GE PFSF5NJWAWW, PFSF5NJWACC, PFSF5NJWABB, PFIC1NFWCWV, PFIC1NFWCBV Owner’s Manual

...
ge.com
Safety Instructions ........... 2, 3
Operating Instru_tions
Additional Features ............. S
Automatic Icemaker ........... 11
Care and Cleaning .......... 12-13
Controls .................... 4-5
Crispers and Pans .............. 9
Freezer ...................... 10
Repl acing the i,igh t Bulbs ....... 14
_'ater Filter . .................. 6
Installation InsTtructions
Installing the Anti-Tip
Floor Bracket .............. 18-19
Installing the Refrigerator .... 20-24
Installing the _'ater Line ..... 33-35
Preparing to Install
the Refligeratnr . .............. 17
Removing and Replacing the
Freezer Drawer . ........... 25, 26
Reversing the Door Swing
(Single Door Refrigerator
Models only) .............. 27-29
Removing and Replacing the Doors (Double Door
Refrigerator Models only) .... 30-32
Trim Kits and Decorator
Panels .................... 15-16
Models21 and25
Cong_lateur inf&ieur
R frig rateurs
La section fran_aise commence a la page 49
Congelador inferior
Refrigeradores
La secci6n en espa#ol empieza en /a pagina 93
Troubleshooting Tips ....... 36-40
Normal Operating Sounds ...... 36
Consumer Support
Consumer Support ..... Back Cover
Performance Data Sheet ........ 47
Product Registration
for Canadian Customers ..... 43, 44
Product Registration
fox U.S. Customers ......... 41,42
State of California ¼'ater
Treatment Device Certificate ..... 48
¼'arranty fox Canadian
Customers ................... 46
V(arranty fox U.S. Customers ..... 45
Writethe modelandserial numbershere:
Model # Serial #
Find these numbex_ on a label on the right side, near the top of
the refrigerator compartment.
200D9366PO01 49-60489-2 06-07JR
iMPORTANTSAFETYiNFORMATiON. READALLiNSTRUCTiONSBEFOREUSING.
WARNING!
Use this appliance only for its intended purpose as described in this Owner's Manual.
SAFETYPRECAUTIONS
When using electrical appliances, basic safety precautions should be followed, including the following:
_:i:This refl-Jgerator must be properl_ installed
and located in accordance with the Installation Instructions before it is used.
i)::Do not allow children to climb, stand or hang
on the shelves in the refl'igeratm: They could damage the refi_igerator and seriously injm'e
themselves.
::_Do not touch the cold sm'fi_ces in the fl'eezer
compartment when hands are damp or wet. Skin mm stick to these extremely cold stmfi_ces.
i?<Do not store or use gasoline or other flammable
vap(n_ and liquids in the vMnitv of this or anv other appliance.
i)::Keep finge_ out (ff the "pinch point" areas;
clearances between the do(n_ and between the (loo_ and cabinet are necessarily small.
Be careful closing (lores when children are in the area.
i(i'In refl_igeratm5 Mth automatic icemake_s,
avoid contact with tile moving parts (ff tile
ejector mechanism, or with tile heating element that releases tile cubes. Do not place finge_ or hands on tile automatic icemaking mechanism
while tile refl_igerator is plugged in.
i!:i'Unplug tile reliigerator before cleaning and
making repai_.
NOTE: Westronglyrecommendthatany servicingbe
performedby aquafified individual
i(i,Setting either or both controls to 0 (off) does
not I'ell/OVe power to tile light (-iI'('tlit.
i::tDo not refl'eeze frozen fi)ods which have
thawed complemly.
DANGER!RISKOFCHILDENTRAPMENT
PROPERDISPOSALOFTHEREFRIGERATOR
Refrigerants
of tile past.Junked or abandoned refl_igerat(n_ are Child entrapnlent and suffocation are not problems
still dangerous...exert if they will sit for 'ijust a few daxs." If _ou are getting rid of _om" old refri(*erat(m
please follow tile instructions below to help prevent accidents.
Before YouThrew Away YourOldRefrigerator
All refl'igeration products contain refl'igerants, which tinder federal law InUSt be relnoved prior
to product disposal. If you are getting rid of an old refl'igeration product, check with tile
company handling tile disposal about what
to do.
or Freezer:
iJi::_ke off tile dome.
iJi::i,eaxe tile shelves in place so that children may
not easiE climb inside.
USEOFEXTENSIONCORDS
Because of potential safety hazards under certain conditions, we strongly recommend against the use of an extension cord.
However; if you must use an extension cord, it is absolutelx necessary that it be a UiTlisted (in tile United States) or a CSA certified (in Canada),. -_are ,gr°tmding, t_,])e appliance extension cord having a grotmding
2
t)])e I)lu(*_and outlet and that the electrical rating of the cord be 15 amperes (minimum) and 120 xolts.
WARNING!
HOWTOCONNECTELECTRICITY
Donot, under any circumstances, cut or remove the third (ground) prong from the power cord.
For personal safety, this appliance must beproperly grounded.
ge.com
The power cord of this appliance is equipped
with a 3-prong (grounding) plug which mates with a standard 3-pr(mg (grounding) wall outlet to
minimize the possibiliQ, of electric shock hazard fl'om this appliance.
Have the wall outlet and circuit checked by a qualified electridan to make sure the outlet is
properly grounded.
Where a standard 2-prong wall outlet is
encountered, it is your personal responsibiliQ' and obligation to have it replaced with a properly
grounded 3-prong wall outlet. The reli-igerator should alwa D be plugged into its
own individual electrical outlet which has a voltage rating that matches the rating plate.
This provides the best pe_om_ance and also I)rexents oxerloading, house wiring circuits which
could cause a fire hazard fl'om oxerheated wires.
Never unplug your refrigerator bv pulling on the power cord. Mways grip plug firefly and pull
straight out fl'om the outlet.
Repair or replace immediately all power cords that have become fl'ayed or othe_Mse damaged. Do not
use a cord that sho_:s cracks or abrasion damage along its length or at either end.
\,_]_en moving the refrigerator away fl'om the wall, be careflll not to roll over or damage the power cord.
READANDFOLLOWTHISSAFETYINFORMATIONCAREFULLY.
SAVETHESEINSTRUCTIONS
Aboutthe controlswith temperaturesettings.
(onsomemodels)
[]
[]
[] []
Hold 3 seconds to _eset NoEd 3 seconds
WARMER _ _WARMER
COLDER COLDER
0oF Recommencled 37- F Recommended
TEMPERATURE SET
[]
(onsomemodels)
NOTE: Therefrigeratoris shipped with protective film coveringthe temperaturecontrols. If this film was not removedduringinstallation, removeit now
Thetemperature controls are preset in the factory at 37°F for the refrigerator compartment
and O°Ffor the freezer compartment. Allow 24hours for the temperature to stabilize to the
preset recommended settings.
