GE Monogram ®
36" Bottom Mount
Refrigerators
Custom
Options Guide
and
Installation
Instructions
With Custom Panel Dimensions
and Trim Kit Installation Instructions
These Monogram refrigerators are
designed to be customized with decorator
door and grille panels. Field installed
panels are required.
Factory installed trim will accommodate
1/4" thick custom panels or optional
Lexan ® and stainless steel panel kits.
Optional trim kits allow an even broader
range of custom appearance options.
Read this bo&_t carefully to accomplish the
desired appearance and to insure a troub_ free
instaUation.
This booklet contains information and
illustrations to demonstrate custom
possibilities. Custom door and grille panel
sizes vary to accommodate the kit being
used. Dimensions for each application are
included and can be faxed or sent to the
cabinet manufacturer so that the panels can
be constructed accurately.
Models:
ZIC36N RH
ZIC36N LH
Before you begin - Readthese instructions completely and carefully.
IMPORTANT- Savethese instructions for local inspector's use.
iMPORTANT- OBSERVEALL GOVERNINGCODESAND ORDINANCES.
Note to Installer - Be sure to leave these instructions with the Consumer.
Note to Consumer - Keepthese instructions with your Use and Care Book for future reference.
:t I This appliance musthe properlygrounded.See "Grounding the Refrigerator,"page12.
p_j._l_ Cet appareil dolt_tre correctementmisa la terre.
Consulter. Mise a terre de re_frige_rateerii, page 12.
Ifyou have a question concerning the installation of this
product, call the GEAnswer Center® Consumer
Information Service at 800.626.2000,24hours a day,
7 days a week.
ifyou received a damaged refrigerator, you should
immediately contact your dealer or builder.
Proper installation is the responsibility ofthe installen
Product failure dueto improper installation is not
covered under the GEAppliance Warranty. Seethe
Use & Care Guidefor warranty information.
ForMonogramlocal service in yourarea,
1-800-444-1845.
ForMonogramservice in Canada,
1-888-880-3030
ForMonogramParts andAccessories,call
1-800-626-2002.
• Use this appliance only for its intended purpose,
• Immediately repair or replace electric service
cords that have become frayed or damaged,
• Unplug the refrigerator before cleaning or making
repairs.
• Repairs should be made by a qualified service
technician.
• II nefaat utiliser cet appareil que pour I'usage
pour leqael il a 6t6 constrait,
• II faut rGparer oa remplacer immGdiatement tout
cordon d'alimentation 61ectrique effiloch6 ou
endommag&
• OGbrancher le rGfrigGrateuravant le nettoyage ou
route intervention,
• Les rGparations doivent _tre faites par un
technicien qualifi&
Contents DesignInformation
Flushor Semi-Flush Enclosure Installations ...............................................................................................................................3
Enclosure Cutout and ProductDimensions .................................................................................................................................3
Installation Examples, Between Base & Wall Cabinets ...........................................................................................................4
Installation at End-of-Run ...............................................................................................................................................................4
FramelessCabinets ..........................................................................................................................................................................4
Accessory Panel Kits .......................................................................................................................................................................4
Models Available ..............................................................................................................................................................................5
Advance Planning Exterior Appearance Options .......................................................................................................................5
Trim KitDescriptions ........................................................................................................................................................................6
CustomPanel Dimensions
Product and Cutout Information ....................................................................................................................................................7
1/4"Thick Custom Panels or Panels Secured to 1/4"thick backing ........................................................................................8
3/4"Thick Panels with Supplied Handle, ZKTC36Lor ZKTC36R..............................................................................................9
3/4"Thick Panels with Custom Handle .......................................................................................................................................10
Side Panel or Filler Options ..........................................................................................................................................................11
Installation Instructions..........................................................................................................................................................12-17
TrimKits
ZGC2TrimKit, Grille Panel FrameAdjustment ..........................................................................................................................18
ZKHC1Trim Kit(for 1/4"Panels), Support for Custom Handles.........................................................................................19-21
ZKTC36L/ZKTC36RTrim Kit,3/4"Custom Panels..................................................................................................................22-27
ZKHTClTrim Kit (for 3/4" Panels),Support for Custom Handles ......................................................................................28-31
ZKHCSS1Trim Kit(for 1/4"Panels),Tubular Stainless Steel Handles .............................................................................32-35
ZKHTCSS1Trim Kit(for 3/4" Pane]s),Tabular Stainless Steel Handles ...........................................................................36-38
ZFClTrim Kit, for side to side installation ..................................................................................................................................39
Flush or
Semi-Flush
Enclosure
Installations
Design Information
36" Bottom Mount ReJi_igerators
Advance Planning
f
True FlushInstallation
In a flush installation,
the refrigerator doors
will align evenly with the
front face of adjacent cabinet
doors. The refrigerator blends
into the surrounding cabinetry.
