GE Monogram ZICS36NA Dimension Manual

Page 1
Monogram.
Specification Revised 6/00
R
Listed by Underwriters Laboratories
ZICS36NA–GE Monogram 36" Built-In Stainless Steel Bottom Mount
Refrigerator with Automatic Icemaker
Advanced Planning for a Flush or Semi-Flush Enclosure Installation
Monogram built-in refrigerators can be installed flush with typical 24-3/4” deep cabinetry.
When installed semi-flush, the case trim will conceal slight gaps around the enclosure. The refrigerator will project forward approximately 3/4” beyond the front face of surrounding cabinetry.
Side Panels Requirements:
Side panels are not required whenever the refrigerator is installed into an enclosure or between pantry and oven cabinets.
Side panels are required whenever the sides of the refrigerator are exposed.
Side panel sizes vary depending on the type of installation being made.
To accomplish an attractive installation, you must:
1. Determine the need for side panels.
2. Determine side panel thickness.
3. Order matching side panels from the cabinet manufacturer. Be
sure to provide the exact dimensions.
Design Information
True Flush Installation
Semi-Flush Installation
True Flush Installation
In a flush installation,
the refrigerator doors
will align evenly with the front face of adjacent cabinet doors. The refrigerator blends
into the surrounding cabinetry.
Semi-Flush Installation
These refrigerators
can also be installed
semi-flush into an enclosure
using the minimum cutout
width. The case trim creates a
frame around the opening.
0"
3/4"
For answers to your Monogram,
®
GE Profile Performance Series,
GE Profile™or GE appliance questions, call GE Answer Center®service, 800.626.2000.
Page 2
Monogram.
Specification Revised 6/00
For answers to your Monogram,
®
GE Profile Performance Series,
GE Profile™or GE appliance questions, call GE Answer Center®service, 800.626.2000.
R
Listed by Underwriters Laboratories
1/4" Thick
Side Panels
35-1/2"
Finished Dim.
36"
Roughed-In Dim.
Note: 1/4 thick side panels can be inserted into the case trim, making the rough-in the same as the outside trim width, 36”.
ZICS36NA–GE Monogram 36" Built-In Stainless Steel Bottom Mount
Refrigerator with Automatic Icemaker
Design Information Installation Between Base & Wall Cabinets
Cabinet
Refrigerator door
Refrigerator
Cabinet
1/4 Side Panels. Insert end of side panel into trim.
37"
1/2" Thick
Side Panels
36"
Finished Dim.
Roughed-In Dim.
Note: 1/2 thick side panels shown. Side panels can be any thickness. Add side panel thickness to outside trim width (36)to calculate the rough-in dimension. The leading (front) edge must be finished to match surrounding cabinetry.
Refrigerator
Cabinet
Refrigerator door
Cabinet
1/2 To 3/4 Side Panels. Leading Edge Flush With Cabinet.
Installation at End of Run
Side panels, 1/2 minimum thickness are required when using frameless cabinets. The side panel acts as a spacer between the cabinet and the case trim and prevents interference with cabinet door swing. The leading (front) edge must be finished to match surrounding cabinetry.
Frameless Cabinets
Refrigerator
Cabinet
Refrigerator door
1/2 To 3/4 Side Panels. Leading Edge Flush With Cabinet.
Page 3
Monogram.
Specification Revised 6/00
For answers to your Monogram,
®
GE Profile Performance Series,
GE Profile™or GE appliance questions, call GE Answer Center®service, 800.626.2000.
R
Listed by Underwriters Laboratories
ZICS36NA–GE Monogram 36" Built-In Stainless Steel Bottom Mount
Refrigerator with Automatic Icemaker
Dimensions and Specifications (in inches)
4"
24 3/4"
Side View
36" Overall"
35" Case
Front View
26 3/4"
73-1/2"
10 3/4" Max 10" Min
84 1/2" Max* 83 1/2" Min
26"
* 84" Shipping Height. For any other Height Installation
order either ZGCSS36RH (right-hand) or ZGCSS36LH (left-hand).