Thetemperature controls can display both the SET temperature as well as the actual temperature in the refrigerator and freezer. The actual temperature may vary slightly from the SETtemperature based on usage and operating environment.
Setting either or both controls to OFFstops cooling in both the freezer and refrigerator compartments, but does not shut off electrical power to the refrigerator.
Changingthe Temperature
For Controls-on-the-DoorModels:
To change the temperature, press and release the WARMER or COLDER pad. The ACTUAL TEMPlight
will c(nne on and the display will show the actual temi)eratm'e. To change the temperature, tap
either the WARMERor COLDERpad tmtil the desired temperature is displayed.
For ControlsInside the Refrigerator:
Opening the door displa):s the actual temperature. To change the temperature, press either the
WARMER or COLDER touch pads tmtil the
desired temperature is displayed.
Once the desired temperature has been set, the temperatm'e display will return to the actual
4
i'efi-Jgei'ator and fl'eezer teil/perattlres aftei" .5 seconds. Several ac!iustments may be required.
Each time )ou ac!iust controls, allow 24 horns fin" the refrigerator to reach the temperature you haxe set.
To turn the cooling system off, trip the WARMER pad
fro" either the refl_igerator or the fl'eezer tmtil the display shows OFF. To turn the unit back on, press the
COLDER pad for either the refl_igerator or fl'eeze_:
Then press the COLDER pad again and it will go to the preset points of O°Ffi)rthe fl'eezer and 37°Ffi)r
the refi_igeratox: Setting either or both controls to Off stops cooling in both the fl'eezer and
refl_igerator compartments, but does not shut off electrical power to the refi_igeratm:
About TurboCooEM(onsome models) ge.oom
Turbo €O01
(onsomemodels)
(on some models)
How it Works
TurboCool rapidly cools the retiigerator
colnl)artinexlt ixl order to inore quickly cool fi)o(ls. Use TurboCool when adding a
large anlount of toed to the refligerator comi)artn/ent, putting away fi)ods after they
have been sitting ()tit at i'OOlll temperature or when putting away waml letterers. It can
also be used if the refiigerator has been
without power for an extended period.
Once acti\:_md, the compressor will turn oil immediateh and the rims will cycle on and off at high speed as needed for eight hom_.
The compressor will continue to mn tmtil the refi_igerator compartment cools to
approximately 34°F (1 °C), then it will cvcle on and off to maintain this setting. ?dter 8
hom_, or if TurboCool is pressed again, the refl_igerator compa rtm ent will return to
the original setting.
About Door Alarm (onsomemodels)
The door alaml will somld if any
dooI" is open _()I" I//oI'e [l/}lI1 2 IlllIltlte,_,
The beei)im,_ stops when you, close
the door,
How to Use
Press TurboCool.The retiigerator temperature display will show ccc.
_Mter TurboCoolis complete, the
refl_igerator compartment will retm'n to the original setting.
NOTES:The refrigerator temperatm'e
cmmot be changed dining
rurboCooL
The fl'eezer temperature is not affected during TurboCool.
When opening rite refrigerator
door during TurboCool,the fires
will continue to mn if they have
cycled on.
(onsomemodels)
_ ii _ i I i i ii_ i
(. ALA..DOORli ¸
iiiii iii _ii
on somemodels)
(onsomemodels)
About Energy Saver (onsomemodels)
This product is equipped with an Energy/
Saver featm'e. The refl_gerator is shil)ped
with the Energy' Saver teatm'e enabled.
Over time, moisture can timn on the fl'ont surli_ce of tile refl_igerator cabinet and cause i'tlSt. If moistm'e does appear on the
front surfi_ce of the refligemtor cabinet,
tm'n off the Energy Saver ti_atm'e by pressing and releasing the ENERGY SAI/ER
pad on the control panel.
(onsomemodels)
Aboutthe water filter.(onsomemodels)
Water Filter Cartridge
The water filter c;u_fidge is located in the back upper fight corner of the refi'igerator
COl//pll 1"_1//ellt.
When to Replace the Filter
There is a replarement indicator light tbr tile water filter ca_qh-idge on the
temperature display. This light will turn
(mmge to tell you that you need to replace
the filter soon. The filter cam-idge should be replaced when the replacement
indicator light ttlrns red or if tile flow
of water to tile dispenser or icemaker decreases.
Installing the Filter Cartridge
0 If you are replacing the cartridge,
first rem_we tile old one. Open the cariridge cover by pressing ill on tile tab at tile fi'ont and pulling down.
0 Remove tile cartridge b} sloxd} rotadng
it counter clocBvise. A small amount of water may drip down.
Filter Bypass Plug
_i_u must use tile filter b}pass plug when a
replacement filter camJdge is not available. Tile icemaker will not operate without tile
filter or filter b}])ass plug.
Replacement Filters:
To order additional filter cartridges
in the United States, visit our Webs#e, re.corn, or carl GE Parts and Accessories,
800.628.2002.
Filter Model (;S\'_TF
(Mstome_s in Canada shoukl consult the } ellow pages for tile nearest Mabe
Service Centre:
Water Filter
Hold 3 Secs
(on some models)
Z m
I RESET1/7
FILTER J
Hold 3 SecondstO reset
(on some models)
CAUTION: been
/nthesystem,thefi/tercartridgemaybeejectedas it/s removed.Usecautionwhenremoving
0 Remo_e the protecti_ e foil from tile
end of tile camJdge.
I,ining up tile arrow on tile calqhidge and the ca_qtfidge holder; slowly rotate
the cartridge clockwise until it stops. \_l_en tile ca_fidge is properly
installed, yon will ieel it "click" as it locks into place. The grip on the end
ot tile cartridge sb.ould be positioned _w_icallv. Do notovertighten.
0 (lose tile camidge co\w:
0 I_,tm water fi'om tile dispenser for
3 minutes (about l/2 gallons) to clear the system and pre\vnt sputtering.
See ToUsetheDispensersection.
Press and hokl the RESETWATERFILTER pad ibr 3 seconds.
NOTE"A newly-installed water filter cartridge
may cause water to spurt ti'om tile dispense_:
Abouttheshelvesandbins. gecem
Not all features are on all models.
Rearranging the Shelves
Shel',es in the refl_igerator c()ml)artn_ent are a(!justable.
Refrigerator Compartment
To remove:
0 ]_emo_e all items fl'om the shelf.
O Tilt the shelf up at the fl'ont.
O I,ifi the shelf III) at the back and
Some models have wire shelves that can be adjusted in the same mam?er.
bring the shelf out.
To replace:
_qfile tilting the shelf I/I), insert the top
hook at the back of the shelf ill a slot on the track.
