GE Monogram ZIBS240 Owner's Manual

Download

Page 1

Bar Refrigerator

with Icem(]ker

ZIBI240 ZIBS240

monogram.com

Page 2

Consumer Inform(]tion

Bar Refrigerator wRh tcemaker

Introduction

Contents

Before using gour

bar refrigerator

with icemoker

Your new Monogram bar refrigerator with icemaker makes an eloquent statement of stgle, convenience and kitchen planning flexibilitg. Whether gou chose it for its puritg of design or the assiduous attention to detail, gou will find that gour Monogram bar refrigerator with

icemaker's superior blend of form and function will delight gou for gears to come.

The information on the following pages will help gou operate and maintain gour bar

refrigerator with icemaker properlg. If gou have ang other questions, visit our Website at: monogram.cam

Cure and Cleaning .................. 11, 12

Consumer Services .................... 19

Controls and Features ............... 8-10

Model and Serial Numbers ............... 2

Problem Solver ..................... 13-15

Read this manual carefullg. It is intended to help gou operate and maintain gour new bar refrigerator with icemaker properlg.

Keep it handg for answers to gour

questions.

Product Registration .................... 2

Repair Service ....................... 3, 19

Safety Instructions .................... 4-7

Warranty ..................... Buck Cover

If gou don't understand something or need more help, there is a list of toil-free

consumer service numbers included in

the buck section of this manual.

Visit our Website at: monogram.cam

Write down the

model &

serial

numbers

You will find them on a label on the ceiling

inside the bur refrigerator with icemuker.

Please write these numbers here:

Model Number

Serial Number Use these numbers in ang correspondence

or service culls concerning gour bur refrigerator with icemuker.

Page 3

Consumer Information

Bar Refrigerator wi_h tcemaker

If bfou received a damaged appliance

Save time & money

Remove

packaging

If btou need

service

The warranty does not cover damage caused after delivery.

Before you request service, check the Problem Solver in the back of this manual.

Before using, be sure all packing materials

and tape have been removed. To assure no damage is done to the finish

of the product, the safest way to remove the adhesive left from packaging tape on

To obtain service, see the Consumer Services page in the back of this manual.

We are proud of our service and want you to be pleased. If for some reason you are

not happy with the service you receive, here are steps to follow for further help.

For customers in the USA:

Immediately contact the dealer (or builder)

that sold you the bar refrigerator with

icemaker.

It lists causes of minor operating problems

that you can correct yourself.

new appliances is an application of household liquid detergent. Apply with a soft cloth and allow to soak. Wipe dry and then apply an appliance polish to

thoroughly clean and protect the surface.

For customers in Canada: FIRST,contact the people who serviced your

appliance. Explain why you are not pleased. In most cases, this will solve the problem.

NEXT, if you are still not pleased, write all the details-including your phone

number to:

After

installation is completed

FIRST,contact the people who serviced your

appliance. Explain why you are not pleased.

In most cases, this will solve the problem. NEXT, if you are still not pleased, write

all the details-including your phone

number-to:

Manager, Customer Relations GE Appliances Appliance Park

Louisville, KV 40225

Promptly inspect your new Monogram bar refrigerator with icemaker. If it has been damaged, contact the Installer or Dealer immediately.

This bar refrigerator with icemaker must be properly leveled to ensure correct door alignment, door closure and ice production.

Contact the Installer if the unit is not level. The unit should be centered in

the opening. In a standard 24" opening, the front face of the Stainless Steel door

will be flush with adjacent cabinetry. The front face of the Custom Panel door should

be 1¾" forward of adjacent cabinetry. Contact the installer if clearance is not

correct.

Manager, Consumer Relations Plabe Canada Inc.

1 Factory Lane, Suite 310 moncton, N.B. E1C 9k13

o Test the door swing. Carefully open and

close the door. The door should not rub or catch on adjacent cabinetry. Notify

the installer if the door makes contact with cabinetry.

Please Contact the Installer or Dealer if you experience any of these problems.

Your custom panel (ZIBt240 model only) bar

refrigerator with icemaker is shipped with

two toekicks, a stainless steel and a black toekick. For shipping purposes, one of the

toekicks will be secured to the back or on the inside of the unit, and the second will

be installed on the unit. Keep the unused

toekick and other unused or removed

parts for possible future use.

Page 4

IMPORTANTSAFETYINSTRUCTIONS

READ AND SAVE THESE INSTRUCTIONS

WARN iNG when using this

appliance, alwags exercise basic safetg

precautions, including the following: oUse this appliance only for its intended

purpose as described in this Owner's Manual.

oThis bur refrigerator with icemuker must

be properly installed in accordance with

the Installation Instructions before it is

used.

