Before using your range,
read this book carefully.
It is intended to help you
operate and maintain your new
range properly.
Keep it handy for answers to
your questions.
If you don’t understand something
or need more help, write (include
your phone number):
Consumer Affairs
GE Appliances
Appliance Park
Louisville, KY 40225
Write down the model
and serial numbers.
You’ll find them on a label
behind the range door.
These numbers are also on the
Consumer Product Ownership
Registration Card that came with
your range. Before sending in
this card, please write these
numbers here:
Model Number
Serial Number
Use these numbers in any
correspondence or service calls
concerning your range.
If you received
a damaged range . . .
Immediately contact the dealer (or
builder) that sold you the range.
Save time and money.
Before you request
service...
Check the Problem Solver in the
back of this book. It lists causes of
minor operating problems that you
can correct yourself.
IF YOU NEED SERVICE...
To obtain service, see the
Consumer Services page in
back of this book.
We’re
uroud
of our service and
.
want you to be pleased. If for some
reason you are not happy with thewrite all the details—includingChicago, IL 60606
service you receive, here are three
steps to follow for further
the
help.
FIRST, contact the people who
serviced your appliance. Explain
why you are not pleased. In most
cases, this will solve the problem.
NEXT, if you are still not pleased,
your phone number—to:
Manager, Consumer Relations
GE Appliances
Appliance Park
Louisville. KY 40225
not resolved, write:
Major Appliance Consumer
Action Panel
20 North Wacker Drive
INIPORTANT
SAFETY INSTRUCTIONS
Read all instructions before using this appliance.
When
using electrical appliances, basic safety
precautions should be followed, including the
following:
●
Use this appliance only for its intended use as
described in this manual.
●
Be sure your appliance is properly installed
and grounded by a qualified technician in
accordance with the provided installation
instructions.
●
Don’t attempt to repair or replace any part of
range
your
recommended in this book.
unless it is specifically
All
other servicing
should be referred to a qualified technician.
“
Before performing any service, DISCONNECT
THE
RANGE
HOUSEHOLD
THE CIRCUIT BREAKER.
POWER SUPPLY AT THE
DISTRH3UTION
PANEL
BY
Page 3
●
Do not leave children alone-children should
not be left alone or unattended in an area where an
appliance is in use. They should never be allowed
to sit or stand on any part of the appliance.
●
Don’t allow anyone to climb, stand or hang on
the
door
or cooktop. They could damage the
range or cause severe personal injury.
●
CAUTION: ITEMS OF INTEREST TO
CHILDREN SHOULD NOT BE STORED IN
CABINETS ABOVE A RANGE OR ON THE
BACKSPLASH OF A RANGE-CHILDREN
CLIMBING ON THE RANGE TO
ITEMS COULD
●
Teach children not to play with the controls or
BE SERIOUSLY INJURED.
REACH
any other part of the oven.
●
Never leave the oven door open when you are
not watching the range.
●
Do not store flammable materials in an oven or
near the cooktop.
. Never wear loose-fitting or hanging garments
while using the appliance. Flammable material
could be ignited if brought in contact with hot
heating elements and may cause severe burns.
●
Use only dry pot holders—moist
or damp pot holders on hot surfaces
may result in bums from steam. Do
not let pot holders touch hot heating elements. Do
not use a towel or other bulky cloth.
●
For your safety, never use your appliance for
warming or heating the room.
●
DO NOT STORE OR USE COMBUSTIBLE
MATERIALS, GASOLINE OR OTHER
FLAMMABLE VAPORS AND LIQUIDS IN
THE VICINITY OF THIS OR ANY OTHER
APPLIANCE.
4
‘ : J’
&
●
Do not use water on grease fires.
Never pick up a flaming pan.
Smother flaming pan on surface unit
by covering pan completely with well-fitting lid,
cookie sheet or flat tray, or if available, use dry
chemical or foam-type extinguisher.
Flaming grease outside a pan can be put out by
covering with baking soda or, if available, a multipurpose dry chemical or foam-type fire
extinguisher.
Flame in the oven can be smothered completely
by closing the oven door and turning the oven
control to OFF or use a dry chemical type
extinguisher.
●
Do not touch heating elements or interior
surface of oven. These surfaces maybe hot
enough to burn even though they are
,dark
in color.
During and after use, do not touch, or let clothing
or other flammable materials contact surface units,
areas nearby surface units or any interior area of
the oven; allow sufficient time for cooling first.
Potentially hot surfaces include the cooktop, areas
facing the cooktop, oven vent opening, surfaces
near the opening, crevices around the oven door
and metal trim parts above the door. Remember:
The inside surface of the oven maybe hot when
the door is opened.
●
When cooking pork, follow the directions
exactly and always cook the meat to an internal
temperature of at least
170”F.
This assures that, in
the remote possibility that trichina may be present
in the meat, it will be killed and the meat will be
safe to eat.
●
After broiling, always take the broiler pan
out of the range and clean it. Leftover grease
in the broiler pan can catch fire next time you
use the pan.
●
Keep hood and grease filters clean to maintain
good venting and to avoid grease fires.
●
Do not let cooking grease or other flammable
materials accumulate in or near the range.
—
Oven
●
Stand away from range when opening oven
door. Hot air or steam which escapes can cause
burns to hands, face and/or eyes.
●
Don’t
heat unopened food containers. Pressure
could build up and the container could burst,
causing an injury.
(continued next page)
3
Page 4
1
●
IMPORTANT SAFETY INSTRUCTIONS
5-
●
Keep oven vent unobstructed.
●
Keep oven free from grease buildup.
●
Place oven shelf in desired position while oven
is cool. If shelves must be handled when hot, do
not let pot holder contact heating units in the oven,
●
Pulling out shelf to the shelf stop is a
convenience in lifting heavy foods. It is
precaution against burns from touching hot
surfaces of the door or oven walls.
●
When using cooking or roasting bags in oven,
follow the manufacturer’s directions.
●
Do not use your oven to dry newspapers. If
overheated, they can catch fire.
●
Do not use oven for a storage area. Items stored
in an oven can ignite.
●
Do not leave paper products, cooking utensils,
or food in the oven when not in use.
also
a
(continued)
Q
To minimize the possibility of burns,
of flammable materials, and spillage, the handle
of a container should be turned toward the center
of the range without extending over nearby
surface units.
●
Always turn surface unit to OFF before
removing cookware,
Q
Keep an eye on foods being fried at HI or
MEDIUM HIGH heat settings.
