Page 1
Installation
Instructions
Free-Standing Side-by-Side
Stainless Steel Refrigerator
ZFSB23D SS
ZFSB25D SS
monogram.com
Page 2
Safety Information
BEFORE YOU BEGIN
Read these instructions completely and carefully.
• IMPORTANT– Save these instructions
for local inspector’s use.
• IMPORTANT – Observe all governing
codes and ordinances.
• Note to Installer – Be sure to leave these
instructions with the Consumer.
• Note to Consumer – Keep these instructions with
your Owner’s Manual for future reference.
WARNING:
This appliance must be properly grounded. See
“Grounding the Refrigerator,” page 4.
AVERTISSEMENT :
Cet appareil doit être correctement mis à la terre.
Consulter « Mise à la terre du réfrigérateur », page 4.
If you received a damaged refrigerator, you should
immediately contact your dealer or builder.
Skill Level – Installation of this refrigerator requires
basic mechanical, carpentry and plumbing skills.
Proper installation is the responsibility of the installer.
Product failure due to improper installation is not
covered under the GE Appliance Warranty. See the
Owner’s Manual for warranty information.
CAUTION:
Due to the weight and size of this refrigerator, and to
reduce the risk of personal injury or damage to the
product – TWO PEOPLE ARE REQUIRED FOR PROPER
INSTALLATION.
PRUDENCE :
À cause du poids et de la taille de ce réfrigérateur et
pour réduire le risque de blessure et de dommages,
IL FAUT DEUX PERSONNES POUR FAIRE L’INSTALLATION
CORRECTEMENT.
WARNING:
• Use this appliance only for its intended purpose.
• Immediately repair or replace electric service cords
that become frayed or damaged.
• Unplug the refrigerator before cleaning or making
repairs.
• Repairs should be made by a qualified service
technician.
AVERTISSEMENT :
• Il ne faut utiliser cet appareil que pour l’utilisation
appropriée.
• Réparer ou remplacer immédiatement tout cordon
électrique effiloché ou endommagé.
• Il faut débrancher le réfrigérateur avant le nettoyage
ou toute intervention.
• Les réparations doivent être faites par un technicien
qualifié.
CONTENTS
Planning Information
Product Dimensions and Clearances............................................3
The Installation Space..........................................................................3
Installation Instructions
Tools, Hardware, Materials ................................................................4
Grounding the Refrigerator ..............................................................4
Step 1, Move Refrigerator Indoors (ZFSB25) ............................5
Step 1A, Move Refrigerator Indoors (ZFSB23) ............................6
Step 2, Install Water Line ..................................................................7
Step 2A, RO Water Line ......................................................................8
For Monogram local service in your area, call
1.800.444.1845.
For Monogram service in Canada, call
1.800.561.3344
For Monogram Parts and Accessories, call
1.800.626.2002.
www.monogram.com
tep 3, Connect W
S
Step 4, Connect Power ........................................................................8
Step 5, Move Refrigerator Into Position ......................................8
tep 6, Lev
S
Step 7, Level Doors ..............................................................................9
Step 8, Screw Down Support Leg ..................................................9
tep 9, Start Icemaker ......................................................................10
S
Step 10, Temperature Controls......................................................10
Step 11, Install Toekick......................................................................10
el Refrigerator ..................................................................9
ater Supply ........................................................8
2
Page 3
Planning Information
36"
72"
29-1/2"
Including
Handles
27-1/2"
Case
Depth
19"
14-1/4"
160° Door Swing
72"
36"
30-1/2"
Including
Handles
28-1/2"
Depth
Wall View
Electrical
Area
73" min.
Water Supply
36-1/4" min.
PRODUCT DIMENSIONS AND CLEARANCES
These Monogram free-standing refrigerators require the
following clearances for proper air circulation, plumbing
and electrical connections.
Air Circulation Clearances:
• 1/8" on each side
• 1" at the top
• 1-1/2" at the back side
THE INSTALLATION SPACE
The opening width must be at least 36-1/4".
ZFSB23
ZFSB25
Installation in a corner:
• Allow 4" clearance on each side to an adjacent wall for a
90° opening and access to drawers.
ALL MODELS
ZFSB25
ZFSB23
• On the freezer side, allow 14-1/4" min. clearance
for removal of ice bin.