@ I,ower the fl'ont of tile shelf until the
bottom of the shelf locks into place,
i 0
Spillproof Shelves (onsomemodels)
SI)illproof shelves have special edges to hel I) I)revent spills fl'oln dI'iI)ping to lower
shelves. To relnove or replace the shelves, see Rearranging the Shelves,
Slide-Out Spillproof Sheff (onsomemodels)
The slide-out si)illproof shelf allo_v_ you to reach itelns stored behind othei_. The
spedal edges are designed to hel I) prevent
spills fl'om dripping to lower shelves.
Toremove:
Remove all items ti'om shel£
0 Slide the shelf otlt iintil it stops.
Lift the fi'ont edge of the shelf until the central tabs are above the fl'ont hal:
O (_ontinue i)ulling the shelf t0rward
until it can be relnoved.
Toreplace:
Place the rear shelf tabs just in fl'ont of the central notches on the shelf fl'ame.
Slide the shelf ill until the central tabs are slightly behind the fl'ont bin;
O i,ower the shelf into place until it is
hoi-izontal and slide the shelf ill.
Makesurethattheshelfsitsflatafterre/bsta//ation anddoem'tmovefreelyfromsidetoside.
Makesureyoupushtheshelvesa//thewayin beforeyoudosethedoor
7
Abouttheshelvesandbins.
Adjustable Bins on the Door
Ac!iustable bins can easily be carx_ied ti'()m
I'eti_igeI'_l[oI" 1o w()x'k _lI'e_l,
To remove: I,ifi bin straight up, then
pull out.
To replace or relocate: Slide in the bin j ust
above the molded door supports, and push down. The bin will lock in place.
Non-Adjustable Bins on the Door
To remove: Lift the bin straight ui), then
pull out.
To replace: Engage the bin in the molded
supports on the door and push do_n.
It will lock in place.
Abouttheadditional features.
The snuggerhelps prevent tipping, spilling
or sliding of small items stored on the door shelf. (h_iI) the finger hold near the rear of the snugger and move it to fit w)ur needs.
Not all features are on all models.
Non-Adjustable Beverage Rack
To remove: Lift the rack straight up, then
ptfll out.
To replace:Engage the rack in the molded
SUl_l_orts on the door and push down.
It will lock in place.
8
Aboutthe crispersandpans. gecem
Not all features are on all models.
Fruit and Vegetable Crisper
Excess water that mm accunmlate in the bottom of the (h'awe_ or under the (h'awe_
should be wiped dry;
Adjustable Humidity Crisper (onsomemodels)
Slide the control all the way to the Slide the control all the wax to the LOW
HIGHsetting to proxide high humidit_ ,settino-_to proxide lower humidi_' lmels recommended for most xegetables, recomm ended fiw most fl'uits.
Adjustable Temperature Deft Pan (onsomemodels)
Slide the control all the way to the left for
the coldest temperature.
How to Remove and Replace the Deft Pan
Toremove:
0 Remoxe the ti'uit and xegetable (h'awei_. @Pull the drawer ()tit to the stop position.
'ingLocks 0 I,ifl the lid to access the 4 swing locl_s.
Rotate all fimr ,sxdn,*_locks to the unlock position.
0 Lilt the fl'ont of the drawer up and ()tit.
Toreplace:
Make sure all tour swing locks are in the
unlock position.
@ Place the sides of the drawer into the
drawer supports, making sure the swing
locks fit on the drawer slots.
I,ock all fimr swing locks by rotating
them to the lock position.
0 i,ower the lid and slide in the drawer
Replace the fl'uit and xegetable (h'awei_.
J J
Aboutthe freezer.
Not all features are on all models.
Freezer Shelves and Baskets
O A shelf abo\v the ice storage bin
Appearance and features may vary
Basket Removal
To remove the deep full-width basket on
freezer drawer models:
O Open the fl'eezer drawer until it stops.
O The fl'eezer basket rests on the inside
_]b Lift the basket so that all 4 tnbs are out
Appearance may vary
v
A haltZwidth basket A shallow filll-width basket
A deep flfll-width basket
tnbs on the drawer slides.
of the slide bracket.
Tilt the basket and lift out of the
drawer,
When replacing the deep full-width basket
Tilt the basket back and lower it down
into the drawe_: Rotnte the basket to a horizontnl position and press it down into
the 4 aligmnent tabs,
NOTE:M_m_sbe sm'e that all 4 basket tnbs
are engaged in the slide brackets befl)re sliding back into the fl'eezet:
Appearance may vary
0 Make sm'e the plastic sleexes remain
attached to the 4 tnbs on the slide
brackets.
/
To remove the half-width basket:
Ptfll the basket out to the stop location.
Lift the basket up at the fl'ont to release it from the slides,
0 Lift the back up and out of the slide.
)
When replacing the basket, make sure that
the wire tnbs and wire hooks on the sides oI the basket go into the slots in the top
ot the uI)per basket slides.
NOTE:Mw'a_:sbe sure to flfllv close this
basket.
Toremove the shallow full-width basket:
Ptfll the basket out to the stop location.
Lift the ti'ont up and oxer the stop location.
0 Lift the basket up and out.
Appearance may vary
lO
Abouttheautomaticicemaker, ge.cem
A newly installed refrigerator may take 12to 24 hours to begin making ice.
Power Automatic Icemaker (on some models) Switch
Green
PowerLight
Icemaker
The icemaker will produce seven cubes per cycle---al)l)roxin_ately 100-130 cubes in a 24-hour period, del)ending on fl'eezer
coi/lpai'tlllent tei/lpei'attli'e_ i'ooi/1
temperature, nmnber of door openings and other use conditions.
See below flit how to access ice and reach the power switch.
If the refl_Jgerator is operated befin'e the
water c(mnecfion is made to the icemake_, set the power switch in the 0 (off) position.
When the refl_Jgerator has been connected
to the water SUl)l)ly, set the power switch to the I (on)position. The icemaker power
light will turn green when the fl'eezer light switch is pressed in or when the fl'eezer
door is ch)sed.
The icemaker Mll fill Mth water when it
cools to 15°F (-10°C), A newly installed reflJgeratof Ill}IV take ] 2 to 24 hotlI'S to
begin making ice cubes.
You xfill hear a buzzing sotmd each dine
the icemaker fills with water:
Throw awax the first tew batches of ice to allow the water line to clea_:
Be sm'e nothing interteres with the sweep of the teeler amL
When the bin fills to the level of the teeler
am_, the icemaker will stop produdng ice. It is nomml fin" several cubes to be
joined together:
If ice is not used fl'equenfly, old ice cubes
will become ch)udy, taste stale and shrink.
NOTE."Inhomeswith lower-than-averagewater pressure,you mayhear the icemakercycle multiple times whenmaklbg onebatch of ice.
NOTE,"Setthepowerswitchtothe0 (off)position
if the watersupplyisshutoff.
Shelf
Toroach the power switch.
r
i!iii_i
DispenserCradle
SpillShelf
Accessing Ice and Reaching the Power Switch
To reach the icemaker power switch, pull the
shelf al)oxe the ice bin straight ()tit. _Mways be sm'e to replace the shelf.