●
To avoid the possibility of a burn or electric
shock, always be certain that the controls for
all surface
coils are cool before attempting to lift or
remove the
●
Don)t
units. Don’t put them in a dishwasher.
●
When flaming foods are under the hood, turn
the fan off. The fan, if operating, may spread
the flame.
ignition
units
are at OFF position and all
unit.
immerse or soak removable surface
Surface Cooking Units
.
~>-.
q
cover the surface unit heating element. The use of
undersized cookware will expose a portion of the
heating element to direct contact and may result in
ignition of clothing. Proper relationship of
cookware to burner will also improve efficiency.
Q
Never leave surface units unattended at high
heat settings.
greasy spillovers that may catch on fire.
●
Be sure drip pans are not covered and are in
place. Their absence during cooking could
damage range parts and wiring.
●
Don’t use aluminum foil to line drip pans or
anywhere in the oven except as described in this
book. Misuse could result in a shock, fire hazard
or damage to the range.
●
Only certain types of glass, glass/ceramic,
earthenware or other glazed containers are
suitable for cooktop service; others may break
because of the sudden change in temperature. See
section on Surface Cooking for suggestions.
Use proper pan size—This
appliance
is
equipped
with different
size surface units. Select cookware
having flat bottoms large enough to
Boilover
causes smoking and
●
Never clean the cooktop surface when it is
hot.
Some
cleaners produce
noxiotis
fumes and
wet cloths could cause steam burns if used on a
hot surface.
●
Foods for frying should be as dry as possible.
Frost on frozen foods or moisture on fresh foods
can cause hot fat to bubble up and over sides
of pan.
●
Use little fat for effective shallow or deep-fat
frying. Filling the pan too full of fat can cause
spillovers when food is added.
●
If a combination of oils or fats will be used
in frying, stir together before heating, or as fats
melt slowly.
●
Always heat fat slowly, and watch as it heats.
●
Use deep fat thermometer whenever possible to
prevent overheating fat beyond the smoking point.
●
Never try to move a pan of hot fat, especially a
deep fat fryer. Wait until the fat is cool.
SAVE
THESE INSTRUCTIONS
4
Page 5
FEATURES OF YOUR RANGE
1
Feature Index
1 Model and Serial Number
2
Broil Unit
3 Oven Vent
‘4
Surface Unit Controls
=Surface
Indicator Light
6 Lift-Up Cooktop
it up to simplify cleaning underneath)
7
Plug-In Surface Units
8 Oven Set Light
when you set Bake, Broil, or Timed
Bake, on some models.)
9
Oven Set Knob
10 Automatic Clock and Timer
(on some models)
11
Drip Pans
Unit “ON”
(support rods hold
(The light comes on
Explained
on page
2
—
6, 19
6
18
I
19
11
9, 19
8
19
Feature Index
12 Oven Light Switch
(lets you turn oven light on and off)
13 Automatic Oven Light Switch
(Turns oven on automatically when
door is opened.)
14 Oven Cycling Light
glows until oven reaches your selected
temperature, then goes off and on
with the oven unit during cooking.)
15
Oven Temp Knob
16 Oven Interior Light
17 Oven Shelf Supports
18 Oven Shelves
19 Bake Units
20 Removable Oven Door with
Broil Stop position (Easily
removed
21
Broiler Pan and Rack
for oven cleaning. )
(The oven light
Explained
on page
9
9
11
9, 19
9,21
9
9,21
3
20
16,21
5
Page 6
SURJ?ACE
At both OFF and HI the control “clicks” into position. You may hear slight
“clicking” sounds during cooking, indicating the control is keeping the unit
at the heat level or power level you set.
COOKING
How to Set the Controls
Push the knob in and turn in either direction to the heat setting you want.
Be sure you turn control to OFF when you finish cooking. The surface unit
indicator light will glow when ANY heat on any surface unit is on.
Heat Setting Guide
HI—Used to begin cooking or to bring water to a
boil. Reduce heat setting after water boils.
MEDIUM HIGH—(Setting halfway between HI and
MED) Maintains a fast boil on large amounts of food.
MED—Saute and brown; keeps food at a medium
boil or simmer.
MEDIUM LOW—(Setting halfway between MED
and LO) Cook after starting at HI; cooks with little
water in covered pan.
LO—Used for long slow cooking (simmering) to
tenderize and develop flavors. Use this setting to melt
butter and chocolate or to keep foods warm.
NOTE: Surface Indicator Light may glow between
LO and OFF, but there is no power to the surface units.
MEDIUM *
LOW
1+ n
III
+
F-
LO
\
\
‘
-
a)-
/
Ill
❑ 0
;;F
MED
HI
/
0
‘
w MEDIUM
\
HIGH
COOKING TIPS
Cookware
● Use medium-or heavy-weight cookware. Aluminum
cookware conducts heat faster than other metals.
Cast-iron and coated cast-iron cookware are slow to
absorb heat, but generally cook evenly at low to
medium heat settings. Steel pans may cook unevenly
if not combined with other metals.
● For best cooking results pans should be flat on the
bottom. Match the size of the saucepan to the size of
the surface unit. The pan should not extend over the
edge of the trim ring more than l“.
6
Right
NOT OVER 1“
Wrong
OVER 1“
Page 7
Deep Fat Frying
● Do not overfill cookware with fat that may spill over when adding food.
Frosty foods bubble vigorously. Watch food frying at high temperatures.
Keep range and hood clean from grease.
Wok Cooking
● Use of these types of woks,
without the support rmg m
“~~~~~~:~1~
They are available at
your local retail store.
~
place, isdangerousbecause
the wok is unstable.
● With the ring in place, heat
will be trapped inside the
ring and may cause damage
to the porcelain cooktop.
HOME CANNING TIPS
Canning should be done on surface units only.
Pots
that extend beyond one inch of surface unit’s
drip pan are not recommended for most surface
cooking. However, when canning with water-bath or
pressure canner, larger-diameter pots may be used.
This is because boiling water temperatures (even
under pressure) are not harmful to cooktop surfaces
surrounding the surface unit.
Observe the Following Points in Canning
1. Be sure the canner fits over the center of the
surface unit. If your range or its location does not
allow
the canner to be centered on the surface unit,
use smaller-diameter pots for good canning results.
2. For best results, use canners with flat bottoms.
Canners with flanged or rippled bottoms (often
found in enamelware) don’t make good contact
with the surface unit and take a long time to boil
water.
Flat-bottomed canners are recommended.