®Do not allow children to climb, stand

or hung on the shelves in the bur refrigerator with icemuker. The U could damage the bar refrigerator with icemaker and seriously injure themselves.

®Do not store or use gasoline or other

flammable vapors end liquids in the

vicinitg of this or ang other appliance.

®Keep fingers out of the "pinch point"

areas: clearances between the door and between the door and cabinet are

necessarily small. Be careful closing the door when children are in the area.

o Unplug gour bur refrigerator with

icemuker before cleaning or making repairs. NOTE: We strongly recommend that any servicing be performed by a qualified individual.

o Before replacing u burned-out light bulb,

the bar refrigerator with icemaker should be turned OFF or unplugged in order to

avoid contact with a live wire filament. (A burned-out light bulb may break

when being replaced.)

®In bur refrigerators with automatic

icemukers, avoid contact with the moving parts of the ejector mechanism, or with the heating element located on the

bottom of the icemaker.

Do not piece fingers or hands on the automatic icemuking mechanism while the unit is plugged in.

DANGER: R!SK OF CHILD ENTRAPMENT

Child entrapment and suffocation are not problems of the past. Junked or abandoned refrigeration products are still dangerous...even if theg will sit for "just a few dags." If gou ore getting rid of

gour old appliance, please follow these instructions to help prevent accidents.

Before You Throw Awag Your Old Refrigeration Product:

°Take off the doors. o Leave the shelves in place so that children

mug not easilg climb inside.

REFRIGERANTS

All refrigeration products contain

refrigerants, which under federal law must be removed prior to product disposal.

If gou are getting rid of an old refrigeration product, check with the compang handling

the disposal about what to do.

Page 5

IMPORTANTES INSTRUCTIONS DE SI:CURITI

LIREETCONSERVERCESINSTRUCTIONS

AVERTISSEMENT--

Lorsque vous utilisez I'appareil, observez

toujours certaines pr@cautions de base,

notamment :

• N'utilisez I'appareil que pour son usage pr@vu, comme d@crit dans le pr@sent

manuel. Installez le r@frig@rateur de bar avec

machine 6 glaqons conform@ment aux directives d'installation event

de I'utiliser.

• Ne laissez pas les enfants grimper, s'asseoir, se tenir debout ni se pendre aux clagettes du r@frig@rateur de bar avec machine 6 glaqons. IIs pourraient endommager le r@frig@rateur de bar avec machine (_glagons et se blesser gravement.

• N'entreposez et n'utilisez pas d'essence ou autres vapeurs et liquides inflammables 6 proximit@ de cet appareil ou de tout autre appareil @lectrom@nager.

• I_loignez les doigts des parties du r@frig@rateur o5 I°on peut facilement se pincer : les espaces entre les portes et entre les portes et les placards sont toujours @troits. Sogez prudent Iorsque vous fermez les portes de I'appareil en pr@sence des enfants.

• D@branchez votre r@frig@rateur de bar avec machine 6 glaqons event de le nettoger et de le r@parer. REMAROUE :

Nous vous recommandons vivement de

confier toute r@paration (_un technicien qualifi@.

• Avant de remplacer une ampoule grill@e, le r@frig@rateur de bar avec machine (_ glagons dolt @tred@branch@ afin d'@viter

tout contact avec un fil sous tension. (Une ampoule grill@e peut se briser

pendant I'op@ration).

• Dens les r@frig@rateurs de bar qui ont une machine 6 glaqons automatique, _vitez de toucher les pi_ces mobiles du m_canisme d'_jection ou I'_l_ment

chauffant situ_ en bas de la machine

(_glagons.

Ne mettezjamais vos doigts ou vos

mains sur le m@canisme de machine 6 glaqons automatique quand votre

r@frig@rateur est branch@.

DANGERI.

,J ,J

RISQUESPOUR LESENFANTS

Les enfants pris au pi_ge ou morts

d'asphgxie sont toujours d'actualit&

Les appareils de r6frig6ration abandon6s sont toujours aussi dangereux, m_me si on n'attend que "quelque jours" pour

s'en d6barasser. Si vous ne gardez pos

votre ancien appareiI, veuillez suivre

Ies directives cPdessous afin de pr6venir

Ies accidents.

REFRIGERANTS

Tousles appareils de r_frig_ration contiennent des refrigerants qui,

conform_ment aux lois f_d_rales, doivent _tre enlev_s avant route

_limination de I'appareil.

