GE Monogram ZDIS15 Design And Installation Manual

Installation
Instructions

Automatic Icemaker

ZDI15
ZDIS15

Design Guide with
Installation Instructions

Monogram:_

Installation Instructions

BEFORE YOU BEGIN

Read these instructions completely and
carefully.

• IMPORTANT- Save these instructions for

local inspector's use.

• IMPORTANT- Observe all governing codes

and ordinances.

• Note to Installer - Be sure to leave these
instructions with the Consumer.

• Note to Consumer - Keep these instructions

with your Owner's Manual for future reference.

WARNING:

This appliance must be properly grounded.
See "Power Supply", page 4.

AVERTISSEMENT :

Get appareil doit _tre correctement mis

la terre. Consulter _{Alimentation

_lectrique _, page 4.

If you received a damaged ice machine, you should

immediately contact your dealer or builder.

Proper installation is the responsibility of the installer.
Product failure due to improper installation is not

covered under the GEAppliance Warranty. See the
Owner's Manual for warranty information.

• Use this appliance only for its intended purpose.

Check with local utilities for electrical codes that apply
in your area. Local codes vary. Installation, electrical

connections and grounding must comply with
applicable codes. In the absence of local codes, the
ice machine should be installed in accordance with

National Electrical Code ANSl/NFPA 70-1990 or latest
edition.

For Monogram local service inyour area, call

1.800.444.1845.

For Monogram Service in Canada, call

1.888.880.3030.

For Monogram Parts and Accessories, call

1.800.626.2002.

CONTENTS

Design Information

Models Available ..............................................................3

Cutout & Product Dimensions ........................................3

Optional Accessories ......................................................3

Tools and Materials Required ......................................3

Installation

Advance Planning ............................................................4

Power Supply ....................................................................4

Remove Packaging ..........................................................5

Adjust Height of Ice Machine ........................................5

Water Supply ....................................................................6

Connect the Drain ............................................................6

Connect Water Supply ....................................................7

Reverse Door Swing ....................................................7, 8

Accessories

ZIP75WW, ZIP75BB Kit for 3/4" thick panels ........9, 10

Design Information

MODELS AVAILABLE

ZDI15, ZDIS15
Available in black, white and stainless steel.

The ice machine may be installed below a countertop
or used free-standing.

CUTOUT & PRODUCT DIMENSIONS

34" min.

Adjustable

to 34-1/2"

Cutout dimensions shown allow for a full door swing.

When installing a 3/4"thick custom door panel,

additional clearances atthe sides may be required.
Frameless Cabinets:

• If installing between frameless cabinets, a 1/2" filler
strip or side panel may be required on the hinge side.
The filler strip will act as a spacer between the door

case and adjacent cabinet, and will prevent
interference with icemaker door swing. The width of

the opening must include filler or side panel thickness.

NOTE: The addition of a 3/4" thick front panel will result
in a front to back depth of 24-1/16."

23-5/16" to

14-13/16'

OPTIONAL ACCESSORIES

ZIP75WW White and ZIP75BB Black--For the
installation of atrimless 3/4" thick custom panel on

white and black models (not for stainless steel models).
A custom handle of your choice may be installed
onto the 3/4" panel. See installation instructions on
pages 9 and 10.

ZPK1--Drain Pump Kit. For use when a floor drain is
not available.

TOOLS AND MATERIALS REQUIRED

• 1/4" socket

• 3/4" adjustable wrench

•Level

• GE SmartConnectTM Refrigerator Tubing Kit or 1/4" O.D.
copper tubing, of sufficient length to reach the installation

3

Installation Instructions

ADVANCE PLANNING

CAUTION: Duetoexcessive

weight, TWO PEOPLEARE REQUIREDTO
MOVE AND INSTALL THIS ICE MACHINE.

MISE EN GARDE :

A cause de son poids elev&lL FAUT
DEUX PERSONNES POUR DEPLACER ET

INSTALLERCEDISTRIBUTEUR DE GLACE.

Choose the location:

• The ice machine must be installed in an area
protected from elements such as wind, rain, water

spray or drip. The area should be ventilated with
temperatures above 55°F (13°C) and below 110°F
(43°C). Best results are obtained between 70°F (21°C)
and 90°F (32°C).

• The ice machine may be closed in on the top and
three sides as long as the front is unobstructed for
air circulation and proper operation.

-Installation should be such thatthe ice machine
can be moved forward for servicing, if necessary.

-The bottom grille on the front must be unobstructed

to provide proper air flow.

Before you begin:

1. If a custom panel is to be installed, follow the

instructions shown on pages 9 and 10.

-Order ZIP75 (black or white) panel kit.

-Order the custom panel from the cabinet
manufacturer.

-Secure the custom panel onto the ice machine.

2. Determine a method of drainage. If a floor drain is
to be installed, the drain must be accurately

located. The installation of a custom door panel will

affect the drain location. See page 6 to determine
the exact location of the floor drain, front to back,
with or without a custom door panel.

-A drain pump kit, ZPK1, is available and will not

interfere with placement of the ice machine.

3. The door swing is reversible. If desired, change the
door swing before installation.

4. Slide the ice machine into the installation location.

-Open and close the door to be sure there is no
interference.

-Check to be sure the ice machine can be
moved back into the opening, flush with adjacent

cabinetry. There should be no interference with

the floor drain.

POWER SUPPLY

IMPORTANT: (Please read carefully).

FORPERSONAL SAFETY,THIS APPLIANCE MUST BE

PROPERLYGROUNDED.

Do not use an extension cord or adapter plug with
this appliance. Follow National Electrical Code or
prevailing local codes and ordinances.

This ice machine must be supplied with 115V,60Hz,
and connected to an individual, properly grounded
branch circuit, and protected by a 15 or 20 amp circuit
breaker or time delay fuse.

Electrical Supply Should
Enter From Back Wall

InShaded Area.

• A properly grounded 3-prong receptacle should be
located within reach of the ice machine's 66" long
power cord. For a built-in installation, locate the
receptacle in the shaded area shown.

IMPORTANT: (Please read carefully).

The power cord of this appliance is
equipped with a three-prong
(grounding) plug that mates with
a standard three-prong grounding
wall receptacle to minimize the
possibility of electric shock. The
customer should have the wall receptacle and circuit
checked by a qualified electrician to make sure the
receptacle is properly grounded and has the correct
polarity.

• Where a standard two-prong wall receptacle is
encountered, it is the personal responsibility and
obligation of the customer to have it replaced with
a properly grounded three-prong wall receptacle.

Do not,under any circumstances, cut or remove
the third (ground) prong from the power cord.

DO NOT USEAN EXTENSION CORD.

4