;emi-FlushInstallation
These refrigerators
can also be installed
semi-flush into an enclosure
using the minimum cutout
width. The case trim creates a
frame around the opening.
Monogram built-in refrigerators can be installed flush
with typical 24-3/4"deep cabinetry.
When installed semi-flush, the case trim will conceal
slight gaps around the enclosure. The refrigerator will
project forward approximately 3/4" beyond the front
face of surrounding cabinetry.
In any installation situation, a wide range of appear-
ance options can be accomplished through the use of
one or more trim kits. See trim kit descriptions and
appearance options on page 6.
SidePanels Requirements:
• Side panels are not required whenever the
refrigerator is installed into an enclosure or between
pantry and oven cabinets.
• Side panels are required whenever the sides of the
refrigerator are exposed.
• Side panel sizes vary depending on the type of
installation being made.
Toaccomplishan attractive installation, you must:
1.Determine the need for side panels.
2. Determine side panel thickness.
3. Order matching side panels from the cabinet
manufacturer. Be sure to provide the exact dimen-
sions.
I
Enclosure
Cutout and
Product
Dimensions
• To achieve a flush fit thefinished cutout width must
be at least 36"wide.
• A semi-flush installation requires 35-1/2"rain. finished
cutout width.
• The electrical and water locations must be located as
shown for either type of installation.
83-1/2"Min
_/2" Max
24-3/4'_
36"
841/2"max
831/2"min
Finished
Opening
*FinishedWidth
Electrical
_7 1/_q" / Area
!|
5
-24 3/4"Total
Depth
_ 1/2"
WallView
74"FromFloor
toBottom
ofElectrical
*36" Min. for aflush installation
35-1/2"Min. for a semi-flush installation
Note: Additional cutout width may be required when
side panels are used. Add side panel thickness to the
finished cutout to calculate rough-in width. See
installation examples on the following page.
Design Information
Installation Examples
36" Bottom Mount R@ig_rators
Side panels are required whenever the sides ofthe
refrigerator will be exposed.
1/T to 3/4" side panels are normally set into place and
fastened to adjacent cabinetry orto the back wall
before rolling the refrigerator into the opening.
Therefore, the rough-in dimensions must allow for side
panelthickness. In both aflush and semi-flush
installation, the finished dimension, (thewidth ofthe
opening after side panels are installed), must accom-
modatethe full width of the refrigerator.
See page 11for side panel sizes.
Installation
Between
Base &
WaH Cabinets
FlushandSemi-Flush
Installations
I II1/4"TNckII I
FinishedDim._35-_ /2"_1
Roughed-InDim._36'_
Note: 1/4"thick side panels can be
inserted into the ease trim, making the
rough-in the same as the outside trim
width, 36",
/_tLy
Cabinet
1/4"SidePanelsInsertendof
sidepanelintotrim
Installation
At End-of-Run
FlushandSemi-Flush
II1/TThickII I
. . . 3 _1
FmmhedDml._ 6_,_
Roughed-InRim._37"_
Cabinet
\
\
\
Refrigerator
Cabinet
\
\
\
\
)Refrigeratordoor \
Note: I/2" thick side panels shown. Side panels can
beany thickness, Add side panel thickness to outside
trim width (36")to calculate the rough-in dimension.