Avant de vous d@barasser de votre vieu×

appareil de r@frig@ration : ®D6montez Ies portes.

®Laissez Ies clagettes en place afin

d'emp_cher Ies enfonts de grimper 6 I'int6rieur.

Si vous vous d@barrassez de vieux appareils de r@frig@ration, v@rifiez,

aupr@s de la soci@t@qui s'occupe de leur @limination, ce que vous devez faire.

Page 6

IMPORTANTSAFETYINSTRUCTIONS

HOW TO CONNECTELECTRICITY

Do not, under any circumstances, cut or remove the third (groundJ prong from

the power cord. For personal safety, this appliance must be properly grounded.

The power cord of this appliance is equipped with a 3@rang (grounding) plug which mates with a standard 3@rang (grounding) wail outlet

to minimize the possibility of electric shock

hazard from this appliance.

Have the wail outlet and circuit checked

bg a qualified electrician to make sure the outlet is properlg grounded.

Where a standard 2-prong wall outlet is encountered, it is gour personal responsibilitg

and obligation to have it replaced with a properlg grounded 3-prong wail outlet.

Use of a GFI (Ground Fault Interrupter) is not

recommended for the bar refrigerator with

icemaker. The appliance should alwags be plugged into

its own individual electrical outlet which has o voltage rating that matches the rating

plate. This provides the best performance and also prevents overloading house wiring

circuits which could cause a fire hazard from overheated wires.

DO NOT USEAN ADAPTER PLUG TO CONNECT THE BAR

REFRIGERATORWITH ICEMAKER TO A 2oPRONG OUTLET.

DO NOT USEAN EXTENSION CORD WITH THIS APPLIANCE.

Never unplug an appliance bg pulling on

the power cord. Alwags grip the plug firmlg

and pull straight out from the outlet. Repair or replace immediatelg all power

cords that have become fraged or otherwise damaged. Do not use a cord that shows

cracks or abrasion damage along its length or at either end.

When moving the appliance, be careful

not to roll over or damage the power cord.

SAVE THESE INSTRUCTIONS

Page 7

IMPO ANTESINSTRUCTIONSDESI'CURITE"

RACCORDEPIENT ELECTRIQUE

Ne coupez ni retirez en aucun cas

la troisi_me broche (mise @la terre} de la fiche du cordon d'alimentation°

Pour votre s_curit_, cet appareil dolt @tre correctement mis 6 la terre.

Le cordon d'alimentation de cet appareiI est muni d'une fiche 6 3 broches (mise

6 Ia terre) qui se branche dans une prise

mural ordinaire 6 3 alv6oles (mise 6 Ia terre)

pour r6duire au minimum Ies risques du chocs 6Iectriques.

Faites examiner Ia prise de courant et

Ie circuit par un 6Iectricien qualifi6 pour vous assurer que Ia prise est correctement

mise 6 Ia terre. Si la prise murale est du tgpe standard

6 2 alv6oles, il vous incombe de la faire

remplacer par une prise 6 3 alv6oles correctement raise 6 Ia terre.

L'appareiI doit toujours _tre branch6 dans sa propre prise de courant, dont la tension

nominale est identique 6 celIe indiqu6e sur

Ia plaque signaI6tique.

L'utilisation d'un disjoncteur de fuite 6 la terre est recommand6e pour Ie r6frig@ateur de

bar avec machine 6 glaqons. Cette pr6caution est recommand6e pour

garantir un rendement optimum et 6viter

une surcharge des circuits 61ectriques de

Ia r6sidence, ce qui pourrait cr6er un risque d'incendie par surschauffe des ills.

N'UTILISEZ JAMAIS UNE PRISE,_ ADAPTATEUR

POUR LE REFRIGERATEUR DE BAR AVEC MACHINE A GLAqONS A UNE PRISE

BIPOLAIRE. N'UTILISEZ JAMAIS DE

RALLONGE AVEC CET APPAREIL.

Ne d6branchezjamais I'appareil en tirant Ie cordon d'alimentation. Saisissez

fermement Ia fiche du cordon et tirez droit

pour Ia retirer de Ia prise. R6parez ou remplacez imm6diatement tout

cordon effiloch6 ou endommag6. N'utilisez pas un cordon fendilI6 ou pr6sentant des

signes d'usure. Lorsque vous d6placez I'appareiI, faites

attention de ne pas la faire rouler sur Ie cordon d'alimentation afin de ne pas I'endommager.

