GE PDS22SCRBRSS, PDS22SCRBLSS, PDS22SCRALSS, PDS22SCPARSS, PDS22SCPALSS Owner’s Manual

...

GEAppliances.com

Safety In_Ttrudions ........... 2-4

Operating Instruc_tions

Additional Features ............. 9

Automatic Icemaker . .......... 19

Controls .................... 5, 6

Crispers and Pans ............. 10

Freezer ...................... 11

Shelves and Bins ............. 8, 9

_'ater Filter ................... 7

Care and Cleaning ........ 13-15

Installation Instructions

Installing the Refligerator . . . .17-91

Installing the _4'ater Line ..... 30-32

Preparing to Install

the Refligerator . .............. 16

Removing and Replacing the

Freezer Drawer ............ 22, 23

Reversing the Door Swing .... 24-29

Troubleshooting Tips ...... 33, ,°,4

Normal Operating Sounds ...... 33

Models20 and22

Cong_lateur inf>rieur

R frig&ateurs

La section fran_aise commence a la page 41

Congelador inferior

Refrigeradores

La secci6n en espa#ol empieza en la pagina 79

Consumer Support

Consumer Support ..... Back Cover

Performance Data Sheet ........ 39

Product Registration ........ 35, 36

Warranty for Canadian

Customers ................... 37

_'arrantv for U.S. Customers ..... 38

Write the model and serial

numbers here: Model # Serial #

Find these numbex_ on a label on the right side, near the top of

the refl'igerator compartment.

3828JLSO12A 197B4618PO02 49-60282 05-03Jfl

IMPORTANTSAFETYINFORMATION. READALLINSTRUCTIONSBEFOREUSING.

A WARNING!

Use this appliance only for its intended purpose as described in this Owner's Manual

SAFETYPRECAUTIONS

When using electrical appliances, basic safety precautions should be foflowed, including the following:

This refiigerator must be properly installed

and located in accordance with the Installation Instructions before it is used.

Do not allow children to climb, stand or hang

on the shelves in the refl-igerato_: They could damage the refl-igerator and seriously iqjure

themselves.

Do not touch the cold surfi_ces in the fl'eezer

compartment when hands are damp or wet. Skin may stick to these extremely cold sml'i_ces.

, Do not store or use gasoline or other flammable

wq)()_s and liquids in the vicinity of this or anv other appliance.

Keep finge_ out of the "pinch point" areas; clearances between the doo_s and between

the (loo_s and cabinet are necessarily small. Be carefld closing (loo_s when children are

in the area.

In refl-igerato_s Mth automatic icemake_s,

avoid contact with the moving parts ot the

ejector mechanism, or with the heating element that releases the cubes. Do not place finge_s or hands on the automatic icemaking mechanism

while the refi-igerator is plugged in.

Unplug the reli-igerator befi)re cleaning and

making repai_.

NOTE: Westronglyrecommendthat any servicingbe

performedby a quafified individual.

Setting either or both controls to 0 (Off)does not remove power t() the light circuit.

Do not reli'eeze ti'()zen fi)ods which have

thawed completely.

DANGER!RISKOFCHILDENTRAPMENT

PROPERDISPOSALOFTHEREFRIGERATOR

GEAppliances.com

(3hild entrai)ment and suffocation are not problen_s of the past.Junked or abandoned reffigeratm_ are

still dangerous...even if' they will sit for 'ijust a few da_s." If vou are getting rid of yore" old refl_igerator,

please follow the instmcOons below to hel I) prevent accidents.

Before YouThrowAway YourOldRefrigerator

Refrigerants

All refrigeration products contain refl'igerants, which tin(let fe(leral law must be removed prior

to i)roduct disposal. If w)u are getting rid of an old refl'igeration product, check with the

company handling the disposal about what

to do,

or Freezer:

make off the doo_.

I,eave the shelxes in place so that children ma) not easily climb inside.

USEOFEXTENSIONCORDS

Because of potential safety hazards under certain conditions, we strongly recommend against the use of an extension cord.

However, ifxou must use an extension cord, it is absolutely necessary that it be a UI,-listed (in the United States) or a CSA cerOfied (in Canada), 3-wire ,gr°mMing, t_,l)e appliance extension cord having, a ,gr°mMing,

_])e I)lu_*',and outlet and that the electrical rafim*., of the cord be 15 amperes (minimmn) and 120 xolts.

IMPORTANTSAFETYINFORMATION. READALLINSTRUCTIONSBEFOREUSING.

WARNING!

HOWTOCONNECTELECTRICITY

Do not, under any circumstances, cut or remove the third (ground) prong from the power cord.

For personal safety this appliance must be properly grounded.

The power cord of this appliance is equipped

with a &prong (grounding) plug which mates with a standard 3-prong (grounding) wall outlet to

minimize the possibility of electric shock hazard fl'om this appliance.

Have the wall outlet and circuit checked by a qualified electridan to make sure the outlet is

properly grounded.

Where a standard 2-prong wall outlet is

encountered, it is your personal responsibility and obligation to have it replaced with a properly

grounded 3-prong wall outlet. The refl_igerator should always be plugged into its

own individual electrical outlet which has a w)ltage rating that matches the rating plate.

This provides the best perlommnce and also I)rexents oxerloading, house wiring circuits which

could cause a fire hazard fl'om oxerheated wires. Never unplug your refl_igerator by pulling on the

power cord. Mways gill ) plug firefly and pull straight out fl'om the outlet.

