GE Monogram ZTD910SFSS Dimension Manual

GE Monogram® 30" Warming Drawer

OVERALL DIMENSIONS

30" (76.2)

25 19/32" (65)

handle width

ZTD910SFSS

1 3/32"

(2.8)

SPECIFICATIONS

Overall Width 30" (76.2 cm)

Overall Height 10 1/2" (26.7 cm)

Overall Depth 23 1/4" (59.0 cm)

Drawer Capacity 1.90 cu. ft. (53.8 l)

Cut-out Width 28 1/2" (72.4 cm)

Cut-out Height 9 1/4" (23.5 cm)

Cut-out Depth 23 1/2" (59.7 cm)

Power Cord Length 56" (142.2 cm)

Electrical Rating 450W @ 120V/60Hz

Total Amps 15 Amps

Net Weight 59 lbs. (26.8 kg)

Approx. Shipping Weight 65 lbs. (29.6 kg)

OPTIONAL ACCESSORIES

Custom Panel Kit ZXD30B

9 1/4"

(23.5)

cutout height

5/8"

(1.6)

28 1/2" (72.4)

cutout width

FRONT VIEW (SHOWING CUTOUT OVERLAP)

27 15/16" (71.0)

23 1/4"

(59.0)

10 1/2"

(26.7)

Professional Panel Kit ZXD30P

ATTENTION ELECTRICIAN:

This appliance is supplied with a 56" (142.2 cm)
long electrical cord equipped with a 3-prong
(grounding) plug that mates to a standard
3-prong grounding wall outlet.

The electrical power cord is located on the right
side of the warming drawer. Locate the wall
outlet within easy reach of the electrical cord in
an adjacent cabinet, within 42" (106.7 cm) of the
right side or 16" (40.6 cm) from the left side of the
cut-out. A recessed outlet can be installed on the
right side of the cut-out, 7" (17.8 cm) max. from
the rear of the cabinet.

DO NOT USE AN EXTENSION CORD
WITH THIS PRODUCT.

For more details refer to the installation instructions
for this product.

2"

(5.1)

Dimensions in parentheses
are in centimeters unless
otherwise noted. Actual
product dimensions may
vary due to manufacturing
tolerances.

TOP VIEW

including handle

SIDE VIEW

26" (66.0)

23 1/4" (59.0)22" (55.9)

29/32"

(2.4)

9"

(22.9)

Product Specification Created 8/14

GE Monogram® 30" Warming Drawer ZTD910SFSS

SIDE VIEW FRONT VIEW

28 1/2" (72.4)

min. cutout width

2" (5.1)

min.

23 1/2"

(59.7)

min. cutout depth

1" (2.5) min.

above toe-kick

or adjust to
oven height

9 1/4"

(23.5)

cutout height

TOP VIEW

Side cleats

ZDT910SFSS

INSTALLATION BELOW SINGLE OR DOUBLE WALL OVEN

ZDT910SFSS

A

2" (5.1)

min.

9 1/4"

(23.5)

cutout height

B

D

TOP VIEW

Side cleats

C

28 1/2" (72.4)

min. cutout width

NOTES

A

Warming drawers

are approved for
installation below
only certain specified
wall oven and cooktop
models. See the label
attached to the top of
the warming drawer for
approved combinations.

B

Additional clearance

between cut-outs may
be required. Check to be
sure that oven supports
above the warming
drawer location do not
obstruct the required
interior 23-1/2" depth
and 9-1/4" height.

C

If you are installing in

frameless cabinets,
it may be necessary
to install 1/2" wide

C

cleats to accept drawer
mounting screws. See
drawer for mounting
screw locations.

1" (2.5) min.

above toe-kick

or adjust to
oven height

INSTALLATION BELOW COOKTOP

From top of countertop

5 1/2"

to top of warming

(14.0)

drawer cutout

min.

9 1/4"

(23.5)

cutout height

1" (2.5) min.

above toe-kick

or adjust to

cooktop height

23 1/2" (59.7)

min. cutout depth

SIDE VIEW FRONT VIEW

D

28 1/2" (72.4)

min. cutout width

23 1/2" (59.7)

min. cutout depth

E

SIDE VIEW FRONT VIEW

D

Install a 2"x2" or 2"x4"

Anti-tip block against
rear wall, 9" from floor
of cutout to bottom
of block. The anti-tip
block must be installed
to prevent the drawer
from tipping forward
when opened and
loaded. Failure to add
the anti-tip block could
result in personal injury.

E

When installing the

warming drawer
below a cooktop, a
solid barrier must be
installed at least 1"
from the lowest point of
the bottom of cooktop
burner box to the top
of the cut-out. Use any

C

solid material such as
1/4" thick plywood.
Allow at least 1/4"
air gap between the
barrier and the top of
the warming drawer.

For more details refer
to the installation
instructions for this
product.

Product Specification Created 8/14

GE Monogram® 30" Warming Drawer ZTD910SFSS

SIDE VIEW

FRONT VIEW

TOP VIEW

28 1/2" (72.4)

min. cutout width

23 1/2" (59.7)

min. cutout width

1/4"

(.6)

min.

1"

(2.5)

min.

Above

toe-kick

2" (5.1) min.

Between cut-outs

Side cleats

9 1/4"

(23.5)

Cut-out

height

ZDT910SFSS

SIDE VIEW

FRONT VIEW

TOP VIEW

28 1/2" (72.4)

min. cutout width

23 1/2" (59.7)

min. cutout width

1/4"

(.6)

min.

