GE JS900BK4BB, JS900CK4CC, JS900SK5SS, JS900WK4WW, JS905BK4BB Installation Guide

Installation

Self-Cleaning Radiant

Electric Slide-In Range

Instructions

I If you have questions, call 1.800.GE.CARES or visit our website at:ge.com I

JSP42, JS968, JS900, JS905

Before You Begin

Read these instructions carefully and completely.

• IMPORTANT-save these

instructions for local inspector's use.

• IMPORTANT-observeall

governing codes and ordinances.

PARTS INCLUDED

2 Screws Screws

MATERIALS YOU MAY NEED

Anti-Tip Bracket

Note to Installer--Be sure to leave these
instructions with the consumer.

Note to Consumer--Keep these
instructions for future reference.

Proper installation is the responsibility
of the installer and product failure due
to improper installation is NOT covered
under warranty.

NOTE--This appliance must be properly
grounded.

TOOLS YOU WILL NEED

1/8" Drill Bit and
Electric or Hand Drill

Level

Wrench or Pliers

(for 1-7/16" Nut)

1/4" Nut Driver

Tin Snips Lag Bolts Anchor Sleeves

(For Anti-Tip Bracket Mounted

on Concrete Floors Only)

(UL Approved 40 or 50 AMP)

4-Wire Cord OR 3-Wire Cord

4' long 4" long

31-10621-2 1-07 JR 1

Squeeze Connector

(For Conduit

Installations Only)

Tape Measure

S

Straight Edge

or Square

Hand or Sabre Saw

Pliers

Pencil

Safety Glasses

Installation Instructions

IMPORTANT SAFETY INSTRUCTIONS

For Your Safety

_i, WARNING: For personal

JnstallatJon.FaJlureto do so could result
Jnserious injury or even death.

All rough-in and spacing dimensions must be
met for safe use of your range. Electricity to the
range can be disconnected at the outlet without
moving the range if the outlet is in the preferred
location (remove lower drawer).

To reduce the risk of burns or fire when reaching
over hot surface elements, cabinet storage
space above the cooktop should be avoided. If
cabinet storage space is to be provided above
the cooktop, the risk can be reduced by installing
a range hood that sticks out at least 5" beyond

the front of the cabinets. Cabinets installed
above a cooktop must be no deeper than 13"

Be sure your appliance is properly installed and
grounded by a qualified technician.

safety, remove house fuse or open
cJrcuJtbreaker before beginning

WARNING: Toreducethe

risk of tipping, the appliance must
be secured by properly installing

the Anti-Tip bracket packed with the

appliance.

If you pull the range out and away from the wall
for any reason, make sure the Anti-Tip bracket is
engaged when the range is pushed back against

the wall.

2

Installation Instructions

Pre-lnstallation Checklist

Inspect Installation Location

Refer to alternate construction section

for the following non-standard

installations.

a.

Counter opening extends to
the wall:

Maintop Filler (supplied with the
range.) (See page 15, section AA,

for Installation Instructions) or

Backguard (Kit JXS36XX or

JXS39SS). See page 15.

b.

Counter height greater than
36-3/4":

Lower Trim Slide-In (Kit JXS56XX).

c.

One side is not enclosed by
a cabinet:

Bodyside (Kit JXS76XX).

d. Island Installation:

To provide an optimum installation,
the top surface of the countertop

must be level and flat (lie on the
same plane) around the 3 sides
that are adjacent to range cooktop.

Proper adjustments to make the
top flat should be made or gaps

between the countertop and range
cooktop may occur. Forcing the
cooktop to fit may cause excessive
gaps and could break the glass
and void the warranty.

To obtain Kits:
a. Visit GE Web Site (See page 1)

b. Call GE Answer Center (See page 1)
c. Contact Dealer

Move range indoors in front of
cabinet opening.

(Do not use hand trucks when
moving the unpackaged range.
Cooktop glass may be broken.)

Protect the kitchen flood Flatten and
place a piece of the shipping carton in

front of the installation location to
protect the flooring.

Do not remove the protective
channel from the sides of the glass
cooktop, if applicable, until later in

the installation.

Protective
Channel

Carefully, tilt the range to access the

range leveling legs. Use an adjustable
wrench to screw leveling legs out so
that glass support flanges clear top of
countertop.

3 (Continued on following page)

Installation Instructions

Pre-lnstallation Checklist cont.

Door removal is not a requirement for
installation of the product, but is an

added convenience. To remove the door:

Open the oven door as far as it will go.

Push both hinge Hinge
locks down toward _,, Position

the door frame, ;iontge

to the unlocked
position. This may
require a flat blade Hinge

screwdriver. Arm

DO NOT LIFT THE DOOR

BY THE HANDLE!

Place hands on both sides of
the door, and close the oven
door to the removal position.

This is half way between the
broil stop and fully closed.

U_locked

Storage Drawer Removal

Pull the drawer out until it stops.

Lift the front of the drawer until the
stops clear the guides.

Rail

Pull forward and remove the drawer.

[_ Liftdoor up and

NOTE: The oven door is very heavy.
Be sure you have a firm grip before lifting

the oven door off the hinges. Use caution

once the door is removed. Do not lay the
door on its handle. This could cause dents

or scratches.

[_i1_' Remove packing materials. Remove

out until the
hinge arms

clear the slots.

Hinge Clears Slot

labels on door, plastic on trim and panel,
and all tape around the range.

4

Installation Instructions

Pre-lnstallation Cutout

and Required Clearances

OVERALL DEPTH

{_ 27-1/2"

If cabinets are placed less than 30" above the
range, see Alternate Construction, section AF,
on page 16.

30" ranges conform to U.L. requirements
for 0" spacing from vertical walls below
countertops. Allow 1/4" minimum clearance
at the back wall above the countertop.

Wall coverings, counters and cabinets around
range must withstand heat (up to 194°F)
generated by the range.

Follow instructions
packaged with alternate 30" Mir

appliance.

For Optimum

Installation These
Surfaces Must

Be Flat & Level

36"

countertop

Electrical

Outlet Area

i _3_'i *'-_

_-" 15" Min. vertical

/ Countertop

distance from the
bottom of the adjacent

overhead cabinets

Depth 25"

1-114" Min. Countertop

to top of drawer

Shave Raised Edge
To Clear 31-1/8"

Wide Control Panel

5

Installation Instructions

Standard Installation

I-2--1STAN DARD INSTALLATION

f

1t4" Min.

Flat

9t16" Min.

Flat

I

29-15t16"- 30-1/16" "_1

Smooth Cut

Flat

Area

If the construction of your cabinet cannot
provide a 1/4" flat area at the back of the
countertop opening, consider changing the
countertop to accommodate this dimension.

See Alternate Construction section. If the area II_1
is not flat, excess tension may be applied to

the glass cooktop, causing breakage and
voiding the warranty. [-_

I_.C_l

[_ Remove countertop raised edge, if

Center the 30" wide opening over the
adjacent cabinets and mark with a
straight edge.

Using a straight edge, mark the back line

at 23-3/16" from the front edge of the
counter.

Be careful not to damage the adjacent

cabinets while cutting the countertop.

Use a hand or saber saw to make

straight smooth cuts.

incorporated. (See illustration on page 5)

6