Repair or replace immediately all power cords that have become fl'ayed or otherwise damaged. Do not

use a cord that shows cracks or abrasion damage along its length or at either end.

When moving the refi_igerator away from the wall, be carefld not to roll over or damage the power cord.

USEOFADAPTERPLUGS(AdapterplugsnotpermittedinCa_adaJ

Because of potential safety hazards under certain conditions, we strongly recommend against the use of an adapter plug.

Howe\'et; if you must use an adapter; where local codes i)emfit, a temporary connection may be made

to a properly grounded 2-prong wall outlet by use of a UIAisted adaptor a\:filable at most local

hardwai'e stoi'es.

The linger slot in the adapter must be aligned with the larger slot in the _;fll outlet to provide proper

polarity in the connection of the power cord.

When disconnecting the power cord fl'om the

a(lapte_; always hold the adapter in place with one hand while pulling the power cord I)lug with the

other hand. If this is not done, the adapter ground temfinal is very likely to break with repeated use.

If the adapter ground temfinal brea!cs, DO NOT USE the reliJ oerator,_ until a I)r°I ,)er ground has been

established.

Attaching the adapter ground termlhal to a wall outlet cover screw does not ground the appliance unless the

cover screw is metal, and not insulated, and the waft outlet is grounded through the house wiring. Youshould

have the ckcuit checkedby a qualified electrician to make sure the outlet is proper/)/grounde_

READANDFOLLOWTHISSAFETYINFORMATIONCAREFULLY. SAVETHESEINSTRUCTIONS

Aboutthe controlswith

temperaturesettings.(forother models, see nextpage) GEAppl_nce_com

NOTE,"Therefrigeratoris shippedwith protectivefilm coveringthe temperaturecontrols. If this film was notremovedduringinstallation,removeit now

Thetemperature controls are preset in the factory at 37°1:for the refrigerator compartment

and #OFfor the freezer compartment. Allow 24 hours for the temperature to stabilize to the

preset recommended settings.

Thetemperature controls can display both the SET temperature as well as the actual temperature in the refrigerator and freezer. The actual temperature may vary slightly from the SETtemperature based on usage and operating environment.

Setting either or both controls to OFFstops cooling in both the freezer and refrigerator compartments, but does not shut off electrical power to the refrigerator.

Changingthe Temperature

To change the temperature, press and release the WARMER or COLDER pad. The SETlight will c(:,me

on and the display will show the set temperature. To change the teml)eratm'e, tn l) either the

WARMER or COLDER pad until the desired

teilll)erattlre is displayed, Refl'igerator teml)erattlres can be a(!iusted between 34°F and 47°F and the

fl'eezer teInI)eratures can be ac!iusted between

-6°F and +8°E

Once the desired temperature has been set, the temperatm'e display will return to the actual

refi'igei'ator and fl'eezer teml)erattlres afiei" 5 seconds, Several ac!iustments may be required,

Performance A# Flow System

The Pedbm_an('e _Mr Flow System is designed to maMmize temperature control in the refl_igerator

and fl'eezer conq)artmei_ts. This tmique special teatm'e consists of the _dr Tower along the back

Each time you a(!just controls, allow 24 horns fiw the reti-igerator to reach the temperatm'e you have set.

Toturn the cooling system off, tnI) the WARMER pad

fro" either the refl_igerator or the fl'eezer until the display shows OFF.To turn the unit back on, press the

COLDERpad fi)r either the refl_igerator or fl'eezei;

The SErlight will illuminate on the side you selected. Then press the COLDERpad again (on the

side where the SETlight is illuminated) and it will go to the preset points of O°Fflw the fi'eezer and

37°Ffi)r the refl-igeratm; Setting either or both controls to OFFstops cooling in both the fi'eezer

and refi-igerator compartments, but does not shut off electrical power to the refl_igeratm;

wall of the refrigerator and the _Mr Tmmel on the bottom portion of the fl'eezer rear wall. Placing

fi)od in fl'ont of the lou\'e_s on fl_ese components will not affect i)eHbm_ance.

Aboutthecontrolswith

numberedsettings.

NOTE: Therefrigeratoris shippedwith protectivefilm coveringthe temperaturecontrols.

If this film was not removedduringinstallation,removeit now

Initially, set the refrigerator control at 5 and the freezer control at 5 and allow 24 hours for the temperature to stabilize.

Several adjustments may be required. Adjust the controls one increment at a time, and allow 24 hours after each adjustment for the refrigerator to reach the temperature you

have set.

Setting either or both controls to 0 stops cooling in both the refrigerator and freezer compartments, but does not shut off electrical power to the refrigerator.

Performance Air Flow System

The Pedmmance _Mr Flow System is designed to maximize temperature control in the refl_igerator

and fl'eezer compamnents, This tmique special teatuI'e consists of the _,MrTower along the back

wall of the refligerator and the _'Mr Tmmel on the bottom portion of the fl'eezer rear wall. Placing

fi)od in fl'ont of the lou\'e_ on these components

will not affect perfi)m_ance.

Aboutthe water filter.(onsomemodels) GEAppliances.com

Water Filter Cartridge

The water filter cartridge is located in the back upper right corner of the reflJgerator

COilli)a i'tlilent,

When to Replace the Filter

The filter cartridge should be replaced

evex T six monthsor earlier if you notice your

ice cubes becoming smaller:

Filter Bypass Plug

You must use the filter bypass I_lug when a

replacement filter cartridge is not a\_filable. The icemaker will not operate without the

filter or filter 1)ypass I)lug.

