GE Monogram ZBD5700DBB Dimension Manual

Monogram.

™

ZBD5700DBB—GE Monogram Dishwasher with Stainless Steel Interior

For answers to your Monogram,

®

GE Profile Performance Series,

™

GE Profile™or GE appliance questions, call
GE Answer Center®service, 800.626.2000.

R

Listed by
Underwriters
Laboratories

Revised 12/98

Dimensions and Specifications (in inches)

Design Information: This dishwasher is supplied as

a Black model.
A toekick is supplied and may be covered with a

custom toekick to match kitchen decor.
Side trim is not required. Side filler strips are supplied

to fill a 24" wide opening.

Additional Specifications: A 120 Volt, 60 Hz power
supply is required. An individual properly grounded
branch circuit protected by a 15 or 20 amp circuit
breaker or time delay fuse is recommended. Install a
3-prong electrical receptacle at least 6" above the
floor and within 18" of the right or left adjacent
cabinet wall. Wiring must enter the cutout in shaded
area shown. A double, side-by-side installation
requires two separate circuits.

The hot water line must enter the cutout in the shaded
area from the right, left, rear or through the floor. The
water line should be 3/8" O.D. copper or 1/2" O.D.
plastic. Installation of an easily accessible hand
shut-off valve is strongly recommended.

The dishwasher should be placed no more than 10 feet
from the sink for proper drainage.

If the dishwasher is to be located in or near a corner
of base cabinets, allow 2" min. clearance from the
corner to prevent interference with adjacent door
handles.

Optional Trim Kits:

• ZPF25W, white or ZPF25B, black custom panel
kit–Provides for the installation of a 1/4”
thick custom door panel.

• ZPF75W, white or ZPF75B, black custom panel
kit–Provides for a trimless appearance using a 3/4”
thick custom door panel.

23-5/8"

5"

34" Min.
35" Max.

2-7/8" Min.

4" Max.

Toekick

25 1/4"

From

Cabinet Face

23 1/2"

3 1/4"

24"

1-3/4"

Min.

6"

Plumbing and Electric Service

Must Enter Inside This Area

34" Min.

35" Max.

Underside of

Countertop

to Floor

23-5/8" Min.

24" Max.

This Wall Area

Must be Free of

Pipes or Wires

Monogram.

™

ZBD5700DBB—GE Monogram Dishwasher with Stainless Steel Interior

•Cut door panel to the dimensions shown.

•The bottom left and right corners should be
cut at 1/4” radius. See illustration.

NOTE: The trim will conceal the cut edges of
the panel.

1/4" Thick

Door Panel

25-1/2"

23-1/8"

1/4"

Radius

Cut

Custom Door and Access Panel Dimensions

For answers to your Monogram,

®

GE Profile Performance Series,

™

GE Profile™or GE appliance questions, call
GE Answer Center®service, 800.626.2000.

R

Listed by
Underwriters
Laboratories

Revised 12/98

Dim. A*

*Height

23-1/8"

Custom

Panel Size

Floor

Cabinets

Countertop

Top

3/4" Max.

3/4" Thick

Door Panel

Bottom of
Adjacent Cabinetry

*Height is equal to A minus 5-1/8" plus 1/4"
EXAMPLE:
*Height = 30-1/2" minus 5-1/8" plus 1/4" is equal to 25-5

The custom panel should be constructed in
the same manner as cabinet doors. All edges
can be seen and must be finished for the
best appearance.

• Measure dimension A, from underside of

countertop to bottom of adjacent cabinets.
–Subtract 5-1/8”. Control panel height is 5”.

Allow 1/8” for gap between bottom of
countertop and top of control panel.

–Add 1/4”. The custom panel will slide up,

behind control panel.