The leading (front) edge must befinished to match
surrounding cabinetry.
1/2"To3/4"SidePanelsLeading
EdgeFlushWithCabinet
Framaless
Cabinets
Side panels, 1/2"minimumthickness are required
when using frameless cabinets. The side panel
acts as a spacer between the cabinet and the
case trim and prevents interference with cabinet
door swing. The leading (front} edge must be
finished to match surrounding cabinetry.
1/2"To3/4"SidePanels.Leading
EdgeFlushWithCabinet
\
\
\
RefrigeratorY\
Cabinet \
\
\
\,
Refrigeratordoor\
Accessory
Panel Kits
These refrigerators require field installed door and grille
panels.Thefactory installed trim will accept accessory
panel kits. White or black Lexan® and stainless steel
kits are available. Panels are cut to size and ready to
install. These panel kits must be ordered separately.
ZWBC36,Black Lexan® Panels
ZWWC3g,White Lexan® Panels
ZWSC36,Stainless Steel Panels
Awide range of custom appearance options can be
created with optional trim kits. See page 6for
examples and trim kit descriptions.
4
Models
available
Design Information
36" Bottom Mount Re/_igerator
ZIC36NRH
36"wide model with handle onthe left side,the door
swings left to right.
ZIC36NLH
36"wide model with handle on the right side, the door
swings right to left.
i
Advance
planning
exterior
appearance
options
These refrigerators are designed to be customized with
decorator door and grille panels. Field installed custom
door and grille panels are required for these models.
Factory installed trim will accommodate 1/4"thick
custom panels, Lexan® or stainless steel panel kits.
Door and grille panel sizes vary to accommodate the kit
being used. Sizes are provided in this booklet,
Caution: Maximum panel weight for fresh food door is
50pounds and 30 pounds for freezer drawer panel,
Side panels must be used whenever the sides of the
refrigerator will beexposed. Side panel sizes vary
depending onthe installation.
3/4"thick custom panels-Without trim kits
A raised panel design, screwed or glued to a 1/4"thick
backing can be used. See page 8 for panel sizes and
clearances.
Youshould:
1.Select the appearance option.
2. Order the trim kit for that option.
3. Order the custom door and grille panels from the
cabinet manufacturer. The exact dimension for each
trim kit application is provided inthis booklet. Find
and pull out the page for your application and fax or
send itto the cabinet manufacturer. The cabinet
manufacturer must havethis information to
construct the panels accurately.
4. Determine the final installation situation andorder
matching side panels.
5
Design Information
36" Bottom Mount R@ig_rator
Trim kit
descriptions
ZGC2- Provides 1/4"grille panel frame side pieces for
83-1/2"and 84-1/2"installation heights. The supplied
grille panel frame is factory set for 84".
ZKHCI - Provides the necessary framework to install
custom handles, of your choice, onto 1/4"thick panels.
(Handles not included.)
ZKHCSSI-Tabular stainless steel handles for 1/4"thick
panel installations.
ZKHTC1- Provides the necessary framework to install
custom handles, of your choice, onto 3/4"thick panels.
(Handles not included.) This kit must be used in
combination with ZKTC36Lor ZKTC36R
ZKHTCSS1- Tubular stainless steel handles for 3/4"
thick panel installations. This kit must be used in
combination with ZKTC36Lor ZKTC36R
ZKTC36L(left openingmodels),
ZKTC36R(right openingmodels)- Provides for the
installation of 3/4"thick custom door and grille panels.
This kit provides a standard handle to fit 3/4"thick
panels.
ZFC1TrimKit - For sideto side installation of 2
refrigerators. This kit provides a trim strip to cover the
side case trim for a finished appearance.
1/4"Panelswith standard
handles. No kits required.
1/4"Custompanels with
custom handles. Trim Kit
ZKHC1.
1/4"Custompanels with
TubularStainless Steel
handles, Trim Kit
ZKHCSS1.