Replacement Filters:

To order additional filter cartridges

in the United States, visit our Webs#e,

GEAppliances.com,or carl

Installing the Filter Cartridge

0 ]fyou are replacing the cartridge,

fi_t remove the old one. Open the cartridge cover by pressing in on the tab at the fl'ont and pulling down.

@ Remove the cartridge by slowly rotating

it cotmterclockwise. A small amount ot water may drip down.

GE Parts and Accessories, 800.626.2002.

Filter Model (;S_,VF Suggested Retail Price ,$34.95 USD

Customei_ in Canada should consult the yellow pages tor the nearest Camco

Se_Mce Center;

CAUTION:/f , h sbeen

in thesystem,the filtercartridgemaybeejectedas

it isremovedUsecautionwhenremoving.

Mark you calender or apply the month and year sficke_; to remind w)u

to replace the filter cartridge in six

months.

O Remoxe the protective fi)il from the

end of the cartridge.

Lining up the arrow on the cartridge and the cartridge holder; slowly rotate

the cartridge clockwise m_til it stops. \4]_en the cartridge is properly

installed, you will teel it "click" as it locks into place. The blade on the end

ot the cartridge should be positioned

vertically: Do not overtighten.

O Close the cartridge cove_:

Aboutthe shelvesandbins.

Not all features are on all models.

Rearranging the Shelves

S S Y _ "

hel;e,_ in the refi_i_e_ato_ ('()ml)artment are a(!iustable

Refrigerator Compartment

Toremove:

: o

0 Tilt the shelf up at the fi'ont.

0 I,ifl the shelf ul) at the back and

bring the shelf ()tit.

Somemodelshavewireshelvesthat canbeadjustedinthesamemamTe_

Toreplace:

_,_hile tiltino_ the shelf u ), insert the tel )

hook at theback of thelsheff in a slot

(m the track.

0 I,ower the fi'ont of the shelf until the

bottom of the shelf locks into place.

Spillproof Shelves (onsomemode/s)

Spillproof shelves have special edges to hel I) prevent spills fl'om dripping to lower

shelves. To i'elnove oi" replace the shelves, see Rearranging the Shelves,

Slide-Out Spillproof Shelf (onsome models)

The slide-out spillproof shelf allows you to reach items stored behind otheis. The

spedal edges are designed to hel I) prevent spills from dripping to lower shelves.

Toremove:

0 Reinove all items from shell 0 Slide the shelf ()tit until it stops.

iift the fl'ont edge of the shelf until the central tabs are above the fl'ont bai:

0 Continue pulling the shelf torward

until it can be removed.

Toreplace:

0 Place the rear shelf tabs just in fi'ont of

the central notches on the shelf fl'ame,

Slide the shelf in until the central tabs are slightly behind the fl'ont bar.

0 i,ower the shelf into place until it is

horizontal and slide the shelf in.

Make surethat the shelf sitsflat after reinstallation anddoesn't move freely fromside to side.

Make sureyoupush the shelvesall the wayin before youclose the door

Not all features are on all models.

GEAppliances.com

iFingerhold

.,S!/ugger

Adjustable Bins on the Door

A(!justable bins can easily be carried fl'om

reflJgerator to work area.

Toremove: lilt bin straight up, then

pull out.

Toreplace or relocate: Engage the bin in the

molded supports ol the doox; and push in. Bin will lock in place.

Non-Adjustable Shelves on the Door

Toremove: IJfl the shelf straight up, then

pull out.

Toreplace: Engage the shelf in the m olded

supports on the door and push down.

It will lock in place,

The snugger helps prevent tipping, spilling

or sliding of small items stored on the door shelt_ G_Jp the finger hold near the rear ol

the snugger and move it to fit your needs.

Aboutthe additional features.

Not all features are on all models.

Shelf Saver Rack (onsomemodels)

Slide-out beverage rack holds twelve cans of soda or two wine/water bottles (lengthwise).

It can be remoxed fin" cleaning.

To remove, slide the rack out to the stop

position, lilt the rack up and past the stop position and lift it ()tlt.

Aboutthe crispersandpans.

Not all features are on all models.

Fruit and Vegetable Crisper

Excess water that ma) ac('tmmlate in the bottom of the drawei_ or under the drawei_

should be wiped dry.

Adjustable Humidity Crisper (onsomemodels)

Slide the control all the way to the Slide the control all the wax to the LOW HIGHsetting to proxide high lmmidit_ .settin,,-., to proxide lower lmmiditv, lmels

reconnnended fi)r most xegetables, reconnnended fi)r most fl'uits.

Snack Pan (on some models)

7th SLOT FROM

BOTTOM

I °

II II

This pan can be Ino_ed to the most useflll location fin" )our fmnil)'s needs.

To remove, slide the pan out to the stop

position, lilt the pail tl I) and past the stop position and lift it out.

Adjustable Temperature Dell Pan (onsomemodels)

"_ hen the pan is placed ill the 7th slot fron/ The settings can be a(!justed am'where the 1)ottom of the track and the lever is set between cold * and coldest _ *. at COLDEST, aix" fl'om the fl'eezer is fiwced around the pan to kee I) it xerv cold. _q_en set at cold, the pan will stay at the

You can lnoxe the pan to all) location if

you don't want the extra cold storage. The coldest setting proxides the coldest

noi]nal refl_igerator telnperature.

stoi'a (e ai'ea.

Crisper Removal

ToRemove:

These dx'awex_ can be x'exnoved easily by lifting up slighfl)while pulling the drawer

past the stop location.