Toaccess ice, simpl) pull the bin fi)rward.
Icemaker Accessory Kit
If )ore" refrigerator did not come ah'eadv equil)ped with an automatic icemake_,
an icemaker accessorx kit is axailable at
extra cost,
ToUsetheDispenser
Press the glass gently against the top of the dispenser cradle.
The spill shelf is not sel6(h'aining. To
reduce water spotting, the shelf should be
cleaned regularly.
If nowaterlsdispensedwhentherefweratorisfkst lbsta//ed,theremaybeak inthewater/inesystem.
Pressthedispenserarmforat /easttwomlbutesto removetrappedairfromthewaterfineandto fi//the
watersystem.Toflushouti_npuritiesinthewater fine,throwawaythefirstslkglassfulsof water
Toaccessice.
Check the back of the refl_Jgerator fin. the specific icemaker kit needed fi)r
VOIII" I/] odel.
Locking the Dispenser
Press the LOCKpad fin" 3 seconds to lock the dispenser and control panel. To mflock, press and hold the pad again fin" 3 seconds.
DoorAlarm
To set the alamo, press the DOORALARM pad. The indicator light will ilhmfinate.
This alam_ will sotmd if either door is open fi)r more than 2 minutes. The
beeping stops when you close the dora;
11
Cam and cleaning ofthe refrigerator.
Cleaning the Outside
The doorhandles and trim. Clean with a doth
danq)ened with soapy water: Dry with a soft cloth. Do not use wax on the door handles
and trim.
Keep the outside clean. Wipe Mth a clean cloth lightly dampened Mth kitchen
appliance wax or miM liqtfid dish detergent. Dry and polish with a clean,
soft cloth.
Donot w/_)etherefn_?eratorwith a soileddish clothor wet towel. Thesemayleavea residue
that canerodethe paint.Donot usescouring pads,powderedcleaners,bleachorcleaners containingbleachbecausetheseproductscan
scratchand weakenthepaint finish.
Cleaning the Inside
The stainless steel panels and doorhandles.
Stainless steel (on some models) can be cleaned with a commercially a\_lilable
stainless steel cleane_: A spra}_on stainless steel cleaner works best.
Do not use appliance wax or polish on the stainless steel,
Silver-plated plastic parts. Wash parts Mth soap or other mild detexgents. _4_ipe clean
with a sponge, damp cloth or paper to_vl.
Do not scrub with steel-wool pads or other abrasive cleaners.
Tohelp prevent odors,leave an open box of
baking soda in the reflJgerator and ti'eezer
COIlll)_l rtll/e nts,
Unplug the refrigerator before cleaning. If this
is not practical, wring excess moisture out
of sponge or doth when cleaning aromM
switches, lights or controls.
Lrse an appliance wax polish on the inside
sm'tilce between the doo_.
Use wmm water and baking soda solution--
about a tnblespoon (15 ml) of baking soda
to a quart (l liter) _d wateI: This both cleans
and neutralizes odo_. Rinse and wipe dry.
Alter cleaning the door gaskets, apply a
thin laver of petrolemnjelly to the door gaskets at the hinge side, This helps kee I)
the gaskets fl'om sticking and bending out of shape.
Avoid cleaning cud glass shelves with hot water because the extreme temperature difference may cause them to brea£ Handle glass she/yes carefufl_zBumping tempered g/asscan cause
it to shatter
Donot washanyplastic refngeratorpartsin
thedishwashe_
Silver-accented plastic parts. _'_lsl_ parts
with soapy watex: _ipe clean with a sponge,
damp cloth or paper towel.
Do not scrub with steel-wool pads or other abrasive cleane_.
12
Behind the Refrigerator
Be careful when moving tile refl_Jgerator away fl'om tile wall. _M1t,/pes of floor
coverings can be damaged, pa_licularly cushioned coverings and those with
embossed S/li_lces,
Raise tile leveling legs located at tile bottom fl'ont ot tile refrigerator.
Pull tile refl_Jgerator straight out and return it to position by pushing it straight in.
Preparing for Vacation
g_com
Moving tile refl_Jgerator in a side direction may result in damage to the floor covering
or refrigerator.
I,ower the leveling legs tmtil thev touch tile floo_:
When pushing the refrigerator back, make sure
you don't roll over the power cord or icemaker
supply fine (on some models) and ensure the anti-tli9 bracket is engaged {if equligped).
For long \;l(-ations oi" absen(-es_ i'eil/ove
food and Unl)lug tile refl_Jgei'atoi: Clean tile interior with a baking soda solution of one
tablespoon (15 ml) of baking soda to one quart (1 liter) of water: i,eave the doo_
open.
Set tile icemaker power switch to tile 0 (off) position and shut off tile water supply to
the refl_Jgeratm:
Preparing to Move
Secure all loose items such as base grille, shelves and drawe_ by taping them
securely in place to prevent damage. \_]/en using a hand truck to move tile
refl_Jgerato_; do not rest tile fl'ont or back ot the refl_Jgerator against the hand truck.
This could damage the refl_igerator. Handle only fl'om tile sides of tile refl_igeratm:
If tile temperature can drop below fl'eezing, have a qualified servicer drain the
water supl)ly system (on some models) to
prevent serious property damage due to flooding.
Besurethe refngeratorstaysin anupnght positionduringmoving.
13
Replacingthe lightbulbs.
Turning the control to the 0 (off) position does not remove power to the light circuit.
Refrigerator Lights
Appearance may vary
_i, CAUTION:ahtb./bsmaybeho_
0 Unplug the refrigerator.
To remove the light shield, grasp the
shield at the back and pull out to release the tabs at the back.
0 Rotate the shield down and then
fi)rward to release the tabs at the fl'ont oI the shield.
Freezer Light
A CAUTION:L/_htb./bsmaybehot
Unplug the refrigerator.
The bulb is located at the top of the
fl'eezer inside a light shield. To remove the shield, grasp the shield at the back
and pull out to release the tabs at the back.
_]b Rotate the shield down and then
v
fiwward to release the tabs at the front of the shield.
0 _Mter replacing Mth an appliance bulb
of the same or lower wattage, replace
the shield.
0 Plug the refrigerator back in.
NOYE:Appliav, ce bulbs ma_ be ordered fl'om (;E Parts and Accessocies,
800.626.2002.
_Mter replacing with an appliance bulb
of the same or lower wattage, replace
the shield.
0 Plug the refcigerator back in.
/4
Trimkits anddecoratorpanels.
For panel required models
Read these instructionscompletely and carefully.
Before YouBegin
Some models are equipped with trim kits that aflow you to install door panels. Youcan order pre-cut black or white decorator panels from GE Parts and Accessories, 800.626.2002, or you can add wood panels to match your kitchen cabinets.
