GE MONOGRAM ZIC360NR, MONOGRAM ZIC360NRLH, MONOGRAM ZIC360NRRH Dimensions And Installation Information

Page 1
ZIC360NR – GE Monogram 36" Built-In Bottom Freezer Refrigerator
R
6"
Wall View
Electrical
Area
84-1/2" max 83-1/2" min
Finished
Opening
75" From
Floor to
Bottom
of Electrical
Area
10"
5"
3 1/2"
5"
3 1/2"
Water Supply
24" Cutout Depth
35-1/2"
Finished Width
2-5/16"
25"
Min. to
Wall
130
°
130° Door Swing
23-7/8" Behind Frame
36-3/4"
90°
90° Door Swing
4" Min. to Wall
2-5/16"
75" From
Floor to Bottom
of Electrical
Area
84-1/2" max 83-1/2" min
Finished Opening
71-1/2" Finished Width
Electrical
5"
3-1/2"
24" Cutout Depth
Water Supply
Wall View
24-3/16"
26"
6"
10"
10"
Water Supply
26"
5"
3-1/2"
*84" From Floor to Top Frame
35"
Case Width
*83-1/2"
at
Rear
Case Depth: 25-3/8" Framed Models 25-3/4" Stainless Steel Models
Depth Including Handles: 26-7/8" Framed Models 27-3/4" Stainless Steel Models
36" Frame to Frame Width
with Automatic Icemaker
The Installation Space
The finished cutout width must be 35-1/2".
The cutout depth must be 24"
The refrigerator will project forward, slightly beyond adjacent cabinetry, depending on your installation.
The cutout depth beneath a soffit
When installed beneath a soffit, the soffit cannot exceed the 24" installation depth shown. The top case trim overlaps the bottom of the soffit.
Electrical
A 115V, 60Hz., 15 or 20 amp power supply is required.
An individual properly grounded branch circuit or circuit breaker is recommended. Install a properly grounded 3-prong electrical receptacle recessed into the back wall. Electrical must be located on rear wall as shown.
Note: GFI (ground fault interrupter) is not recommended. Water Line
All models are equipped with an automatic icemaker. The water line can enter the opening through the floor or back wall. Route GE SmartConnect Kit or 1/4" O.D. copper tubing between the cold water line and the water connection location at the front of the refrigerator. The installation of an easily accessible shut-off valve in the water line is required.
Product Dimensions
Door Swing Clearances
The installation must allow for clearances to adjacent walls or cabinets. These refrigerators are equipped with a 2-position door stop. The factory-set 130° door swing can be adjusted to 90° if clearance to adjacent cabinets or walls is restricted.
Allow 25" minimum clearances for a full 130° door swing. Allow 15" for pan removal.
• 4" minimum clearance is required when the door swing is adjusted to 90°. If the 90° door stop position is used, pan access is maintained, but pan removal is restricted.
• See door swing illustrations to determine interaction with adjacent cabinets or countertops.
ZUG2, ZUGSS2 Unified Grille Panel Kit
• If you are installing two refrigerators side by side, the installation space must be 71-1/2" wide.
Note: Additional cutout width may be required when side panels are used. Add side panel thickness to the finished cutout to calculate rough-in width.
• The water and electrical locations for each product must be located as shown.
• A separate 115V, 60Hz., 15 or 20 amp power supply is recommended for each product.
* Shipping Height. The
Specification Created 5/04
110100
refrigerator can be adjusted to fit into a cutout that is 83-1/2" min. to 84-1/2" max. height. The top case trim at the front is 1/2" higher and will overlap upper cabinetr y or soffit. Use leveling legs and wheels for a maximum 1" height adjustment.
Listed by Underwriters Laboratories
For answers to your Monogram,® GE Profile™ or GE appliance questions, visit our website at GEAppliances.com or call GE Answer Center
®
service, 800.626.2000.
