GE JKP30BM1BB, JKP30CM1CC, JKP30SM1SS, JKP30WM1WW, JKP35BM1BB Installation Guide

Installati

Built-ln Wall Oven

27" (68.6 cm) models
JKSI0, JKP30, JKP35, JKP55, JKP70, JKP75,

PK916, PK956, ZEK938, ZEK958

instructions

30" (76.2 cm) models

JTP30, JTP35, JTP55, JTP70, JTP75, PT916,
PT920, PT956, PT960, ZET938, ZET958

if you have questions, call 1.800.GE.CARES or visit our website at:
ge.com

Before You Begi n • Proper installationistheresponsibility

Read these instructions carefully and completely.

• IMPORTANT-save these

instructions for local inspector's use.

of the installer and product failure due
to improper installation is NOT covered
under warranty.

NOTE=This appliance must be properly
grounded.

• IMPORTANT-obse_,e all

governing codes and ordinances.

• Note to InstallermBe sure to leave these
instructions with the consumer.

• Note to ConsumermKeep these
instructions for future reference.

ATTENTION INSTALLER

All electric wall ovens must be hard wired
(direct wired) into an approved junction

box. A plug and receptacle is NOT permitted

on these products.

Parts Included

(Appearance will vary)

Screws For Installation
(8-18 x .750 flat head

Phillips wood screws)

(68.6 cm)
Metal Bottom

Trim Assembly
(on some models or
can be purchased

separately)

27" (68.6 cm)

Metal Bottom Trim

30" (76.2 cm)
Metal Bottom Trim

Assembly

Materials Needed

__ _ WireNu_ts

Strain Relief Clamp Junction
for 1/2" conduit Box _k_ _

36" (91 cm)
of String

Tools Needed

1/8" (3 mm) Drill Bit and
Electric or Hand Drill

Phillips
Screwdriver

31-10647-2 07-07 JR

Installation Instructions

IMPORTANT SAFETY INSTRUCTIONS

For Your Safety

• Be sure your oven is installed properly by

a qualified installer or service technician.

• Be sure the oven is securely installed in a
cabinet that is firmly attached to the house
structure. Weight on the oven door could
cause the oven to tip and result in injury.

Never allow anyone to climb, sit, stand or
hang on the oven door.

• Make sure the cabinets and wall
coverings around the oven can withstand

the temperatures (up to 200°F [93.3°C])
generated by the oven.

WARNING: The electrical

power to the oven supply line
must be shut off while line

connections are being made. Failure

to do so could result in serious injury

or death.

Electrical
Requirements

This appliance must be supplied with the proper
voltage and frequency, and connected to an

individual, properly grounded branch circuit,
protected by a circuit breaker or fuse. See the

rating plate located on the oven frame to determine
the rating of the product. Use the chart below to

determine the minimum recommended dedicated
circuit protection.

Recommended

KW Rating KW Rating Circuit Size

240V 208V (Dedicated)

<4.8 KW <4.1 KW 20 Amp

4.9 KW-7.2 KW 4.3 KW-6.2 KW 30 Amp

7.3 KW-9.6 KW 6.3 KW-8.3 KW 40 Amp

9.7 KW-12.0 KW 8.4 KW-10.4 KW 50 Amp

Electrical
Requirements cont.

Rating plate is located on oven side trim,
side front frame or lower front frame.

Rating Plate

Location _ ¢--h

I -- I

We recommend you have the electrical wiring
and hookup of your oven connected by a qualified
electrician. After installation, have the electrician

show you where your main oven disconnect is
located.

Check with your local utilities for electrical codes
which apply in your area. Failure to wire your oven

according to governing codes could result in a
hazardous condition. If there are no local codes,

your oven must be wired and fused to meet the
requirements of the National Electrical Code,

ANSI/NFPA No. 70-Latest Edition. You can
get a copy by writing:

National Fire Protection Association
Batterymarch Park

Quincy, MA 02269

Effective January 1, 1996, the National
Electrical Code requires that new, but not existing,

construction utilize a four-conductor connection to
an electric oven. When installing an electric oven

in new construction, a mobile home, recreational
vehicle or an area where local codes prohibit
grounding through the neutral conductor,

follow the instructions in the section on NEW
CONSTRUCTION AND FOUR-CONDUCTOR

BRANCH CIRCUIT CONNECTION.
You must use a three-wire, single-phase A.C.

