'e by pressing and releasing the ENERGY SAI/ER

pad on the control panel.

(onsomemodels)

Aboutthe water filter.(onsomemodels)

Water Filter Cartridge

The water filter c;u_fidge is located in the back upper fight corner of the refi'igerator

COl//pll 1"_1//ellt.

When to Replace the Filter

There is a replarement indicator light tbr tile water filter ca_qh-idge on the

temperature display. This light will turn

(mmge to tell you that you need to replace

the filter soon. The filter cam-idge should be replaced when the replacement

indicator light ttlrns red or if tile flow

of water to tile dispenser or icemaker decreases.

Installing the Filter Cartridge

0 If you are replacing the cartridge,

first rem_we tile old one. Open the cariridge cover by pressing ill on tile tab at tile fi'ont and pulling down.

0 Remove tile cartridge b} sloxd} rotadng

it counter clocBvise. A small amount of water may drip down.

Filter Bypass Plug

_i_u must use tile filter b}pass plug when a

replacement filter camJdge is not available. Tile icemaker will not operate without tile

filter or filter b}])ass plug.

Replacement Filters:

To order additional filter cartridges

in the United States, visit our Webs#e, re.corn, or carl GE Parts and Accessories,

800.628.2002.

Filter Model (;S\'_TF

(Mstome_s in Canada shoukl consult the } ellow pages for tile nearest Mabe

Service Centre:

Water Filter

Hold 3 Secs

(on some models)

Z m

I RESET1/7

FILTER J

Hold 3 SecondstO reset

(on some models)

CAUTION: been

/nthesystem,thefi/tercartridgemaybeejectedas it/s removed.Usecautionwhenremoving

0 Remo_e the protecti_ e foil from tile

end of tile camJdge.

I,ining up tile arrow on tile calqhidge and the ca_qtfidge holder; slowly rotate

the cartridge clockwise until it stops. \_l_en tile ca_fidge is properly

installed, yon will ieel it "click" as it locks into place. The grip on the end

ot tile cartridge sb.ould be positioned _w_icallv. Do notovertighten.

0 (lose tile camidge co\w:

0 I_,tm water fi'om tile dispenser for

3 minutes (about l/2 gallons) to clear the system and pre\vnt sputtering.

See ToUsetheDispensersection.

Press and hokl the RESETWATERFILTER pad ibr 3 seconds.

NOTE"A newly-installed water filter cartridge

may cause water to spurt ti'om tile dispense_:

Abouttheshelvesandbins. gecem

Not all features are on all models.

Rearranging the Shelves

Shel',es in the refl_igerator c()ml)artn_ent are a(!justable.

Refrigerator Compartment

To remove:

0 ]_emo_e all items fl'om the shelf.

O Tilt the shelf up at the fl'ont.

O I,ifi the shelf III) at the back and

Some models have wire shelves that can be adjusted in the same mam?er.

bring the shelf out.

To replace:

_qfile tilting the shelf I/I), insert the top

hook at the back of the shelf ill a slot on the track.

@ I,ower the fl'ont of tile shelf until the

bottom of the shelf locks into place,

i 0

Spillproof Shelves (onsomemodels)

SI)illproof shelves have special edges to hel I) I)revent spills fl'oln dI'iI)ping to lower

shelves. To relnove or replace the shelves, see Rearranging the Shelves,

Slide-Out Spillproof Sheff (onsomemodels)

The slide-out si)illproof shelf allo_v_ you to reach itelns stored behind othei_. The

spedal edges are designed to hel I) prevent

spills fl'om dripping to lower shelves.

Toremove:

Remove all items ti'om shel£

0 Slide the shelf otlt iintil it stops.

Lift the fi'ont edge of the shelf until the central tabs are above the fl'ont hal:

O (_ontinue i)ulling the shelf t0rward

until it can be relnoved.

Toreplace:

Place the rear shelf tabs just in fl'ont of the central notches on the shelf fl'ame.

Slide the shelf ill until the central tabs are slightly behind the fl'ont bin;

O i,ower the shelf into place until it is

hoi-izontal and slide the shelf ill.

Makesurethattheshelfsitsflatafterre/bsta//ation anddoem'tmovefreelyfromsidetoside.

Makesureyoupushtheshelvesa//thewayin beforeyoudosethedoor

Abouttheshelvesandbins.

Adjustable Bins on the Door

Ac!iustable bins can easily be carx_ied ti'()m

I'eti_igeI'_l[oI" 1o w()x'k _lI'e_l,

To remove: I,ifi bin straight up, then

pull out.

To replace or relocate: Slide in the bin j ust

above the molded door supports, and push down. The bin will lock in place.

Non-Adjustable Bins on the Door

To remove: Lift the bin straight ui), then

pull out.

To replace: Engage the bin in the molded

supports on the door and push do_n.

It will lock in place.

Abouttheadditional features.

The snuggerhelps prevent tipping, spilling

or sliding of small items stored on the door shelf. (h_iI) the finger hold near the rear of the snugger and move it to fit w)ur needs.

Not all features are on all models.

Non-Adjustable Beverage Rack

To remove: Lift the rack straight up, then

ptfll out.

To replace:Engage the rack in the molded

SUl_l_orts on the door and push down.

It will lock in place.

Aboutthe crispersandpans. gecem

Not all features are on all models.

Fruit and Vegetable Crisper

Excess water that mm accunmlate in the bottom of the (h'awe_ or under the (h'awe_

should be wiped dry;

Adjustable Humidity Crisper (onsomemodels)

Slide the control all the way to the Slide the control all the wax to the LOW

HIGHsetting to proxide high humidit_ ,settino-_to proxide lower humidi_' lmels recommended for most xegetables, recomm ended fiw most fl'uits.