Panels less than 1/4" (6mm)thick
_,_]_en installing wood panels less than l/4" (6 ram) thick, you need to create a filler panel, such as l/8"
cardboard, that will fit between the face of the door and the wood panel. If you are installing the i)re-cut decorator panels, i)re-cut filler panels are included in the kit. The combined thickness of the decorator
or wood panel and the filler panel should be 11/32" (8.7 ram) with the panel itself being no larger than 1/4" (6 ram).
Panels1/4"tlfickor less
1/4" max
The handle and the top and bottom trim stand in front of the surii_ce of the do()); which requires that the filler be smaller in lenoth_ and width than the panel. Use the gtfidelines beh)w and tape the filler onto the
back of the panel.
Panel
LeftFreshFoodDoor
Filler
Panel-
FreezerDoor
RightFreshFoodDoor
L
Filler
Filler
Panel _ /5
Trimkits anddecoratorpanels.
3/4" (19mm) or Raised Panel
A raised panel design screwed or glued to a ]/4" (6 ram) thick backing, or a 3/4" (]9 ram) routed board
can be used. The raised portion oI the panel must be tid)Hcated to permit clearances oI at least 2" (5.1 cm)
fl'om the handle side fin" fingertip clearance.
Panels thicker than 1/4" (6 ram), up u) 3/4" (19 ram) max., will require that the outer 5/16" (8 ram) oI
panel perimeter be no thicker than 1/4" (6 ram).
Weightlimitationsfor custompanels:
FreshFood10Ibs.(4.5kg)max.for eachdoor FreezerDoor 18Ibs.(8kg)max.
Panelsthickerthan1/4" (6ram)
1/4"(6 IT,e) ThickBacking
16"(8 mm)
1/4" (6lem)max
3/4" (19ram)
Dimensions for Custom Wood Panels
. ..... 1/8"
",I/4" /
(6mr0).... ::_ ........
5/16" (8 mm) minimumat
1/4" (6 ram)
thickness
Top,left and bottoro
Raisedportion of panel
LeftFreshFoodDoor
iiiiiiiiiiiiiiiiiiiii@Ti_Ti_Ti_Ti_Ti_Ti@@i77117iii_!ill
]_i;i_i_i_i_i_i_i_i_ii_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i'ill_iiiiii_
iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii
iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii
r
2"(5.1 cm) Clearance HandleSide
Appearance Panel
2" (51 ram)
minimumat 1/4" (6 ram)
thickness
Handleside
3815/16" (98.9cm)
2"(51 ram)
mlnlmlJ[i-i at
1/4" (6ram/ thickness
Handleside
Raisedportion of panel
(19mm)
Refrigerator Door
RightFreshFoodDoor
5/16"(8 ram) minimumat
1/4" (6mm) thickness
Top,rightand bottom
38 15/16" (98.9cm)
1629/32" (42.9cm)
2" (51 rom)minimuroat 1/4" (6ram)thickness Freezer Door
Handleside
5/16" (8 ram)minimum at 1/4" (6ram)thickness
Left,right and bottomsides Raised
portion ofpanel
771
_ iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii
I_ 1629/32" (42.9cm)
IJ
'r_ 9529/32-1912cm/ _1-''"',,
1/8" "
..... I .. ..... "':,1/8"
16 "',!_1b_ 1/4)' 1'/4" _t I_!/
" ........ {6taro) (6mm)........ "
,,-" 1/8"
(6mm)......
Installation
Refrigerator
Instructions
Questions? Call 800.GE.CARES (800.432.2737) or Visit our Website at: ge.com
I
BEFORE YOU BEGIN
Read these instructions completely and carefully.
IMPORTANT- Save these instructions for
local inspector's use.
IMPORTANT- Observeallgoverning
codes and ordinances.
Note to Installer- Be sure to leave these instructions with the Consumer.
Note to Consumer- Keep these instructions for future reference.
Skill level- Installation of this appliance requires basic mechanical skills.
Completion time - Refrigerator Installation
In Canada, call 1.800.561.3344 or Visit our Website at: www.geappliances.ca
MATERIALS YOU MAY NEED (not included)
Lag Bolts Anchor Sleeves
Drill Bit Appropriate for Anchors
For Anti-lip Bracket Mounted on CONCRETEFloors 0nly
TOOLS YOU MAY NEED
20 minutes
Water Line Installation 30 minutes
Adjustable Wrench Ratchet/Driver
Models 21 and 25
I
3/8" and 5/16" Socket
Anti--[]p Bracket Installation
20 minutes
Proper installation is the responsibility of the installer.
Product failure due to improper installation is not covered under the Warranty.
PREPARATION
MOVING THE REFRIGERATOR INDOORS If the refrigerator will not fit through a doorway, the
refrigerator door and freezer drawer can be removed.
To remove the refrigerator door, see Step 1in the
Reversing the Door Swing section.
To remove the freezer drawer, see the Removing
the Freezer Drawer section.
WATER SUPPLY TO THE ICEMAKER AND DISPENSER (ON SOME MODELS)
If the refrigerator has an icemaker, it will have to be connected to acold water line. AGE water
supply kit (containing tubing, shutoff valve, fittings and instructions) is available at extra cost from
your dealer, by visiting our Website at ge.com (in Canada at www.geappliances.ca) or from Parts and
Accessories, 800.626.2002 (In Canada 1.888.261.3055).
1/4" Outer Diameter
Compression Nut
and Ferrule (sleeve)
(icemaker models only)
3/32", 1/8" and 1/4"Allen
1/8" Drill Bit and
Electric or Hand Drill
Pencil
Wire Cutters
Phillips Head Screwdriver
wrenches
Tape measure
1/4" Nut Driver
Level
17
Installation Instructions
INSTALLING THE ANTI-TIP FLOOR BRACKET (on 21 ft. models)
[] LOCATING THE ANTI-TIP
FLOOR BRACKET
Place the anti-tip floor bracket Iocator
[]
O
Under certain circumstances, this refrigerator
can tip forward,
Injury to persons can result, Install Anti-Tip Bracket packed with this
refrigerator,
[] MEASURE CABINET OPENING
AVAILABLE VS. REFRIGERATOR WIDTH
Measure width of cabinet opening where refrigerator will be placed, W.
Be sure to account for any countertop
overhang, baseboard thickness and any clearance desired. Width, W, should not
be less than 36 inches. The refrigerator
will be placed approximately in the
middle of this opening.
Baseboard Thickness
or Countertop Overhang
(Whichever Is Greater)
Plus Any Desired
Clearance
RH Side
14 I I
I
REFRIGERATOR
[
Rear Wall
W _:
4_
Front
template (included inside the anti-tip kit) onto the floor up against the rear wall,
within W, and in line with the desired
location of the RH side of the refrigerator (see Figure 1).