3/4"Custom panels with
supplied handle. Trim Kit
ZKTC36L(or ZKTC36R)
_ Custompanels with
custom handles, Trim kits
ZKTC36L (or ZKTC36H)
andZKHTC1,
3/4" Custom panels with
Tubular Stainless Steel
handles, Trim Kits
ZKTC36L(or ZKTC36H)
andZKHTCSSI
6
Custom Panel Dimensions
36" Bottom Mount ReJi_igerators
SideView
243/4"_
_26 3/4"
26"
FrontView 103/4"Max
35"Case_ 10"Min
_6" 0verall'_
841/2"Max
831/2"Min
H/2"
84 1/2" max
83 1/2" min
Finished
Opening
_Finished Width _
Locate Grounded
Electrical outlet
Within Solid
Area Above
Locate Water
Supply Within
the Shaded
_iiii \
1/2"
Wall View
(not to Scale)
74" From
Floor to
Bottom of
Electrical Area
3 1/2"
* 36"Min. for a flush installation into an enclosure.
* 35-1/2"Min. for a semi-flush installation into an enclosure.
Note: Additional cutout width may be required when side panels are
used. Add side panel thickness to the finished cutout width to
calculate rough-in width. See installation examples on page 4.
ZIC36N Bottom Mount Refrigerator
Design Information
Designedto be installed flush orsemi-flush with
surrounding cabinetry. Cutout dimensions, clearances
and side panel sizes are determined bythe many
installation options available. Side panels must be used
whenever the sides of the refrigerator will be exposed.
Side panels are not required when refrigerator is
installed into an enclosure or between pantry andoven
cabinets. IMPORTANT- Side panels, 1/2"minimum
thickness are required when using FRAMELESS
CABINETS.
• Field installed custom panels, Lexan® or stainless
steel panels are required. The door panels and grille
panel sizes vary to accommodate the kit being used.
• The supplied toekick is vented and must remain
unobstructed for proper air circulation.
Optional Panel Kits:
• ZWBC36:Black Lexan® Panel Kit
• ZWWC36:White Lexan® Panel Kit
• ZWSC36:Stainless Steel PanelKit
Optional Custom Trim Kits:
• ZKHCl: For installation of a custom handle of your
choice onto 1/4"Panels.
• ZKTC36Lor ZKTC36R:For installation of 3/4"thick
custom panels.
• ZKHTCI: Forinstallation of a custom handle of your
choice onto 3/4"thick panels. (This kit must be used in
combination with ZKTC36Lor ZKTC36R.
• ZKHCSSI: Tubular Stainless Steel handles for 1/4"
thick panels.
• ZKHTCSSI:Tubular Stainless Steel handles for 3/4"
thick panels.
• ZGC2:1/4"grille panel frame side pieces for 83-1/2
and 84-1/2" installation heights. Factory set height is
84".
Additional Specifications
• A 115volt 6OHz.,15or 20 amp power supply is
required. An individual properly grounded branch
circuit or circuit breskeris recommended. Install a
properly grounded 3-prong electrical receptacle
recessed into the back wall. Electrical must be
located on rear wall as shown.
• Water line can enter opening through the floor or
back wall. The water line should be 1/4"O.D. copper
tubing between the cold water line and water
connection location, long enough to extend to the
front of the refrigerator. Instagation of an easily
accessible shut off valve in the water line is
recommended.
Clearances:
• If the refrigerator is to be installed in a corner:
A 4" clearance is required on the hinge side for a 90°
door opening and access to fresh food drawers. A 10"
clearance is required on the hinge side for removal of
pans.