Adjustable Temperature Deft Pan (onsomemodels)

Slide the control all the way to the left for

the coldest temperature.

How to Remove and Replace the Deft Pan

Toremove:

0 Remoxe the ti'uit and xegetable (h'awei_. @Pull the drawer ()tit to the stop position.

'ingLocks 0 I,ifl the lid to access the 4 swing locl_s.

Rotate all fimr ,sxdn,*_locks to the unlock position.

0 Lilt the fl'ont of the drawer up and ()tit.

Toreplace:

Make sure all tour swing locks are in the

unlock position.

@ Place the sides of the drawer into the

drawer supports, making sure the swing

locks fit on the drawer slots.

I,ock all fimr swing locks by rotating

them to the lock position.

0 i,ower the lid and slide in the drawer

Replace the fl'uit and xegetable (h'awei_.

J J

Aboutthe freezer.

Not all features are on all models.

Freezer Shelves and Baskets

O A shelf abo\v the ice storage bin

Appearance and features may vary

Basket Removal

To remove the deep full-width basket on

freezer drawer models:

O Open the fl'eezer drawer until it stops.

O The fl'eezer basket rests on the inside

_]b Lift the basket so that all 4 tnbs are out

Appearance may vary

A haltZwidth basket A shallow filll-width basket

A deep flfll-width basket

tnbs on the drawer slides.

of the slide bracket.

Tilt the basket and lift out of the

drawer,

When replacing the deep full-width basket

Tilt the basket back and lower it down

into the drawe_: Rotnte the basket to a horizontnl position and press it down into

the 4 aligmnent tabs,

NOTE:M_m_sbe sm'e that all 4 basket tnbs

are engaged in the slide brackets befl)re sliding back into the fl'eezet:

Appearance may vary

0 Make sm'e the plastic sleexes remain

attached to the 4 tnbs on the slide

brackets.

To remove the half-width basket:

Ptfll the basket out to the stop location.

Lift the basket up at the fl'ont to release it from the slides,

0 Lift the back up and out of the slide.

)

When replacing the basket, make sure that

the wire tnbs and wire hooks on the sides oI the basket go into the slots in the top

ot the uI)per basket slides.

NOTE:Mw'a_:sbe sure to flfllv close this

basket.

Toremove the shallow full-width basket:

Ptfll the basket out to the stop location.

Lift the ti'ont up and oxer the stop location.

0 Lift the basket up and out.

Appearance may vary

Abouttheautomaticicemaker, ge.cem

A newly installed refrigerator may take 12to 24 hours to begin making ice.

Power Automatic Icemaker (on some models) Switch

Green

PowerLight

Icemaker

The icemaker will produce seven cubes per cycle---al)l)roxin_ately 100-130 cubes in a 24-hour period, del)ending on fl'eezer

coi/lpai'tlllent tei/lpei'attli'e_ i'ooi/1

temperature, nmnber of door openings and other use conditions.

See below flit how to access ice and reach the power switch.

If the refl_Jgerator is operated befin'e the

water c(mnecfion is made to the icemake_, set the power switch in the 0 (off) position.

When the refl_Jgerator has been connected

to the water SUl)l)ly, set the power switch to the I (on)position. The icemaker power

light will turn green when the fl'eezer light switch is pressed in or when the fl'eezer

door is ch)sed.

The icemaker Mll fill Mth water when it

cools to 15°F (-10°C), A newly installed reflJgeratof Ill}IV take ] 2 to 24 hotlI'S to

begin making ice cubes.

You xfill hear a buzzing sotmd each dine

the icemaker fills with water:

Throw awax the first tew batches of ice to allow the water line to clea_:

Be sm'e nothing interteres with the sweep of the teeler amL

When the bin fills to the level of the teeler

am_, the icemaker will stop produdng ice. It is nomml fin" several cubes to be

joined together:

If ice is not used fl'equenfly, old ice cubes

will become ch)udy, taste stale and shrink.

NOTE."Inhomeswith lower-than-averagewater pressure,you mayhear the icemakercycle multiple times whenmaklbg onebatch of ice.

NOTE,"Setthepowerswitchtothe0 (off)position

if the watersupplyisshutoff.

Shelf

Toroach the power switch.

i!iii_i

DispenserCradle

SpillShelf

Accessing Ice and Reaching the Power Switch

To reach the icemaker power switch, pull the

shelf al)oxe the ice bin straight ()tit. _Mways be sm'e to replace the shelf.

Toaccess ice, simpl) pull the bin fi)rward.

Icemaker Accessory Kit

If )ore" refrigerator did not come ah'eadv equil)ped with an automatic icemake_,

an icemaker accessorx kit is axailable at

extra cost,

ToUsetheDispenser

Press the glass gently against the top of the dispenser cradle.

The spill shelf is not sel6(h'aining. To

reduce water spotting, the shelf should be

cleaned regularly.

If nowaterlsdispensedwhentherefweratorisfkst lbsta//ed,theremaybeak inthewater/inesystem.

Pressthedispenserarmforat /easttwomlbutesto removetrappedairfromthewaterfineandto fi//the

watersystem.Toflushouti_npuritiesinthewater fine,throwawaythefirstslkglassfulsof water

Toaccessice.

Check the back of the refl_Jgerator fin. the specific icemaker kit needed fi)r

VOIII" I/] odel.

