I Iinstallation 130"ElectricCooktop
nstructlons _,0, JP355, JP910, JP930, JP940, JP950
I r_ ,,if you have questions, call 800.GE.CARES or visit our website at:www.GEAppliances.com" I
BEFORE YOU BEGIN
Read these instructions completely
and carefully,
• IMPORTANT - Savethese
instructions for local inspector's use.
• IMPORTANT - Observeall
governing codes and ordinances.
• Note to Installer - Be sure to leave these
instructions with the Consumer.
• Note to Consumer - Keep these
instructions for future reference.
• Product failure due to improper installation
is not covered under the Warranty.
-&WARNING - This appliance must
be properly grounded.
• ATTENTION INSTALLER -
ALL COOKTOPS MUST BE HARD WIRED
(DIRECT WIRED) INTO AN APPROVED
JUNCTION BOX. A "PLUG AND
RECEPTACLE" IS NOT PERMITTED ON
THESE PRODUCTS.
• Proper installation is the responsibility
of the installer and product failure due to
improper installation is NOT covered under
warranty.
MATERIALS YOU WILL NEED
Junction Box Wire Nuts
TOOLS YOU WILL NEED
Pencil
Saber Saw
Phillips Head
Screwdriver
1/8" Drill Bit & Electric
or Hand Drill
Ruler or Straightedge
Safety Glasses
PARTS INCLUDED
2 Hold Down
Brackets
4 Screws
31-10603 (12-04 JR) 1
Foam Tape
Installation Instructions
IMPORTANT SAFETY INSTRUCTIONS
FOR YOUR SAFETY
• For Personal Safety, remove house fuse
or open circuit breaker before beginning
installation. Failure to do so could result
in serious injury or death.
• Be sure your cooktop is installed properly
by a qualified installer or service technician,
• To eliminate the risk of burns or fire due
to reaching over heated surface elements,
cabinet storage located above the surface
units should be avoided. If cabinet storage
space is to be provided, the risk can be
reduced by installing a range hood that
projects horizontally a minimum of 5"
beyond the bottom of the cabinets. Cabinet
installation above the cooktop may be no
deeper than 13".
• Make sure the cabinets and wall coverings
around the cooktop can withstand the
temperatures (up to 200°F) generated
by the cooktop.
• The cooktop should be easy to reach and
lighted with natural light during the day.
• Always disconnect the electrical service to
the cooktop before repairing or servicing
the cooktop. This can be done by
disconnecting the fuse or circuit breaker.
Failure to do this could result in a
dangerous or fatal shock. Know where your
main disconnect switch is located. If you do
not know, have your electrician show you.
ELECTRICAL REQUIREMENTS
This appliance must be supplied with the
proper voltage and frequency, and connected
to an individual, properly grounded branch
circuit, protected by a circuit breaker or a
time delay fuse as noted on rating plate.
We recommend you have the electrical wiring
and hookup of your cooktop connected by a
qualified electrician. After installation, have
the electrician show you where your main
cooktop disconnect is located,
Wiring must conform to National Electrical
Code. You can get a copy of the National
Electrical Code, ANSI/NFPA No. 70-Latest
Edition, by writing:
National Fire Protection Association
Batterymarch Park
Quincy, MA 02269
The cooktop conduit wiring is approved for
copper wire connection only, and if you have
aluminum house wiring, you must use
special UL approved connectors for joining
copper to aluminum.
You must use a two-wire, three conductor
208/240 VAC, 60 Hertz electrical system. A
white (neutral) wire is not needed for this
unit. The cooktop must be installed in a
circuit that does not exceed 125 VAC nominal
to ground.
Refer to the rating plate on your cooktop for
the KW rating for your cooktop.
2
Installation Instructions
PRE-INSTALLATION CHECKLIST
- WARNING - The electrical power
to the cooktop supply line must be shut off
while connections are being made. Failure to
do so could result in serious injury or death.
[_ When preparing cooktop opening, make
sure the inside of the cabinet and the
cooktop do not interfere with each other.