When the door cannot be fully opened,

rem()_'e the dra wer filrth est from the door first. Make sure the drawer closest to the

door is filllv closed. There is a latch at the fl'ont of the center slide rail. Push down on the latch and slide the center slide Ivlil, to

which the drawer is attached, al_lv fl'oln the

dooI: Relnove file drawer

Aboutthe freezer. GEAppliances.com

Not all features are on all models.

Freezer Shelves and Baskets

Depending on your model, your fi'eezer

Ill[ly feattlI'e:

Appearance and features may vary

Appearancemayvary

O A deep fllll-width basket

A shallow fllll-width basket

0 A half:width basket

Basket/Sheff Removal

Toremove the deep full-width basket on

freezer drawer models:

0 Open tile freezer drawer until it stops. @ Tile fl'eezer basket rests on a fl'anle

inside tile fl'eezer (h'awe_; i,ift tile basket up at tile back.

Toremove the half-width basket:

0 Pull tile basket out to tile stop location. @IJtt tile basket up at tile ti'ont to release

it from the slides.

Tab

Lift the back up and out of the slide.

A flfll-width wire shelf

O A shelf aboxe tile ice storage bin

0 Lift tile fl'ont up and lift tile entire

basket up and out of tile (h'awe_:

When replacing the basket make sure that

tile Mre tabs and wire l/oo]_; on tile sides of the basket go into the slots in the sides

of tile basket ti'ame.

NOTE.'_Mwavsbe sure to fiflly close this basket. You will know it is fifllx closed when

xou teel it "click" into place.

Appearance may vary

Toremove the deep full-width baskets on

freezer door models, theshallow full-width basket and the full-width wire shelf."

O Pull tile basket/shelf out to tile stop

location.

IJfl tile fl'ont up and oxer tile stop location.

Toremove the shelf above _e ice bin:

Pull tile shelf straight out.

Lift tile basket/shelf up and out.

Aboutthe automaticicemaker.

A newly installed refrigerator may take 12to 24 hours to begin making ice.

_ower Automatic Icemaker (onsomemodels)

Switch

The icemaker will produce seven cubes per c)'cle---al)l)roxinlately ] 00-130 cubes

in a 24-hour period, depending on fl'eezer

COillpai'tlllent [eillpei'attli'e_ i'OOill

teml)erature , ilumber ot door ol)enings and other use conditions.

PowerLight FeelerArt the pi)wel" switch.

See below fin" how to access ice and reach

If the refl_gerator is operated before the

w;Itel" connection is lllade [1) the icell/akeF,

set the power switch in the 0 (off) position.

When the refl_igel'ator has been connected

to/lie water SUl_l_l)', set/lie l)l>wer switch tl) the I (on) position,

The icemaker will fill with water when it

cools to 15°F (-10°C). A newly installed I'efiJgeIzltor may take 12 tl) 24 houIS tl> beg_n

making ice cubes.

You will hear a buzAng sot/lid each filUe

the icemaker fills with water:

Throw away the first few batches ot ice to allow the water line to clem:

Be sm'e nothing intet_feres with the sweep ot the teeler amL

X&]_en the bin fills to the level of the feeler

am_, the icemaker \\'ill stop producing ice. It is nomml for several cubes to be

joined together:

If ice is not used fl'equenfl> old ice cubes

\\'ill become cloud); taste stale and shrink.

NOTE: Inhomes with lower-than-averagewater pressure,you mayhear theicemakercyciemuitlpie

times whenmaking onebatchof ice.

Shelf

Toreach the power switch.

Accessing Ice and Reaching the Power Switch

Toreach the icemaker power switch, pull the

shelf above the ice bin straight out. _M\\'avs be sure to replace the shell

Toaccess ice, simply pull the bin flw\\'ard.

Icemaker Accessory Kit

If your refi_gerator did not come ah'eadv equipped with an automatic icemakex;

an icemaker accessory kit is available at extra cost,

To access ice,

Check the back of the refl_igerator fi)r the spedfic icemaker kit needed fi)r

your Inodel.

Careand cleaning ofthe refrigerator. GEAppliances.com

Cleaning the Outside

The doorhandles and trim. Clean with a cloth

daml)ened with soapy water: Dry with a sott cloth. Do not use wax on the door handles

and trim.

Keep the outside clean. _]i)e Mth a clean cloth lightly dampened Mth kitchen

appliance wax or mild liquid dish detergent. D_3' and polish with a clean,

soft cloth.

Do not w/_)ethe refrigerator with a soiled dish cloth or wet towel Thesemay leave a residue that can erode the pa/nL Do not usescouring

pads,powdered cleaners, bleach or cleaners containing bleach because these products can

scratch and weaken the paint finish.

Cleaning the Inside

The stainless steel panels and doorhandles.

Stainless steel (on some models) can be cleaned with a commerdallv available

stainless steel cleanex: A spray-on st;finless steel cleaner works best.

Do not use appliance wax or polish on the stainless steel,

Tohelp prevent odors, leave an open box o_

baking soda in the refi_igerator and ti'eezer

COIIII)_I i'tlilents.

Unplug the refrigerator before cleaning. If this

is not practical, wring excess moistm'e out

of sponge or cloth when cleaning arotmd

switches, lights or controls.

Use an appliance wax polish on the inside

sm_hce between the (loo_.

Use warn/water and baking soda solution--

about a tablespoon (l 5 ml) of baking soda

to a quart (l liter) of water; This both cleans

and neutralizes odo_. Rinse and wipe (h_'.

