GE JRP15BW1BB, JRP15BW2BB, JRP15BW3BB, JRP15BW5BB, JRP15BW6BB Installation Guide

INSTALLATION INSTRUCTIONS FOR YOUR NEW

24"BUILT-INOVEN

Before you begin - Read these instructions completely and carefully.

IMPORTANT - Save these instructions for local inspector's use.
IMPORTANT - OBSERVE ALL GOVERNING CODES AND ORDINANCES.

Note to Installer - Be sure to leave these instructions with the Consumer.
Note to Consumer - Keep these instructions with your Use and Care Book for future

reference.

Be sure your oven is installed properly by a qualified
installer or service technician.

• Be sure the oven is securely installed in a cabinet

that is firmly attached to the house structure.
Weight on the oven door could cause the oven to
tip resulting in serious personal injury or death.

Never allow anyone to climb, sit, lean, stand, or
hang on the oven door.

• The wall coverings, countertop and cabinets

around the oven should be able to withstand the
heat (up to 200°F) generated by the oven.

1/8" Drill Bit
Electric or Hand Drill
Flat Blade screwdriver

Cabinet space must be provided to enclose the

recessed partofyour built-in oven. SINGLE OVEN

Ruler
Ha nd or saber saw

Pencil

IN STALLATI ON i See Figure I for all necessary

dimensions. DOU BLE OVEN INSTALLATION
i See Figure 2 for all necessa_j dimensions. It is

best to make a template to insure accurate cutting.
Place the bottom of the template on a level base line,
above the floor. See dimension E in Figure I (Single

Oven) or Figure 2 (Double Oven).

It is important that the oven be installed at or above
the minimum height specified. The unit has been

tested and approved, in accordance with safety
standards, at this height.

Pub. No, 31-10241

INT224-14

CAUTION: The electrical power to

the oven supply line must be shut
off while connections are being

made. Failure to do so could result

in serious injury or death.

This appliance must be supplied with the proper

voltage and frequency, and connected to an
individual, properly grounded branch circuit,

protected by a circuit breaker or fuse having
amperage as noted on rating plate. (Rating plate
is located on oven frame.)

We recommend you have the electrical wiring and

hookup of your oven done by a qualified electrician.

After installation, have the electrician show you

where your main range disconnect is located.

Check with your local utilities for electrical codes

which apply in yourarea. Failuretowireyour range
according to governing codes could result in a

hazardous condition. If there are no local codes,
your range must be wired and fused to meet the

requirements of the National Electrical Code, ANSI/

NFPA No. 70-Latest Edition. You can geta copyof

the National Electrical Code, ANSI/NFPA NO. 70-

Latest Edition by writing:

National Fire Protection Association

Battery March Park

Quincy, MA 02269

Effective January 1, 1996, the National Electrical
Code requires that new, but not existing,

construction utilize a 4 conductor connection to an
electric range. When installing an electric range in

new construction, follow the instructions in NEW

CONSTRUCTION AND FOUR-WIRE CORD
CONNECTION KIT.

You must use a three-wire, single-phase A.C.

208Y/120 Volt or 120/240 Volt, 60 Hertz electrical

system. If you connect to aluminum wiring, properly
installed connections approved for use with
aluminum wiring must be used.

Fig. I m SINGLE 0 VEN

NOTE' Locate an approved junction box in the

suggested location, a minimum of 23 7/8" above the
runners,

Be sure the oven support is solid enough to support 90
pounds. Also be sure the oven support is level and
straight. There is no way to level the oven after
installation.

If a solid bottom is used instead of runners, a 6" x 10"
rectangle must be cut out of the bottom (See Fig. 1 ) for

optimum performance and proper air circulation.

DIMENSIONS

2"x4" OR

A. Cabinet Width

B. Cutout Width

C. Cutout Height

U. Cutout Depth
E. Cutout Location

m. Overall Height

W. Overall Width

24"

22 1/2"
27 5/8" Min. 28 1/8" Max.

23 1/2" Min.

32 1/2"

28 3/16"
23 3/4"

Fig. 2 _ DOUBLE OVEN

NOTE: Locate an approved junction box in the

suggested location, a minimum of 48"above the runners.

Be sure the oven support is solid enough to support 155
pounds. Also be sure the oven support is level and
straight. There is no way to level the oven after

installation.

If a solid bottom is used instead of runners, a 6" x 10"
rectangle must be cut out of the bottom (See Fig. 2) for
optimum performance and proper air circulation.

DIMENSIONS

/ 9" l _ E_UNALIENT

2"x4"OR

i"II1 111

A. Cabinet Width

B. Cutout Width

C. Cutout Height

U. Cutout Depth
E. Cutout Location

m. Overall Height

W. Overall Width

24" Min.
22 1/2"

48 1/8"
23 1/2" Min.

12 3/4" Min.
48 3/4"
23 3/4"