(See section on preparing the opening.)
[_ Remove packaging materials and
literature package from the cooktop
before beginning installation.
_Literature
Styrofoam _--Package
Packaging
Coo
I_1 Remove Installation Instructions from
literature pack and read them carefully
before you begin.
Be sure to place all literature, Owner's
Manual, Installations, etc. in a safe place
for future reference.
30"¢_
i:= :_
IN
Make sure you have all the tools and
materials you need before starting the
installation of the cooktop.
@
Your home must provide the adequate
electrical service needed to safely and
properly use your cooktop. (Refer to
section on electrical requirements.)
N1
When installing your cooktop in your
home, make sure all local codes and
ordinances are followed exactly as
stated.
Make sure the wall coverings, countertop
and cabinets around the cooktop can
withstand heat (up to 200°F) generated
by the cooktop.
3
Installation Instructions
PREPARING THE OPENING
[_ The following MINIMUM clearance
dimensions must be maintained.
13" MAX. Depth of uprotected
overhead cabinets
1-1/2" MIN.
Clearance from
cutout to side
wall on the right
of the unit
18" MIN. Height
/'from countertop
to nearest
cabinet on either
side of unit
If a 30" clearance between the cooking
surface and overhead combustible materials
or metal cabinets cannot be maintained, a
minimum clearance of 24" is required and
the underside of the cabinets above the
cooktop must be protected with not less
than 1/4" insulating millboard covered with
sheet metal not less than 0.0122" thick.
OVERALL COOKTOP
DIMENSIONS
CUTOUT DIMENSIONS
OF THE COUNTERTOP
To insure accuracy, it is best to make a
template when cutting the opening in
the counter.
dth of cut
1-3/4" Min. Between _ cut _TZ _J I
cutout and the wall __ _11
behind the cooktop /--I_ !1
2-1/2 '_Min. III
from front edge
of cutout and
front edge of
countertop
JXTR32X CUTOUT FILLER TRIM KIT:
A filler trim kit is available for use if
your countertop cutout is larger than the
dimensions shown, up to 29-13/16" x
20-7/16". Order JXTR32X to reduce the cutout
opening for installation of this cooktop. This
kit may be ordered from your GE Dealer.
JXFLM2XX FLUSH INSTALLATION KIT:
A flush mount installation kit is available
for use in a flush mount or recessed cooktop
installation. Order JXFLM2XX from your
GE Dealer.
9-3/4" _'_'_ CurvedFront Models)
_"_"_'_'_1 _ 3-1/4"Front
Cooktop _--_'_ 4-5/8" Rear
• "_" V 28_ 6-1/4" Rear on
19-1/4" ._.._ Model JP950
20-7/8" (21-1/2" Max. on
" _"_ at the conduit
• location
E_ Five inches (5")
minimum vertical
clearance between
the cooktop bottom
and any combustible
5" Min._
Vertical Clearance
surfaces.
F'_ Make sure the wall coverings, countertop
and cabinets around the cooktop can
withstand heat (up to 200°F) generated
by cooktop.
__ Ce_Veri_lg'
countertop must I
withstand heat f
I_up t° 200°R
4
Installation Instructions
INSTALLING THE COOKTOP
_-I INSTALLING THE
JUNCTION BOX
Install an approved junction box where it will
be easily reached through the front of the
cabinet where the cooktop will be located.
The cooktop conduit is 3 feet long.
I 16_
I Min.
,#-
Installjunction box so
that it can be reached
through the front of
the cabinet,
q
[] ATTACH FOAM TAPE
Apply the foam tape around the outer edge
of the glass. Do not overlap the foam tape.
Bottom of Cooktop
__j_- _. - _ ....
op
_-I LOCATE MOUNTING PARTS
Remove the hold down brackets and screws
from the literature package.
Mounting Screw
A IMPORTANT: The junction box
must be located where it will allow
considerable slack in the conduit for
serviceability.