208Y/120 Volt or 240/120 Volt, 60 hertz electrical
system. If you connect to aluminum wiring,

properly installed connectors approved for
use with aluminum wiring must be used.

2

Installation Instructions

Pre-lnstallation Checklist

ALL INSTALLATION INFORMATION

ON THE FOLLOWING PAGES IS TO
BE USED FOR SINGLEAND DOUBLE
OVEN INSTALLATION!

i

Door removal is not a requirement for
installation of the product, but is an

added convenience. To remove the door:

Open the oven door as far as it will go.

Remove packaging materials.

Check behind hinges and under
false bottom. Remove labels on the

outside of the door, plastic on trims
and panel, all tape around the oven,
and any shipping screws securing
the oven to the base pad.

Oven Racks

_ iterature

Open oven door and remove literature
pack and oven racks.

Remove Installation Instructions from
literature pack and read them carefully

before you begin.

Be sure to place all literature, Owner's
Manual, Installations, etc. in a safe place

for future reference.

Pack

Push both hinge Hinge

locks down toward ._I_'.!_L. Position
the door frame, Hinge"':':_
to the unlocked s_ot _.d

position. This may

require a flat blade
screwdriver. Arm

DO NOT LIFT THE DOOR

BY THE HANDLE!

Place hands on both sides of "Ff_
the door, and close the oven I1_

door to the removal position, I_/
which is most of the way closed. I_//

[_ ift door up and

NOTE: The oven door is very heavy. Be sure

you have a firm grip before lifting the oven

door off the hinges. Use caution once the
door is removed. Do not lay the door on its

handle. This could cause dents or scratches.

out until the

hinge arms
clear the slots.

Place the oven on a table or platform

even with the cutout opening. (Platform

must support 150 Ibs. [68 Kg] single,

275 Ibs. [124 Kg] double.)

_._L. Unlocked

Hinge

Hinge Clears Slot

Remove the bottom trim from the top

of the oven. It will be installed at the end

of the installation process. The trim is

wrapped separately and taped to

the top of the unit.

3

Installation instructions

Cutou for 27"(68.6

Ovens only

For JKS10, JKP30, JKP70, PK916, ZEK938 models only.

Cabinet_ !_L Junction Box

27" (68.6 cm) i

Cutout Width T
25" (83.5 cm)

Allow 1" (2.5 cm)
for overlap of

oven over side

edges of cutout

2" x 4"

{5crux tOcm)

OF
Funnors ievei

with bottom

of cutout

20" (50.8 cm)

... --. --_ . °7-' Allow

Allow a minimum
of 20" (50,8 crn) for

clearance to adjacent overlap of

corners, drawers, wails, oven top and
etc. when door is open of cutout'_'_'_

Min. , : ,

25 1/4" (64.1 "!-'

Max.

1" (2.5 cm)

minimum for

bottom

5" (12.7 cm)

Max. from the

left or right

i

Location

Cutout

Height 22" (55.9 cm)
27 5/8" Min. above

(70.2 cm) Min. base rail

28 1/8" I

Box Location -

access from

AIternate Junction
adjacent cabinet

Recommended may be required

cutout location

from floor 32 1/2"

(82.6 cm)

ngle

Cabinet Width

27" (68.6 cm)

uilt-ln

Recommended
Cutout Location
from Floor

Cutout Depth

32 1/2" (82.6 cm)
23 112"

(59.7 cm) Min.

Cutout Width

25" (63.5 cm) Min.
25 1/4" (64.1 cm) Max.

Cutout Height

27 5/8" (70.2 cm) Min.
28 1/8" (71.4 cm) Max.

NOTE: if the cabinet does not
have a front frame and the sides

are less than 3/4" (1.9 cm) thick,

shim both sides equally to

establish the cutout width.

if the cabinet does not have a solid bottom,
two braces or runners must be installed

level with the bottom of the cutout to
support the weight of the oven. For

single ovens, the runners and braces
must support 150 Ibs (68 Kg).