On the fresh food side, allow 19" min. clearance
•
all for removal of drawers.
to w
er And Electrical Locations
at
W
The opening must be prepared with the electrical and water
supply located as shown.
Additional Specifications
• A 115 volt 60Hz., 15 or 20 amp power supply is required.
An individual properly grounded branch circuit or circuit
eaker is recommended. Install a properly grounded
br
3-prong electrical receptacle recessed into the back wall.
NO
TE:
ound fault interr
GFI (gr
upter) is not recommended.
• Water line can enter the opening through the floor or
through an adjacent cabinet, as close to the back
wall as possible. The water line should be GE
Smar
tConnect
™
efrigerator T
R
ubing or 1/4" O
. copper
.D
tubing between the cold water line and water connection
location at the rear of the refrigerator. Installation of an
easily accessible shut off valve in the water line is
recommended.
3
Page 4
Installation Instructions
TOOLS REQUIRED
• Tinsnips to cut banding
Stepladder
•
• Bucket
• Level
• Appliance hand truck
• Tubing cutter
• #2 Phillips screwdriver
• Drill and appropriate bits
• 3/8", 5/16" and 7/16" hex socket
• 1/8" Allen wrench
• Safety glasses
MATERIALS REQUIRED
• 1/4" O.D. compression nut and 2 ferrules (sleeves)
OR GE SmartConnect™Refrigerator Tubing Kits
GROUNDING THE REFRIGERATOR
IMPORTANT – (Please read carefully)
FOR PERSONAL SAFETY, THIS APPLIANCE MUST BE
PROPERLY GROUNDED.
The power cord of this appliance is equipped with
a 3-prong (grounding) plug which mates with a
standard 3-prong (grounding) wall receptacle to
minimize the possibility of electric shock hazard
from this appliance.
FLOORING
For proper installation, this refrigerator must be placed on
level surface of hard material that is at the same height
a
as the rest of the flooring. This surface should be strong
enough to support a fully loaded refrigerator.
IMPORTANT NOTE: Protect the finish of the flooring. Cut a
large section of the cardboard carton and place under the
refrigerator where you are working.
DO NOT, UNDER ANY
CIRCUMSTANCES, CUT
OR REMOVE THE THIRD
(GROUND) PRONG
FROM THE POWER CORD.
DO NOT USE AN ADAPTER PLUG TO CONNECT THE
REFRIGERATOR TO A 2-PRONG OUTLET.
Have the wall outlet and circuit checked by a
qualified electrician to make sure the outlet is
properly grounded.
Where a standard 2-prong wall outlet is encountered,
it is your personal responsibility and obligation to
have it replaced with a properly grounded 3-prong
wall outlet.
DO NOT USE AN EXTENSION CORD WITH THIS
APPLIANCE.
4
Page 5
Installation Instructions
Hinge Screws
D
Water Line Coupler
Wire Harness
C
Toekick Screw
B
A
STEP 1 MODEL ZFSB25
(GO TO STEP 1A FOR MODEL ZFSB23)
MOVE REFRIGERATOR INDOORS
IMPORTANT: Doors and passageways into
the installation location require a 31" min. opening. If the
opening is less than 31", the top cap and doors must be
removed.
NOTE: Skip this step if door removal is not required.
See instructions on page 7, “To Move The Refrigerator
Indoors.”
NOTE: To prevent damage, leave inside
packaging, door spacer and outside
protective wrap in place until the unit
is moved to the installation location.
REMOVE THE DOORS
The top cap must be removed to access hinges. It is best
o remove one door at a time.
t
A. Remove 2 screws on top and 2 screws at the back of
the top cap. Lift off top cap.
B. Open both doors. Remove the 2 toekick screws and pull
forward to remove.
C. Disconnect the water line coupler by pushing against
the collar on the left side. Disconnect wire harness.
D. Remove 2 screws holding top hinge to the case.
Carefully lift off door.
Follow the same procedure to remove the fresh food door.
5
Page 6
Installation Instructions
Hinge Screws
E
Water Line Coupler
Wire Harness
D
Toekick Screw
C
B
A
STEP 1A MODEL ZFSB23
MOVE REFRIGERATOR INDOORS
IMPORTANT: Doors and passageways
into the installation location must allow the full depth
of the refrigerator to pass through. ZFSB23 requires
a 31" min. opening. When the opening is less than these
minimum widths, the top cap and doors must be removed.