Figure 1 - Installation Overview
2 Wall Holes
Bracket on the _s_ RH Side of Locator
Refrigerator / Refrigerator Template Sheet
[] Place the anti-tip floor bracket onto the
Iocator template with its RH floor holes
lined up with the floor holes indicated on the template sheet, approximately 71/4" from the edge of the sheet or the RH side of the refrigerator.
[] Hold down in position and use the anti-tip
floor bracket as a template for marking the holes based upon your configuration and type of construction as shown in Step
3. Mark the hole locations with a pencil,
nail or awl.
NOTE:
It is REQUIRED to use at least 2 screws to mount the floor bracket (one on each
side of the anti-tip floor bracket). Both must be into either the wall or the floor.
Figure 2 indicates all the acceptable mounting configurations for screws. Identify the screw holes on the anti-tip floor bracket for your configuration.
18
Installation instructions
[] LOCATING THE ANTI-TIP
FLOOR BRACKET (cont.)
Figure 2 - Acce.ptable Screw
Placement Locations
Preferred Installation -
Minimum Acceptable #1- Minimum Acceptable #2-
Wood
i i
i
Wall Plate Stud Wood Floor
Minimum Acceptable #3 -
Concrete Floor
Preferred Installation-
Concrete
i i
[] ANTI-TIP BRACKET INSTALLATION
[] WOOD Wall and Floor Construction:
Drill the appropriate number of 1/8" pilot holes in the center of each floor
bracket hole being used (a nail or awl may be used if a drill is not available)
AND remove the Iocator template from the floor.
Mount the anti-tip floor bracket by
fastening the 2, or preferably 4, #10-16
hex-head screws tightly into place as illustrated in Figure 3.
Figure 3- Attachment to
Wall and Floor
2 Screws Floor [-1 Wall
RearRH Must Enter Bracket H
Corner of the Wood or X I I
Refrlgerator.._.__ Metal Stud _ "_, H Wall
[] CONCRETE Wall and Floor Construction:
Anchors required (not provided): 4 each 1/4" x 1 1/2" lag bolts
4 each 1/2" O.D. sleeve anchors
Drill the recommended size holes for
the anchors into the concrete at the center of the holes marked in Step 2.
Install the sleeve anchors into the drilled holes. Place the anti-tip floor bracket as
indicated in Step 2. Remove the Iocator
template from the floor.
Install the lag bolts through the anti-tip
floor bracket and tighten appropriately.
[] WOOD Wall and TILE Floor Construction:
For this special case, locate the 2 wall holes identified in Fig. 1. Drill an angled 1/8" pilot hole (approx. as shown in Fig. 3) in the center of each hole.
Mount the anti-tip floor bracket using
the Minimum Acceptable Installation #1,
as illustrated in Fig. 2.
[] POSITIONING THE REFRIGERATOR
TO ENGAGE THE ANTI-TIP FLOOR
AND BASE BRACKETS
[] Before pushing the refrigerator into the
opening, plug the power cord into the receptacle and connect waterline (if equipped). Check for leaks.
[] Locate the refrigerator's RH side and
move back approximately in line with the RH side of the cabinet opening, W. This should position the anti-tip floor bracket to engage the anti-tip base bracket on the refrigerator.
[] Gently roll the refrigerator back into
the cabinet opening until it comes to a complete stop. Check to see if the refrigerator front lines up with the cabinet front face. If not, carefully rock the refrigerator forward and backward until engagement occurs and you notice that the refrigerator is fully pushed up against the rear wall.
[] OPTIONAL: Adjust the rear (and front)
wheel height settings to fully engage the rear anti-tip brackets, while also aligning the refrigerator front with the cabinet
front face.
J
NOTE:
If you pull the refrigerator out and away from the wall for any reason, make sure the anti-tip floor bracket is engaged when the refrigerator
is pushed back against the rear wall.
19
Installation Instructions
INSTALLING THE REFRIGERATOR
REFRIGERATOR LOCATION
Do not install the refrigerator where the temperature will go below 60°F (16°C) because it
will not run often enough to maintain proper temperatures.
Do not install the refrigerator where the temperature will go above IO0°F (37°C) because it
will not perform properly.
Install it on a floor strong enough to support it fully
loaded.
CLEARANCES
Allow the following clearances for ease of installation, proper air circulation and plumbing and electrical
connections.
Standard Depth Counter Depth Models Models
Sides 1/8" (3 mm) 1/8" (3 mm) Top 1" (25 mm) 1" (25 mm) Back 1" (25 mm) 1/2" (13 mm)
REMOVE TOP CAP (cont.)(onsomemodels)
REINSTALL DOORS, DRAWERS AND TOP CAP
[] Carefully lower the door onto the center hinge.
Reinstall top hinge. NOTE: Ensure the door is properly aligned to the case top to avoid readjustment of the door during top cap
reinstallation.
[] Place cap over the top of the refrigerator. Reinstall
the original screws in the top and back of the cap.
[] Reinstall the bottom freezer drawer. Refer to
"Replacing the Freezer Drawer" section.
REMOVE TOP CAP (onsomemodels)
IMPORTANT NOTE: This refrigerator is34-1/2" deep. Doors and passageways leading to the installation
location must be at least 36" wide in order to leave the doors and handles attached to the
refrigerator while transporting it into the installation location. If passageways are lessthan 36",the
refrigerator doors and handles can easily be scratched
and damaged. The top cap and doors can be removed to allow the refrigerator to be safely moved indoors. Start with Step A.
If it isnot necessary to remove doors, skip Step A. Leave tape and all packaging on doors until the
refrigerator is inthe final location.
SKID REMOVAL: _lt refrigerator to each side to remove skid.
NOTE: Use a padded hand truck to move this refrigerator. Place the refrigerator on the hand
truck with a side against the truck. We strongly
recommend that TWO PEOPLE move and complete
this installation.
[] Locate and remove the two Phillips head screws
on the top of the refrigerator. Remove the two screws on each side at the rear of the top cap.
Lift off and remove top cap.
[] Remove the fresh-food door. Refer to Steps 1
through 3 of "Reversing the Door Swing" section.
[] Remove the bottom freezer drawer. Refer to
"Removing Freezer Drawer" section.
[] Move refrigerator to the installation location.
TopHingeB
[] CONNECTING THE REFRIGERATOR
TO THE HOUSE WATER LINE
(icemaker and dispenser models)
A cold water supply is required for automatic icemaker operation. If there is not a cold water
supply, you will need to provide one. See Installing the Water Line section.
NOTES:
Before making the connection to the refrigerator, be sure the refrigerator power cord
is not plugged into the wall outlet.
If your refrigerator does not have a water filter,
we recommend installing one if your water
supply has sand or particles that could clog the screen of the refrigerator's water valve. Install it
in the water line near the refrigerator. If using GE SmartConnect TM Refrigerator Tubing Kit, you
will need an additional tube (WXO8XIO002) to
connect the filter. Do not cut plastic tube to install filter.