CONSERVEZ CESDIRECTIVES

Page 8

Controls and Features

Bar Refrigerator with tcemaker

Temperature control

Child control

lockout

The temperature display shows the actual temperature of the bar refrigerator with

icemaker. The actual temperature may vary slightlg from the set temperature based on factors such as door openings, amount of

food and room temperature. To change the temperature setting,

press the WARMER or COLDER pads until

you reach the desired set temperature. After 5 seconds, the display will return to the actual temperature.

After making adjustments, allow 12 to 24

hours for the bar refrigerator with icemaker to reach the temperature you have set and

before making any further adjustments.

This child control lockout feature prevents

unwanted changes to your temperature

settings.

TEM_ CONTROL

WARMER COLDER

NOTE:The icemaker temperature is not displayed.

Temperature Settings

Minimum: 34°F (1.1°C} Maximum: 45°F (7.2°C}

After the desired temperature is set, the temperature can be locked. To lock, press both the + and - pads at the same

time for five seconds. To unlock, press both + and - pads for five seconds.

Unit ON/OFF This pad stops cooling in the bur refrigerator

with icemaker, turns off the temperature controls and removes power to the light circuit.

NOTE: The icemaker is on a separate on/off switch. To remove power from the icemaker

See Automatic Icemaker section.

Press this pad for a minimum of 3 seconds to turn the bar refrigerator with icemaker on or off, or unplug the unit for long vacations or absences, or when cleaning the unit or

changing the light bulb.

Glass

shelves

Tempered glass shelves in the bar

refrigerator with icemaker are removable for easy cleaning or for storing larger items.

To remove a shelf, open the door completelg to avoid potential damage to

the gasket. Lift up on the back of the shelf slightlg. Tilt the shelf to one side at an angle

while pulling forward.

Appearance may vary

To replace a shelf, open the door completelg to avoid potential damage to the gasket. Tilt

the shelf to one side at an angle and slide toward the back wall, placing one side onto

the shelf support. Place the other side onto the opposite shelf support. Ensure rear

locking tabs are engaged. When installed properlg, the shelf will not slide forward

when gentlg pulled.

8 To remove, lift up on the back of the shelf Tilt the shelf at an angle while removing Place in slotswhen replacing the shelf

or replacing

Page 9

Controls and Features

Bar Refrigerator wi_h tcemaker

Automatic

icemaker

The icemaker will produce seven cubes

per cgcle-approximatelg 100-130 cubes

in a 24-hour period, depending on freezer compartment temperature, room

temperature, number of door openings and other use conditions.

If the bar refrigerator with icemaker is operated before the water connection is

made to the water valve, set the icemaker

power switch to 0 (off}. When the unit has been connected to

the water supptg, set the icemaker power switch to 1(onl. The green light will come on.

The icemaker will fill with water when it cools to 15% (-10°C). A newlg installed

bar refrigerator with icemaker mag take

12 to 24 hours to begin making ice cubes. You will hear a buzzing sound each time

the icemaker fills with water. Throw awag the first few batches of ice

to allow the water line to clear.

Be sure nothing interferes with the sweep of the feeler arm.

If ice is not used frequentlg, old ice cubes

will become cloudg, taste stale and shrink.

If ice cubes get stuck in the icemaker, the green power light will blink. To correct this, set the icemaker power switch

to O (off) and remove the cubes.

Set the icemaker power switch to 1(onl to restart the icemaker.

After the icemaker has been turned

on again, there will be a delag of about

45 minutes before the icemaker resumes

operations.

NOTE: In homes with lower-than-average water pressure, gou may hear the

icemaker cycle multiple times when

making one batch of ice.

Power Switch

_ Icelaker

Ice storage

bin

When the bin fills to the level of the feeler arm, the icemaker will stop producing ice.

It is normal for several cubes to bejoined

together.

To remove, pull the icemaker drawer fullg open and remove the transportable ice storage bin bg lifting up and out.

NOTE: Ice can fall behind the ice storage bin. Prior to replacing the bin, check for ang fallen

ice.

If the ice storage bin is removed from the refrigerator for an extended period of time, we recommend setting the icemaker

power switch to O loft}. To replace, grasp the side of the right side

of the bin with the higher edge so that the angled side is against the drawer front.

Lower the bin into place and close the drawer.

CAUTION: Failure to install properlg could cause potential damage to the icemaker.

Green

Power Light Feeler Arm

The ice storage bin is dishwasher safe, top rack onlg.