NOTE: If marks, blemishes or the

cutout opening are visible above the
installed oven, it may be necessary to

add wood shims under the runners and
front trim until the marks or opening

are covered.

2" x 4" (5 crn x 10 crn) or

equivaJent runners |eve|

with bottom of cutou_

f

T

24"

(Sl cm)

1

I_ 18- (45.7 cm) --_1

27" (68.6 cm)

These ovens are not approved for
stackabie installations.

4

Cutoutfor 27"(68.6 DoubleBuilt-in
Ovensonly

For JKP35, JKP55, JKP75, PK956, ZEK958 models only.

Allow 1" (2.5 cm)
for overlap of

oven over side
edges of cutout

Allow a minimum
of 20" (50.8 cm)

for cmearance to
adjacent corners,

drawers, wails, etc.
when door is open

Installation instructions

6"

(12.7 cm)

Max. from

the left or

Cabinet right

(68.6 cm)

Cutout

Width _-

S" (63.5 cm) Min.

-- 25 !/4" i

i Junction Box

(64.icm)M_TlX,

iCut°ut Above

iHeight base rail
i49 11/16"

i(126.2 cm) Min.
150118"
i(127.3 cm) Max.

...-

s o

B#

Allow i

(2.5 cm) for
overlap of oven from floor i3 114"

and

top

of cutout

bottom _] (33.7 cm)

Recommended

cutout location

Location

(111.8 cm)

Min,

Cabinet Width 27" (68.6 cm)

Recommended
Cutout Location

from Floor i3 i/4" (33.7 cm)

Cutout Depth 23 5/8" (60 cm) Min.
Cutout Width

25" (63.5 cm) Min.
25 i/4" (64.i cm) Max.

Cutout Height 49 Jill6" (i26.2 cm) Min.

50 i!8" (i27.3 cm) Max.

NOTE: if the cabinet does
not have a front frame and
the sides are less than 3/4"

(1.9 cm) thick, shim both
sides equally to establish

the cutout width.

If the cabinet does not have a solid bottom,

two braces or runners must be installed to
support the weight of the oven. For double

ovens, the runners and braces must

support 300 Ibs (135 Kg).

NOTE: If marks, blemishes or the

cutout opening are visible above the
installed oven, it may be necessary to

add wood shims under the runners and
front trim until the marks or opening

are covered.

Suitable
Bracing

to Support

5

18"

(46.7 cm)

Over Centerline

of Cabinet

2" X 4"

(ScmxtOcm)
or equivalent

runners level
with bottom
of cutout

Installation Instructions

IAICutout for 27" (68.6cm)Single Built-In

Ovens only Under Counter

For JKS10, JKP30, JKP70, PK916, ZEK938 models only.

Gas or electric cooktops may
be installed over this oven.

See cooktop installation
instructions for cutout size,

See label on top of oven for
approved cooktop models.

25" (63.5 cm)

,\

\

\

\

240V / 208V
Junction Box 5"

Location (12.7 cm)

Max. from the

left or right

side

Gas and electrical connections

for gas cooktop must be located

in an adjacent accessible
location to the right.

Top and/or side fillers

may be necessary
if unit is positioned
between existing

cabinets. Be sure

they are attached

securely, since they

will anchor the oven

in the cabinet.

_25" (63.5 cm) Min.

25 1/4" (64.1cm) Max.

27 5/8" (70,2 cm) Min.
28 1/8" (71.4 cm) Max. "_; ""

Allow "--4.

1 "

(2.S cm)
unit overlap top

bottom of

oven, 1" (2.5 cm)
unit overlap side

edges

22" (55.9 cm) Min.
Above Support

Platform

24" (61cm)

36" (91.4 cm)

Typical

Countertop
Height

6

Cabinetry

Cutout for 27" (68.6c_)Single or
Double uilt-ln Ovens only-Over a

arming Drawer

For JKSI0, JKP30, JKP35, JKP55, JKP70, JKP75, PK916, PK956, ZEK938,
ZEK958 models only.

Single 27" (68.6 cm)

Oven Over

a Warming Drawer

Anti-Tip B!ock Against

Rear Wall Per Warming
Drawer Requirement

2" (S.1 cm)
Min.