Locking the Dispenser

Press the LOCKpad fin" 3 seconds to lock the dispenser and control panel. To mflock, press and hold the pad again fin" 3 seconds.

DoorAlarm

To set the alamo, press the DOORALARM pad. The indicator light will ilhmfinate.

This alam_ will sotmd if either door is open fi)r more than 2 minutes. The

beeping stops when you close the dora;

Cam and cleaning ofthe refrigerator.

Cleaning the Outside

The doorhandles and trim. Clean with a doth

danq)ened with soapy water: Dry with a soft cloth. Do not use wax on the door handles

and trim.

Keep the outside clean. Wipe Mth a clean cloth lightly dampened Mth kitchen

appliance wax or miM liqtfid dish detergent. Dry and polish with a clean,

soft cloth.

Donot w/_)etherefn_?eratorwith a soileddish clothor wet towel. Thesemayleavea residue

that canerodethe paint.Donot usescouring pads,powderedcleaners,bleachorcleaners containingbleachbecausetheseproductscan

scratchand weakenthepaint finish.

Cleaning the Inside

The stainless steel panels and doorhandles.

Stainless steel (on some models) can be cleaned with a commercially a\_lilable

stainless steel cleane_: A spra}_on stainless steel cleaner works best.

Do not use appliance wax or polish on the stainless steel,

Silver-plated plastic parts. Wash parts Mth soap or other mild detexgents. _4_ipe clean

with a sponge, damp cloth or paper to_vl.

Do not scrub with steel-wool pads or other abrasive cleaners.

Tohelp prevent odors,leave an open box of

baking soda in the reflJgerator and ti'eezer

COIlll)_l rtll/e nts,

Unplug the refrigerator before cleaning. If this

is not practical, wring excess moisture out

of sponge or doth when cleaning aromM

switches, lights or controls.

Lrse an appliance wax polish on the inside

sm'tilce between the doo_.

Use wmm water and baking soda solution--

about a tnblespoon (15 ml) of baking soda

to a quart (l liter) _d wateI: This both cleans

and neutralizes odo_. Rinse and wipe dry.

Alter cleaning the door gaskets, apply a

thin laver of petrolemnjelly to the door gaskets at the hinge side, This helps kee I)

the gaskets fl'om sticking and bending out of shape.

Avoid cleaning cud glass shelves with hot water because the extreme temperature difference may cause them to brea£ Handle glass she/yes carefufl_zBumping tempered g/asscan cause

it to shatter

Donot washanyplastic refngeratorpartsin

thedishwashe_

Silver-accented plastic parts. _'_lsl_ parts

with soapy watex: _ipe clean with a sponge,

damp cloth or paper towel.

Do not scrub with steel-wool pads or other abrasive cleane_.

Behind the Refrigerator

Be careful when moving tile refl_Jgerator away fl'om tile wall. _M1t,/pes of floor

coverings can be damaged, pa_licularly cushioned coverings and those with

embossed S/li_lces,

Raise tile leveling legs located at tile bottom fl'ont ot tile refrigerator.

Pull tile refl_Jgerator straight out and return it to position by pushing it straight in.

Preparing for Vacation

g_com

Moving tile refl_Jgerator in a side direction may result in damage to the floor covering

or refrigerator.

I,ower the leveling legs tmtil thev touch tile floo_:

When pushing the refrigerator back, make sure

you don't roll over the power cord or icemaker

supply fine (on some models) and ensure the anti-tli9 bracket is engaged {if equligped).

For long \;l(-ations oi" absen(-es_ i'eil/ove

food and Unl)lug tile refl_Jgei'atoi: Clean tile interior with a baking soda solution of one

tablespoon (15 ml) of baking soda to one quart (1 liter) of water: i,eave the doo_

open.

Set tile icemaker power switch to tile 0 (off) position and shut off tile water supply to

the refl_Jgeratm:

Preparing to Move

Secure all loose items such as base grille, shelves and drawe_ by taping them

securely in place to prevent damage. \_]/en using a hand truck to move tile

refl_Jgerato_; do not rest tile fl'ont or back ot the refl_Jgerator against the hand truck.

This could damage the refl_igerator. Handle only fl'om tile sides of tile refl_igeratm:

If tile temperature can drop below fl'eezing, have a qualified servicer drain the

water supl)ly system (on some models) to

prevent serious property damage due to flooding.

Besurethe refngeratorstaysin anupnght positionduringmoving.

Replacingthe lightbulbs.

Turning the control to the 0 (off) position does not remove power to the light circuit.

Refrigerator Lights

Appearance may vary

_i, CAUTION:ahtb./bsmaybeho_

0 Unplug the refrigerator.

To remove the light shield, grasp the

shield at the back and pull out to release the tabs at the back.

0 Rotate the shield down and then

fi)rward to release the tabs at the fl'ont oI the shield.

Freezer Light

A CAUTION:L/_htb./bsmaybehot

Unplug the refrigerator.

The bulb is located at the top of the

fl'eezer inside a light shield. To remove the shield, grasp the shield at the back

and pull out to release the tabs at the back.

_]b Rotate the shield down and then

fiwward to release the tabs at the front of the shield.

0 _Mter replacing Mth an appliance bulb

of the same or lower wattage, replace

the shield.

0 Plug the refrigerator back in.

NOYE:Appliav, ce bulbs ma_ be ordered fl'om (;E Parts and Accessocies,

800.626.2002.

_Mter replacing with an appliance bulb

of the same or lower wattage, replace

the shield.

0 Plug the refcigerator back in.

Trimkits anddecoratorpanels.

