Page 1
JVB98SH – GE Profile™36" Telescopic Downdraft System
Specification Created 7/03
220961
TM
2-1/4
6-3/8
3-1/4
33-7/8
36
17-1/8
20-5/8
12-1/8
7-1/4
7-1/2
8-1/2
27
C
L
Overall Dimensions (in inches) Venting Options (in inches)
Installation Information: Before installing, consult installation instructions
packed with product for current dimensional data.
For answers to your Monogram,
®
GE Profile™or
GE®appliance questions, visit our website at
GEAppliances.com or call
GE Answer Center®service, 800.626.2000.
Through the Floor
In Cabinet Discharge (Down)
In Cabinet Discharge (Right)
In Cabinet Discharge (Left)
R
Listed by
Underwriters
Laboratories
Note: Telescopic downdraft vents are not recommended to be
installed with cooktops that are flush mounted.
Approved for use with the following GE Profile
™
and GE cooktops –
36" and 30" electric models, 36" and 30” gas sealed burner models
and 36" and 30" induction models.
Not approved for use with standard burner gas cooktops.
Note:
The countertop must be at least 26" deep with a flat surface
area of 23-1/2" or more, front to back. In addition, other clearances
to the front edge of the countertop must be considered.
Note: Dimensions shown are for reference only. Before cutting out
countertop, refer to instructions packed with
downdraft and cooktop.
Note: Installation in cabinets/countertops against the wall
will not be possible in most applications. Against the wall
installations are limited to dimension requirements. Refer to
installation instructions packed with product for further details.
JXBC67 Outdoor Cover.
Optional accessory may be ordered for
installation of motor and blower assembly on outside wall.
JXRB67 Indoor Remote Accessory. Optional accessory may be
ordered for installation of motor and blower assembly in an indoor
remote location.
Installation Information: Before installing, consult installation
instructions packed with product for current dimensional data.
Page 2
JVB98SH – GE Profile™36" Telescopic Downdraft System
TM
6" Round
Straight
3-1/4" x 10"
Straight
6"
90° Elbow
6"
45° Elbow
3-1/4" x 10"
90° Elbow
3-1/4" x 10"
45° Elbow
3-1/4" x 10"
45° Elbow
6" Round
to 3-1/4 x 10"
Transitions
3-1/4" x 10"
to 6" Round
Transition
6" Round
to 3-1/4 x 10"
Transitions
90° Elbow
3-1/4" x 10"
to 6" Round
Transition
90° Elbow
6" Round
Wall Cap
with Damper
3-1/4" x 10"
Wall Cap
with Damper
p
6" Round
Roof Cap
6" Round
Roof Vent
Duct Pieces
Equivalent Length*
Duct Pieces
Equivalent Length*
1 ft. (per foot length)
1 ft. (per foot length)
15 ft.
9 ft.
16 ft.
5 ft.
24 ft.
7 ft.
5 ft.
20 ft.
12 ft.
21 ft.
27 ft.
20 ft.
24 ft.
SHOULD NOT EXCEED 100 EQUIVALENT FT.
*Equivalent length of duct pieces are based on actual test conducted by
GE Evaluation Engineering and reflect requirements for good venting
performance with a downdraft rated at 500 CFM
Venting Duct Information
Plan the Ductwork
1. This downdraft blower system is designed for use with 3-1/4" x 10"
ductwork (can be transitioned to 6" round). Two different discharge
directions are available with side-to-side adjustment for the accurate
alignment of ductwork.
2. For best performance: choose the ducting option which allows the shortest
length of ductwork and a minimum number of elbows and transitions.
Check location of floor joists, wall joists, wall studs, electrical wiring or
plumbing for possible interference.
Steps to Determine Flexible Ducting’s Equivalent Length
1. Measure the actual amount of offset (Maximum 3" recommended).
The effect upon airflow is dependent upon the amount of offset.
2. Calculate the equivalent ducting allowances using:
(__in. offset) x (14 Ft. per inch)
=__Ft. equivalent length.
1. Ensure that the total equivalent length of ducting does not exceed the
maximum recommendation of 150 feet.
Left discharge
(as shipped)
Right
discharge
Specification Created 7/03
220961
For answers to your Monogram,® GE Profile™or
GE®appliance questions, visit our website at
GEAppliances.com or call
GE Answer Center®service, 800.626.2000.
R
Listed by
Underwriters
Laboratories
Page 3
Specification Created 7/03
220961
TM
JVB98SH – GE Profile™36" Telescopic Downdraft System
L
O
4
OFF
L
O
4
O
FF
L
EF
T
RIGHT
Features and Benefits
•Telescopic downdraft hood – Hood raises over cooktop surface and retracts when not in use.
• 500 CFM – Powerful 500 CFM performance removes smoke and vapors from the cooking area.
• Variable speed fan control – The powerful variable speed exhaust system effectively pulls
smoke and vapors out of the kitchen.
• Removable grease filter – Durable filters can be removed for easy cleaning and maintenance.
• Model JVB98SHSS – Stainless steel
Loading...