GE Monogram ZDW24 WW, Monogram ZDW24 BB Installation Instructions Manual
GE Monogram
Installation
Instructions
®
Wine Chiller
Model
ZDW24 WW
ZDW24 BB
Before you begin—Read these instructions completely and carefully.
CAUTION
CAUTION
IMPORTANT: Save these instructions for local inspector’s use.
IMPORTANT: OBSERVE ALL GOVERNING CODES AND ORDINANCES.
NOTE TO INSTALLER: Be sure to leave these instructions with the Consumer.
NOTE TO CONSUMER: Keep these instructions with your Use and Care Book for future
reference.
WARNING
This appliance must be properly grounded. See “Electrical Supply”, page 4.
ATTENTION
If you have questions concerning the installation of this product, call the GE Answer
Center® Consumer Information Service at
800.626.2000, 24 hours a day, 7 days a week.
If you received a damaged wine chiller, you
should contact your dealer.
Proper installation is the responsibility of the
installer. Product failure due to improper
installation is not covered under the GE
Appliance Warranty. See the Use & Care
Guide for warranty information.
For Monogram local service in your area,
1-800-444-1845.
For Monogram service in Canada
1-888-880-3030.
For Monogram Parts and Accessories, call
1-800-626-2002.
Cet appareil doit être correctement mis à la terre.
Consulter « Alimentation électrique », page 4.
WARNING
• Use this appliance only for its intended
purpose.
• Immediately repair or replace electric
service cords that have become frayed or
damaged.
• Unplug the wine chiller before cleaning
or making repairs.
• Repairs should be made by a qualified
service technician.
ATTENTION
•Il ne faut utiliser cet appareil que pour
l’usage pour lequel il a été construit.
•Il faut réparer ou remplacer
immédiatement tout cordon
d’alimentation électrique effiloché ou
endommagé.
•Débrancher le réfrigérateur à vin avant le
nettoyage ou toute intervention.
•Les réparations doivent être faites par un
technicien qualifié.
Contents
Design Information
Models Available.................................................................................................................................. 3
Dimensions and Clearances ............................................................................................................... 3
Installation Preparation
Grounding the Wine Chiller .............................................................................................................. 4
Reverse Door Swing ............................................................................................................................ 5
Installation
Step 1: Remove the Packaging ........................................................................................................... 6
Step 2: Install Handle ......................................................................................................................... 6
Step 3: Install Leveling Legs ............................................................................................................... 7
Step 4: Slide the Unit into the Cutout ............................................................................................... 7
2
Design Information
Wine Chiller
Model
Available
Dimensions
& Clearances
ZDW24 WW
White Wine Chiller
ZDW24 BB
Black Wine Chiller
Front ventilation allows the wine chiller
to be installed as a built-in and still operate
efficiently.
The bottom front grille area must remain
unobstructed for proper air circulation and
operation.
Cutout dimensions shown allow for a full door
swing and access to the pull-out racks.
The Monogram wine chiller adds an eloquent
statement of style, convenience and flexibility.
The Monogram wine chiller can be used
freestanding or as a built-in.
34-1/2"-35"
Locate
Outlet
5"
24" Min.
24-1/8"
24" Min.
34-1/2"
23-7/8"
Installation
Options
Increase storage capacity by installing two
Monogram wine chillers side by side. Or,
install the wine chiller next to a Monogram
beverage center for a complete refreshment
center.
A side by side installation requires a 48" wide
opening. No trim kits required.
•The glass door fronts should align evenly
with adjacent cabinet door fronts.
Frameless Cabinets:
• If installing between frameless cabinets, a
1/2" wide filler strip or side panel may be
required. The filler strip will act as a spacer
between the door case and adjacent cabinet
and will prevent interference with cabinet
door swing. The width of the opening must
include filler panels.
Provide two separate properly grounded
electrical outlets for a side by side installation.
Each electrical outlet should have a voltage
rating that matches the rating plate.
3
Loading...