For panel required models

Read these instructionscompletely and carefully.

Before YouBegin

Some models are equipped with trim kits that aflow you to install door panels. Youcan order pre-cut black or white decorator panels from GE Parts and Accessories, 800.626.2002, or you can add wood panels to match your kitchen cabinets.

Panels less than 1/4" (6mm)thick

_,_]_en installing wood panels less than l/4" (6 ram) thick, you need to create a filler panel, such as l/8"

cardboard, that will fit between the face of the door and the wood panel. If you are installing the i)re-cut decorator panels, i)re-cut filler panels are included in the kit. The combined thickness of the decorator

or wood panel and the filler panel should be 11/32" (8.7 ram) with the panel itself being no larger than 1/4" (6 ram).

Panels1/4"tlfickor less

1/4" max

The handle and the top and bottom trim stand in front of the surii_ce of the do()); which requires that the filler be smaller in lenoth_ and width than the panel. Use the gtfidelines beh)w and tape the filler onto the

back of the panel.

Panel

LeftFreshFoodDoor

Filler

Panel-

FreezerDoor

RightFreshFoodDoor

Filler

Panel _ /5

Trimkits anddecoratorpanels.

3/4" (19mm) or Raised Panel

A raised panel design screwed or glued to a ]/4" (6 ram) thick backing, or a 3/4" (]9 ram) routed board

can be used. The raised portion oI the panel must be tid)Hcated to permit clearances oI at least 2" (5.1 cm)

fl'om the handle side fin" fingertip clearance.

Panels thicker than 1/4" (6 ram), up u) 3/4" (19 ram) max., will require that the outer 5/16" (8 ram) oI

panel perimeter be no thicker than 1/4" (6 ram).

Weightlimitationsfor custompanels:

FreshFood10Ibs.(4.5kg)max.for eachdoor FreezerDoor 18Ibs.(8kg)max.

Panelsthickerthan1/4" (6ram)

1/4"(6 IT,e) ThickBacking

16"(8 mm)

1/4" (6lem)max

3/4" (19ram)

Dimensions for Custom Wood Panels

. ..... 1/8"

",I/4" /

(6mr0).... ::_ ........

5/16" (8 mm) minimumat

1/4" (6 ram)

thickness

Top,left and bottoro

Raisedportion of panel

LeftFreshFoodDoor

iiiiiiiiiiiiiiiiiiiii@Ti_Ti_Ti_Ti_Ti_Ti@@i77117iii_!ill

]_i;i_i_i_i_i_i_i_i_ii_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i'ill_iiiiii_

iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii

2"(5.1 cm) Clearance HandleSide

Appearance Panel

2" (51 ram)

minimumat 1/4" (6 ram)

thickness

Handleside

3815/16" (98.9cm)

2"(51 ram)

mlnlmlJ[i-i at

1/4" (6ram/ thickness

Handleside

Raisedportion of panel

(19mm)

Refrigerator Door

RightFreshFoodDoor

5/16"(8 ram) minimumat

1/4" (6mm) thickness

Top,rightand bottom

38 15/16" (98.9cm)

1629/32" (42.9cm)

2" (51 rom)minimuroat 1/4" (6ram)thickness Freezer Door

Handleside

5/16" (8 ram)minimum at 1/4" (6ram)thickness

Left,right and bottomsides Raised

portion ofpanel

771

_ iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii

I_ 1629/32" (42.9cm)

• 'r_ 9529/32-1912cm/ _1-''"',,

1/8" "

..... I .. ..... "':,1/8"

16 "',!_1b_ 1/4)' 1'/4" _t I_!/

" ........ {6taro) (6mm)........ "

,,-" 1/8"

(6mm)......

Installation

Refrigerator

Instructions

Questions? Call 800.GE.CARES (800.432.2737) or Visit our Website at: ge.com

BEFORE YOU BEGIN

Read these instructions completely and carefully.

• IMPORTANT- Save these instructions for

local inspector's use.

• IMPORTANT- Observeallgoverning

codes and ordinances.

• Note to Installer- Be sure to leave these instructions with the Consumer.

• Note to Consumer- Keep these instructions for future reference.

• Skill level- Installation of this appliance requires basic mechanical skills.

• Completion time - Refrigerator Installation

In Canada, call 1.800.561.3344 or Visit our Website at: www.geappliances.ca

MATERIALS YOU MAY NEED (not included)

Lag Bolts Anchor Sleeves

Drill Bit Appropriate for Anchors

For Anti-lip Bracket Mounted on CONCRETEFloors 0nly

TOOLS YOU MAY NEED

20 minutes

Water Line Installation 30 minutes

Adjustable Wrench Ratchet/Driver

Models 21 and 25

3/8" and 5/16" Socket

Anti--[]p Bracket Installation

20 minutes

• Proper installation is the responsibility of the installer.

• Product failure due to improper installation is not covered under the Warranty.

PREPARATION

MOVING THE REFRIGERATOR INDOORS If the refrigerator will not fit through a doorway, the

refrigerator door and freezer drawer can be removed.

• To remove the refrigerator door, see Step 1in the

Reversing the Door Swing section.

• To remove the freezer drawer, see the Removing

the Freezer Drawer section.

WATER SUPPLY TO THE ICEMAKER AND DISPENSER (ON SOME MODELS)

If the refrigerator has an icemaker, it will have to be connected to acold water line. AGE water

supply kit (containing tubing, shutoff valve, fittings and instructions) is available at extra cost from

your dealer, by visiting our Website at ge.com (in Canada at www.geappliances.ca) or from Parts and

Accessories, 800.626.2002 (In Canada 1.888.261.3055).