HOWEVER, DO NOT USE LARGE DIAMETER
CANNERS OR OTHER LARGE DIAMETER
POTS FOR FRYING OR BOILING FOODS OTHER
THAN WATER. Most syrup or sauce
and all types of frying—cook at temperatures much
higher than boiling water. Such temperatures could
eventually harm cooktop surfaces surrounding
surface units.
3. When canning, use recipes and procedures from
reputable sources. Reliable recipes and procedures
are available from the manufacturer of your canner;
manufacturers of glass jars for canning,
Ball and Kerr; and the United States Department of
Agriculture Extension Service.
4. Remember that canning is a process that generates
large amounts of steam. To avoid burns from steam
or heat, be careful when canning.
NOTE: If your house has low voltage, canning
may take longer than expected, even though
directions have been carefully followed.
The process time will be shortened by:
(1)
using a pressure canner, and
(2) starting with HOT tap water for fastest heating
of large quantities of water.
mixtures—
such as
7
Page 8
AUTOMATIC TIMER AND CLOCK
(on some models)
To Set the Clock
To set the clock, push
the knob in and turn the
clock hands to the
correct time. (The
Minute Timer pointer will
move also. Let the knob
out, then turn the Minute
Timer pointer to OFF.)
4-
Questions and Answers
Q. Must the clock be set on correct time of
day when I wish to use the Automatic Timer
for baking?
A. Yes, if you wish to set the DELAY START or
STOP TIME dials (on some models) to turn on and
off at set times during timed functions.
Q. Can I use the Minute Timer during oven cooking?
A. The Minute Timer can be used during any cooking
function. The Automatic Timers (DELAY START
and STOP TIME dials) are used with TIMED
BAKE function only.
Minute Timer
The Minute Timer has been combined with the range
clock. Use it to time all your precise cooking
operations. You’ll recognize the Minute Timer as the
pointer which is different in color and shape than the
clock hands.
To Set the Minute Timer
To set the Minute Timer, turn the center knob,
without pushing in, until pointer reaches number of
minutes you wish to time. (Minutes are marked,
60, in the center ring on the clock.) At the end of the
set time, a buzzer sounds to tell you time is up.
Turn knob,
OFF and buzzer stops.
Q. Can I change the time of day on the clock
while I’m Time Baking in the oven?
A. The time of day on the clock should not be
changed during any program that uses the oven
timer. You must either stop those programs or wait
until they are finished before changing time.
without pushing in, until pointer reaches
up to
8
Page 9
Before Using Your Oven
1. Look at the controls. Be sure you understand how
to set them properly. Read over the directions for
the Automatic Timer and Clock so you understand
its use with the controls.
2. Check oven interior. Look at the shelves. Take a
practice run at removing and replacing them
properly, to give sure, sturdy support.
3. Read over information and tips that follow.
4. Keep this book handy so you can refer to it,
especially during the first weeks of using your
new range.
Oven Controls
The oven has two
control
OVEN TEMP and
OVEN SET. The
OVEN SET knob
has settings for
BAKE, TIMED
BAKE*, BROIL
and OFF.
OVEN TEMP maintains the temperature you set, from
WARM (
*TIMED BAKE on JMS1O
knobs—
150”F.)
to BROIL
OVEN SET
@@
(knob appearance may vary)
(550”F.).
only.
OVEN,TEMP
Oven Interior Shelves
The shelves are designed with stop-locks, so that
when placed correctly on the shelf supports, they
will stop before coming completely out from the
oven, and will not tilt when removing food from or
placing food on them.
TO REMOVE
the shelves from
the oven, pull the
shelf toward you,
tilt front end
upward and pull
the shelf out.
Oven Light
Use the switch on the panel to turn the light on
NOTE: The oven light will automatically turn on
~~~~eovendoorisopened.
TO REPLACE, place
the shelf on shelf
support with stop-locks
(curved extension of
shelf) facing up and
toward the rear of the
oven. Tilt up front and
push shelf toward the
back of the oven until
it goes past “stop” on the oven
front of the shelf and push it all the way back.
The oven has four shelf supports identified in the
illustration above as A (bottom), B, C and D (top).
Shelf positions for cooking are suggested in the
Baking, Roasting and
Bro[ling sections.
wall.
Then lower the
(continued next page)
9
Page 10
USING YOUR OVEN
Adjusting the Oven Thermostat
(continued)
Use the time given on a recipe when cooking the
first time. Oven thermostats, in time, may “drift”
from the factory setting and differences in timing
between an old and a new oven of 5 to 10 minutes are
not unusual. If you find that your foods consistently
brown too little or too much, you may make a simple
adjustment in the thermostat (OVEN TEMP) knob.
We do not recommend the use of inexpensive
thermometers, such as those found in the grocery
store, to check the temperature setting of your new
oven. These thermometers vary by 20-40 degrees.
Pull the knob off the shaft, look at the back of the
knob and note the current setting before making
any adjustment. The knob is factory set with the top
screw directly under the pointer.
Back of the OVEN TEMP knob
To adjust the thermostat:
1.
Pull off the knob.
2. Loosen both screws on back of the knob.
3. Hold both parts of the knob and turn so the lower
screw moves in the desired direction. You will hear
and feel notches as you turn the knob. Each notch
changes the temperature about 10° Fahrenheit.
The lower screw
moves toward
HOTTER
to
increase
the
temperature.
The lower screw
moves toward
COOLER
to
decrease
the
temperature.
Lower screw moves toward HOTTER or COOLER
How to Set Your Range for Baking
To avoid possible burns, place the shelves in the
correct position before you turn the oven on.
Step 1:
the OVEN SET
knob to BAKE
and the OVEN
TEMP knob to
the temperature
you desire.
Turn
OVEN TEMP
@
#
~
(2J
~<
OVEN SET
BAKE
:)
71(3W3
(TIMED BAKE on JMS 10 only)
4. Tighten the screws.
5. Return the knob to the range.
Re-check oven performance before making any
additional adjustments.
BAKING
Step 2: Turn the OVEN SET knob to OFF when
baking is finished.
10
Page 11
How to Time Bake
The automatic oven timer controls are designed to turn the oven on or off
automatically at specific times that you set. (Use TIMED BAKE on the
OVEN SET knob.)
How to Set Immediate Start and Automatic Stop
NOTE: Before beginning, make
OVE N SETOVEN TEMP
sure the hands of the range clock
show the correct time of day.
To start cooking immediately, and
turn off automatically, you must
turn the OVEN SET knob to
TIMED BAKE. Remember, foods
@
*
o
z
@
&
~0 8+-F
*
@
a
D
$
+0 %%
~o
;
%6
OIJ9 @
250
--.%
3
.@
continue cooking after controls are
Step
off because the oven retains heat,
for a long time, if the oven door is
not o~ened.