Page 2
ZIC360NR – GE Monogram 36" Built-In Bottom Freezer Refrigerator
Standard Door Handle
Framed Panel
Standard Door Handle
3/4" Overlay Panel
1/4" Thick Backer Panel
.10" Thick Spacer Panel
R
with Automatic Icemaker
Customization Basics: Framed or Overlay Panels, Custom Handles and Accessory Kits
These bottom-freezer refrigerators are factory set for a left or right door swing. The door swing is NOT reversible. Choose an RH model with hinge on the right side; the door swings left to right. Choose an LH model with hinge on the left side; the door will swing right to left.
Right-Hand
Door Swing
Trimmed Refrigerators ZIC360NRLH, ZIC360NRRH
Trimmed refrigerators are designed to be customized with decorative panels. Field-installed custom door and grille panels are required.
Framed Panels
You may install 1/4"-thick custom panels from your cabinet manufacturer. The decorative panel or accessory panel slides into the factory-installed trim.
Standard supplied handles shown in 1/4" panel position.
Overlay Panels
You may also choose to install custom overlay panels from your cabinet manufacturer. This design provides a seamless appearance which integrates smoothly with surrounding cabinetry.
Left-Hand
Door Swing
Door Handles
The supplied handles can be adjusted to accommodate both framed or overlay panels. Custom handles of your choice, supplied by your cabinetmaker, can also be installed. If desired, you may order ZKHCSS2 Monogram
Side Panels
Side panels must be used whenever the sides of the refrigerator will be exposed.
Optional Accessory Kits
ZKHCSS2: Monogram Stainless Steel Tubular Handle Kit and Handle Side Trim for custom handles. For use on 3/4" custom panels.
ZUG2: For side-by-side installation of two trimmed bottom-freezer refrigerators. This kit provides for the installation of a unified custom grille panel to span the width of two units using a framed or overlay panel.
ZUGSS2: For side-by-side installation of two stainless steel-wrapped bottom-freezer refrigerators. This kit provides a unified stainless steel grille panel to span the width of two units.
Accessory Panels
White or black acrylic and stainless steel accessory panels are available from your Monogram supplier. Panels are cut to size and ready to install. These panel kits must be ordered separately.
Black White Stainless Steel
ZPBC360 ZPWC360 ZPSC360
®
Stainless Steel Tubular Handle Kit for overlay panels.
Standard supplied handles shown in 3/4" overlay panel position.
Specification Created 5/04
110100
Listed by Underwriters Laboratories
For answers to your Monogram,® GE Profile™ or GE appliance questions, visit our website at GEAppliances.com or call GE Answer Center
®
service, 800.626.2000.
Page 3
ZIC360NR – GE Monogram 36" Built-In Bottom Freezer Refrigerator
1/4"
Panel
Door/Drawer
5/16"
Trim
Reveal
Overlay
Panel
1/4"
Backer
Panel
Door/Drawer
.10"
Spacer
Fresh Food
Panel
Freezer Drawer
Panel
D
C
A
B
Grille Panel
Spacer Panel
Overlay Panel
Backer Panel
A
B
Grille Panel
R
with Automatic Icemaker
1/4" Framed Panel Dimensions 3/4" Overlay Panel Dimensions
If you choose to install framed panels, they must be cut to the dimensions shown. The panels will slide into the frame on the door, drawer and grille.
If the custom panel is less than 1/4" thick, and it fits loosely in the door frame, it can be backed up with a piece of filler material or foam tape to improve the fit.
Important Note: Maximum weight for fresh food panel is 50 pounds, 30 pounds for freezer drawer panel and 11 pounds for the grille panel.
For a more custom appearance, overlay panels may be installed on trimmed models. The overlay panel must be secured to a 1/4"-thick backer panel which slides into the trim. A spacer panel 0.10" thick must be placed between the overlay and backer panel.
.250" + .10" + .750" =
1.100" Total Panel Thickness
Center each panel over the other. Assemble the panels with glue and screws. Screws must be countersunk into the backer panel.
Framed Panel Dimensions (in inches) A (Width) B (Grille Ht.) C (FF Ht.) D (FZ Ht.)
1/4" Framed Panel 33-7/8 8-7/8 46-1/16 21-7/8
3/4" Overlay Panel Dimensions (in inches) A (Width) B (Grille Ht.) C (FF Ht.) D (FZ Ht.)