1/4" Outer Diameter

Compression Nut

and Ferrule (sleeve)

(icemaker models only)

3/32", 1/8" and 1/4"Allen

1/8" Drill Bit and

Electric or Hand Drill

Pencil

Wire Cutters

Phillips Head Screwdriver

wrenches

Tape measure

1/4" Nut Driver

Level

Installation Instructions

INSTALLING THE ANTI-TIP FLOOR BRACKET (on 21 ft. models)

[] LOCATING THE ANTI-TIP

FLOOR BRACKET

Place the anti-tip floor bracket Iocator

[]

Under certain circumstances, this refrigerator

can tip forward,

Injury to persons can result, Install Anti-Tip Bracket packed with this

refrigerator,

[] MEASURE CABINET OPENING

AVAILABLE VS. REFRIGERATOR WIDTH

Measure width of cabinet opening where refrigerator will be placed, W.

Be sure to account for any countertop

overhang, baseboard thickness and any clearance desired. Width, W, should not

be less than 36 inches. The refrigerator

will be placed approximately in the

middle of this opening.

Baseboard Thickness

or Countertop Overhang

(Whichever Is Greater)

Plus Any Desired

Clearance

RH Side

14 I I

REFRIGERATOR

[

Rear Wall

W _:

Front

template (included inside the anti-tip kit) onto the floor up against the rear wall,

within W, and in line with the desired

location of the RH side of the refrigerator (see Figure 1).

Figure 1 - Installation Overview

2 Wall Holes

Bracket on the _s_ RH Side of Locator

Refrigerator / Refrigerator Template Sheet

[] Place the anti-tip floor bracket onto the

Iocator template with its RH floor holes

lined up with the floor holes indicated on the template sheet, approximately 71/4" from the edge of the sheet or the RH side of the refrigerator.

[] Hold down in position and use the anti-tip

floor bracket as a template for marking the holes based upon your configuration and type of construction as shown in Step

3. Mark the hole locations with a pencil,

nail or awl.

NOTE:

• It is REQUIRED to use at least 2 screws to mount the floor bracket (one on each

side of the anti-tip floor bracket). Both must be into either the wall or the floor.

Figure 2 indicates all the acceptable mounting configurations for screws. Identify the screw holes on the anti-tip floor bracket for your configuration.

Installation instructions

[] LOCATING THE ANTI-TIP

FLOOR BRACKET (cont.)

Figure 2 - Acce.ptable Screw

Placement Locations

Preferred Installation -

Minimum Acceptable #1- Minimum Acceptable #2-

Wood

i i

Wall Plate Stud Wood Floor

Minimum Acceptable #3 -

Concrete Floor

Preferred Installation-

Concrete

i i

[] ANTI-TIP BRACKET INSTALLATION

[] WOOD Wall and Floor Construction:

• Drill the appropriate number of 1/8" pilot holes in the center of each floor

bracket hole being used (a nail or awl may be used if a drill is not available)

AND remove the Iocator template from the floor.

• Mount the anti-tip floor bracket by

fastening the 2, or preferably 4, #10-16

hex-head screws tightly into place as illustrated in Figure 3.

Figure 3- Attachment to

Wall and Floor

2 Screws Floor [-1 Wall

RearRH Must Enter Bracket H

Corner of the Wood or X I I

Refrlgerator.._.__ Metal Stud _ "_, H Wall

[] CONCRETE Wall and Floor Construction:

• Anchors required (not provided): 4 each 1/4" x 1 1/2" lag bolts

4 each 1/2" O.D. sleeve anchors

• Drill the recommended size holes for

the anchors into the concrete at the center of the holes marked in Step 2.

• Install the sleeve anchors into the drilled holes. Place the anti-tip floor bracket as

indicated in Step 2. Remove the Iocator

template from the floor.

• Install the lag bolts through the anti-tip

floor bracket and tighten appropriately.

[] WOOD Wall and TILE Floor Construction:

• For this special case, locate the 2 wall holes identified in Fig. 1. Drill an angled 1/8" pilot hole (approx. as shown in Fig. 3) in the center of each hole.

• Mount the anti-tip floor bracket using

the Minimum Acceptable Installation #1,

as illustrated in Fig. 2.

[] POSITIONING THE REFRIGERATOR

TO ENGAGE THE ANTI-TIP FLOOR

AND BASE BRACKETS

[] Before pushing the refrigerator into the

opening, plug the power cord into the receptacle and connect waterline (if equipped). Check for leaks.

[] Locate the refrigerator's RH side and

move back approximately in line with the RH side of the cabinet opening, W. This should position the anti-tip floor bracket to engage the anti-tip base bracket on the refrigerator.

[] Gently roll the refrigerator back into

the cabinet opening until it comes to a complete stop. Check to see if the refrigerator front lines up with the cabinet front face. If not, carefully rock the refrigerator forward and backward until engagement occurs and you notice that the refrigerator is fully pushed up against the rear wall.

[] OPTIONAL: Adjust the rear (and front)

wheel height settings to fully engage the rear anti-tip brackets, while also aligning the refrigerator front with the cabinet

front face.

NOTE:

If you pull the refrigerator out and away from the wall for any reason, make sure the anti-tip floor bracket is engaged when the refrigerator

is pushed back against the rear wall.

Installation Instructions

INSTALLING THE REFRIGERATOR

REFRIGERATOR LOCATION

• Do not install the refrigerator where the temperature will go below 60°F (16°C) because it

will not run often enough to maintain proper temperatures.