1"

(2.5)

min.

Above

toe-kick

Side cleats

9 1/4"

(23.5)

Cut-out

height

ZDT910SFSS

INSTALLATION BELOW A CABINET DRAWER

TOP VIEW

ZDT910SFSS

1/4"

(.6)

min.

B

9 1/4"

(23.5)

Cut-out

height

1"

(2.5)

min.

SIDE BY SIDE INSTALLATION

PROVIDING CABINET SUPPORT INSTALLING ANTI-TIP BLOCKS

23 1/2"

(59.7)

Above

toe-kick

2" (5.1) x 4" (10.2)

or Equivalent Runners

23 1/2" (59.7)

min. cutout width

SIDE VIEW

E

C

D

2" (5.1) min.

Between cut-outs

25" (63.5)
30" (76.2)

2" (5.1) x 4" (10.2)

or

2" (5.1) x 2" (5.1)

Runners or Solid Bottom

Side cleats

A

28 1/2" (72.4)

min. cutout width

FRONT VIEW

A

B

Install

2" (5.1) x 4" (10.2)

or

2" (5.1) x 2" (5.1)

Anti-tip Block against

rear cabinet wall 9" from

floor to bottom of block

NOTES

A

If you are installing in

frameless cabinets,
it may be necessary
to install 1/2" wide
cleats to accept drawer
mounting screws. See
drawer for mounting
screw locations.

B

Install a 2"x2" or 2"x4"

anti-tip block against
rear wall, 9" from floor
of cutout to bottom
of block. The anti-tip
block must be installed
to prevent the drawer
from tipping forward
when opened and
loaded. Failure to add
the anti-tip block could
result in personal injury.

C

When installing the

warming drawer below
a cabinet drawer, a
solid barrier must be
installed at least above
the warming drawer
to block access. Use
any solid material such
as 1/4" thick plywood.
Allow at least 1/4"
air gap between the
barrier and the top of
the warming drawer.
Observe the 5" min.
above the floor or 1"
min. above the toe kick
installation height.

D

When installing two

warming drawers side
by side, install them
in separate cut-outs
and allow a 2" min. gap
between each cut-out.

E

The warming drawer

may be supported by
either a solid bottom or
2"x2" or 2"x4" runners.
The suppor t must
be level and rigidly
mounted, flush with
the bottom edge of the
cut-out (there is no way
to level the drawer once
it has been installed,
so make sure that the
supports are level). The
floor or runners must be
capable of supporting
at least 150 lbs.

For more details refer
to the installation
instructions for this
product.

Product Specification Created 8/14

GE Monogram® 30" Warming Drawer ZTD910SFSS

INSTALLATION WITH CUSTOM PANEL KIT - ZXD27B

30" (76.2)

10 1/2"

(26.7)

Drill

5/16" (0.8)

through custom

panel for lamp jewel

CUSTOM PANEL PREPARATION

FRONT VIEW

1 3/4" (4.5)

23 5/16" (59.2)

including handle

Excluding

custom panel

1 13/16" (4.6)

3/4" (1.9) max.

CUSTOM PANEL

PREPARATION

SIDE VIEW

NOTES

This kit contains a
mounting panel to support
a trim-less custom drawer
front up to 3/4" thick. The
original tubular handle
can be reinstalled onto the
custom panel with longer
screws (not provided) or
can be replaced with a
custom handle of your
choice (also not provided).

For more details refer
to the installation
instructions for this
product.

Drawer

open

Excluding

custom panel

SIDE VIEW

9"

(22.9)

23 1/4" (59.0)24" (61.0)

Product Specification Created 8/14

GE Monogram® 30" Warming Drawer ZTD910SFSS

INSTALLATION WITH PROFESSIONAL STYLE PANEL KIT - ZXD30P

30" (76.2)

26" (66.0)

Handle width

9 1/4"

(23.5)

Cutou-out height

5/8"

(1.6)

FRONT VIEW (SHOWING CUT-OUT OVERLAP)

28 1/2" (72.4)

Cut-out width

27 15/16" (71.0)

2 1/4"

(5.7)

10 1/2"

(26.7)

NOTES

This kit contains a
mounting panel to support
a trim-less custom drawer
front up to 3/4" thick. The
original tubular handle
can be reinstalled onto the
custom panel with longer
screws (not provided) or
can be replaced with a
custom handle of your
choice (also not provided).

For more details refer
to the installation
instructions for this
product.

1 3/4"

(4.5)

2 13/16"

(7.1)

TOP VIEW

28 5/16" (72.0)

Including Handle

28 1/2" (72.4) 23 1/4" (59.0)

SIDE VIEW

23 1/4"

(59.0)

9"

(22.9)

Product Specification Created 8/14

GE Monogram® 30" Warming Drawer ZTD910SFSS

FEATURES AND BENEFITS

Infinite Setting Temperature Control –

75 Degrees to 230 Degrees

Variable Humidity Control – Crisp to Moist

Removable Half Rack

1.9 cu. ft capacity

Accepts 3/4" trimless custom panel and custom
handle with trim kit

Full extension drawer on ball bearing glides

"On" indicator light

Accepts Optional Professional Panel Kit

Removable Stainless Steel Pan

Variable Installation Options

Hidden Controls Provide Flush Installation
Appearance

On/Off Rocker Switch

R

Product Specification Created 8/14