GE JT910WAWW Specification

JT910WAWW - GE Profile Performance™30" Single Wall Oven

Specification Revised 8/99

Gas or electric cooktops may be installed over this oven. See cooktop installation instructions for cutout size. See label on top of oven for approved cooktop models.

Gas and electrical connections for gas cooktop must be located in an adjacent accessible location to the right. For a 36" gas cooktop, the connections may be made to the left.

120 Volt Outlet

Gas connection

Junction box location 240/208V

36'' MIN.

4'' To 4-1/2 '' Toe kick allowable

Match toe kick height front and two sides

22'' MIN. above support platform

Top and/or side fillers may be necessary if unit is positioned between existing cabinets

28-1/2'' MIN.

28-5/8'' MAX. 27-1/4'' MIN. 27-5/16'' MAX. Cutout height

3/4'' Support platform required

23-1/2" MIN. Cutout depth

Allow 11/16'' overlap over side edges of cutout

1-1/2" Countertop

Note: Oven is rated for use only under the following cooktops:

• GE 30" and 36" electric coil and CleanDesign cooktops (Excluding Induction)

• GE 30" and 36" gas standard and sealed burner cooktops Note: Gas or electric cooktops may be installed over this oven. See cooktop installation

instructions for cutout size. See label on back of oven for approved cooktop models. Installation Information: Before installing, consult installation instructions [Pub. No. 31-10125]

packed with product for current dimensional data and for alternate installation options.

Undercounter Installation (in inches)

5-9/16"

Reference dim. for

MAX. support height

with typical 36" countertop

height

36" Typical Countertop height

Power cord

Reference 5-9/16

30-7/16

Free space

1-1/2" MIN.

1-1/2" Typical countertop

Side View

27-5/16" MAX.

Cutout height

27-1/4" MIN.

Junction box(s) for

oven & radiant

cooktop 22" from

floor

Add suitable filler

to match adjacent

cabinets when needed

to maintain toe kick

alignment

This installation is to achieve minimum gap between bottom of countertop and control panel.

Note: For this installation, the bottom trim will not be flush with a typical 4" toe kick.

Optional Custom Installation for 30" CleanDesign (Excluding Induction) or Sealed Burner Gas Cooktop (in inches)

Note: Cabinets installed adjacent to wall ovens must have an adhesion spec

of at least 194°

Listed by Underwriters Laboratories

For answers to your Monogram,

GE Profile Performance Series,

™

GE Profile™or GE appliance questions, call GE Answer Center®service, 800.626.2000.

JT910WAWW - GE Profile Performance™30" Single Wall Oven

Specification Revised 8/99

Note: Oven is rated for use only under the

following cooktops:

• GE 30" and 36" electric coil and CleanDesign cooktops (Excluding Induction)

• GE 30" and 36" gas standard and sealed burner cooktops

Note: Gas or electric cooktops may be installed over this oven. See cooktop installation instructions for cutout size. See label on back of oven for approved cooktop models.

Installation Information: Before installing, consult installation instructions [Pub. No. 31-10125] packed with product for current dimensional data and for alternate installation options.

Single Oven Wall-Mount or Cabinet Installation Dimensions (in inches)

Optional Undercounter Installation with 36" Gas Cooktop (in inches)

Power cord for counter unit

Junction box for oven

Junction box in adjacent cabinet for counter unit hook-up

2 (two) 90°elbows & sufficient pipe to connect in adjacent cabinet

Right cabinet side

3/4" Support

Shut-off

valve

Pressure regulator

1/2" Black

iron pipe

Union

Conduit

30" Built-in

oven

3-1/2" MIN. Free space

4" To 4-1/2"

3-1/4

19-1/16" Cutout depth

Side View

Note: These ovens are

not

approved for stackable or side-by-side installations.

Most 30" Wall Cabinets can be used with this unit.

For answers to your Monogram,

GE Profile Performance Series,

™

GE Profile™or GE appliance questions, call GE Answer Center®service, 800.626.2000.

Listed by Underwriters Laboratories

Must Support 200 lbs.

KW Rating

240V 3.6 208V 2.7

Breaker Size

20 Amps

†

Note: Check local codes for required

breaker size.

Note: If a solid bottom is used instead of the runners, a 6" x 10" rectangle must be cut out of the bottom for optimum performance and proper air circulation.

Cut Opening

in Solid Bottom

(Must Support 275 lbs.)

28-1/4

Allow minimum of 21'' for clearance to adjacent corners, drawers, walls, or etc.

A=Allow 1" overlap of oven over top and bottom edges of cutout. B=Allow 11/16"-3/4" for overlap of oven over side edges of cutout.

Conduit

(48" long)

28-1/2'' MIN. 28-5/8'' MAX.

23-1/2'' MIN. Cutout depth

27-1/4'' MIN. 27-5/16'' MAX. Cutout height

Recommended

cutout location

32-1/2"

from floor

Junction box location

22'' MIN.

+ 1 hidden pages