Per

Warming

Drawer
Requirement

NOTE: Additional clearances between cutouts
may be required. Check to be sure the oven

supports above the Warming Drawer location
do not obstruct the required interior depth and
height.

J

1" (2.5 cm) Min. Above Toekick or

Adjust to Oven Installation Height

NOTE: Install the
oven only with

specific models
listed on the label

located on top of
the oven.

• When installing a Warming Drawer below

Double 27" (68.6 cm)

Oven Over

a Warming Drawer

Anti-Tip Block
Against Rear

•Wall Per
Warming

Drawer
Requirement

2" (5.1 cm)

Min.

Per Warming
Drawer

Reql

1" (2.5 cm) Min. Above Toekick

a single or double oven, a separate 120V,
60 Hz, properly grounded receptacle must

be installed. Refer to installation instructions
packed with the Warming Drawer for

specific installation requirements.

7

Cabinetry

Cutoutfor 27"(68.6_)Single Ovensonly-
BelowanAdvantiumor ;rowaveOven

orBetweenanAdvantiumor crowave
Ovenanda rmingDrawer

For JKSI0, JKP30, JKP70, PK916, ZEK938 models only.

Single 27" (68.6 cm) Oven

Below an Advantium or
Microwave Oven

Per Advantium or

Microwave Oven

Requirement

Note: Install the
oven only with

specific models
listed on the label

located on top of
the oven.

NOTE: The middle rail separating the two
openings may need to be larger than the 3"

(7.6 cm) minimum shown. Always refer to the
individual installation instructions packed with
each product for specific requirements.

Combined Advantium or Microwave
Oven and Wall Oven Installation:

When installed in combination with a
single wall oven, use separate electrical

junction boxes.

Refer to the Advantium or microwave
oven installation instructions for electrical

requirements of that product.
These connections must be made

by a qualified electrician. All electrical
connections must meet National Electrical

Code or prevailing local codes.

Single 27" (68.6 cm) Oven

Between an Advantium or
Microwave Oven and a

Warming Drawer

Per Advanfium or
Microwave Oven

Requirement

2" (5.1 cm) Min.

Per Warming
Drawer

Req

NOTE: Additional clearances may be
required. Check to be sure the oven

supports above the Warming Drawer

do not obstruct the required interior depth

and height. The middle rail separating the

openings may need to be larger than the 2"

(5.1 cm) minimum shown. Always refer to
the individual installation instructions packed
with each product for specific requirements.

Warming Drawer Combined with

Advantium or Microwave Oven and

Single Oven:

Install a separate 120V, 60Hz, properly
grounded receptacle. See installation

instructions packed with each product
for specific requirements.

8

Cutoutfor 30"(76.2 cm)Single Built-In
Ovens only

For JTP30, JTP70, PT916, PT920, ZET938 models only.

Allow 11/16"

(1.75 cm) for
overlap of oven

over side edges
of cutout

Installation Instructions

Cutout 7 3/4" (19.7 cm)

Width Max. Junction Box

28 1/2" (72.4 cm), -f- Location

28 5/8" (72.7 cm). may be

"====_: Max. located in

adjacent

-<- Min. __ (junction box

Inside Walls I ['44Height i = ' 22" (65.9 cm)

MustBe II! 271/4" iin. to

At Least Min.
28 1/2" I t_ 27 6/16" Junction Box

(72.4 cm) cm) Max.

I [_ (69.2 cm) Bottom of

(69.4

/ cabinet)

Cabinet Width

Recommended

Cutout Location
from Floor

Cutout Depth
Cutout Width

Cutout Height

30" (76.2 cm)

32 1/2" (82.6 cm)
23 1/2" (59.7 cm) Min.
28 1/2" (72.4 cm) Min.
28 5/8" (72.7 cm) Max.
27 1/4" (69.2 cm) Min.
27 5/16" (69.4 cm) Max.

21" (53.3 cm) - _ "

S

Allow a minimum

of 21" (53.3 cm) for
clearance to adjacent
corners, drawers,
walls, etc. when
door is open

Wide* - ] "_

Recommended

Allow 1" (2.5 cm)

minimum for

overlap of oven

top and 1W"

(3.2 cm) overlap

of oven bottom

of cutout_-_,

Cabinet

Width

30" (76.2 cm)

cutout location
from floor 32 1/2"

If the cabinet does not have a solid bottom,
two braces or runners must be installed

level with the bottom of the cutout to
support the weight of the oven. For single

ovens, the runners and braces must
support 150 Ibs (68 Kg).