_Mter cleaning the door gaskets, apply a

thin layer of petrolemn.jelly to the door gaskets at the hinge side. This helps kee I) the gaskets ti'om sticking and bending out

of shape.

Avoid cleaning cold glass shelves with hot water because the extreme temperature difference may cause them to break. Handleglass shelves carefullg Bumping tempered g/ass can cause

it to shatter

Donot washanyplasticrefngeratorpartsin thedishwasher

Careand cleaning of the refrigerator.

Behind the Refrigerator

Be caretul when moving the refl_igerator away fl'om the wall. M1 types of floor

coverings can be (lamaged, particularly cushioned coverings and those with

embossed s/ii]_lces.

Pull the retiigerator straight out and return it m position by pushing it straight in.

Moving the refligerator in a side direction may result in damage to the floor covering

or reffigeratoi:

Preparing for Vacation

When pushing the refrigerator back, make sure

you don't rofl over the power cord or icemaker

supply line (on some models).

For long \;l(-ations or absen(-es_ i'eillOVe

food and unplug the refl_igerattn: Move the ti'eezer control to the 0 (0fi) position,

and clean the inmrior with a baking soda solution of one tablespoon (l 5 ml) _ff

baking soda to one qtlart (1 liter) of wami: i,eave the clom_ open.

Set the icemaker power switch to the 0 (off) position and shut off the water supply to

the reffigeratm:

Preparing to Move

Secm'e all loose items such as base grille, shelves and drawei_ by taping them

seetlrely in place to prevent dmnage.

If the temperature can drop below freezing, have a qualified servicer drain the

water supply system (oil some models) to prevent serious propel F dmnage due to

flooding.

Besuretherefrigeratorstaysin anupwht positionduringmowbg

Replacingthelightbulbs. GEAppliances.com

Turning the control to the 0 (off) position does not remove power to the light circuit.

Refrigerator Lights

Appearance may vary

CAUTION:ah,b./bsmaybeho_

0 Unplug the refl_geratoi:

@ Tile bulbs are located at tile top of tile

refl_gerator compartment behind tile controls. To remoxe the light shield,

,grasI ) the shield at the back and pull

out to release the tabs at the back.

_]_ Rotate tile shield down and then

fin'ward to release the tabs at the fl'ont of the shield.

Freezer Light

P' CAUTION:L,_h,b.lbsma_beho_

Unplug tile reti_igerato_:

0 Tile bulb is located at tile top of tile

freezer inside a light shield. To relnove the shield, grasp the shield at the back

and pull out to release tile tabs at tile back.

_Mter replacing with an appliance bulb

of the same or lower wattage, replace the shield.

0 Plug tile refl_igerator back in.

@ _Mter replacing with an appliance bull)

of the same or lower wattage, replace the shield.

0 Plug tile refl_igerator back in.

Rotate tile shield down and then forward to release the tabs at the fl'ont

of the shield.

Installation

Refrigerator

Instructions

I Questions? Call 800.GE.CARES (800.432.2737) or Visit our Website at: GEAppliances.com

BEFORE YOU BEGIN

Read these instructions completely and carefully.

• IMPORTANT - Savethese

instructions for local inspector's use.

• IMPORTANT - Observeall

governing codes and ordinances.

• Note to Installer - Be sure to leave these instructions with the Consumer.

• Note to Consumer - Keep these instructions for future reference.

In Canada, call 1.800.361.3400 or Visit our Website at: geappliances.ca

PREPARATION (cont.)

WATER SUPPLY TO THE ICEMAKER If the refrigerator has an icemaker, it will have

to be connected to a cold water line. AGE water

supply kit (containing tubing, shutoff valve, fittings and instructions) is available at extra cost from your dealer, by visiting our Website at GEAppliances.com (in Canada at geappliances.ca) or from Parts and Accessories,

800.626.2002 (In Canada 1.888.261.3055).

Models 20 and 22

TOOLS YOU MAY NEED

• Skill level - Installation of this appliance requires basic mechanical skills.

• Completion time - Refrigerator Installation

20 minutes

Water Line Installation 30 minutes

• Proper installation is the responsibility of

the installer.

Adjustable Wrench

3/8" Head Socket Driver

(a 6-point socket is

recommended)

• Product failure due to improper installation is not covered under the Warranty.

PREPARATION

MOVING THE REFRIGERATOR INDOORS If the refrigerator will not fit through a doorway,

the refrigerator door and freezer drawer or door (depending on model) can be removed.

• To remove the refrigerator door, see Step 1 in the Reversing the Door Swing section.

• To remove the freezer drawer, see the

Removing the Freezer Drawer section.

• To remove the freezer door, see Steps 2 and 3 in the Reversing the Door Swing

section.

1/4" Outer Diameter

Compression Nut

and Ferrule (sleeve)

(icemaker models only)

Phillips Head Screwdriver

Installation Instructions

INSTALLING THE REFRIGERATOR

REFRIGERATOR LOCATION

• Do not install the refrigerator where the

temperature will go below 60°F (16°C)

because it will not run often enough to maintain proper temperatures.

• Do not install the refrigerator where the

temperature will go above 100°F (37°C)

because it will not perform properly.

• Install it on a floor strong enough to support it fully loaded.

CLEARANCES

Allow the following clearances for ease of installation, proper air circulation and plumbing and electrical connections.

