GE GBS22HB, PDS20SB, GBS20KB, PDS20MB, PDS22MB User Manual

Icemaker Accessory Kit

Addendum for IM4, IM4A and IM6 Icemaker Kits

www.GEAppliances.com

197D5736P002 49-60319 12-03 JR

IMPORTANT: These

instructions are needed to

install an icemaker in your

refrigerator. To be used

with an IM4, IM4A or IM6

Icemaker Kit. Keep this

addendum with your

Owner’s Manual and

Installation Instructions.

Installation Instructions

Addendum

GBS20KB

GBS22HB

GBS22KB

PDS20MB

PDS20SB

PDS22MB

PDS22SB

These instructions

are to be used to

install an Icemaker

Kit in the models

listed below.

2

NEEDED CONTENTS OF KIT

The following are a list of the parts from the kit that will be needed to install the icemaker.

Owner’s Manual &

Installation Instructions

2

Water Line Clamp

(strain relief), for house

water line

6

Hex-Head Screw

for Water Line Clamp

5

Water Valve and

Tube Assembly

3

Hex-Head Screw, for

attaching water valve

8

Adhesive-Backed Water Tube

Fasteners, to secure plastic

water tube (4)

4

10

Water Tube Inlet

9

Phillips Head Screws,

for mounting icemaker (2)

Warranty Label

7

ICEMAKER

WARRANTY VERIFICATION

Date Installed

Dealer

11

Icemaker Fill Cup

(side-mounted)

Icemaker

1

In

s

ta

lla

t

io

n

In

s

t

r

u

c

tio

n

s

12

Hose Clamp

Installation Instructions

PARTS REQUIRED THAT CAME WITH THE REFRIGERATOR

If the fill tube has been misplaced,

call 1.800.626.2002 and order part WR02X11712.

Fill Tube with Foil

(5/8″ O.D.)

3

Installation Instructions

BEFORE YOU BEGIN

Read each step thoroughly before proceeding.

•

CAUTION – Unplug the

Refrigerator. To eliminate the danger

of electric shock during installation,

you must unplug the refrigerator from

its electrical outlet.

Flat blade and Phillips

screwdrivers

Pliers

TOOLS YOU WILL NEED

Sharp knife

INSTALL FILL TUBE

• Slide the fill tube shipped

with the refrigerator onto the

water tube inlet (10). If the fill

tube has been misplaced, call

1.800.626.2002 and order part

WR02X11712.

• Go to the back of the refrigerator.

Remove the label covering the

hole. Pull out the insulation plug

and any debris.

• On the tube side of the water

tube inlet (10), there is an

adhesive backing. Remove the

adhesive backing and slide the

tube into the hole at the back

of the refrigerator. Firmly press

on the inlet to secure it to the

refrigerator.

2

10

PREPARE FOR INSTALLATION (cont.)

• Inside the freezer, remove the two small white

plug buttons (on some models) from the side

wall. (If screws are present instead of plugs,

leave them in place.)

• Remove and discard

the large white plug

from the rear freezer

wall. Pull out the gray

insulation plug and

remove any debris.

• Remove the outlet

cover with a flat-blade

screwdriver.

3

Power

Switch

1

SET POWER SWITCH TO O (off)

Set the icemaker power switch to O (off). Leave

the power switch in the O (off) position until the

refrigerator is connected to the water supply to

prevent premature operation.

Outlet

cover

Remove side wall plug

buttons or leave screws

in place

Rear wall

plug button

Insulation

plug

PREPARE FOR INSTALLATION

• Remove the storage

basket (on some models)

by pulling it out to the

stop position and lifting

it up and out.

Note: After removing

the basket, push the

extension arms back

into the freezer

compartment.

• Remove the chiller shelf

(on some models) by

pulling it straight out.

• Remove the ice bucket

by pulling it out and

lifting it up and out.

• Remove the center

vertical shelf support

(on some models) by

lifting it and rotating

its bottom to the right.

1