• Do not install the refrigerator where the temperature will go above IO0°F (37°C) because it

will not perform properly.

• Install it on a floor strong enough to support it fully

loaded.

CLEARANCES

Allow the following clearances for ease of installation, proper air circulation and plumbing and electrical

connections.

Standard Depth Counter Depth Models Models

Sides 1/8" (3 mm) 1/8" (3 mm) Top 1" (25 mm) 1" (25 mm) Back 1" (25 mm) 1/2" (13 mm)

REMOVE TOP CAP (cont.)(onsomemodels)

REINSTALL DOORS, DRAWERS AND TOP CAP

[] Carefully lower the door onto the center hinge.

Reinstall top hinge. NOTE: Ensure the door is properly aligned to the case top to avoid readjustment of the door during top cap

reinstallation.

[] Place cap over the top of the refrigerator. Reinstall

the original screws in the top and back of the cap.

[] Reinstall the bottom freezer drawer. Refer to

"Replacing the Freezer Drawer" section.

REMOVE TOP CAP (onsomemodels)

• IMPORTANT NOTE: This refrigerator is34-1/2" deep. Doors and passageways leading to the installation

location must be at least 36" wide in order to leave the doors and handles attached to the

refrigerator while transporting it into the installation location. If passageways are lessthan 36",the

refrigerator doors and handles can easily be scratched

and damaged. The top cap and doors can be removed to allow the refrigerator to be safely moved indoors. Start with Step A.

• If it isnot necessary to remove doors, skip Step A. Leave tape and all packaging on doors until the

refrigerator is inthe final location.

• SKID REMOVAL: _lt refrigerator to each side to remove skid.

• NOTE: Use a padded hand truck to move this refrigerator. Place the refrigerator on the hand

truck with a side against the truck. We strongly

recommend that TWO PEOPLE move and complete

this installation.

[] Locate and remove the two Phillips head screws

on the top of the refrigerator. Remove the two screws on each side at the rear of the top cap.

Lift off and remove top cap.

[] Remove the fresh-food door. Refer to Steps 1

through 3 of "Reversing the Door Swing" section.

[] Remove the bottom freezer drawer. Refer to

"Removing Freezer Drawer" section.

[] Move refrigerator to the installation location.

TopHingeB

[] CONNECTING THE REFRIGERATOR

TO THE HOUSE WATER LINE

(icemaker and dispenser models)

A cold water supply is required for automatic icemaker operation. If there is not a cold water

supply, you will need to provide one. See Installing the Water Line section.

NOTES:

• Before making the connection to the refrigerator, be sure the refrigerator power cord

is not plugged into the wall outlet.

• If your refrigerator does not have a water filter,

we recommend installing one if your water

supply has sand or particles that could clog the screen of the refrigerator's water valve. Install it

in the water line near the refrigerator. If using GE SmartConnect TM Refrigerator Tubing Kit, you

will need an additional tube (WXO8XIO002) to

connect the filter. Do not cut plastic tube to install filter.

Installation Instructions

[] CONNECTING THE REFRIGERATOR

TO THE HOUSE WATER LINE

(cont.)

[] If you are using copper tubing, place a

compression nut and ferrule (sleeve) onto

the end of the tubing coming from the

house cold water supply.

If you are using the GE SmartConnect TM tubing, the nuts are already assembled to the tubing.

[] If you are using copper tubing, insert

the end of the tubing into the refrigerator

connection, at the back of the refrigerator,

as far as possible. While holding the tubing, tighten the fitting.

If you are using GE SmartConnect TM

tubing, insert the molded end of the tubing into the refrigerator connection,

at the back of the refrigerator, and tighten the compression nut until it is hand tight.

Then tighten one additional turn with a wrench. Overtightening may cause leaks.

[] Fasten the tubing into the clamp provided

to hold it in position. You may need to pry

open the clamp.

[] TURN ON THE WATER SUPPLY

(icemaker and dispenser models)

Turn the water on at the shutoff valve (house water supply) and check for any leaks.

[] PLUG IN THE REFRIGERATOR

On models with an icemaker, before plugging in the refrigerator, make sure the icemaker power switch is set to the O (off) position.

See the grounding information attached to the power cord.

One of the illustrations below will look like the connection on your refrigerator.

Icemaker-Ready models

1/4" Copper

Tubing ///1

1/_lamp _'_t_

Compression

Nut _ Ferrule _

(sleeve) _k-'_

Refrigerator /_4 Connection /

Icemaker-lnstalled Models

Ferrule 1/4"

Refrigerator (sleeve) Compression

Connection --

Tubin£

_ Tubing

SmartConnect TM Tubing

1/4" Tubing

Tubing Clamp

[] PUT THE REFRIGERATORIN PLACE

Move the refrigerator to its final location. Make sure the back side of the refrigerator engages the anti-tip bracket properly. The anti-tip floor bracket should line up with the cutout in the back bottom of the refrigerator, and fit through the cutout when the refrigerator is pushed into position. (Refer to page 18, Step 2A for more information.)

[] LEVEL THE REFRIGERATOR

Turn the front roller adjusting screws clockwise to raise the refrigerator,

counterclockwise to lower it. Use a 3/8" hex wrench with extension, or an Roller adjusting screws

adjustable wrench. To adjust the rollers on 21' Counter Depth models: These models also have rear adjustable rollers

so you can align the refrigerator with your kitchen cabinets. Use a 3/8" hex wrench with extension to turn the screws for the rear rollers--

clockwise to raise the refrigerator, counterclockwise to lower it.