Page 10

Controls and Features

Bar Refrigerator with tcemaker

Ice scoop

Loading tips and

suggestions

Removing full extension

drawer

The bar refrigerator with icemaker includes an ice scoop in the ice storage bin. To

maximize ice bin capacity, store the ice scoop as shown. Do NOT wash the ice scoop

in the dishwasher. For cleaning, handwash

in mild soapy water or use the baking soda solution noted in Cleaning the inside section.

The bottom full extension drawer holds five bottles and is loaded with necks facing

the rear. Tall bottles should not be loaded on the bottom drawer because they may

prevent the door from closing.

• Do not block the thermistor, located on the right hand side, just above the top

shelf of the bar refrigerator with icemaker. Blocking the thermistor could impair the air circulation and temperature control.

To remove:

1. Pull the full extension drawer out to

the STOPposition.

2. Push the tab on right drawer guide down

while pulling the tab on left guide up, and

pull the drawer out.

To replace:

1. Push the drawer slide arm back into

the unit.

Bottom drawer arrangement

Tab )ush tab down on right drawer guide, pull tab up on left drawer guide)

Appearance may vary

2. Pull the small slide sub-assembly

completely forward.

3. Insert the sides of the drawer back into the guides.

4. Push until the tabs lock into place.

Interior fan

The interior fan is located in the rear wall of the bar refrigerator with icemaker

and is designed to run continuouslg to help

maintain the proper cooling temperature.

Sub-assembly

To replace, push drawer slide Pullsmall slide sub-assembly arm back into unit completely forward

NOTE: Make sure the tabs on the full

extension drawer guides are fully engaged

before loading any bottles. Pull the drawers

out all the wag to the STOP position and

push back in several times to make sure locking tabs are properly engaged.

In most instances, the interior fan will run

when the door is open. However, it will not

operate when the door is opened during a defrost cgcle.

Page 11

Care and Cleaning

Bar Refrigerator wi_h tcemaker

For your

safety

Gasket

Light bulb replacement

In the event of a power

failure

Turn the bar refrigerator with icemaker OFF or unplug the unit before cleaning, Turn the bar refrigerator with icemaker OFFbg pressing the button on the controi panei a minimum of S seconds until the light turns off.

The main door and icemaker compartment gaskets mag be cleaned with mild soap and water, a baking soda solution or a mild scouring powder. Rinse and drg well after cleaning.

Turn the bar refrigerator with icemaker OFF

before replacing the light bulb.

If the power fails, open the door as infrequenttg as possible to maintain

the temperature.

After cleaning the gaskets, applg a thin

lager of paraffin wax or petroleum jellg to the gaskets. This helps keep the gaskets from sticking and bending out of shape.

To remove the light shield, pull the tab in the bottom center of the shield. Replace with a 25 watt appliance bulb.

Do not store or use gasoline or other flammable vapors and liquids in the vicinitg of this or ang other appliance.

Preparing for vacation

Preparing

to move

For long vacations or absences, remove

food and turn the bar refrigerator with

icemaker OFF. Clean the interior (see

Cleaning the Inside section)

Secure all loose items such as shelves and Be sure the bar refrigerator with icemaker drawers bg taping them securelg in place to stags in an upright position during

prevent damage, moving.

For shorter vacations, remove perishable foods and leave controls at regular settings.

However, if the room temperature is

expected to drop below 60% (16°C), follow the same instructions as for long vacations.

Set the icemaker power switch to the 0 (off)

position and be sure to shut off the water

supplg to the refrigerator.

Page 12

Care and Cleaning

Bar Refrigerator wi_h tcemaker

For your

safety

Cleaning

the outside

Door handles and trim-Clean with a cloth

dampened with soapy water. Dry with a soft cloth.

Keep the outside clean. Wipe with a clean cloth lightly dampened with mild liquid dish detergent. Dry with a clean, soft cloth.

Do not wipe the refrigerator with a soiled dish cloth or wet towel. These mag leave a residue that can damage the finish. Do not use scouring pods, powdered cleaners, bleach or cleaners containing bleach because these

products can scratch and damage the finish.

Stainless Steel--Regularlg clean and polish the stainless steel exterior and handle with

a commerciallg available stainless steel cleaner such as Stainless Steel Magic' M to preserve and protect the fine finish. Stainless Steel magic is available through

GE Parts and Accessories, 800.626.2002 or monogram.com. Order part number

W×lO×lS.

To avoid scratching the fine finish of the stainless steel, wipe in the same direction as the grain when polishing or cleaning ang stainless steel surface. The grain on the bar refrigerator with icemaker door runs top

to bottom.

Do not use appliance wax or polish on

the stainless steel.