20
Installation Instructions
[] CONNECTING THE REFRIGERATOR
TO THE HOUSE WATER LINE
(cont.)
[] If you are using copper tubing, place a
compression nut and ferrule (sleeve) onto
the end of the tubing coming from the
house cold water supply.
If you are using the GE SmartConnect TM tubing, the nuts are already assembled to the tubing.
[] If you are using copper tubing, insert
the end of the tubing into the refrigerator
connection, at the back of the refrigerator,
as far as possible. While holding the tubing, tighten the fitting.
If you are using GE SmartConnect TM
tubing, insert the molded end of the tubing into the refrigerator connection,
at the back of the refrigerator, and tighten the compression nut until it is hand tight.
Then tighten one additional turn with a wrench. Overtightening may cause leaks.
[] Fasten the tubing into the clamp provided
to hold it in position. You may need to pry
open the clamp.
[] TURN ON THE WATER SUPPLY
(icemaker and dispenser models)
Turn the water on at the shutoff valve (house water supply) and check for any leaks.
[] PLUG IN THE REFRIGERATOR
On models with an icemaker, before plugging in the refrigerator, make sure the icemaker power switch is set to the O (off) position.
See the grounding information attached to the power cord.
One of the illustrations below will look like the connection on your refrigerator.
Icemaker-Ready models
1/4" Copper
Tubing ///1
1/_lamp _'_t_
Compression
Nut _ Ferrule _
(sleeve) _k-'_
Refrigerator /_4 Connection /
Icemaker-lnstalled Models
Ferrule 1/4"
Refrigerator (sleeve) Compression
Connection --
Tubin£
_ Tubing
SmartConnect TM Tubing
1/4" Tubing
Tubing Clamp
[] PUT THE REFRIGERATORIN PLACE
Move the refrigerator to its final location. Make sure the back side of the refrigerator engages the anti-tip bracket properly. The anti-tip floor bracket should line up with the cutout in the back bottom of the refrigerator, and fit through the cutout when the refrigerator is pushed into position. (Refer to page 18, Step 2A for more information.)
[] LEVEL THE REFRIGERATOR
Turn the front roller adjusting screws clockwise to raise the refrigerator,
counterclockwise to lower it. Use a 3/8" hex wrench with extension, or an Roller adjusting screws
adjustable wrench. To adjust the rollers on 21' Counter Depth models: These models also have rear adjustable rollers
so you can align the refrigerator with your kitchen cabinets. Use a 3/8" hex wrench with extension to turn the screws for the rear rollers--
clockwise to raise the refrigerator, counterclockwise to lower it.
21
Installation Instructions
INSTALLING THE REFRIGERATOR (cont.)
[] REMOVE THE FRESH FOOD
DOOR HANDLE
(For placement in the installation location or reversal of the handles - on some models
Stainless steel (on some models):
@ REMOVING
THE DOOR
HANDLE: Loosen the set screws with the 3/32" Allen wrench
and remove Badge the handle. NOTE:
For Double Door
models follow the same procedure on the opposite
door.
Mounting Fasteners
(appearance may vary)
Plastic handle (on some models):
@ REMOVING THE DOOR HANDLE: Depress the
tab on the underside of the handle and slide the handle up and off of the mounting
fasteners.
O REVERSING
THE DOOR
[] REMOVE THE FREEZER DOOR
HANDLE
Stainless steel and plastic handles:
@ Loosen the set screws located on the underside
of the handle with the 1/8"Allen wrench and
remove the handle.
NOTE: If the handle mounting fasteners need to
be tightened or removed use a 1/4" Allen wrench.
some models):
* Remove
the handle mounting
fasteners with a 1/4" Allen wrench and transfer the
handle Mounting mounting
fasteners to the right side. (appearance may vary)
" Remove the
logo badge.
, Remove and transfer the plug button to
the left side of the fresh food door. NOTE:
Use a flat plastic edge to prevent damaging the door. Remove any adhesive on the door with a mild detergent. Remove the paper covering on the adhesive backing on the logo badge prior to carefully attaching the badge
to the door.
Fasteners.
22
Installation Instructions
[] ATTACH THE FRESH FOOD
DOOR HANDLE
Stainless steel handle:
Attach the handle to the handle
mounting
fasteners and tighten the set
screws with a 3/32" Allen
wrench. Mounting NOTE: For Double Fasteners
Door models
follow the same
procedure on the
opposite door.
(appearance may vary)
Plastic handle:
Q Attach the handle to the handle mounting
fasteners by aligning the slots with the handle
mounting fasteners.
O Slide it down until it is firmly locked into
position.
[] ATTACH THE FREEZER DOOR
HANDLE
Stainless steel and plastic handles:
Q Attach the handle firmly to the mounting
fasteners and tighten the set screws on the
bottom of the handle with a 1/8" Allen wrench.
J
J
(appearance may vary)
Slots on back U of handle
(appearance may vary)
A
Mounting
fasteners
23
Installation Instructions
INSTALLING THE REFRIGERATOR (cont,)
I_] LEVEL THE REFRIGERATOR
The leveling legs have 2 purposes:
1) Leveling legs adjust so the refrigerator
is firmly positioned on the floor and
does not wobble.
2) Leveling legs serve as a stabilizing brake to hold the refrigerator securely in position during operation and
cleaning. The leveling legs also prevent the refrigerator from tipping.
[] Remove the grille by removing the two
Phillips head screws.
[] Turn the leveling legs clockwise to raise the
refrigerator, counterclockwise to lower it.
[] SET THE CONTROLS
Set the controls to the recommended setting.
h
he]
0 "FIS RECOMMENDED 37'F ISRECOMMENDED
REMOVE PACKAGING
[]
PlrJ
START ICEMAKER
(icemaker models) A) Remove all tape, foam and protective
packing from shelves and drawers.
B) Remove the tie downs from the freezer
baskets.
C) Place half width basket onto drawer
slides. See About the freezer section for instructions.
Set the icemaker power switch to the I (on) position. The icemaker will not begin to operate until it reaches its operating temperature of 15°F (-9°C) or below. It will then begin operation automatically. It will take 2-3 days to
fill the ice bin.
CAUTION: Toavoidpossible
personal injury or property damage, the leveling legs must be firmly touching
the floor.
[] Replace the base grille by inserting the two
Phillips head screws.
NOTE: In lower water pressure conditions, the
water valve may turn on up to 3 times to deliver enough water to the icemaker.
24
Installation Instructions
REMOVING THE FREEZER DRAWER (on some models)
The freezer drawer can be removed, if needed,
to fit through tight areas.
Read these instructions completely and carefully.
[] REMOVE THE BASKET
[] Open the freezer drawer until it stops. [] Cut the 2 wire ties off of the basket with
wire cutters.
[] The freezer basket rests inside 4 tabs on
the freezer slides. Lift the basket up and
out of the 4 tabs.