Sides 1/8" (4 mm) Top 1" (25 mm) Back 1" (25 mm)

[] CONNECTING THE REFRIGERATOR

TO THE HOUSE WATER LINE (icemaker models)

A cold water supply is required for automatic icemaker operation, If there is not a cold water supply, you will need to provide one. See Installing the Water Line

section.

NOTES:

• Before making the connection to the refrigerator, be sure the refrigerator power cord is not plugged into the wall

outlet. If your refrigerator does not have a

water filter, we recommend installing

one if your water supply has sand or particles that could clog the screen of

the refrigerator's water valve. Install it

in the water line near the refrigerator. If using GE SmartConnect TMRefrigerator

Tubing Kit, you will need an additional tube (WX08X10002) to connect the filter.

Do not cut plastic tube to install filter.

Installation Instructions

INSTALLING THE REFRIGERATOR (cont,)

[] CONNECTING THE REFRIGERATOR

TO THE HOUSE WATER LINE

(cont.)

[] If you are using copper tubing, place a

compression nut and ferrule (sleeve) onto

the end of the tubing coming from the

house cold water supply.

If you are using the GE SmartConnect TM

tubing, the nuts are already assembled to

the tubing.

[] If you are using copper tubing, insert

the end of the tubing into the refrigerator

connection, at the back of the refrigerator, as far as possible. While holding the

tubing, tighten the fitting.

If you are using GE SmartConnect TM

tubing, insert the molded end of the

tubing into the refrigerator connection,

at the back of the refrigerator, and tighten

the compression nut until it is hand tight.

Then tighten one additional turn with a

wrench. Overtightening may cause leaks.

[] Fasten the tubing into the clamp provided

to hold it in position. You may need to pry

open the clamp.

[] TURN ON THE WATER SUPPLY

(icemaker models)

Turn the water on at the shutoff valve (house water supply) and check for

any leaks.

[] PLUG IN THE REFRIGERATOR

On models with an icemaker, before plugging in the refrigerator, make sure

the icemaker power switch is set to the

0 (off) position.

One of the illustrations below will look like the connection on your refrigerator.

1/4" -- Tubing

Copper Clamp Tubing

1/4"

Compression Nut

(sleeve)

Refrigerator Connection

Tubing Clamp

1/4"

Com_

Ferrule (sleeve)

Refrigerator Connection

SmartConnect TMTubing

Tubing

1/4"Tubin

See the grounding information attached

to the power cord.

[] PUT THE REFRIGERATOR

IN PLACE

Move the refrigerator to its final location.

Installation Instructions

[] ATTACH REFRIGERATOR

DOOR HANDLE

[] Look for an arrow label on the front of

the handle.

If the door mounting screws are located on the left side of the door, hold the handle so the arrow points to the right (arrow is at the top of the handle).

If the door mounting screws are located on the right side of the door, hold the handle so the arrow points to the left

(arrow is at the bottom of the handle).

.-,

Door handle

on left side

Door

handle

on right

side

[] ATTACH REFRIGERATOR

DOOR HANDLE (cont.)

[] Holding the handle with both hands,

press it firmly against the front of the door and slide the handle down. This

may require some force.

Screws

mounted

on door

Keyhole slots

on back of handle

[] Align keyhole slots on the top and bottom

of the back of the handle with the screws mounted on the front of the door. Press

the handle against the door front, making

sure that the screws go into the keyhole slots.

Installation Instructions

INSTALLING THE REFRIGERATOR (cont,)

[] ATTACH FREEZER DOOR HANDLE

[] Look for an arrow label on the front of the

handle. Hold the handle so that the arrow is pointing to the left.

[] Align keyhole slots on the right and left

sides of the back of the handle with the screws mounted on the front of the

door/drawer. Press the handle against the door/drawer front, making sure that the screws go into the keyhole slots.

[] Holding the handle with both hands,

press it firmly against the front of the door and slide the handle to the left.

Screws mounted on door

[] LEVEL THE REFRIGERATOR

The leveling legs have 3 purposes:

1) Leveling legs adjust so the door closes

easily when opened about halfway.

(Front of the refrigerator should be 1/4" [6 mm] higher than the rear of

the refrigerator).

2) Leveling legs adjust so the refrigerator

is firmly positioned on the floor and

does not wobble.

3) Leveling legs serve as a stabilizing

brake to hold the refrigerator securely in position during operation and

cleaning.

[] Turn the leveling legs clockwise to raise the

refrigerator, counterclockwise to lower it.

CAUTION: Toavoidpossible

personal injury or property damage, the leveling feet must be firmly touching

the floor.

[]

Install the base grille by aligning the prongs on the back of the grille with the

holes in the cabinet. Push forward until

the grille snaps into place.

Keyhole slots

on back of

handle

Installation Instructions

[] SET THE CONTROLS

Set the controls to the recommended setting.

5 5

[.EOOMME.OEOCO.T.OLSE ..OS]

0 "F IS RECOMMENDED 37 _F IS RECOMMENDED

START THE ICEMAKER

[]

(icemaker models)

Set the icemaker power switch to the I (on) position. The icemaker will not begin to operate until it reaches its operating temperature of 15°F (-9°C) or below. It will then begin operation automatically. It will take 2-3 days to

fill the ice bin.

Pow

switch - I

NOTE:

In lower water pressure conditions, the water valve may turn on up to 3 times to deliver enough water to the icemaker.

Installation Instructions

REMOVING THE FREEZER DRAWER (on some models)

[]

The freezer drawer can be removed, if needed,

to fit through tight areas.

Read these instructions completely and carefully.