Installation Instructions

INSTALLING THE REFRIGERATOR (cont.)

[] REMOVE THE FRESH FOOD

DOOR HANDLE

(For placement in the installation location or reversal of the handles - on some models

Stainless steel (on some models):

@ REMOVING

THE DOOR

HANDLE: Loosen the set screws with the 3/32" Allen wrench

and remove Badge the handle. NOTE:

For Double Door

models follow the same procedure on the opposite

door.

Mounting Fasteners

(appearance may vary)

Plastic handle (on some models):

@ REMOVING THE DOOR HANDLE: Depress the

tab on the underside of the handle and slide the handle up and off of the mounting

fasteners.

O REVERSING

THE DOOR

[] REMOVE THE FREEZER DOOR

HANDLE

Stainless steel and plastic handles:

@ Loosen the set screws located on the underside

of the handle with the 1/8"Allen wrench and

remove the handle.

NOTE: If the handle mounting fasteners need to

be tightened or removed use a 1/4" Allen wrench.

some models):

* Remove

the handle mounting

fasteners with a 1/4" Allen wrench and transfer the

handle Mounting mounting

fasteners to the right side. (appearance may vary)

" Remove the

logo badge.

, Remove and transfer the plug button to

the left side of the fresh food door. NOTE:

Use a flat plastic edge to prevent damaging the door. Remove any adhesive on the door with a mild detergent. Remove the paper covering on the adhesive backing on the logo badge prior to carefully attaching the badge

to the door.

Fasteners.

Installation Instructions

[] ATTACH THE FRESH FOOD

DOOR HANDLE

Stainless steel handle:

Attach the handle to the handle

mounting

fasteners and tighten the set

screws with a 3/32" Allen

wrench. Mounting NOTE: For Double Fasteners

Door models

follow the same

procedure on the

opposite door.

(appearance may vary)

Plastic handle:

Q Attach the handle to the handle mounting

fasteners by aligning the slots with the handle

mounting fasteners.

O Slide it down until it is firmly locked into

position.

[] ATTACH THE FREEZER DOOR

HANDLE

Stainless steel and plastic handles:

Q Attach the handle firmly to the mounting

fasteners and tighten the set screws on the

bottom of the handle with a 1/8" Allen wrench.

(appearance may vary)

Slots on back U of handle

(appearance may vary)

Mounting

fasteners

Installation Instructions

INSTALLING THE REFRIGERATOR (cont,)

I_] LEVEL THE REFRIGERATOR

The leveling legs have 2 purposes:

1) Leveling legs adjust so the refrigerator

is firmly positioned on the floor and

does not wobble.

2) Leveling legs serve as a stabilizing brake to hold the refrigerator securely in position during operation and

cleaning. The leveling legs also prevent the refrigerator from tipping.

[] Remove the grille by removing the two

Phillips head screws.

[] Turn the leveling legs clockwise to raise the

refrigerator, counterclockwise to lower it.

[] SET THE CONTROLS

Set the controls to the recommended setting.

he]

0 "FIS RECOMMENDED 37'F ISRECOMMENDED

REMOVE PACKAGING

[]

PlrJ

START ICEMAKER

(icemaker models) A) Remove all tape, foam and protective

packing from shelves and drawers.

B) Remove the tie downs from the freezer

baskets.

C) Place half width basket onto drawer

slides. See About the freezer section for instructions.

Set the icemaker power switch to the I (on) position. The icemaker will not begin to operate until it reaches its operating temperature of 15°F (-9°C) or below. It will then begin operation automatically. It will take 2-3 days to

fill the ice bin.

CAUTION: Toavoidpossible

personal injury or property damage, the leveling legs must be firmly touching

the floor.

[] Replace the base grille by inserting the two

Phillips head screws.

NOTE: In lower water pressure conditions, the

water valve may turn on up to 3 times to deliver enough water to the icemaker.

Installation Instructions

REMOVING THE FREEZER DRAWER (on some models)

The freezer drawer can be removed, if needed,

to fit through tight areas.

Read these instructions completely and carefully.

[] REMOVE THE BASKET

[] Open the freezer drawer until it stops. [] Cut the 2 wire ties off of the basket with

wire cutters.

[] The freezer basket rests inside 4 tabs on

the freezer slides. Lift the basket up and

out of the 4 tabs.

[] Tilt the front up and lift the entire basket

up and out of the drawer.

\\\\\\\\\

[] REMOVE THE BASE GRILLE

(if needed)

If, after removing the freezer drawer and refrigerator door, the refrigerator will still not fit through a doorway, the base grille

can be removed.

[] Remove the base grille by removing the

2 Phillips head screws.

[] REMOVE THE DRAWER FRONT

FROM THE SLIDES

[] Remove the 10 hex head screws from the

door and remove the door.

Q DO NOT remove the torx screws

from the rail assemblies.

DO NOT remove

torx screws

Rail Assembly

[] Set the drawer front non-scratching

surface.

[] Push the rail assemblies back into the

cabinet.

on a

Installation Instructions

REPLACING THE FREEZER DRAWER (on some models)

o Two people may be required to complete

this procedure.

[] ATTACH AND SECURE THE

DRAWER FRONT TO THE SLIDES

[] Pull out the rail assemblies to the full

length on each side of the cabinet.

[] Drive the top screw into the door on each

side until it is 1/2 way in.

[] ATTACH AND SECURE THE

DRAWER FRONT TO THE SLIDES

(CONT.)

[] Drive screws fully. (There are 10 screws.)

Screw

Step D2: I J Drive

fully•

[] Hang the drawer front onto open slots on

the slides.