[] Tilt the front up and lift the entire basket
up and out of the drawer.
Q
\\\\\\\\\
[] REMOVE THE BASE GRILLE
(if needed)
If, after removing the freezer drawer and refrigerator door, the refrigerator will still not fit through a doorway, the base grille
can be removed.
[] Remove the base grille by removing the
2 Phillips head screws.
[] REMOVE THE DRAWER FRONT
FROM THE SLIDES
[] Remove the 10 hex head screws from the
door and remove the door.
Q DO NOT remove the torx screws
from the rail assemblies.
\
DO NOT remove
torx screws
\
Rail Assembly
[] Set the drawer front non-scratching
surface.
[] Push the rail assemblies back into the
cabinet.
on a
25
Installation Instructions
REPLACING THE FREEZER DRAWER (on some models)
o Two people may be required to complete
I
this procedure.
[] ATTACH AND SECURE THE
DRAWER FRONT TO THE SLIDES
[] Pull out the rail assemblies to the full
length on each side of the cabinet.
[] Drive the top screw into the door on each
side until it is 1/2 way in.
[] ATTACH AND SECURE THE
DRAWER FRONT TO THE SLIDES
(CONT.)
[] Drive screws fully. (There are 10 screws.)
Screw
Step D2: I J Drive
fully•
[] Hang the drawer front onto open slots on
the slides.
Slot
Step D3:
Drive screws in these holes.
-- Step DI: Line up
screw
hole in
freezer drawer and drive
fully.
[] REPLACE THE FREEZER BASKET
Replace the lower freezer basket by lowering it into the frame.
\\\\
\
\
26
Installation Instructions
REVERSING THE DOOR SWING (Single Door Refrigerator Models only)
IMPORTANT NOTES
When reversing the door swing: NOTE: Door swing is not reversible on stainless
steel models. * Read the instructions all the way through
before starting.
* Parts are included in the door hinge kit.
Handle parts carefully to avoid scratching
paint.
Set screws down by their related parts to avoid using them in the wrong places.
Provide a non-scratching work surface for
the doors.
IMPORTANT: Once you begin, do not move the cabinet until door-swing reversal is completed.
These instructions are for changing the hinges from the right side to the left sideiif you ever want to change the hinges back to the right side,
follow these same instructions and reverse all references to left and right.
Once door swing is finalized, ensure
the logo badge is properly aligned and
permanently secured to the door by removing
the adhesive cover on the back side,
NOTE: A replacement logo badge is included in the hinge kit.
Unplug the refrigerator from its electrical outlet. Empty all door shelves, including the dairy
compartment.
[] REMOVE THE
REFRIGERATOR DOOR
[] Tape the door shut with masking tape.
[] Remove the hinge cover on top of the
refrigerator door by removing the Phillips head screws and pulling it up,
[] Using a 5/16" socket ratchet/driver,
remove the bolts securing the top hinge to the cabinet. Then lift the hinge straight up to free the hinge pin from the socket in the top of the door.
O
-linge Cover
TOOLS YOU WILL NEED
Adjustable Wrench
Masking Tape
Phillips Screwdriver
Thin-blade Screwdriver
5/16" Socket
Ratchet!Driver
Torx T-20 Driver
i G
[]
Remove the tape and tilt the door away from the cabinet. Lift the door off the
center hinge pin. Ensure that the plastic hinge pin thimble remains on the hinge pin or inside door hinge pin hole located in the
bottom of the door.
[] Set the door on a non-scratching surface
with the inside up.
27
Hinge
Installation Instructions
REVERSING THE DOOR SWING (cont.)
[] REMOVE CENTER HINGE
Using a 5/16" socket ratchet/driver, remove the bolts securing the center hinge to the cabinet. Set the hinge
and bolts aside.
[] INSTALL CENTER HINGE
[] Transfer the plug button and screw hole
cover in the hinge holes on the left side to
the right side.
TRANSFER REFRIGERATOR
[]
DOOR STOP
[]
Remove the door stop on right side of
the bottom of the refrigerator door by
removing the two screws.
[]
Move the plastic hinge hole thimble to the opposite hole.
[]
Install the door stop on the left side, making sure to line up the screw holes in the door stop with the holes in the
bottom of the door.
Bottom of Bottom of
Refrigerator Door Refrigerator Door
(Right Side) (Left Side)
[] Install the center hinge from the kit on the
left side.
NOTE: A new hinge will be required for the left side (supplied in the door hinge kit).
ITI TRANSFER REFRIGERATOR
DOOR HANDLE TO RIGHT
Refer to Remove the Fresh Food Door Handle and Attach the Fresh Food Door Handle sections for instructions.
28
Installation Instructions
[] REHANG REFRIGERATOR DOOR
[] Lower the refrigerator door onto the
center hinge pin. Ensure that the plastic hinge pin thimble is on the center hinge pin or inside door hinge pin hole located
in the bottom of the door.
[]
Insert the top hinge pin into the hinge hole on top of the refrigerator door. Make sure the door is aligned with the cabinet. Attach the hinge to the top of the cabinet
loosely with the bolts.
[]
Make sure the gasket on the door is flush against the cabinet and is not folded. Support the door on the handle side and
make sure the door is straight and the gap
between the doors is even across the front. While holding the door in place,
tighten the top hinge bolts. Replace the
hinge cover.
[] INSTALL THE LOGO BADGE
Remove the adhesive backing paper and align the pins on the back of the badge with the holes in the door. Apply pressure to the badge to ensure it sticks
to the door.
29
Installation Instructions
REMOVING THE DOORS (Double Door Refrigerator Models only)
IMPORTANT NOTES
NOTE: Door swing is not reversible.
Read the instructions all the way through before starting.
Handle parts carefully to avoid scratching paint.
Set screws down by their related parts to avoid using them in the wrong places.
Provide a non-scratching work surface for
the doors.
IMPORTANT: Once you begin, do not move the cabinet.
These instructions are for removing the doors.
Unplug the refrigerator from its electrical outlet.
Empty all door shelves, including the dairy compartment.
TOOLS YOU WILL NEED
[] REMOVE THE
REFRIGERATOR DOORS
[] Tape the doors shut with masking tape.
(for water dispenser models)
[] Start with right-hand door first: Remove
the screw securing the center hinge cover, lift the hinge cover and place to the side on top of the refrigerator.
aemo__
Adjustable Wrench 3/8" and 10 mm Socket
Masking Tape
Phillips Screwdriver
Ratchet/Driver
Thin-blade Screwdriver
(for water dispenser models)
[] Remove water coupling and power
coupling.
Water Coupling o
Remove the metal spring _
clip. Use a screwdriver to _ ..... -
push the red plastic locking "_ /
clip down and off. _" I __
Power Coupling
Black mark
flush with collar assembly
Pull apart power
coupling to disconnect
30
Loading...
+ 180 hidden pages