NOTE: If marks, blemishes or the
cutout opening are visible above the
installed oven, it may be necessary to

add wood shims under the runners and
front trim until the marks or opening

are covered.

NOTE: If the cabinet does
not have a front frame and the

sides are less than 3/4" (1.9 cm)
thick, shim both sides equally to

establish the cutout width.

m J

-- 2" x 4"

Suitable
Bracing

to Support

Runners --

-F--_(s4 216/6"

.9cm) Over \

Centerline
of Cabinet

Side by Side Installations

Install two wall ovens in separate cutouts.

Allow 2" (5.1 cm) min. between cutouts.

(5 cm x 10 cm
or equivalent

runners level
with bottom
of cutout

These ovens are not approved for
stackable installations.

Cutout - 2" (5.1 cm)

Observe all Min.
dimensions I"_===='m='=_

and

requ rements.

9

Cutout -

Observe all

dimensions

and

requirements.

Installation Instructions

IAICutoutfor30' 6.2cm)Double Built-InOvensonly

For JTP35, JTP55, JTP75, PT956, PT960, ZET958 models only.

Allow 11/16"
(1.76 cm) for
overlap of oven
over side edges

of cutout

Allow a minimum
of 21" (53.3 cm) for

clearance to adjacent
corners, drawers,

walls, etc, when
door is open

21" (53.3 cm)

Cutout

Width

28 1/2" (72.4 cm)

_- Min, --)-

28 5/8" (72.7 cm)

==: Max.

Must Be At
Least 28 1/2"

Allow 1" (2.6cm)

minimum for

overlap of oven

top and 1W"

(3.2 cm) overlap

of oven bottom

of cutout

I

51 13/16" (131.6 cm)
Min.

51 15/16" (131.9 cm)
Max

7 3/4"

(19.7 cm Junction Box Cabinet Width

) Location

(junction box Recommended
may be Cutout Location

I

located in
adjacent

cabinet)

/

from Floor

Cutout Depth
Cutout Width

-1

47" (119.4 cm)

Min.

to Bottom of

Junction Box

Cutout Height

NOTE: If the cabinet does not
have a front frame and the sides

are less than 3/4" (1.9 cm) thick,
shim both sides equally to

establish the cutout width.

30" (76.2 cm)

12" (30.5 cm)

23 1/2" (59.7 cm) Min.
28 1/2" (72.4 cm) Min.
28 5/8" (72.7 cm) Max.
51 13/16" (131.6 cm) Min.
51 15/16" (131.9 cm) Max.

i

Recommended
cutout location

Cabinet

Width

If the cabinet does not have a solid bottom,
two braces or runners must be installed

level with the bottom of the cutout to
support the weight of the oven. For

double ovens, the runners and braces
must support 275 Ibs (124 Kg).

NOTE: If marks, blemishes or the
cutout opening are visible above the

installed oven, it may be necessary to

add wood shims under the runners and
front trim until the marks or opening

are covered.

(30.5 cm)

Suitable
Bracing

to Support
Runners --

-_(54, 21 5/8"--_

9 cm) Over \

Centerline
of Cabinet

-- 2" x 4"

(Scm x 10cm)

or equivalent

runners level
with bottom
of cutout

10

Installation instructions

Cutoutfor 30"( 6.2cm)

ng

only nder Counter

For JTP30, JTP70, PT916, PT920, ZET938 models only.

Gas or electric cooktops may be installed over this oven. See
cooktop installation instructions for cutout size. See label on
top of oven for approved cooktop models.

25" (63,5 cm)

,- _ -_ made to the left.

Top and/or side fillers
may be necessary
if unit is positioned
between existing

cabinets. Be sure
they are attached

securely, since they

will anchor the oven
in the cabinet.

28 112" (72.4 cm) Min.
28 518" (72.7 cm) Max.