[] REMOVE THE BASKET

[] Open the freezer drawer until it stops. [] The freezer basket rests on a frame inside

the freezer drawer. Lift the basket up at the back.

[] Lift the front up and lift the entire basket

up and out of the drawer.

REMOVE THE DRAWER FRONT FROM THE SLIDES (cont.)

[]

Lift up on both sides of the freezer drawer

handle to separate the drawer railings

from the rail assemblies.

[] Set the drawer front on a non-

scratching surface.

[] Push the rail assemblies back into

locking position.

[] REMOVE THE DRAWER FRONT

FROM THE SLIDES

[] Remove the Phillips head screw on each

side of the railing.

(_ DO NOT remove the hex head

screws from the rail assemblies.

DO NOT remove hex head screws

Rail Assembly Drawer

REMOVE THE LEVELING LEGS

[]

Assembly

(if needed)

If, after removing the freezer drawer and

refrigerator door, the refrigerator will still

not fit through a doorway, the leveling leg

brackets can be removed.

[] Remove the base grille by grasping it at

the bottom and pulling it straight out.

[] Remove both brackets with a 3/8" hex

head driver.

DO NOT remove hex head screws

Installation Instructions

REPLACING THE FREEZER DRAWER (on some models)

[] ATTACH AND SECURE THE

o Two people may be required to complete

[] ATTACH AND SECURE THE

[] Pull out the rail assemblies to the full

this procedure.

DRAWER FRONT TO THE SLIDES

length on each side of the cabinet.

DRAWER FRONT TO THE SLIDES

(cont.)

[] Replace the Phillips head screws on both

rail assemblies.

Phillips

Screw

[] Locate the slots on the inside of the rail

assemblies near the back.

Rail assembly

[] Insert the hooks at the back of the

drawer railings into the slots on the rail assemblies.

[] Lower the front of the drawer, making

sure the tabs on the sides of the railings fit into the front slots in the rail assemblies.

[] REPLACE THE FREEZER BASKET

Replace the lower freezer basket by

lowering it into the frame.

Slot

Tab

Installation Instructions

REVERSING THE DOOR SWING

IMPORTANT NOTES

When reversing the door swing:

• Read the instructions all the way through before starting.

• Handle parts carefully to avoid scratching paint.

• Set screws down by their related parts to avoid using them in the wrong places.

• Provide a non-scratching work surface for

the doors.

IMPORTANT: Once you begin, do not move the cabinet until door-swing reversal is completed.

These instructions are for changing the hinges from the right side to the left sideiif you ever want to change the hinges back to the right side, follow these same instructions and reverse all references to left and right.

Unplug the refrigerator from its electrical

outlet. Empty all door shelves, including the dairy

compartment.

[] REMOVE THE

REFRIGERATOR DOOR

[] Tape the door shut with masking tape.

[] Remove the hinge cover on top of the

refrigerator door by squeezing it and pulling it up,

[] Using an adjustable wrench, remove the

bolts securing the top hinge to the cabinet. Then lift the hinge straight up to free the hinge pin from the socket in the top of

the door.

TOOLS YOU WILL NEED

3/8" Head Socket Driver

Adjustable Wrench

Masking Tape

(a 6-point socket is

recommended)

Putty Knife or

Thin-blade Screwdriver

Hinge Cover

Top Hinge

[] Remove the tape and tilt the door away

from the cabinet. Lift the door off the center hinge pin.

[] Set the door on a non-scratching surface

with the inside up.

Installation Instructions

[] REMOVE THE CENTER HINGE PIN

[] On models with a freezer door, tape the

door shut with masking tape.

[] Using an adjustable wrench, remove the

center hinge pin.

[] REMOVE THE FREEZER DOOR

(freezer door models)

[] Remove the tape and tilt the door away

from the cabinet. Lift the door off the bottom hinge pin.

NOTE: There is a plastic washer between

the hinge and the top of the freezer door.

Do not lose.

[] TRANSFER BOTTOM HINGE

BRACKET (freezer door models)

[] Remove the base grille by grasping it at

the bottom and pulling it straight out.

lj j

[] Using a 3/8" socket driver, remove the

screws securing the bottom hinge bracket

to the cabinet.

[] Using an adjustable wrench, remove the

hinge pin and washer(s) from the right side of the bracket and install on the left.

[] Set the door on a non-scratching surface

with the inside up.

[] REMOVE CENTER HINGE

Using an adjustable wrench and Phillips head screwdriver, remove the bolts and screws securing the center hinge to the cabinet. Set hinge, bolts, screws, washer (on freezer door models) and hinge pin

aside.

On models with a freezer drawer, skip to Step 7.

[] Using a 3/8" socket driver, remove the

leveling leg bracket from the bottom left side of the cabinet and install it on the

right side.

Left Side Right Side

Installation Instructions

REVERSING THE DOOR SWING (cont.)

[] TRANSFER BOTTOM HINGE

BRACKET (freezer door models, cont.)

[] Install the bottom hinge bracket on the

left side of the cabinet.

[] Remove the insert at the top left side of the

base grille and install it on the right side.

[] TRANSFER FREEZER DOOR STOP

(freezer door models)

[] Remove the door stop on right side of the

bottom of the freezer door by removing

the two screws.

[] Move the plastic hinge hole thimble to the

opposite hole.

[] Install the door stop on the left side.

Bottom of Freezer Door

(Right Side)

Bottom of Freezer Door

(Left Side)

[] Replace the base grille by aligning the

prongs on the back of the grille with the holes in the cabinet. Push forward until

the grille snaps into place.