Cleaning

the inside

Unplug the bar refrigerator with icemaker

before cleaning. If this is not practical, turn the unit OFF and wring excess moisture out of the cloth or sponge when cleaning around switches, lights or controls.

Usewarm water and baking soda solution- about a tablespoon (15ml)of baking soda to a quart (1liter)of water.Thisboth cleans and neutralizes odors.Thoroughlg rinseand wipe drg.

Warranty does not cover damage due to improper cleaning methods.

Other parts of the bar refrigerator with icemaker-including the door gaskets, drawer, icemaker, ice scoop and glass shelves-can be cleaned the same wag. Only the ice storage bin is dishwasher safe, top rack only.

Avoid cleaning cold glass shelves with hot water because the extreme temperature difference may cause them to break. Handle glass shelves carefully. Rough handling of tempered glass can cause it to shatter.

Page 13

The Problem Solver

Bar Refrigerator with Icemoker

Normal operating

sounds

Newer appliances sound different from older appliances. Modern appliances have more

features and use newer technology.

Oo you hear what I hear? These sounds are normal.

HUMMM...

WHIR!

--WHOOSH...

The new high efficiency compressor may run faster and longer than your old appliance and you may hear a high- pitched hum or pulsating sounds while it is operating.

Sometimes the appliance runs for an extended period, especially when the doors are opened frequently.

You may hear a whooshing sound when the doors close. This is due to pressure equalizing within the appliance.

The cabinet fan runs continuously except when the door is opened.

You may hear the fans spinning at

high speeds. This happens when the appliance is first plugged in, when the door is opened frequently or when a large amount of food is added to the appliance. The fans help maintain desired

temperatures.

If the door is open for over 3 minutes,

you may hear the fans come on in order to cool the light bulbs.

The fans change speeds in order to provide optimal cooling and energy savings.

CLICKS, POPS,

CRACKSend CHIRPS

You may hear clicking, crocking or popping sounds when the appliance cools to the correct temperature or immediately following defrost.

The electronic control board may cause u clicking sound when relays activate to control appliance components.

Expansion and contraction of cooling coils during and after defrost can cause cracking or popping sounds.

After an icemaking cycle, you may hear the ice cubes dropping into the ice bucket.

WATER SOUNDS

The flow of refrigerant through the freezer cooling coils may make a gurgling noise

like boiling water.

Water dropping on the defrost heater can cause a sizzling, popping or buzzing sound during the defrost cycle.

A water dripping noise may occur during the defrost cycle as ice melts from the evaporator and flows into the drain pan.

Closing the door may cause a gurgling sound due to pressure equalization.

Page 14

The Problem Solver

Bar Refrigerator with tcemaker

Questions?

Use this

problem solver!

PROBLEM POSSIBLE CAUSE

APPLIANCE DOES NOT OPERATE

Appliance may be in defrost cycle when compressor motor does not operate for about 30 minutes.

Appliance is so quiet that most of the time you will hear low or no operating noise.

Controls are set to OFF. Press ON/OFF button on control panel for a minimum of 3 seconds.

if interior light is not on, appliance may not be plugged in

at wall outlet. Push the plug completely into the wall outlet. The fuse is blown/circuit breaker istripped. Replace fuse or reset

the breaker.

The appliance is in showroom mode. Unplug it and plug it back in.

VIBRATION OR RATTLING {Slight

vibration is normal.} COMPRESSOR

MOTOR OPERATES FOR LONG PERIODS OR CYCLES ON AND

OFF FREQUENTLY

FRESH FOOD COMPARTMENT TOO WARM

Adjust the leveling legs as shown in the Installation Instructions.

Normal when appliance is first plugged in.Wait 2/4hours for the

appliance to completely cool down. Often occurs when large amounts of food are placed in appliance.

This is normal.

Door left open or package holding door open. Hot weather or frequent door openings. This is normal.

Temperature control set at the coldest setting. See Temperature Control.

Temperature control not set cold enough. See Temperature Control. Allow 12 to 2/4hours for temperature to change.

Warm weather or frequent door openings.

Door left open for long time. Package may be holding door open.

Thermistor may be blocked, which can affect the overall temperature. The thermistor is located on the right hand side just above the top shelf.

FROST OR ICE CRYSTALS ON REAR WALL

Too frequent or too long door openings.

Thermistor may be blocked, which can affect the overall temperature. The thermistor is located on the right hand side just above the top shelf.

AUTOMATIC

ICEMAKER

DOES NOT WORK

Icemaker power switch is in the O Ioffl position.

Water supply turned off or not connected. SeeInstallation Instructions.