1
Step 1:
To set Stop Time, push in
knob on STOP TIME dial and turn
~ointer
~urn
to time vou want oven to
off; for
ex~mple 6:00.
The
DELAY START dial should be at
2: Turn OVEN SET knob to
TIMED BAKE. Turn OVEN
TEMP knob to oven temperature,
for example
250”F.
The oven will
start immediately and will stop at
the time you have set.
Both the Oven Cycling and the
Oven Set lights come on.
the same position as the time of
day on clock.
How to Set Delay Start and Automatic Stop
Delay Start and Automatic Stop is
setting the oven timer to turn the
oven on and off automatically at a
later time than the present time ofturn off, for example
day. You must use the TIMED
BAKE setting.and one-half hours of baking time.
STOP TIME OEIAY START
$2’:G (~;
6.>’
“’/,,,1,,,1’
Step 1:
“v/, ,;l,
PuSHTOTURN
To set start time, push in
Clock
,\I”
“u’
knob on DELAY START dial and
turn pointer to time you want oven
to turn on, for example
3:30.
Step 2:
To set Stop Time, push in
knob on STOP TIME dial and turn
pointer to time you want oven to
6:00.
This
means your recipe called for two
NOTE: Time on STOP TIME
dial must be later than time shown
on range clock and DELAY
START dial.
Step
3:
Turn OVEN SET knob to
TIMED BAKE. Turn OVEN TEMP
knob to desired temperature.
Place food in oven, close the door
and automatically the oven will be
turned on and off at the times you
have set. When cooking is
completed, turn OVEN SET to
OFF and remove food from oven.
NOTE:
Foods that spoil easily
such as milk, eggs, fish, stuffings,
poultry and pork should not be
allowed to sit out for more than
one hour before or after cooking.
Room temperature promotes the
growth of harmful bacteria. Be
sure that the oven light is off
because heat from the bulb will
speed harmful bacteria growth.
OVEN INDICATOR LIGHT(S) at
TIMED BAKE setting may work
differently than they do at BAKE
setting. Carefully recheck the steps
given above. If all operations are
done as explained, oven will
operate as it should.
NOTE: Foods that spoil easily
such as milk, eggs, fish, stuffings,
poultry and pork should not be
allowed to sit out for more than
one hour before or after cooking.
Room temperature promotes the
growth of harmful bacteria. Be
sure that the oven light is off
because heat from the bulb will
speed harmful bacteria growth.
11
Page 12
For best baking results, follow these suggestions:
Oven Shelves
BAKING
(continued)
Arrange the oven
shelf or shelves
in the desired
locations while
the oven is cool.
The correct shelf
position depends
on
the kind of
food and the
browning desired.
As a
general
rule.
place most foods in the middle of the oven, on either
the second or third shelf from the bottom. See the
chart for suggested shelf positions.
Preheating
Preheat the oven if the recipe calls for it. Preheat
means bringing the oven up to the specified
temperature before putting in the food. To preheat, set
the oven at the correct temperature—selecting a
higher temperature does not shorten preheat time.
Type of Food
Angel food cake
9
Biscuits or muffinsB or C
Cookies or cupcakes
Brownies,
Layer cakes
I Bundt or~ound cakes
Pies or pie shellsB or C
Frozen pies
Casseroles
RoastingA or B
Preheating is necessary for good results when baking
cakes, cookies, pastry and breads. For most casseroles
and roasts, preheating is not necessary. For ovens
without a preheat indicator light or tone, preheat 10
minutes. After the oven is preheated place the food
in the oven as quickly as possible to prevent heat
from escaping.
L
Shelf Position
A
I
B orC
B or C
B or C
I
A orB
A (on cookie sheet)
B or C
I
I
Baking Pans
Use the proper baking pan. The type of finish on the
pan determines the amount of browning that will occur.
● Dark, rough or dull pans absorb heat resulting in a
browner, crisper crust. Use this type for pies.
● Shiny, bright and smooth pans reflect heat, resulting
in a lighter, more delicate browning. Cakes and
sugar cookies require this type of pan.
● Glass baking dishes also absorb heat. When baking
in glass baking dishes, lower the temperature by
25”F.
and use the recommended cooking time in the
recipe. This is not necessary when baking pies or
casseroles.
12
Pan Placement
For even cooking and proper browning, there must be
enough room for air circulation in the oven. Baking
results will be better if baking pans are centered as
much as possible rather than being placed to the front
or to the back of the oven.
Pans should not touch each other or the walls of the
oven. Allow 1 to 1 M inch space between pans as well
as from the back of the oven, the door and the sides. If
you use two shelves stagger the pans so one is not
directly above the other.
Page 13
Baking Guides
When using prepared baking mixes, follow recipe or instructions for
best results.
Cookies
When baking cookies, flat cookie sheets (without
sides) produce better-looking cookies. Cookies baked
in a jelly roll pan (short sides all around) may have
darker edges and pale or light browning may occur.
Do not use a cookie sheet so large that it touches the
walls or the door of the oven.
For best results, use only one cookie sheet in the oven
at a time.
Pies
For best results, bake pies in dark, rough or dull pans
to produce a browner, crisper crust. Frozen pies in foil
pans should be placed on an aluminum cookie sheet
for baking since the shiny foil pan reflects heat away
from the pie crust; the cookie sheet helps retain it.
Aluminum Foil
Never entirely cover a shelf with a large cookie sheet
or aluminum foil. This will disturb the heat
circulation and result in poor baking. A smaller sheet
of foil may be used to catch a
on a lower rack several inches below the food.
spillover
by placing it
Cakes
When baking cakes, warped or bent pans will cause
uneven baking results and poorly shaped products.
A cake baked in a pan larger than the recipe
recommends will usually be crisper, thinner and drier
than it should be. If baked in a pan smaller than
recommends, it may be undercooked and batter may
overflow. Check the recipe to make sure the pan size
used is the one recommended.
Don’t Peek
Set the timer for the estimated cooking time and do
not open the door to look at your food. Most recipes
provide minimum and maximum baking times such
as “bake 30-40 minutes.”
DO NOT open the door to check until the minimum
time. Opening the oven door frequently during
cooking allows heat to escape and makes baking
times longer. Your baking results may also
be affected.
13
Page 14
ROASTING
Roasting is cooking by dry heat. Tender meat or
poultry can be roasted uncovered in your oven.
Roasting temperatures, which should be low and
steady, keep spattering to a minimum.