240V / 208V
Junction Box

Location (junction

box may be in Gas and electrical connections

adjacent cabinet) for 30" (76.2 cm) gas cooktop must

Allow 1" (2.5
overlap top

of oven_

11/16" (1.8 cm)
overlap side edges

of cutout and
1 114" (3.2 cm) -"

overlap bottom
of oven. , ',',

,s_- ;?'

s

Built-inOvens

7 314" be located in an adjacent accessible

(19.7 cm) location to the right. For 36" (91.4 cm)

Max. gas cooktop, the connections may be

r

22" (55.9 cm) Min.
Above Support

Platform

24" (61 cm)

36" (91.4 cm)

Typical

Countertop

Height

Side by Side Installations

Install two wall ovens in separate cutouts.

Allow 2" (5.1 cm) min. between cutouts.

Cutout- ] 2"(5.1 cm)

Observe all| Min.

dimensions_ _ll"'_

and |

requirements.J

11

4" (10.2 cm)

Typical
Toekick

NOTE: This oven is only
approved to be installed under
the specific models as labeled

on this unit.

Cutout -

Observe all

dimensions

and

requirements.

Cabinetry

Cutout for 30"(76.2cm) Single or Double
Built-In Ovens only- Over a

Warming Drawer

For JTP30, JTP35, JTP55, JTP70, JTP75, PT916, PT920, PT956, PT960,

ZET938, ZET958 models only.

Single 30" (76.2 cm)

Oven Over a Warming

Drawer

Rear Wall Per Warming
Drawer Requirement

Per Warming
Drawer

Requirement

1" (2.5 cm) Min. Above Toekick or

Adjust to Oven Installation Height

NOTE: Additional clearances between cutouts

may be required. Check to be sure the oven
supports above the Warming Drawer location
do not obstruct the required interior depth and
height.

Block Against

2" (5.1 cm)
Min.

NOTE: install the
oven only with

specific models
Iisted on the labeI

located on top of
the oven.

Double 30" (76.2 cm)
Oven Over a Warming

Drawer

Anti-Tip Block
Against Rear

Wall Per
Warming

Drawer
Requirement

2" (5.1 cm)

Min.

Per Warming
Drawer

Requirement

1" (2,5 cm) Min. Above Toekick

° When installing a Warming Drawer below

a single or double oven, a separate 120V,
60 Hz, properly grounded receptacle must

be installed. Refer to installation instructions
packed with the Warming Drawer for

specific installation requirements.

12

Cabinetry

[_ Cutoutfor 30"(76.2c_)SingleOvens only-

Belowan Advantiumor :rowave Oven

or Between an Advantium or crowave

Ovenand a rmingDrawer

For JTP30, JTP70, PT916, PT920, ZET938 models only.

Single 30" (76.2 cm) Oven

Below an Advantium or
Microwave Oven

P_Wv

" (5.1 cm) Min.

Note: Install the
oven only with

Requir_

NOTE: The middle rail separating the two

openings may need to be larger than the 2"

(5.1 cm) minimum shown. Always refer to the
individual installation instructions packed with

each product for specific requirements.

Combined Advantium or Microwave
Oven and Wall Oven Installation:

When installed in combination with a
single wall oven, use separate electrical

junction boxes.

• Refer to the Advantium or microwave
oven installation instructions for electrical

requirements of that product.

These connections must be made

by a qualified electrician. All electrical
connections must meet National Electrical

Code or prevailing local codes.

specific models
listed on the label

located on top of
the oven.

Single 30" (76.2 cm) Oven
Between an Advantium or

Microwave Oven and a

Warming Drawer

Per Advantium
Microwave Oven

Requirement

Per Warming

Drawer

Req

NOTE: Additional clearances may be
required. Check to be sure the oven
supports above the Warming Drawer

do not obstruct the required interior depth

and height. The middle rail separating the

openings may need to be larger than the
2" (5.1 cm) minimum shown. Always refer to

the individual installation instructions packed
with each product for specific requirements.

Warming Drawer Combined with
Advantium or Microwave Oven and

Single Oven:

Install a separate 120V, 60Hz, properly

grounded receptacle. See installation

instructions packed with each product

for specific requirements.

2" (5.1 cm) Min.

2" (5.1 cm) Min.