Installation Instructions

[] INSTALL CENTER HINGE

[] Transfer the plug button and screws in

the hinge holes on the left side to the

right side.

[] Install the center hinge on the left side.

[] HANG THE FREEZER DOOR

(freezer door models)

Lower the freezer door onto the bottom hinge pin, then shut the door, making

sure to align the door with the cabinet. Make sure the gasket on the door is flush against the cabinet.

[] INSTALL CENTER HINGE PIN

[] Install the center hinge pin.

NOTE: On models with a freezer door, be sure to put the washer between the

top of the freezer door and the bottom

of the center hinge,

Freezer Door Models Freezer Drawer Models

TRANSFER REFRIGERATOR

[]

DOOR STOP

[]

Remove the door stop on right side of the bottom of the refrigerator door by removing the two screws.

[]

Move the plastic hinge hole thimble to the opposite hole.

[]

Install the door stop on the left side, making sure to line up the screw holes in the door stop with the holes in the

bottom of the door.

Bottom of

Refrigerator Door

(Right Side)

Bottom of

Refrigerator Door

(Left Side)

Installation Instructions

REVERSING THE DOOR SWING (cont.)

[] TRANSFER REFRIGERATOR

DOOR HANDLE TO RIGHT

In order to correctly install the handle on the right side, place

a small piece of masking tape

near the top of the handle before removing.

[]

Grasp the handle tightly with both hands and slide the handle up (this may require some force). The keyhole slots on the

back of the handle allow the handle to separate from the mounting screws.

Screws

mounted on door

Keyhole slots on back of handle

TRANSFER REFRIGERATOR DOOR HANDLE TO RIGHT (cont.)

[]

Holding the handle so the masking tape is at the bottom, align keyhole slots on the top and bottom of the back of the

handle with the screws mounted on the front of the door. Press the handle

against the door front, making sure that the screws go into the keyhole slots.

[]

Grasping the handle with both hands, press it firmly against the front of the

door and slide the handle down. This may require some force.

Keyhole slots

on back of handle

Screws

mounted on door

[] Using an adjustable wrench, remove

the handle mounting screws.

[] Carefully pry off the logo badge and plug

button. Remove a layer of adhesive and backing to expose new adhesive. Install logo badge and plug button on left side.

[] Install the handle mounting screws on

the right side.

Installation Instructions

[] REHANG REFRIGERATOR DOOR

[] Lower the refrigerator door onto the

center hinge pin.

[]

Insert the top hinge pin into the hinge hole on top of the refrigerator door. Make sure the door is aligned with the cabinet. Attach the hinge to the top of the cabinet loosely with the bolts.

[]

Make sure the gasket on the door is flush against the cabinet and is not folded. Support the door on the handle side and make sure the door is straight and the gap between the doors is even across the front. While holding the door in place,

tighten the top hinge screws. Replace the

hinge cover,

Installation Instructions

INSTALLING THE WATER LINE (ICEMAKER MODELS)

BEFORE YOU BEGIN

Recommended copper water supply kits are

WX8X2, WX8X3 or WX8X4, depending on the

amount of tubing you need. Approved plastic

water supply lines are GE SmartConnect TM

Refrigerator Tubing (WX08X10002,

WX08X10006, WX08X10015 and WX08X 10025).

When connecting your refrigerator to a GE

Reverse Osmosis Water System, the only approved installation is with a GE RVKit. For other reverse osmosis water systems, follow

the manufacturer's recommendations.

If the water supply to the refrigerator is from a Reverse Osmosis Water Filtration System

AND the refrigerator also has a water filter,

use the refrigerator's filter bypass plug. Using the refrigerator's water filtration cartridge in conjunction with the RO filter can result in

hollow ice cubes. This water line installation is not warranted

by the refrigerator or icemaker manufacturer.

Follow these instructions carefully to

minimize the risk of expensive water damage. Water hammer (water banging in the pipes)

in house plumbing can cause damage to

refrigerator parts and lead to water leakage

or flooding. Call a qualified plumber to correct water hammer before installing the water

supply line to the refrigerator. To prevent burns and product damage, do not

hook up the water line to the hot water line.

If you use your refrigerator before connecting the water line, make sure the icemaker power

switch is in the O (off) position.

Do not install the icemaker tubing in areas where temperatures fall below freezing.

When using any electrical device (such as a

power drill) during installation, be sure the

device is double insulated or grounded in a

manner to prevent the hazard of electric

shock, or is battery powered. All installations must be in accordance with

local plumbing code requirements.

WHAT YOU WILL NEED

• Copper or GE SmartConnect TM Refrigerator Tubing kit, 1/4" outer diameter to connect

the refrigerator to the water supply. If using copper, be sure both ends of the tubing are

cut square.

To determine how much tubing you need: measure the distance from the water valve

on the back of the refrigerator to the water supply pipe. Then add 8' (2.4 m). Be sure

there is sufficient extra tubing (about 8' [2.4 m] coiled into 3 turns of about 10" [25 cm] diameter) to allow the refrigerator to move

out from the wall after installation. GE SmartConnect TMRefrigerator Tubing Kits

are available in the following lengths: 2' (0.6 m) - WXO8XIO002

6' (1.8 m) -WXO8XIO006

15' (4.6 m) - WXO8X10015

25' (7.6 m) - WXO8X10025

Be sure that the kit you select allows at least

8' (2.4 m) as described above.

+ 90 hidden pages