Roasting is really a baking procedure used for meats.
Therefore, oven controls are set to BAKE or TIMED
BAKE. (You may hear a slight clicking sound,
indicating the oven is working properly.)
Roasting is easy; just follow these steps:
Step 1: Position in oven on shelf in
A or B position.
No preheating is necessary.
Step 2: Check
weight of meat,
and place,
fat-
side-up, or
poultry
breast-
side-up, on
roasting rack in a
shallow pan. The
melting fat will
baste the meat.
Select a pan as close to the size of the meat as
possible. (Broiler pan with rack is a good pan for
this.) Line broiler pan with aluminum foil when using
pan for marinating, cooking with fruits, cooking
heavily cured meats, or for basting food during
cooking. Avoid spilling these materials inside the
oven door.
Step 3:
Turn
OVEN SET to
BAKE and OVEN
TEMP to
325”F.
Small poultry
may be cooked
at
375”F.
for
best browning.
OVEN TEMP
,50
300
$0
0
z
00$
@
+0&,8
(1
\
&
on JMS 10 only)
Step 4: Most meats continue to cook slightly while
standing, after being removed from the oven.
Standing time recommended for roasts is 10 to 20
minutes. This allows roasts to firm up and makes
them easier to carve. Internal temperature will rise
about 5° to 10”F.; to compensate for temperature rise,
if desired, remove roast from oven sooner (at 5° to
10”F. less than temperature in the guide).
NOTE: You may wish to use TIMED BAKE, as
described in the Baking section of this book, to turn
oven on and off automatically.
Remember that food will continue to cook in the hot
oven and therefore should be removed when the
desired internal temperature has been reached.
Frozen Roasts
● Frozen roasts of beef, pork, lamb, etc., can be started
without thawing, but allow 10 to 25 minutes per
pound additional time (10 minutes per pound for
roasts under 5 pounds, more time for larger roasts).
● Thaw most frozen poultry before roasting to ensure
even doneness. Some commercial frozen poultry can
be cooked successfully without thawing. Follow
directions given on package label.
Page 15
Questions and Answers
Q. Is it necessary to check for doneness with a
meat thermometer?
A. Checking the finished internal temperature at the
completion of cooking time is recommended.
Temperatures are shown in Roasting Guide. For
roasts over
8
lbs., check with thermometer at
half-
hour intervals after half the time has passed.
Q. Why is my roast crumbling when I try to
carve it?
A. Roasts are easier to slice if allowed to cool 10 to
20 minutes after removing from oven. Be sure to
cut across the grain of the meat.
ROASTING GUIDE
Oven
‘Me
Meat
Tender cuts; rib, high quality sirloin
tip, rump or top round*
Lamb leg or bone-in shoulder*
Veal shoulder, leg or loin*
Pork loin, rib or shoulder*
Ham, precooked
Poultry
Chicken or Duck
Chicken pieces
Turkey
Temperature
325°
325°
325°
325°
325°
325°
350°
325°
Q.
Do
I need to preheat my oven each time I cook a
roast or poultry?
A. It
is unnecessary to preheat your oven.
Q. When buying a roast, are there any special tips
hat would help me cook it more evenly?
A. Yes.
Buy a roast as even in thickness as possible,
or buy
rolIed
roasts.
Q. Can I seal the sides of my foil “tent” when
roasting a turkey?
A. Sealing the foil will steam the meat. Leaving
it unsealed allows the air to circulate and brown
the meat.
Approximate Roasting Time
Donenessin Minutes per Pound
Rare:
Medium:
Well
Done:
Rare:
Medium:
Well Done:
Well Done:
Well Done:
To Warm:17-20 minutes per pound (any weight)
boneless rolled roasts over 6 inches thick, add 5 to 10 minutes per pound to times given above.
*The U.S. Department of Agriculture says “Rare beef is popular, but you should know that cooking it to only
some food poisoning organisms may survive.” (Source: Safe Food Book. Your Kitchen Guide. USDA Rev. June 1985.)
140°F.
means
Page 16
BROILING
Broiling is cooking food by intense radiant heat from
the upper unit in the oven. Most fish and tender cuts
of meat can be broiled. Follow these steps to keep
spattering and smoking to a minimum.
Step 1: If meat has fat or gristle near edge, cut vertical
slashes through both about 2“ apart. If desired, fat may
be trimmed, leaving layer about 1/8” thick.
Step
2:
Place meat on broiler rack in broiler pan.
Always use rack so fat drips into broiler pan;
otherwise juices may become hot enough to catch fire.
Step
3:
Position shelf on recommended shelf position
as suggested in Broiling Guide. Most broiling is done
on C position, but if your range is connected to 208
Volts, you may wish to use a higher position.
Step
4:
Leave
door open to the
broil stop
r
position. The door
stays open by
itself, yet the
r
r
proper temperature
is
maintained in
the oven.
Step
5:
Turn
OVEN SET and
OVEN TEMP
knobs to BROIL.
Preheating units
is not necessary.
(See notes in
($
@
OVEN SET
BROIL
–
awl
~
:
$
OVEN TEMP
Broiling Guide.)
Step 6: Turn food only once during broiling. Time
foods for first side per Broiling Guide.
Turn food, then use times given for second side as a
guide to preferred doneness. (Where two thicknesses
and times are given together, use first times given for
thinnest food.)
Step 7: When
OVEN SET
OVEN TEMP
finished broiling,
OVEN SET
turn
and OVEN TEMP
knob to OFF. Serve
food immediately,
leaving the broiler
pan and rack outside
oven to cool during meal
for easiest cleaning.
Use of Aluminum Foil
You can use aluminum foil to line your broiler pan and broiler rack, However,
you must mold the foil tightly to the rack and cut slits in it just like the rack.
Without the slits, the foil will prevent fat and meat juices from draining to
the broiler pan. The juices could become hot enough to catch on fire. If you
do not cut the slits, you are frying, not broiling.
Questions & Answers
Q. When broiling, is it necessary to always use a
rack in the pan?
A. Yes.
Using
pan. As
the rack suspends the meat over the
tie
meat
cooks;
the juices fall into the pan,
thus keeping meat drier. Juices are protected by the
rack and stay cooler, thus preventing excessive
spatter and smoking.
Q. Should I salt the meat before broiling?
A. No. Salt draws out the
evaporate. Always
with tongs; piercing meat with a fork allows
to
escap~.
When
juices
salt”after
br~iling
and allows them to
cooking. Turn meat
poultry or fish,
juices
bru~h
each side often with butter.