•Slot

Step D3:

Drive screws in these holes.

-- Step DI: Line up

screw

hole in

freezer drawer and drive

fully.

[] REPLACE THE FREEZER BASKET

Replace the lower freezer basket by lowering it into the frame.

\\\\

Installation Instructions

REVERSING THE DOOR SWING (Single Door Refrigerator Models only)

IMPORTANT NOTES

When reversing the door swing: NOTE: Door swing is not reversible on stainless

steel models. * Read the instructions all the way through

before starting.

* Parts are included in the door hinge kit.

• Handle parts carefully to avoid scratching

paint.

• Set screws down by their related parts to avoid using them in the wrong places.

• Provide a non-scratching work surface for

the doors.

IMPORTANT: Once you begin, do not move the cabinet until door-swing reversal is completed.

These instructions are for changing the hinges from the right side to the left sideiif you ever want to change the hinges back to the right side,

follow these same instructions and reverse all references to left and right.

• Once door swing is finalized, ensure

the logo badge is properly aligned and

permanently secured to the door by removing

the adhesive cover on the back side,

NOTE: A replacement logo badge is included in the hinge kit.

Unplug the refrigerator from its electrical outlet. Empty all door shelves, including the dairy

compartment.

[] REMOVE THE

REFRIGERATOR DOOR

[] Tape the door shut with masking tape.

[] Remove the hinge cover on top of the

refrigerator door by removing the Phillips head screws and pulling it up,

[] Using a 5/16" socket ratchet/driver,

remove the bolts securing the top hinge to the cabinet. Then lift the hinge straight up to free the hinge pin from the socket in the top of the door.

-linge Cover

TOOLS YOU WILL NEED

Adjustable Wrench

Masking Tape

Phillips Screwdriver

Thin-blade Screwdriver

5/16" Socket

Ratchet!Driver

Torx T-20 Driver

i G

[]

Remove the tape and tilt the door away from the cabinet. Lift the door off the

center hinge pin. Ensure that the plastic hinge pin thimble remains on the hinge pin or inside door hinge pin hole located in the

bottom of the door.

[] Set the door on a non-scratching surface

with the inside up.

Hinge

Installation Instructions

REVERSING THE DOOR SWING (cont.)

[] REMOVE CENTER HINGE

Using a 5/16" socket ratchet/driver, remove the bolts securing the center hinge to the cabinet. Set the hinge

and bolts aside.

[] INSTALL CENTER HINGE

[] Transfer the plug button and screw hole

cover in the hinge holes on the left side to

the right side.

TRANSFER REFRIGERATOR

[]

DOOR STOP

[]

Remove the door stop on right side of

the bottom of the refrigerator door by

removing the two screws.

[]

Move the plastic hinge hole thimble to the opposite hole.

[]

Install the door stop on the left side, making sure to line up the screw holes in the door stop with the holes in the

bottom of the door.

Bottom of Bottom of

Refrigerator Door Refrigerator Door

(Right Side) (Left Side)

[] Install the center hinge from the kit on the

left side.

NOTE: A new hinge will be required for the left side (supplied in the door hinge kit).

ITI TRANSFER REFRIGERATOR

DOOR HANDLE TO RIGHT

Refer to Remove the Fresh Food Door Handle and Attach the Fresh Food Door Handle sections for instructions.

Installation Instructions

[] REHANG REFRIGERATOR DOOR

[] Lower the refrigerator door onto the

center hinge pin. Ensure that the plastic hinge pin thimble is on the center hinge pin or inside door hinge pin hole located

in the bottom of the door.

[]

Insert the top hinge pin into the hinge hole on top of the refrigerator door. Make sure the door is aligned with the cabinet. Attach the hinge to the top of the cabinet

loosely with the bolts.

[]

Make sure the gasket on the door is flush against the cabinet and is not folded. Support the door on the handle side and

make sure the door is straight and the gap

between the doors is even across the front. While holding the door in place,

tighten the top hinge bolts. Replace the

hinge cover.

[] INSTALL THE LOGO BADGE

Remove the adhesive backing paper and align the pins on the back of the badge with the holes in the door. Apply pressure to the badge to ensure it sticks

to the door.

Installation Instructions

REMOVING THE DOORS (Double Door Refrigerator Models only)

IMPORTANT NOTES

NOTE: Door swing is not reversible.

• Read the instructions all the way through before starting.

• Handle parts carefully to avoid scratching paint.

• Set screws down by their related parts to avoid using them in the wrong places.

• Provide a non-scratching work surface for

the doors.

IMPORTANT: Once you begin, do not move the cabinet.

These instructions are for removing the doors.

Unplug the refrigerator from its electrical outlet.

Empty all door shelves, including the dairy compartment.

TOOLS YOU WILL NEED

[] REMOVE THE

REFRIGERATOR DOORS

[] Tape the doors shut with masking tape.

(for water dispenser models)

[] Start with right-hand door first: Remove

the screw securing the center hinge cover, lift the hinge cover and place to the side on top of the refrigerator.

aemo__

Adjustable Wrench 3/8" and 10 mm Socket

Masking Tape

Phillips Screwdriver

Ratchet/Driver

Thin-blade Screwdriver

(for water dispenser models)

[] Remove water coupling and power

coupling.

Water Coupling o

Remove the metal spring _

clip. Use a screwdriver to _ ..... -

push the red plastic locking "_ /

clip down and off. _" I __

Power Coupling

Black mark

flush with collar assembly

Pull apart power

coupling to disconnect

+ 180 hidden pages