Freezer compartment too warm. Allow 2/4hours for the appliance

to completely cool down.

Plied up cubes in storage bin cause icemaker to shut off. Levelcubes in bin.

Ice cubes stuck in icemaker (green power light on the icemaker is

blinking). Turn off the icemaker, remove cubes and turn the icemaker back on.

1/4

Page 15

The Problem Solver

Bar Refrigerator with tcemaker

Questions?

Use this

problem solver!

PROBLEM FREQUENT

"BUZZING" SOUND

ICE CUBES HAVE ODOR/TASTE

SLOW ICE CUBE FREEZING

APPLIANCE HAS ODOR

DOOR NOT CLOSING PROPERLY

MOISTURE FORMS ON OUTSIDE OF

APPLIANCE

POSSIBLE CAUSE

Icemaker power switch is in the 1Ionl position, but the water supply

to the appliance has not been connected or is kinked. Set the power switch to the O Ioffl position. Keeping it in the ! Ion} position will

damage the water valve or straighten the water supply line.

Old cubes need to be discarded.

Ice storage bin needs to be emptied and washed.

Unsealed packages in fresh food compartment may be

transmitting odor/taste to ice cubes.

Interior of appliance needs cleaning. See Care and Cleaning.

Door may have been left open.

interior needs cleaning. SeeCare and Cleaning.

Keepopen box of baking soda in appliance; replace every 3 months. Door gasket is sticking or folding over, Apply petroleum jelly or

paraffin wax to the face of the gasket. The door is hitting an internal component inside the appliance.

Adjust interior components to prevent interference.

Not unusual during periods of high humidity. Wipe surface dry.

Door left open or package holding door open.

MOISTURE COLLECTS INSIDE

INTERIOR LIGHT DOES NOT WORK

HOT AIR FROM BOTTOM OF APPLIANCE

APPLIANCE

NEVER SHUTS OFF BUT TEMPERATURES

ARE OK

ACTUAL TEMPERATURE

NOT EQUAL TO SETTEMPERATURE

TEMPERATURE WILL NOT ADJUST

Too frequent or too long door openings.

In humid weather, air carries moisture into appliance when doors

are opened.

No power at outlet. Light bulb needs replacing. SeeCare and Cleaning.

Normal air flow cooling motor. In the refrigeration process, it is

normal that heat be expelled in the area under the appliance. Some floor coverings are sensitive and will discolor at these safe and normal temperatures.

Adaptive defrost keeps compressor running during door openings. This is normal. The appliance will cycle off after the door remains closed for two hours.

Normal operation in extreme temperatures.

Unit just plugged in.Allow 2/4hours for the system to stabilize. Door open for too long. Allow 24 hours for the system to stabilize.

Warm contents added to appliance. Allow 24 hours for the system to stabilize.

Defrost cycle is in process. Allow 2/4hours for the system to stabilize.

Thermistor may be blocked, which can affect the overall temperature. The thermistor is located on the right hand side just above the

top shelf.

Temperature may be in lockout mode. Press both + and - pads for 5 seconds to unlock the temperature.

Thermistor may be blocked, which can affect the overall temperature. The thermistor is located on the right hand side just above the top shelf.

Page 16

Notes

Bar Refrigerator wi_h tcemaker

Page 17

Notes

Bar Refrigerator wi_h tcemaker

Page 18

Notes

Bar Refrigerator wi_h tcemaker

Page 19

Consumer Services

Bar Refrigerator with tcemoker

With the purchase of gour new Monogram appliance, receive the

assurance that if you ever need information or assistance from GE, we wilt be there. All gou have to do is call--toll-free!

GE Answer

Center ®

In the USA:

800.626.2000

In-Home Repair

Service

in the USA:

800.444.1845 in Canada:

1.800.561.3344

For

Customers

With Special

Needs,.,

Whatever gour question about ang Monogram major appliance, GEAnswer Center® information service is available to help. Your call-and gour question-will be answered promptlg and courteouslg. And gou con call ong time. GEAnswer Center®service is open 24 hours o dog, Mondog through Soturdog.

Visit our Website at: monogram.cam in Canada, call 1.800.561.3344.

AGE consumer service professional will provide expert repair service, scheduled at a time that's convenient for gou. Mang GEConsumer Service compang-operated locations offer gou service todag or tomorrow, or at gour convenience (7:00a.m. to 10:00 p.m. weekdags, 8:00 a.m. to 6:00 p.m. Saturdag and Sundag). Our factorg4rained technicians know gour appliance inside and out-so most repairs can be handled in just one visit. In Canada: Mondag to Fridag, 7:00 a.m. to 8:00 p.m. and Saturdag, 8:00 a.m. to S:00 p.m. EDST.