Q. Why are my meats not turning out as brown as
they should?
A. In some areas, the
be low. In
minutes before placing broiler pan with food in
oven. Check to see if you are using the
recommended shelf position. Broil for longest
period of time indicated in the Broiling Guide.
Turn food only once during broiling.
~.
Do I need to grease my broiler rack to prevent
meat from sticking?
A. No. The broiler rack is designed to reflect broiler
heat, thus keeping the surface cool enough to
prevent meat from sticking to the surface.
However, spraying the broiler rack lightly with a
vegetable cooking spray before cooking will make
cleanup easier.
16
Power
these ca~es,
(voltage) to the oven mav
preheat
t~e’
broil unit for 10
Page 17
1. Always use broiler pan and rack that comes with
your oven. It is designed to minimize smoking and
spattering by trapping juices in the shielded lower
part of the pan.
2.
Oven door should be open to the broil stop
position. (see Broiling section)
3. For steaks and chops, slash fat evenly around
outside edges of meat. To slash, cut crosswise
through outer fat surface just to the edge of the
meat. Use tongs to turn meat over to prevent
piercing meat and losing juices.
4.
If desired, marinate meats or chicken before
broiling, or brush with barbecue sauce last 5 to 10
minutes only.
5.
When arranging food on pan, do not let fatty edges
hang over sides, which could soil oven with fat
dripping.
6. Broiler does not need to be preheated. However,
for very thin foods, or to increase browning,
preheat if desired.
7.
Frozen steaks can be broiled by positioning the
oven shelf at next lowest shelf position and
increasing cooking time given in this guide 1
X
times per side.
8.
If your range is connected to 208 Volts, rare steaks
may be
bro~led
by preheating the broiler and
positioning the oven shelf one position higher.
Food
Bacon
Ground Beef
Well Done
Beef Steaks
Rare
Medium
Well Done
Rare
Medium
Well Done
Chicken
Bakerv Products
Bread {Toast) or
Toaster Pastries
Endish Muffins
Lobster Tails
Fish
Ham Slices
Pork Chops
Well Done
Lamb Chops
Medium
Well Done
Medium
Well Done
Wieners
precooked sausages.
—
bratwurst
and similar
Quantity
Thickness
1/2
lb.
(about 8
andlor
thin slices)
1
lb. (4 patties)
1/2 to 3/4 inch
1
inch thick
(1 to
1X
inch thick
(2 to
1
whole
(2 to
split lengthwise
to 4 slices
2
1 pkg. (2)
2 (sDlit)
2-4
(6 to 8 oz. each)
l-lb. fillets 1/4 to
1/2
incb
I
inch thick
2 (1/2 inch thick)
2(1 inch thick)
about
2(1 inch thick)
about 10 to 12 oz.
2 ( I X inch thick)
about 1 lb.
l-lb. pkg.
IX
2X
2X
Ibs.)
Ibs.)
Ibs.),
thick
1
lb.
thick
(10)
c
c
c
c
c
A35
c
I
7--5
+
1
c
B
I
c
c
c
Second Side
Time, Minutes
4X
7
5
8
12
10
15
25
1
Z-2
10
13
10
12
14
6
11
7-8
14-16
20-25
10-15
1/2
Do not
turn over.
8
10
13
9
10
12
12-14
1-2
Comments
Arrange in
Space evenly.
Up to 8 patties take about same time.
Steaks less than 1 inch thick cook through
before browning. Pan frying is recommended.
Slash fat.
Reduce time about 5 to 10 minutes
per side for cut-up chicken. Brush
each side with melted butter. Broil
skin-side-down first.
Space evenly. Place English muffins
up and brush with butter, if desired.
Cut through back of shell. Spread open.
Brush with melted butter before and
after half of broiling time.
Handle and turn very carefully. Brush with
lemon butter before and during cooking if
desired. Preheat broiler to increase browning.
Increase time 5 to 10 minutes per side
for 1 M inch thick or home-cured.(precooked)
Slash fat.
Slash fat.
If desired,
lengthwise;’cut
single layer.
split
sausages in half
into 51 to 6-inch pieces.
cut-side-
17
Page 18
,,
,,
CARE AND CLEANING
Proper care and cleaning are important so your range will give you efficient
and satisfactory service. Follow these directions carefully in caring for your
range to assure safe and proper maintenance.
Lift-Up Cooktop
,,
Clean the area under the cooktop often. Built-up soil,
especially grease, may catch fire. To make cleaning
easier, the entire
cooktop may be lifted
up and supported in
the up position.
Glass Surfaces
To clean the outside glass finish,
use a glass cleaner. Rinse and
polish with a dry cloth. Do not
allow the water or cleaner to run
down inside openings in the glass
while cleaning.
E
‘~z
,
Kick Panel
To clean the front of the kick panel, wash with soap and
water. Rinse well.
Be sure all surface units are turned off before
raising the cooktop. Grasp the front sides of the
cooktop and lift. The heating elements
to be removed before lifting.
After cleaning under the cooktop with hot, mild soapy
water and a clean cloth, lower the cooktop. Be careful
not to pinch your fingers.
do not need
Metal Parts
Do not use steel wool,
abrasives, ammonia or
commercial oven cleaners.
To safely clean surfaces; wash, - .&
rinse and then dry with a
soft cloth.
Do not use cleansing powders or harsh abrasives that
may scratch the surface.
&
j~~‘:-~:>
.;>, -:: .:
.
Y.
Porcelain Enamel Cooktop
The porcelain enamel finish is sturdy but breakable if misused. This finish is
acid-resistant. However, any acid foods spilled (such as fruit juices, tomato or
vinegar) should not be permitted to remain on the finish.
If acids
wipe it up right away. When the surface has cooled, wash with soap and water
or cleansing powders. Rinse well.
For other spills such as fat smatterings, wash with soap and water or cleansing
powders after the surface has cooled. Rinse well. Polish with a dry cloth.
spill
on the cooktop while it is hot, use a dry paper towel or cloth to
18
Page 19
Surface Units and Drip Pans
To clean the surface units, turn the control to the highest
setting for a minute. The coils will burn off any soil.
CAUTION
“
Do not immerse the surface units in liquids of any kind.
● Do not clean the surface units in a dishwasher.
● Do not bend the surface unit plug terminals.
● Do not attempt to clean, adjust or in any way repair
the plug-in receptacle.
To remove the drip pans for cleaning, the surface units
must be removed first. Make sure the surface units are
completely cool before touching them.
Surfac
Unit
\
Drip Pan
Lift the surface unit about 1 inch above the drip pan
and pull it out.