1/4" Backer Panel 33-7/8 8-7/8 46-1/16 21-7/8 .10" Spacer Panel 32-1/2 7-5/8 44-11/16 20-1/2 3/4" Overlay Panel 34-1/8 9 46-5/16 22
Specification Created 5/04
110100
NOTE : Left-to-right offset is not always equal to top-to-bottom offset.
ZUG2 Grille Panel Dimensions
The ZUG2 Unified Grille Panel Kit will accept a framed or overlay grille panel.
• Assemble the overlay panel in the same manner as the door and drawer panels.
Framed Panel Dimensions A (Width) B (Height)
1/4" Framed Panel 69-7/8" 8-7/8"
Overlay Panel Dimensions A (Width) B (Height)
1/4" Backer Panel 69-7/8" 8-7/8" .10" Spacer Panel 68-1/2" 7-5/8" 3/4" Overlay Panel 70-1/8" 9"
For answers to your Monogram,® GE Profile™ or
Listed by Underwriters Laboratories
GE appliance questions, visit our website at GEAppliances.com or call GE Answer Center
®
service, 800.626.2000.
Page 4
1/4"
1/2"
3/4"
1"
1-1/4"
1"
3/4" Overlay
Panel
(Nominal Size)
Stainless Ste
e
l
1/4"
1/2"
3/4"
2"
1-1/4"
1-1/2"
1-3/4"
3"
2-1/4"
2-1/2"
2-3/4"
1/4"
1/2"
3/4"
Door
23-7/8" From
Rear of
Refrigerator
1"
Refrigerator
Case Trim
R
ZIC360NM – GE Monogram 36" Built-In Bottom Freezer Refrigerator
with Automatic Icemaker
Advance Planning for Built-In Custom Bottom-Freezer Refrigerators
Use this page to determine door swing interaction with adjacent cabinets or countertops.
Frameless Cabinets: The case trim overlaps cabinets at the top and sides. Therefore, frameless cabinets may require filler strips to prevent interference with cabinet door swing. The opening must allow for filler strips.
Top View 130° Door Swing (Optional setting) Scale 1:1
Listed by Underwriters Laboratories
For answers to your Monogram,® GE Profile™ or GE appliance questions, visit our website at GEAppliances.com or call GE Answer Center
Specification Created 5/04
110100
®
service, 800.626.2000.
Page 5
1/4"
1/2"
3/4"
1"
1-1/4"
1/4"
1/2"
3/4"
1"
1-1/4"
1-1/2"
23-7/8"
From Rear of
Refrigerator
3/4" Overlay
Panel
(Nominal Size)
Case Trim
Refrigerator
Door
Stainless Steel
ZIC360NM – GE Monogram 36" Built-In Bottom Freezer Refrigerator
R
with Automatic Icemaker
Advance Planning for Built-In Custom Bottom-Freezer Refrigerators
Use this page to determine door swing interaction with adjacent cabinets or countertops.
Frameless Cabinets: The case trim overlaps cabinets at the top and sides. Therefore, frameless cabinets may require filler strips to prevent interference with cabinet door swing. The opening must allow for filler strips.
Top View 90° Door Swing (Optional setting) Scale 1:1
Listed by Underwriters Laboratories
For answers to your Monogram,® GE Profile™ or GE appliance questions, visit our website at GEAppliances.com or call GE Answer Center
®
service, 800.626.2000.
Specification Created 5/04
110100
Page 6
ZIC360NR – GE Monogram 36" Built-In Bottom Freezer Refrigerator
with Automatic Icemaker
Features and Benefits
• 20.6 Cu. Ft. Capacity
• Upfront electronic controls with digital readout
• Multi-shelf air management tower
• 2 Sealed, adjustable humidity vegetable/fruit pans with
easy access lids and full extension slides
• 2 Sealed deli pans with full extension slides
• Adjustable spillproof glass cabinet shelves
• Slide-out freezer compartment with full
extension slides
• Model ZIC360NRRH – Right-handed door swing
(Door panels required)
• Model ZIC360NRLH – Left-handed door swing
(Door panels required)
Specification Created 5/04
110100
Loading...