NOTE: Skip this step if door removal is not required.
See instructions on next page, “To Move The Refrigerator
Indoors.”
NOTE: To prevent damage, leave inside
packaging, door spacer and outside
protective wrap in place until the unit
is moved to the installation location.
REMOVE THE DOORS
The top cap must be removed to access hinges. It is best
o remove one door at a time.
t
A. Remove 2 screws and springs on top of the refrigerator,
one on each side. Push the top cap forward and lift up
from the rear.
B. Remove 2 screws holding the top filler strip, lift off.
C. Open both doors. Remove the 2 toekick screws and pull
forward to remove.
D. Disconnect the water line coupler by pushing against
the collar on the left side. Disconnect wire harness.
E. Remove 2 screws holding top hinge to the case.
Carefully lift off door.
Follow the same procedure to remove the fresh food door.
6
Page 7
Installation Instructions
STEP 1 ALL MODELS (continued)
To move the refrigerator indoors:
Place a piece of the carton or soft cloth against the
•
side panel of the refrigerator to pad and protect the
stainless steel finish.
• Place the refrigerator on the handtruck with a side
against the truck only
• Move the refrigerator indoors.
.
STEP 2 INSTALL WATER LINE
• A cold water supply is required for automatic icemaker
operation. The w
120 p.s.i.
• Route GE SmartConnect™Refrigerator Tubing or 1/4" OD
copper tubing between house cold water line and the
water connection location.
• Measure the distance from the water valve on the back
of the refrigerator to the water supply line. Add 8 foot
length to allow the refrigerator to be moved away from
the wall after installation. Bend the tubing into 3 coils of
about 10".
NOTE: The only GE approved plastic tubing is supplied
in GE SmartConnect™Refrigerator Tubing kits. Do not
use any other plastic water supply line because the line
is under pressure at all times. Certain types of plastic
will crack or rupture with age and cause water damage
to your home.
ater pressure must be between 40 and
REINSTALL DOORS
Refer to the illustration on page 5 or 6.
• Carefully, route the water line tubing and electrical
through the freezer side bottom hinge. Lower the door
nto bottom hinge.
o
• Secure top hinge.
• Insert the tubing all the way into the coupler.
• Reconnect the wiring harness.
• Replace top cap with original screws and springs
(where present).
Follow the same procedure to reinstall the fresh food door.
• Turn on the main water supply and flush debris.
Run about a quart of water through the tubing into a
bucket. Shut off water supply at the shut-off valve.
NOTE: Saddle type shut-off valves are included in many
water supply kits, but are not recommended for this
application.
NOTE: Commonwealth of Massachusetts Plumbing
Codes 248CMR shall be adhered to. Saddle valves
are illegal and use is not permitted in Massachusetts.
Consult with your licensed plumber.
GE SmartConnect™R
ailable in the following lengths:
av
2' (0.6 m) – WX08X10002
6' (1.8 m) – WX08X10006
15' (4.6 m)
25' (7.6 m) – WX08X10025
Shut off the main water supply.
urn on the near
T
.
ater
of w
• Install a shut-off valve between the icemaker water
valve and cold water pipe in a basement or cabinet.
The shut-off valve should be located where it will be
easily accessible.
efrigerator Tubing Kits are
– WX08X10015
est faucet long enough to clear the line
7
Page 8
Installation Instructions
1/4" Tubing
Tubing Clamp
1/4"
Compression Nut
F
errule
(
sleeve)
SmartConnect™ Tubing
Refrigerator Connection
Step 2A WATER LINE
INSTALLATION WITH
A REVERSE OSMOSIS
SYSTEM
Skip this step when not using RO System
IMPORTANT:
When connecting a GE Reverse Osmosis Water System
to your refrigerator, the GE RVKit must be used. For
other reverse osmosis water systems, follow the
manufacturer’s recommendations.
If the water supply to the refrigerator is from a Reverse
Osmosis Water System, use the refrigerator’s filter
bypass plug. Using the refrigerator’s water filtration
cartridge with the RO filter can result in hollow ice cubes
and slower water flow from the water dispenser.
Turn left to remove Turn right to install bypass plug
STEP 3 CONNECT WATER SUPPLY
Check to be sure that refrigerator power cord is not
plugged into the wall outlet.