Do not lift the surface unit more than 1 inch.
If you do, it may not lie flat on the drip pan when
you plug it back in.
Repeated lifting of the surface unit more
than 1 inch above the drip pan can permanently
damage the receptacle.
To
replace a surface unit:
● Replace the drip pan into the recess in the
cooktop.
with the receptacle.
● insert the terminals of the surface unit through
the opening in the drip pan and into the receptacle.
● Guide the surface unit into place so it rests evenly.
Drip Pans
Remove the surface units. Then lift out the drip pans.
The drip pans can be cleaned by hand. Place them in a
covered container (or a plastic bag) with 1/4 cup
ammonia to loosen the soil. Then scrub with a soap
filled scouring pad if necessary. Rinse with clean
water and polish with a clean soft cloth.
The drip pans may also be cleaned in the dishwasher.
Clean the area under the drip pans often.
Built-up soil, especially grease, may catch fire.
Do not cover drip pans with foil. Using foil so close
to the receptacle could cause shock, fire or damage to
the range.
CAUTION: Be sure all controls are turned to
OFF and surface units are cool before attempting
to remove them.
Make sure opening in the pan lines up
Control Panel and Knobs
Clean up any spills or spatters with a damp cloth.
Remove heavier soil with warm, soapy water.
Clean control panel with mild liquid dish detergent
and a soft cloth. Rub control panel lightly.
CAUTION: Do not use abrasives of any kind on the
control panel.
The control knobs may be removed for easier
cleaning. To remove knob, pull it straight off the stem.
Wash knobs in soap and water but do not soak.
-
----
‘f-’!
T@ji
—-----==
(continued next page)
19
—.
.—
—
Page 20
CARE AND CLEANING
Oven Door
The oven door is removable, but it
is heavy. You may need help
removing and replacing the door.
To
remove the door, open it a few
inches to the special stop position
that will hold the door open. Grasp
firmly
door straight up and off the hinges.
NOTE: Be careful not to place
hands between the hinge and the
oven door frame as the hinge could
snap back and pinch fingers.
To replace the
door, make sure
the hinges are
in the special
stop position.
Position the
slots in the
bottom of the ‘ ‘
door squarely
over the hinges
at the same
time. If hinges snap back
against the oven frame,
pull them back out.
on each side and lift the
T
/’
/
I‘L
:$
,/
/
/
F
(continued)
TO CLEAN THE DOOR:
Inside of door:
● Soap and water will normally
do the job. Heavy spattering or
spillovers may require cleaning
with a mild abrasive cleaner.
Soapy, wet metal pads may also
be used. Do not allow food spills
with a high sugar or acid content
(such as milk, tomatoes,
sauerkraut, fruit juices or pie
filling) to remain on
the
surface.
They may cause a dull spot even
after cleaning.
● Household ammonia may make
the cleaning job easier. Place
1/2 cup in a shallow glass or
pottery container in a cold oven
overnight. The ammonia fumes
will help loosen the burned-on
grease and food.
● If necessary, you may use
an oven cleaner. Follow
package directions.
Outside of door:
●
Use soap and water to thoroughly
clean the top, sides and front of
the oven. DO NOT let water run
down through openings in the top
of the door. Rinse well. You may
also use a glass cleaner to clean
the glass on the outside of the
door.
● Spillage of marinades, fruit
juices, tomato sauces and basting
materials containing acids may
cause discoloration and should be
wiped up immediately. When
surface is cool, clean and rinse.
● Do not use oven cleaners,
cleansing powders or harsh
abrasives on the outside of
the door.
Porcelain Oven Interior
With proper care, the porcelain enamel finish on the
inside of the oven—top, bottom, sides, back and inside
of the door—will stay new-looking for years.
Let range cool before cleaning. We recommend that
you wear rubber gloves when cleaning the range.
Soap and water will normally do the job. Heavy
spattering or spillovers may require cleaning with a
mild abrasive cleaner. Soapy, wet metal pads may also
be used. Do not allow food spills with a high sugar or
acid content (such as milk, tomatoes, sauerkraut, fruit
juices or pie filling) to remain on the surface. They
may cause
Household ammonia may make the cleaning job
easier. Place
container in a cold oven overnight. The ammonia
fumes will help loosen the burned-on grease and food.
NOTE: Do not clean the bake unit or broil unit. Any
soil will burn off when the unit is heated. The bake
unit can be lifted gently to clean the oven floor. If
spillover, residue, or ash accumulate around the bake
unit, gently wipe around the unit with warm water.
a
dull spot even after cleaning.
1/2
cup in a shallow glass or pottery
If necessary, you may use an oven cleaner.
Follow package directions.
Cautions about using spray-on oven cleaners:
●
Do
not
spray on the electrical controls and switches
because it could cause a short circuit and result in
sparking or fire.
● Do not allow a film from the cleaner to build up on
the temperature sensor—it could cause the oven to
heat improperly. (The sensor is located at the top of
the oven.) Carefully wipe the sensor clean after each
oven cleaning, being careful not to move the sensor
as a change in its position could affect how the oven
bakes.
●
Do
not
spray any oven cleaner on the oven door,
handles or any exterior surface of the oven, wood or
painted surfaces. The cleaner can damage these
surfaces.
20
Page 21
Oven Lamp Replacement
CAUTION: Before replacing your oven lamp bulb,
disconnect the electric power for your range at the
main fuse or circuit breaker panel or pull the plug.
Be sure to let the lamp cover and bulb cool
completely before removing or replacing them. When
in use, light bulbs
can become warm enough to break
if touched with a moist cloth or towel. When cleaning,
avoid touching warm lamps with cleaning cloths if the
lamp cover is removed.
The oven lamp (bulb) is covered with a glass
removable cover which is held in place with a wire.
Remove the oven door, if desired, to reach the
cover easily.
‘{
7
\
-
G“\~:,,)o
@Q
G
k’
-%
\
)
I
To remove:
●
Hold your hand under the cover so it doesn’t fall
when released. With fingers of the same hand, firmly
push back the wire until it clears the cover. Lift off
the cover.
DO NOT REMOVE ANY SCREWS.
●
Replace bulb with 40-watt home appliance bulb.
To replace cover:
●
Place it into the groove of the lamp receptacle. Pull
the wire forward to the center of cover until it snaps
in place. When in place, the wire holds the cover
firmly. Be certain the wire is in the depression in the
center of the cover.
●
Connect electric power to the range.
Broiler Pan and Rack
After broiling, remove the broiler pan from the oven.
