GE Monogram ZDIC150, Monogram ZDIS150 Installation Instructions Manual

Installation

I struct" n

Automatic Icemaker

ZDIC150
ZDIS1S0

Design Guide

With Instollotion Instructions

monogram.com

Installation Instructions

• BEFORE YOU BEGIN:

Read these instructions completely and carefully.

• IMPORTANT:

Save these instructions for local inspector's use.

• IMPORTANT:

Observe all governing codes and ordinances.

, Note to Installer- Be sure to leave these

instructions with the Consumer.

, Note to Consumer - Keep these instructions

with your Owner's Manual for future reference.

-&WARNING:

This appliance must be properly grounded.

Failure to do so can result in death, fire or electrical

shock. See "Power Supply;' page 6.

A AVERTISSEMENT :

Cet appareil doit _tre correctement
mis 5 la terra. Le non-respect de ces instructions
peut causer la mort, un incendie ou un choc
61ectrique. Consulter <<Alimentation 61ectrique >>,

page 6.

CONTENTS

Design Information

Models Available ....................................................................:3

Cutout & Product Dimensions ..........................................3

Optional Accessories ............................................................4

Tools and Materials Required ........................................4

Installation

Advance Planning ..................................................................5

Power Supply ..........................................................................6

Remove Packaging ................................................................6

Adjust Height of Icemaker ................................................6

Water Supply ..........................................................................7

Connect the Drain ..................................................................7

Connect Water Supply ........................................................8

Reverse Door Swing ........................................................8, 9

Accessories

ZIP75BB Kit for 3/4" thick panels ..........................10, 11

If you received a damaged icemaker, you should

immediately contact your dealer or builder.

Proper installation is the responsibility of the
installer. Product failure due to improper installation
is not covered under the GE Appliance Warranty.
See the Owner's Manual for warranty information.

• Use this appliance only for its intended purpose.

Check with local utilities for electrical codes that
apply in your area. Local codes vary. Installation,

electrical connections and grounding must comply
with applicable codes. In the absence of local codes,

the icemaker should be installed in accordance with

National Electrical Code ANSI/NFPA 70-1990 or
latest edition.

For Monogram local service in your area, call

1.800.444.1845.

For Monogram Service in Canada, call

1.800.561.3344.

For Monogram Parts and Accessories, call

1.800.626.2002.

Design Information

MODELS AVAILABLE

ZDIC150, ZDIS150 The icemaker may be installed below a countertop
Available in black and stainless steel, or used free-standing.

CUTOUT & PRODUCT DIMENSIONS

Flush Installation, Top View

34" to

34-1/2"

custompanelwill requirean
additional1-1/2"wide filler

./The installationof a3/4"thick

striponthehingeside.

15 X,

"15-1/2"

*'16-1/2"

34" rain.

Adjustable

to 34-1/2"

23-5/16"to
DoorFront \

*For flush installation of ZDIS150 and ZDIC150 models: Install

a !/2"-wide filler strip on the hinge side. The filler strip will act as
a spacer between the door case and adjacent cabinets and will

prevent interference with the cabinet door swing. Recessthe
filler strip !" back from the front face of the icemaker, or even
with the front edge of the product case. The width of the
opening must be !5-!/2" (including the !/2" filler strip).

**The black model ZDIC150 with a custom panel cannot

be installed flush. A !-!/2"-wide filler strip is required on the

hinge side. The icemaker will project forward 3//4"of adjacent

cabinets. Recess the filler strip 1-3/4" back from the front face

of the icemaker or even with the front edge of the product case.
The width of the opening must be !6-!/2" wide, including the

!-!/2" filler strip.

1/2"-widefiller

panel or cleat set

backevenwith
frontofcase.\

CABINET

Custom Panel Installation Top View

1-1/2"-widefiller
panelorcleatset

backevenwith
frontofcase.

CABINET

3/4" --

A

Cutout dimensions shown allow for a full door swing.

Corner Installation

I

Factory set t

for110° door ',,

swing.Allow2"",,
min.towallfor '",

90° doorswing

\\ i

o ; i

110 ', ',u

5-1/2" Minimum

toWall

Installation Instructions

OPTIONAL ACCESSORIES

ZIP75BB Black--For the installation of a trimless
3/4" thick custom panel on black models (not for

stainless steel models). This kit provides a handle
that can be installed with the custom panel.
A custom handle of gout choice mag be installed
onto the 13/4"panel. See installation instructions
on pages 10 and 11.

TOOLS AND MATERIALS REQUIRED

• 1/4" socket

• 3/4" adjustable wrench
Level

GESmartConnect TM Refrigerator Tubing Kit or 1/4" O.D.
copper tubing, of sufficient length to reach the installation

ZPK1--Drain Pump Kit. For use when a floor drain is
not available. The drain pump must be installed inside
the unit and can operate at a maximum vertical
height of 10 feet. 10 feet of tubing is supplied with

the kit.

4