Page 1
JP385BD/WD – GE Select-Top™Modular Downdraft Cooktop
Built-In Downdraft Modular Cooktop
Dimensions (in inches)
Specification Created 6/02
Built-In Downdraft Modular Cooktop Cabinet
Dimensions (in inches)
Receptacle Location: Install an approved
junction box within shaded area shown in
diagram. Junction box must be at least 10-1/2"
below top of cabinet.
Installation Information: Before installing,
consult installation instructions packed with
product for current dimensional data.
GE Appliances
R
Listed by
Underwriters
Laboratories
For answers to your Monogram,® GE Profile™or
GE appliance questions, visit our website at
GEAppliances.com or call
GE Answer Center®service, 800.626.2000.
21-9/16
3
19
6"
Dia.
20-1/2
28-7/8
27-1/2
29-7/8
12-1/4
6
20
9
4
10-1/2
16
C
L
Page 2
Specification Created 6/02
JP385BD/WD – GE Select-Top™Modular Downdraft Cooktop
Cutout Dimensions (in inches)
Note: In some cabinets, the sides may need to be scooped or cut down 2" as shown and the corner
braces removed in order to accommodate the cooktop.
Wall Installation: Wall installations require 25" countertop depth. When cabinet is flush against
the wall, the fan housing can be rotated to the horizontal position for direct venting through rear
wall. Make a countertop cutout that is centered in the range cabinet according to unit dimensions
and installation type. Duct hole is positioned in back of cabinet for through-the-wall ducting.
Peninsula or Island Installation: For peninsula or island installation, a minimum 26" countertop
depth is suggested. Blower should be in vertical position. Island or peninsula cabinets may require
adjustment in cutout depth and/or location within the width dimensions. Duct hole is positioned in
bottom of cabinet for island or peninsula installation.
Slab Installation: For peninsula or island installation and rear wall ducting, PVC duct or locallyapproved piping should be used if installing under a poured concrete slab.
Installing the Ductwork: Use minimum 26-gauge galvanized or 24-gauge aluminum duct in 6"
round or 3-1/4" x 10" size, or combination of both.
PVC duct or locally approved piping should be used if installing under a poured
concrete slab.
Preparing the Cabinet for Installation
25
1-7/8"
MIN. Required*
20-5/8
28-7/8
*U.L. Requirement.
Note: A 6" minimum spacing to adjacent side wall is required
2" Approx.
5" Approx.
for European
cabinets
9-3/8
7-9/16
Downward venting
(in inches)
9-3/8
15-3/4
Rear wall venting (in inches)
GE Appliances
R
Listed by
Underwriters
Laboratories
For answers to your Monogram,® GE Profile™or
GE appliance questions, visit our website at
GEAppliances.com or call
GE Answer Center®service, 800.626.2000.
Page 3
Specification Created 6/02
JP385BD/WD – GE Select-Top™Modular Downdraft Cooktop
Venting Options
Inside Wall
Through Roof
Direct to Outside
Straight Duct
Between the Floor Joists
Through the Cabinet Toe Space
Note: Ductwork must be vented to outside. Do not
vent into a wall, ceiling, crawlspace, attic or any
concealed space. Always use an appropriate roof or
wall cap with damper. Laundry-type wall caps
should never be used. For maximum efficiency
use, the shortest and straightest duct run possible,
with as few fittings as possible. For satisfactory
performance, the duct run should not exceed 100 feet
equivalent length. Refer to the table of equivalent
lengths for various duct configurations.
Installation Information: Before installing, consult
installation instructions packed with product for
current dimensional data.
KW Rating
240V 8.0
Breaker Size
40 Amps
†
†
Note: Check local codes for required breaker size
GE Appliances
R
Listed by
Underwriters
Laboratories
For answers to your Monogram,® GE Profile™or
GE appliance questions, visit our website at
GEAppliances.com or call
GE Answer Center®service, 800.626.2000.
Page 4
Models
Specification Created 6/02
JP385BD/WD – GE Select-Top™Modular Downdraft Cooktop
M
E
D
M
E
D
Features and Benefits
• 30" Single Modular Cooktop
• Fixed 6" and 8" Plug-In Calrod®Heating Elements
• Infinite Heat Rotary Controls
• Powerful Downdraft Venting System
• Heating Element “ON” Indicator Light
• Porcelain-Enameled Cooktop
• Left Side Accepts Optional Cooking Modules
• Single-Speed Downdraft Vent Fan
• Optional Modules Available At Additional Cost
• Model JP385WD – White on white
• Model JP385BD – Black on black
GE Appliances
Optional modules
(available at additional cost) JP385WD JP385BD
Calrod®modules JXDC44RWH JXDC43RBL
Ribbon modules JXDR50VW JXCDR50VB
Grill modules JXDL44N JXDL44N
Griddle Accessory JXDD44R JXDD44R
Grill Cover JXDM3 JXDM2
Loading...