13

Installation Instructions

Electrical Connections

ATTENTION INSTALLER

All electric wall ovens must be hard wired
(direct wired) into an approved junction

box. A plug and receptacle is NOT permitted
on these products.

DO NOT shorten the flexible conduit.
The conduit strain relief clamp must be

securely attached to the junction box
and the flexible conduit must be securely
attached to the clamp. If the flexible
conduit will not fit within the clamp, do not
install the oven until a clamp of the proper

size is obtained.
NOTE TO ELECTRICIAN: The 3 power

leads supplied with this appliance are
UL recognized for connection to heavier
gauge household wiring. The insulation
of these 3 leads is rated at temperatures

much higher than the temperature rating
of household wiring. The current carrying

capacity of the conductor is governed
by the wire gauge and the temperature
rating of the insulation around the wire.

Turn off the circuit breaker or remove
fuses to the oven branch circuit.

With the oven supported on a table or

platform in front of the cabinet opening,

connect the flexible conduit to the
electrical junction box as shown below.

Position the conduit in such a manner

that it will lie on top of the oven in
a natural loop when the oven is

installed. You will need to purchase
an appropriate strain relief clamp to
complete the connection of the conduit
to the junction box.

Junction Box

Location

Conduit I

WARNING: Improper

connection of aluminum house
wiring to copper leads can

result in an electrical hazard or fire.
Use only connectors designed for

joining copper to aluminum and follow

the manufacturer's recommended
procedure closely.

14

oven on a

support to assist i
connecting conduit

Strain Relief Clamp
(not included)

must be used at
Junction Box

Installation Instructions

New Construction and
Four-Conductor Branch

Circuit Connection

• When installing in new construction, or

• When installing in a mobile home, or

• When installing in a recreational vehicle, or

• When local codes do not permit grounding
through neutral:

a. Cut the neutral (white) lead from the crimp.

Re-strip the neutral (white) lead to expose

the proper length of conductor.

b. Attach the appliance grounding lead (green

or bare copper) in accordance with local

codes. If the residence grounding conductor
is aluminum, see WARNING on page 14.

c. Connect the oven neutral (white) lead to

the branch circuit neutral (white or gray)

in accordance with local codes, using a

wire nut.

Three-Conductor Branch

Circuit Connection

When connecting to a three-conductor branch

circuit, if local codes permit:
a. Connect the bare oven ground conductor

with the crimped neutral (white) lead to
the branch circuit neutral (white or gray

in color), using a wire nut.

__ound and

Ln NeutralWires

_J_ JcUnTt_onBox

b. Connect the oven red lead to the branch

circuit red lead in accordance with local
codes, using a wire nut.

c. Connect the oven black lead to the branch

circuit black lead in accordance with local
codes, using a wire nut. If the residence

red, black or white leads are aluminum

conductors, see WARNING on page 14.

d. Install Junction Box Cover.

d. Connect the oven red lead to the branch

circuit red lead and the oven black lead to

the branch circuit black lead in accordance
with local codes, using wire nuts. If the

residence red, black or white leads are
aluminum conductors, see WARNING

on page 14.

e. Install Junction Box Cover.

15

Installation Instructions

lclSecuring the Oven in the Opening

I_ Sliding the Oven Into the

Opening

a. Loop (do not tie) a 36" (91 cm) string

around the conduit before the oven is slid
into place. This will keep the conduit from

falling behind the oven.

Pull out on
string loop
while pushing

the oven into
the cabinet

b. Lift oven into cabinet cutout using the oven

opening as a grip. Carefully push against
oven front frame. Do not push against
outside edges.

Drilling the Pilot Holes and
Mounting the Oven

NOTE: Before drilling the pilot holes,
make sure the oven is pushed as far
back into the opening as it will go

and centered.

i

a,

Drill through the mounting holes (top and
bottom) of the side trim, for the #8 screws
provided.

Mounting

Hole

Locations

(Hole

may vary)

1111_

The screws must

be a minimum of
1/4" (6 mm) from

the front of the
cutout.

i

c. As you slide the oven back, pull the string

so that the conduit will lie on top of the

oven in a natural loop.

d. When you are sure the conduit is out of the

way, slide the oven 3/4 way back into the
opening. Remove the string by pulling on
one end of the loop.