7
Custom Panel Dimensions
36" Bottom Mount ReJi_igerators
CustomDoorPanel DimensionsUsingStandardTrim
1/4" thick panels
or
Panels secured to 1/4" thick backing
@ 35-1/16 _
Fresh Food Panel 45 1/2"
+
Freezer Panel
35 1/8"
21 11/16"
¢
ZIC36N Bottom Mount Refrigerator
• 1/4"Panels:Cutpanels to size
• Custom handles with 1/4 door panels require Trim kits
ZKHC1orZKHCSSl for tubular stainless steel handles
Standard Trim with Panels secured
to 1/4" thick backing
• Applying a raised panel design to a 1/4"thick backing
(screws or glued): Cut 1/4"thick panels to size On the
fresh food door, fabricate the raised panel to permit at
least 2, fingertip clearance of the standard handle 1-
1/4 clearance from the hinge side to avoid striking
adjacent cabinetry and 5/16 from the top and bottom
edgesto allow for the trim flange For the freezer
drawer, allow 2"clearance at the top handle end and
5/16 clearance on both sides andthe bottom edge to
allow for trim flange
Note: ZKHTCl custom handle kit cannot be used in
this configuration
Custom Grille Panel
35 1/8"
8" 1/4" Thick Panel
The grille panel frame isfactory assembled for 84"
installation height If installation height varies, order
ZGC2trim kit that provides optional side trim pieces
Cut grille panelto sizes shown below
1/4"-
Thick
Backing
Raised Panel on 1/4" Thick Backing
Using Standard Handles
-Appearance
Panel
2anC/_ar_i_tCee2_
5/16" Clearance
Fresh Food Panel
5/16" Clearance •
1-1/4"
Clearance
hinge side
Installation Height PanelHeight
83-1/2' 7-1/2"
84-1/2" 8-1/2"
2" Clearance
Handle End
Freezer Panel
8/16" Clearance
5/16" Clearance
Custom Panel Dimensions
36" Bottom Mount Refrigerator
CustomDoorPanel Dimensions
UsingTrim KitsZKTC36Lor ZKTC36R
3/4" thick panel with kit supplied handle
35-1/16"
ZIS36N Bottom Mount Refrigerator
• TheZKTC36L(or ZKTC36R)trim kit provides for the
installation of 3/4"thick custom door and grille panels,
using the supplied handle. Catpanels to size and
install.
45-9/16"
Fresh Food Panel
+
Freezer Panel
35 4/4"
/
/
2141/16"
Custom Grille Panel
35 1/4"
A 3/4" Thick Panel
J.
Grille Panel height can vary to fill installation
height,
Installation Height Dimension A
83-1/2" 7-3/4"
84" 8-1/4"
84-1/2" 8-3/4"
Important:Maintain 1-1/2"min, gap between
top of door and bottom of grille panel,
Custom Panel Dimensions
36" Bottom Mount Refrigerators
CustomDoorPanel DimensionsUsingStandardTrim
Using Trim Kit ZKTC36L or ZKTC36R
3/4" thick panel
with custom handle
4F 35 1/4 "
Fresh Food Panel 45 9/16"
ZIC36N Bottom Mount Refrigerator
• The ZKTC36L(or ZI(TC36R)trim kit installed together
with aZKHTC1custom handle kit provides for the
installation of 3/4"thick custom door and grille panels
with a custom handle of your choice, Order
ZKHTCSS1for tubular stainless steel handles. Cut
panelsto size, rout the handle side ofthe panels as
shown below and install.
+
Freezer Panel
35 1/4"
1/4"
max
Rout panels to specification below on
the handle side of each panel
1 13/16"
1 13/16"
\
Fresh Food Door Face
Door
Face
Custom Grille Panel
35 1/4"
A 3/4" Thick Panel
&
Grille Panel height can vary to fill installation
height.
Installation Height Dimension A
83-1/2" 7-3/4"
84" 8-1/4"
84-1/2" 8-3/4"
Important:Maintain 1-1/T min. gap between
top of door and bottom of grille panel.
10
Custom Panel Dimensions
36" Bottom Mount Refrigerators
Side Panel or Filler Options
(Notto scale)
Side panelsmast heused whenever the sides ofthe
refrigerator will be exposed.
114"Side Panels
Insertendof
side panel intotrim,
\\\\
84"
_23 9/16"7
Standard4"hightoekick ortrim to fit,
Height may varydependingonapplication.