GEoffers Braille controls for a varietg of GEappliances, and a brochure to assist in planning a barrier-free kitchen for persons with limited mobilitg.

Consumers with impaired hearing or speech who have access to a TDD or a conventional teletgpewdter mag call 800.TDD.GEAC(800.833.4322) to request information or service.

In the USA:

800.626.2000

Service Contracts

In the USA:

800.626.2224 In Canada:

1.800.561.3344

Parts and

Accessories

In the USA:

800.626.2002 In Canada:

1.800.561.3344

SECTIO_ _A

You can hove the secure feeling that GEConsumer Service will still be there after gour warrantg expires. Purchase a GEcontract while gour warrantg is still in effect and gou'll receive a substantial discount. With a multiple-gear contract, gou are assured of future service at todag's prices.

Individuals qualified to service their own appliances can have parts or accessories sent directlg to their home. The GEparts sgstem provides access to over/47,000 parts...and all GEGenuine Renewal

Parts are fullg warranted. VISA,MasterCard and Discover cards are accepted.

User maintenance instructions contained in this manual cover procedures intended to be performed bg ang user. Other servicing generallg should be referred to qualified service personnel. Caution must be exercised, since improper servicing mag cause unsafe operation.

Page 20

Warranty

Bar Refrigerator wi_h tcemaker

YOURMONOGRAMBARREFRIGERATORWtTHICENAKERWARRANTY Staple sales slip or canceled check here. Proof of original

purchase date is needed to obtain service under warranty.

WHAT IS COVERED

From the Date

of the Origina/

Purchase

WHAT tS NOT COVERED

LIMITED ONE-YEAR WARRANTY For one Near from date of origina! purchase we wi!! provide, free of charge parts and service labor in gout home

to repair or replace o%, part of the unit that fails because of a manufacturing defect. LIMITED FIVE-YEAR WARRANTY

For five Nears from date of original purchase, we wi!l provide, free of charge, parts and service labor in gout home to repair or replace anal part of the sea/ed re#igerating s_/stem (the compressor, condenser, evaporator and all connecting tubing} that fails because of a manufacturing defect.

This warrants is extended to the original purchaser and ann succeeding owner for products purchased for ordinarg home use in the 48 mainland states, Hawaii, Washington, D.C.or Canada. If the product is located

in an area where service bg a GEAuthorized Servicer is not available, Sou ma Nbe responsible for a trip charge or Sou maN be required to bring the product to an Authorized GE Service location for service. In Alaska the

warrants is the same except that it is LIMITEDbecause Sou must paNto ship the product to the service shop or for the service technician's travel costs to gout home.

All warrants service wil! be provided bg our Factors Service Centers or bg our authorized Customer Care® servicers during normal working hours.

Should sour appliance need service, during warrants period or begond, in the USAcal! 800.444.1845 In Canada: 800.561.5544. Please have gout serial number and model number available when oalling for service.

Service trips to gout home to teach Sou how

to use the product.

Replacement of house fuses or resetting of circuit breakers.

Damage to the product caused bg accident, fire,

floods or acts of God.

Failure of the product if it is used for other than its intended purpose or used commerciallg.

Damage caused after delivers.

Improper installation, delivers or maintenance.

If Sou have an installation problem, contact sour dealer or installer. You are responsible for providing adequate electrical, plumbing and other connecting facilities.

Replacement of the light bulbs, if included. Loss of food due to spoilage fin the USAonlg}.

Incidental or consequential damage caused bg possible defects with this appliance.

Product not accessible to provide required service.

197D5891PO13 49-60435-1

08-07 JR Printed in SIovenia

EXCLUSION OF IMPLIED WARRANTIES--Your sole end exclusive remedy is product repair us provided in this Limited Warranty. Any implied warranties, including the implied warranties of merchantability or

fitness for a particular purpose, are limited to one year or the shortest period allowed by law.

Some states/provinces do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion maN not applg to SOU.Thiswarrants gives Sou specific legal rights, and SOU

maNalso have other rights which varg from state to state/province to province. To know what gout legal rights are in gout state/province, consult gout Iooal or state/provincial consumer affairs office or gout state's Attorneg

General. Warrantor in USA: General Electric Comports,

Louisville, KY80225

Warrantor in Canada: Nabe Canada Inc.,

Burlington, Ontario

GE Consumer & Industrial Appliances

General Electric Compang Louisville, KY40225

go.cam