WARNING: Mounting

screws must be used. Failure to

do so could result in the oven

falling out of the cabinet causing
serious injury.

i

b. Secure the oven to cabinet with screws

provided.

NOTE: If the cabinet is particle board, you
must use #8 x 314" particle board screws.

These may be purchased at any hardware

store.

16

Installation Instructions

Preparing for the Bottom

Trim Installation

a. With oven installed, take the bottom trim

and center it on the bottom front edge of

the cabinet opening.

b. Using the trim

as a template,
mark the center

of each slot

(two total) where

the mounting holes
will be drilled.

c. Remove the trim.
d. Drill pilot holes into

the center of each
template mark.

For 27" (68.6 cm)

T_'°_I_P%_&°,_er_lllllllI

Mark (2) Mounting _IIH

Hole Locations _"_'_J_l
here

* Remove models with

Lower Trim Lower Trim in
Before Position, Mark

Pre-drilling (2) Mounting
Mounting Hole Locations

Holes here

"_ For 30" (76.2 cm)

7

Installing the Metal
Bottom Trim

Place the bottom metal trim centered over

a.

the pre-drilled mounting holes. Tape the

edges of the trim down to maintain the
alignment.

b. Using two trim screws provided, secure

the bottom trim to the bottom edge of the

cabinet.

Trim Screw Locations for jTrim
27" (68.6 cm) models with _'-.._J "l'

Lower Trim \ _%."'_))))1 I,

Side \t _]_

IMPORTANT: If this unit is ever
removed from the cabinet or the oven

is ever pulled out for service, the trim
must be removed first or damage to

the trim will occur.

._ _ Side

Trim Screw Locations for

30" (76,2 cm) models with
Lower Trim

17

Installation Instructions

ID-IReplacing the Oven Door

NOTE: The oven door is heavy. You
may need help lifting the door high

enough to slide it into the hinge slots.
Do not lift the door by the handle.

Lift the oven door by
placing one hand on

each side. The door is
heavy, so you may need

help. Do not lift the door
by the handle.

r-_ With the door at the same angle as

the removal position, which is most of
the way closed, seat the notch of the
hinge arm into the bottom edge of the
hinge slot. The notch of the hinge arm
must be fully seated into the bottom

of the slot.

Hinge Arm

Bottom Edge

of Slot

I-_ Open the oven door as far as it

r-_ Push the hinge locks up against the

i

will open.

front frame of the oven cavity, to the

locked position.

Hinge in
Locked Position

Notch of Hinge

Securely Fitted

into Bottom
Hinge Slot

r-_ Close the oven door.

Hinge Notch

18

Installation Instructions

Pre-Test Checklist

I_ emove all protective film, if present,

I_ heck to be sure that all wiring is

and any stickers.

secure and not pinched or in contact

with moving parts.

Operation Checklist

Remove all items from the inside I&JlV

of the oven.

Check that conduit is securely
connected to the junction box.

Turn on the power to the oven. (Refer
to your Owner's Manual.) Verify that
the bake and broil units, and all

cooking functions operate properly.
Check that the circuit breaker is not

tripped nor the house fuse blown.

Check that the bottom trim is installed
properly (see page 17).

Check to be sure the mounting screws
are installed and flush with the side trim

(see page 16).

NOTE TO ELECTRICIAN: The power
leads supplied with this appliance
are UL recognized for connections

to larger gauge household wiring.
The insulation of these leads is

rated at temperatures much higher

than the temperature rating of

household wiring. The current
carrying capacity of a conductor
is governed by the wire gauge and

also the temperature rating of the
insulation around the wire.

NOTE: ALUMINUM WIRING

See your Owner's Manual for

troubleshooting list.

A. WARNING: IMPROPER

CONNECTION OF ALUMINUM

HOUSE WIRING TO THE COPPER
LEADS CAN RESULT IN AN
ELECTRICAL HAZARD OR FIRE.

B. Splice copper wires to aluminum

wiring using special connectors
designed and UL approved for

joining copper to aluminum,

and follow the manufacturer's

recommended connector
procedure closely.

NOTE: Wire used, location and

enclosure of splices, etc., must
conform to good wiring practice

and local codes.

19

Notes

20