1/2" to3/4"Side Panels
LeadingEdge
Flushwith Cabinet
Front.The frontor
leadingedge mastbe
finishedto match
cabinetry.
\
84"
_24 3/4"=
Standard4"hightoekick ortrim to fit.
Height mayvarydependingonapplication.
112"to 3/4"Side Panels
Recessedfrontedge.
-23 5/16" q_
84"
25/16"
Standard4"hightoekick or trim tofit.
Heightmayvarydependingonapplication.
11
Installation
36" Bottom Mount R@ig_rator
Tools
Required
• Tinsnips to cut banding
• Stepladder
• 1-1/2"open-end wrench
• Bucket
• Level
• Appliance Hand Truck
• Tubing cutter
• 7/15"open-end wrench
• #2 Phillipsscrewdriver
• Stubby Phillips
screwdriver
• Drill and appropriate bits
• 7/16"socket with 3"
extension for ratchet
• Safety glasses
Materials
Required
Hardware
Supplied
• Water shut-off valve (optional but recommended)
• Water filter WR97XO214(optional but recommended)
• Custom panels for fresh food, freezer drawer, grille
panel
• Side panels
• Hardware for side pane] installation.
• 35"long 2x4for Anti-'tip support
• Special Velcro adhesive strips for 1/4"side panels
• 1/4-1/4union with nuts
• Anti-Tip Mounting Brackets
Flooring
Forproper installation, this refrigerator must be placed
on alevel surface of hard material that is atthe same
height asthe rest of the flooring. This surface should be
strong enough to support afully loaded refrigerator.
NOTE:Protectthe finish ofthe flooring. Cut a large
section of the cardboard carton and place under the
refrigerator where you are working.
Grounding
the
Refrigerator
IMPORTANT- (Please read carefully)
FORPERSONALSAFETY,THISAPPLIANCE MUSTBE
PROPERLYGROUNDED.
The power cord of this appliance is equipped with a
three-prong (grounding) plug which mates with a
standard three-prong (grounding) wall receptacle to
minimize the possibility of electric shock hazard from
this appliance.
Havethe wall outlet and circuit checked bya qualified
electrician to makesure the outlet is properly
grounded.
Where a standard 2-prong wall outlet is encountered, it
is your personal responsibility and obligation to have it
replaced with a properly grounded 3-prong wall outlet.
DO NOT,UNDERANY
CIRCUMSTANCES,CUT
ORREMOVETHETHIRD
(GROUND)PRONG
FROMTHEPOWERCORD.
Useof Adapterplug
Because of potential hazards under certain conditions,
we strongly recommend against use of an adapter plug.
However, if you still elect to use an adapter, where
local codes permit, a TEMPORARYCONNECTION,may
be made to a properly grounded 2-prong wall outlet by
use of a UL listed adapter available at most hardware
stores.
The larger slot in the adapter must be aligned with the
larger slot in the wall outlet to provide proper polarity in
the connection of the power cord.
Attaching the adapter ground terminal to a wall
outlet cover screw does not ground the appliance
unless the cover screw is metal, and not insulated,
andthe wall outlet is grounded through the house
wiring. Youshould have the circuit checked by a
qualified electrician to make sure the outlet is
properly grounded.
FICHED'ADAPTAT]ON
(Fiches d'adaptation non permises au Canada)
When disconnecting the power cord from the adapter,
always hold the adapter in place with one hand and
pulling the power cord with the other hand. If this is not
done,the adapter ground terminal is very likely to break
with repeated use.
Should the adapter ground terminal break, DONOTUSE
the appliance until a proper ground has again been
established.
Useof ExtensionCords
Because of potential safety hazards under certain
conditions, we strongly recommend against the use of
an extension cord. However, if you still elect to use an
extension cord, it is absolutely necessary that it be a UL
listed 3-wire grounding type appliance extension cord
having a grounding type plug and outlet and that the
electrical rating ofthe cord be 15amperes (minimum)
and 120volts.
12
Loading...