GE Monogram ZGU48L6RDSS, Monogram ZGU48N6RWSS, Monogram ZGU48N6RDSS Dimensions And Specifications

Page 1

Monogram.

™

Specification Created 7/01

For answers to your Monogram,® GE Profile™or GE appliance questions, visit our website at GEAppliances.com or call GE Answer Center®service, 800.626.2000.

ZGU48L6RDSS—48" Professional Gas Cooktop

Dimensions and Specifications (in inches)

This cooktop is factory set for liquid propane gas and has 6 gas burners and grill.

Natural Gas Model Also Available:

ZGU48N6RWSS–6 gas burners and grill.

Installation Options:

This cooktop can be installed in standard 24" or deeper 25" cabinets.

• In 24" deep cabinets, the front of the cooktop will project approximately 1-7/8" beyond the front of the countertop.

• In 25" deep cabinets, the cooktop will be flush with the front of the countertop

• The stainless surface of the cooktop will be 1/2" higher than adjacent countertop.

Accessory Requirements:

All models require the installation of a backguard. A backguard should be ordered at the same time as the cooktop. Both should be on site before cabinetry has been installed.

Order one backguard:

ZXC1B48WSS–1-1/2" high backguard (required for island installations) ZXC12B48WSS–12" high backguard ZXC22B48WSS–22" high backguard with warming shelf (2 piece)

26-5/8"

12"

1/2"

8-7/16"

Countertop Level

22-3/4" 23-1/4"

3" to Center Line

of Gas Inlet

2-1/2"

Cabinet Face - Projecting Control Panel

Cabinet Face - Flush Control Panel

1/2"

Low Back

21-1/4"

High Back

ZXC22B48WSS

ZXC12B48WSS

ZXC1B48WSS

1/2" Above Adjacent Countertops.

Front Projects Outward as Shown From Standard Depth Cabinets.

Cooktop

1/2" Above Adjacent Countertops.

Front Flush With Cabinets - a Minimum of 25-3/4" Cabinet Depth Required

Flush With Cabinet Front

Cooktop

Listed by Underwriters Laboratories

Page 2

Monogram.

™

Specification Created 7/01

For answers to your Monogram,® GE Profile™or GE appliance questions, visit our website at GEAppliances.com or call GE Answer Center®service, 800.626.2000.

ZGU48L6RDSS—48" Professional Gas Cooktop

Dimensions and Specifications (in inches)

Advance Planning:

Refer to dimensional drawings for appropriate placement and necessary clearances when planning the installation.

• Cabinetry cannot be installed directly above the cooktop.

• This cooktop requires the installation of a vent hood, 30" to 36" above the surface.

–The vent hood must be at least 24" deep. –The vent hood must be the same width as

the cooktop.

–The vent hood blower should provide at least

800 CFM and up to 1200 CFM. –Choose a vent hood with 800CFM for best performance when operating the grill

• Working areas adjacent to the range should have 18" minimum clearance between countertop and cabinet bottom.

• Clearance between cooktop and side wall or combustible material must be at least 12" on each side.

• This cooktop requires 8" free space below the countertop.

• If the cooktop is installed in an island: –Allow 12" min. clearance at the back to

combustible materials.

–Allow 36" min. above the cooking surface to

combustible materials.

• Installation must conform with local codes. In the absence of local codes, the gas cooktop must comply with the National Fuel Gas Code, ANSI Z223.1, latest edition.

A.G.A. approved

48" Wide Hood

30" Min. 36" Max.

18" Min.

12" Min. to Combustible Material Each Side

36" Min. to Combustible Material From Cooking Surface

13" Max.

17"

22-3/4" Min.

Electric/Gas

Supply

46-1/8"

7/8"

2-1/2"

Cooking Surface

Low Back

High Shelf

26-5/8"

10"

2-1/2"

21-1/4"

12"

36" Min.

to Combustibles

Island Trim

12" Min. to Combustibles Without Backguard

36" Min.

to Combustibles

Listed by Underwriters Laboratories

Page 3

Monogram.

™

Specification Created 7/01

For answers to your Monogram,® GE Profile™or GE appliance questions, visit our website at GEAppliances.com or call GE Answer Center®service, 800.626.2000.

ZGU48L6RDSS—48" Professional Gas Cooktop

Dimensions and Specifications (in inches)

Cutting the Countertop Opening:

Measure carefully when cutting the countertop. Make sure sides of the opening are parallel.

• This Monogram™gas cooktop is designed to fit in 48" or larger base cabinet.

• This cooktop requires 8" free space below the countertop.

• The cooktop is designed to hang from the countertop from its side flanges.

The countertop must be strong enough to support the weight of the cooktop.

• Smooth any rough edges on the countertop before installing.

–Formica countertop edges must be finished.

• Support cleats can be secured to cabinet

sides OR build a support deck or box inside the cabinet which will support the weight of the cooktop.

–Build the support box using a solid material,

cut a 5" x 5" square in the left rear corner for the gas inlet and power cord clearances.

Installation Information:

Before installing, consult installation instructions (Pub. No. 49-8812) packed with product for current dimensional data.

2-1/2"

7/8"

46-5/16"

22-3/4"

26-5/8"

8-7/16"

47-7/8"

Counter Sunk Screws

Adjacent Cabinet and Countertop

17"

Locate gas inlet on back wall or on floor 2" from back wall

16"

Listed by Underwriters Laboratories

Page 4

Monogram.

™

Specification Created 7/01

ZGU48L6RDSS—48" Professional Gas Cooktop

onogram

REA

Features and Benefits

• Stainless Steel Model

• Liquid Propane Gas

• 48” Gas Cooktop

• Six (15,000/500 BTU) Dual-Ring Gas Burners

• 18,000 BTU Grill

• Cast-Iron, Porcelainized Burner Grates

• Stainless Steel, Slide-Out Drip Trays

• Electronic Ignition with Automatic Re-Ignition

• Commercial-Style Controls

• Stainless Steel Grill Cover

• Model ZGU48N6RDSS—Natural Gas

• Model ZGU48L6RDSS—Liquid Propane Gas