If you are using copper tubing:
• Place compression nut and ferrule (sleeve) onto
the end of the tubing coming from the house water
supply.
• Insert the end of the copper tubing into the
refrigerator connection at the back of the
refrigerator, as far as possible. Hold the tubing
in place and tighten the fitting.
If you are using GE SmartConnect™tubing:
• Insert the molded end of the tubing into the
refrigerator connection, at the back of the
refrigerator, and tighten the compression nut
until it is hand tight.
• Then tighten one additional turn with a wrench.
Overtightening may cause leaks.
• Fasten the tubing into the clamp provided to hold it
in position. You may need to pry open the clamp.
• Turn on the water at the shut-off valve to check
for leaks.
STEP 4 CONNECT POWER
• Connect r
ounded r
gr
• Check to make sure power to refrigerator is on by
opening r
e on.
ar
efrigerator pow
eceptacle.
efrigerator door to see if interior lights
er cord plug to a properly
STEP 5 MOVE REFRIGERATOR
INTO POSITION
• Remove outside protective wrapping.
• Move the refrigerator into final installation position.
• Remove door spacer and all inside packaging.
8
Page 9
Rollers
Raise
Roller Adjusting Screw
Doors Should
Align at Top
Raise
Installation Instructions
Roller Adjusting Screws
STEP 6 LEVEL THE REFRIGERATOR
he refrigerator can be leveled by adjusting the rollers
T
located near the bottom hinges.
Rollers have three purposes:
• The rollers adjust so that the door closes easily when
opened about halfway. (Raise the front about 5/8"
[16 mm] from the floor.)
• Rollers adjust to allow the refrigerator to be firmly
positioned on the floor and to prevent rocking
when the doors are opened and closed.
• The rollers allow you to move the refrigerator from the
wall for cleaning.
To Adjust the Rollers:
STEP 7 LEVEL THE DOORS
f the doors are not evenly aligned at the top, the
I
refrigerator door can be adjusted.
Use a 7/16" hex socket or wrench to turn the door
•
adjusting screw. Turn the screw to the right to raise
the door, turn left to lower the door.
• Use a 3/8" hex socket or wrench to turn the
adjustment screws. Turn the screws clockwise to raise
wise to lower it.
efrigerator
the r
• Use a 5/16" hex sock
rear rollers. Turn the screws clockwise to raise the
refrigerator, counter
, turn counter
clockwise to lower it.
clock
et to turn the scr
ews for the
NOTE: A nylon plug is imbedded in the threads of
the pin. The plug is designed to prevent the pin from
turning. A wrench must be used to turn the pin.
• Turn the wrench one or two times. Open and close the
refrigerator door to check alignment with the freezer
door at the top. Adjust again if necessary.
STEP 8 SCREW DOWN SUPPORT LEG
Screw down the support leg until it touches the floor.
This will prevent door misalignment.
9
Page 10
Toekick Screw
Installation Instructions
STEP 9 START ICEMAKER
Power Switch
Feeler Arm
• Slide the switch to ON position. The icemaker
will not begin to operate until it reaches its
operating temperature of 15°F (–9°C) or below.
It will then begin operation automatically. It will
take 2–3 days to fill the ice bin.
• Be sure nothing interferes with the sweep of the feeler
arm. Do not place objects in the path of the feeler arm.
• Discar
• To turn the icemaker off, set the switch to OFF.
d the first full bucket of ice cubes.
STEP 10 TEMPERATURE
CONTROLS
The temperature controls are preset at 37°F for the
•
refrigerator and 0°F for the freezer.
• Allow 24 hours to stabilize before making adjustments.
STEP 11 INSTALL TOEKICK
• Press toekick into position and reinstall one screw on
each side.
IMPORTANT: The vented toekick must remain
unobstructed for proper air circulation.
10
Page 11
Notes
11
Page 12
NOTE: While performing installations described in this book,
GE Consumer & Industrial
Appliances
General Electric Company
Louisville, KY 40225
ge.com
safety glasses or goggles should be w
For Monogram®local service in your area, call
1.800.444.1845.
TE: Product improvement is a continuing endeavor
NO
at General Electric. Ther
specifications ar
Pub. No. 31-46518
Part No. 225D1974P002
02-08 JR
Printed in Mexico
orn.
efore, materials, appearance and
e subject to change without notice.
Loading...