_-1 PROTECT SURFACE
OF COOKTOP
Place a towel or tablecloth onto the
countertop. Lay the cooktop upside down
onto the protected surface.
Cloth under Cooktop
[] ATTACH BRACKETS
TO COOKTOP
Screw the hold down bracket to the side
of the cooktop unit. Repeat for opposite side
of cooktop.
of Cooktop
Bottom _/1_,_
" . . Hold Down
Cooktop Glass Bracket
Pre-Drilled Hole_
Foam Tape
5
Installation Instructions
INSTALLING THE COOKTOP (CONT.)
[] INSERT COOKTOP
INTO CUTOUT
Insert the cooktop centered into the cutout
opening. Make sure the front edge of the
countertop is parallel to the cooktop. Make
final check that all required clearances
are met.
Hold Down
Bracket
[] ATTACH HOLD DOWN
BRACKETS TO CABINET
Open the cabinet door and screw the hold
down brackets to the cabinet sides with the
screws provided.
Mounting
Cabinet Side
Burner Box Sides
Use suitable fasteners
for anchorage in
cabinet sides
6
Installation Instructions
INSTALLATION--ELECTRICAL CONNECTIONS
[] When making the wire connections, use
the entire length of conduit provided.
The conduit must not be shortened.
[] With the cooktop in place, open the front
of the cabinet door.
[] Insert the wires from the conduit through
the opening of the junction box.
Strain Relief Clamp
GroundRe___
Black
[] Connect the red and black leads from the
cooktop conduit to the corresponding
leads in the junction box.
Red
Ground wire Black
location
[] Once the connections are made, secure
wires together using wire nuts.
Red
Clamp
Strain Relief
Grouna / - Black
GROUNDING INSTRUCTIONS:
The bare ground wire in the conduit is
connected to the cooktop frame. Effective
January 1, 1996, the National Electrical Code
will not permit grounding through neutral.
If used in new construction after January 1, 1996
or in a mobile home, recreational vehicle or
if local codes do not permit grounding
through the neutral white lead, attach the
appliance grounding lead (green or copper)
to the residence grounding conductor (green
or bare copper) in accordance with local
codes. When connecting to a 3 conductor
branch circuit, if local codes permit, connect
the bare ground connector lead of the
cooktop to the branch circuit neutral (gray
or white in color).
A IMPORTANT: Ifthecooktop is
being installed into a blind counter (one with
no cabinet opening below), wire connections
must be made before putting the cooktop
into the cutout opening.
CHECKLISTS
Installation Instructions
Ill PRE-TEST CHECKLIST
[] Remove all protective film, if present,
and any stickers.
[] Check to be sure that all wiring is secure
and not pinched or in contact with
moving parts.
[] Check level of appliance.
[] Check that the cooktop is properly
grounded.
OPERATION CHECKLIST
Remove all items from the top
of the cooktop surface.
[] Turn on the power to the cooktop.
(Refer to your Owner's Manual.) Verify
that all surface burners operate properly,
[] Check that the circuit breaker is not
tripped nor the house fuse blown.
[] Check that conduit is securely connected
to the junction box.
[] See Owner's Manual for
troubleshooting list.
NOTE TO ELECTRICIAN:
The power leads supplied with this appliance
are UL recognized for connections to larger
gauge household wiring. The insulation of
these leads is rated at temperatures much
higher than the temperature rating of
household wiring. The current carrying
capacity of a conductor is governed by the
wire gauge and also the temperature rating
of the insulation around the wire.
NOTE: ALUMINUM WIRING
• WARNING:
IMPROPER CONNECTION OF ALUMINUM
HOUSE WIRING TO THE COPPER LEADS
CAN RESULT IN A SERIOUS PROBLEM.
• Splice copper wires to aluminum wiring
using special connectors designed and
UL approved for joining copper to
aluminum and follow the manufacturer's
recommended connector procedure
closely.
NOTE: Wire used, location and enclosure of
splices, etc., must conform to good wiring
practice and local codes.
8
Loading...