7"
Wall View
Electrical
Area
84 1/2" max 83 1/2" min
Finished Opening
74" From Floor
to
Bottom
of Electrical
5"
5"
3 1/2"
5"
3 1/2"
Water Supply
24 3/4" Total
Depth
*Finished Width
7 1/2"
*36 Min. for a flush installation.
35-1/2 Min. for a semi-flush installation. Note: Additional cutout width may be required when side panels are used. Add side panel thickness to the finished cutout to calculate rough-in width. See installation examples on the following page.
ZICS36NARH
Handle on the left side, the door swings left to right.
ZICS36NALH
Handle on the right side, the door swings right to left.
These refrigerators are equipped with special hinges that allow the door to swing out and away from the cabinet. No clearances are required on the sides.
When the refrigerator is installed in a corner:
A 4 min. clearance on the hinge side will assure a 90° door opening and access to all drawers.
A 10 clearance on the hinge side is required for removal of pans.
To achieve a flush fit the finished cutout width must be at least 36 wide.
In a semi-flush installation, the finished cutout must be 35-1/2”.
The electrical and water locations must be located as shown for either type of installation.
Page 4
Monogram.
Specification Revised 6/00
R
Listed by Underwriters Laboratories
ZICS36NA–GE Monogram 36" Built-In Stainless Steel Bottom Mount
Refrigerator with Automatic Icemaker
Dimensions and Specifications (in inches)
Trim
84"
23-9/16"
2-9/16"
84"
23-5/16"
2-5/16"
84"
3-3/4"
24-3/4"
Standard 4 high toekick or trim to fit. Height may vary depending on application.
Illustration A
1/4 Side Panels– Insert end of side panel into case trim. Fasten with Velcro strips included.
Illustration B
1/2 to 3/4 Side Panels–Leading edge of side panel is flush with cabinet front. Fasten to the back wall using a cleat.
Illustration C
1/2 to 3/4 Side Panels–Recessed front edge of side panel. Fasten to adjacent cabinets.
Standard 4 high toekick or trim to fit. Height may vary depending on application.
Standard 4 high toekick or trim to fit. Height may vary depending on application.
Side panels are required whenever the sides of the refrigerator will be exposed and when installed between frameless cabinets.
Side panels are not required when the refrigerator is installed into an enclosure.
Side panel installation will be determined by the design of the side panel you have previously chosen.
Side panels must be installed plumb.
If you choose to use 1/4 side panels, they should be
inserted into the case trim as illustrated. Fasten the panels to the refrigerator with velcro strips (provided) before setting refrigerator in place. See illustration A.
1/2 to 3/4 side panels are normally set into place and fastened to adjacent cabinetry or the back wall before rolling the refrigerator into the opening. See illustrations B and C.
These models are factory set for 84 installation height. Adjustments to 83-1/2 or 84-1/2 heights can be made by changing the grille panel.
Order ZGCSS36RH (right hand) or ZGCSS36LH (left hand) Grille Panel Kit. These kits include 2 grille panels, for 83-1/2 and 84-1/2 installation heights.
For answers to your Monogram,
®
GE Profile Performance Series,
GE Profile™or GE appliance questions, call GE Answer Center®service, 800.626.2000.
Page 5
Monogram.
Specification Revised 6/00
ZICS36NA–GE Monogram 36" Built-In Stainless Steel Bottom Mount
Refrigerator with Automatic Icemaker
Features and Benefits
20.8 Cu.Ft. Capacity (Fresh Food
14.1 Cu.Ft./ Freezer 6.7 Cu.Ft.)
Equipped with Factory Installed Automatic Icemaker with Removable Ice Storage Bin
2 Sealed, Adjustable Humidity Slide-Out Vegetable/Fruit Pans
2 Sealed Slide-Out Snack Pans
Adjustable Spill-Proof Glass Shelves
6 Fresh Food Door Shelves (4
Adjustable, 2 with Gallon Storage)
2 Sealed Dairy Compartments
Egg Bin and Glass-Covered Butter Dish
Wine Holder
Slide-Out Freezer Compartment
with 2-Tier Wire Shelves
Stainless Steel Tubular Handles
Model ZICS36NA - Stainless steel
Loading...