Remove the rack from the pan. Carefully pour out the
grease in the pan into a proper container. Wash and
rinse the pan and rack in hot soapy water.
-
If food has burned on, sprinkle the rack while hot,
with detergent and cover with wet paper towels or a
dishcloth. That way, burned-on foods will soak loose
while the meal is being served.
Do not store a soiled broiler pan and rack in the oven.
Oven Shelves
Shelves can be cleaned by hand using soap and water or with an abrasive cleanser.
After cleaning, rinse the shelves with clean water and dry. To remove heavy,
burned-on soil, you may use scouring pads. After scrubbing, wash with soapy
water, rinse and dry. Shelves may also be cleaned in self-cleaning oven, but
will discolor and lose some luster. See the Self-Cleaning section.
21
Page 22
QUESTIONS?
USE THIS PROBLEM SOLVER
PROBLEM
OVEN WILL
NOT WORK
OVEN LIGHT
DOES NOT WORK
OVEN DOES NOT
COOK PROPERLY
FOOD DOES NOT
BROIL
PROPERLY
POSSIBLE CAUSE
● The circuit breaker in your house has been tripped, or a fuse has been blown.
● Oven controls not properly set.
● Light bulb is loose.
● Bulb is defective. Replace.
● Switch operating oven light is broken. Call for service.
● Aluminum foil being used improperly in oven.
“
Incorrect cookware being used.
●
Clock set incorrectly.
“
Controls set incorrectly. Review each cooking section.
● Shelf position is incorrect.
● OVEN SET knob not set at BROIL.
● OVEN TEMP knob not set at correct temperature.
● Door not left in broil stop position.
● Improper shelf position being used. Check the Broiling guide.
● Food is being cooked on hot pan.
s
Cookware is not suited for broiling.
● Aluminum foil used on the broiler pan rack has not been fitted properly and
slit as recommended.
FOOD DOES NOT
ROAST OR BAKE
PROPERLY
SURFACE UNITS
NOT FUNCTIONING
PROPERLY
OVEN TEMPERATURE
● OVEN SET knob not set at BAKE.
● OVEN TEMP knob not set at correct temperature.
● Shelf position is incorrect.
● Incorrect cookware or cookware of improper size is being used.
● A foil tent was not used when needed to slow down browning during roasting.
“
Surface units are not plugged in solidly.
● Drip pans are not set securely in the
● Surface unit controls are not properly set.
●
OVEN TEMP knob needs adjustment. See the Adjusting Oven Thermostat section.
TOO HOT OR TOO COLD
If you need more help.. call, toll free:
GE Answer
Center@
800.626.2000
consumer information service
cooktop.
22
Page 23
With the purchase of your new GE appliance, receive the assurance that ifyou ever need
information or assistance from GE, we’ll be there. All you have to do is call—toll-free!
In-Home Repair Service
8011GECARES-(80~43Z2737)
AGE consumer service professional will provide expert repair service, sched-
uled at. a time that’s convenient for you. Many
operated locations offer you service today or tomorrow, or at your convenience
(7’:00
a.m. to
7:00
p.m. weekdays,
trained technicians know your appliance inside and out-so most repairs can be
handled in just one visit.
9:00
a.m. to
GE Consumer Service
2:00
p.m. Saturdays). Our
company-
factory-
GEAnswer Cente~
801162ti2000
Whatever your question about any GE major appliance, GE Answer
information service is available to help. Your call–and your question— will be
answered promptly and courteously. And you can call any time. GE Answer
Center@
service is open 24 hours a day, 7 days a week.
kr
Customers With Special Needs...
Center@
80~62/12000
Upon request, GE will provide
Braille controls for a variety of GE
appliances, and a brochure tocall
assist in planning a barrier-free
kitchen for persons with limited
mobility. To obtain these items,
free of charge, call 800.626.2000.
Consumers with impaired hearing or speech who have
access to a TDD or a conventional teletypewriter may
800-TDD-GEAC (800-833-4322) to request informa-
tion or service.
Service Contracts
8086262224
You can have the secure feeling that GE Consumer Service will still be there
after your warranty expires. Purchase a GE contract while your warranty is
in
effect
and you ’11 receive a substantial discount. With a multiple-year contract,
you’re assured of future service
at
today’s prices.
still
Parts
andAccessories
80116262002
Individuals qualified to service their own appliancesUser maintenance instructions contained in this booklet
can have needed parts or accessories sent. directly tocover procedures intended to be performed by ’any user.
their home. The GE parts system provides access to overOther servicing generally should be referred to qualified
4’7,000 parts... and
fully warranted. VISA, Mastercard and Discover cards
are accepted.
all C7E
C~enuine Renewal Parts areservice personnel. Caution must be exercised, since
improper servicing may cause unsafe operation.
Page 24
YOUR GE ELECTRIC RANGE
WARRANTY
WHAT IS COVERED
WHAT IS NOT COVERED
Staple
sales slip or cancelled check
here. Proof of original purchase date
is needed to obtain service
II
FULL ONE-YEAR WARRANTY
For one year from date of original
purchase, we will provide, free of
charge, parts and service labor in
your home to repair or replace
of
the
any parf
because of a manufacturing defect.
● Service trips to your home to
teach you how to use the product.
Read your Use and Care material.
If you then have any questions
about operating the product,
please contact your dealer or our
Consumer Affairs office at the
address below, or call, toll free:
GE Answer Center”
800.626.2000
consumer information service
● Improper installation.
If you have an installation problem,
contact your dealer or installer.
You are responsible for providing
adequate electrical, gas, exhausting
and other connecting facilities as
range that fails
under warranty.
This warranty is extended to
the original purchaser and any
succeeding owner for products
purchased for ordinary home use
48 mainland states, Hawaii
in the
and Washington,
warranty is the same except that it
is LIMITED because you must pay
to ship the product to the service
shop or for the service technician’s
travel costs to your home.
All warranty service will be
provided by our Factory Service
Centers or by our authorized
Customer
normal working hours.
Should your appliance need
service, during the warranty period
or beyond, call 800-GE-CARES
(800-432-2737).
described in the Installation
Instructions provided with the
product.
● Replacement of house fuses or
resetting of circuit breakers.
. Failure of the product if it is used
for other than its intended purpose
or used commercially.
● Damage to product caused
by accident, fire, floods or acts
of God.
WARRANTOR IS
FOR CONSEQUENTIAL DAMAGES.
Care” servicers during
D.C.
In Alaska the
AKXRESPONSIBLE
II
I
!
Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion
may not apply to you. This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.
To know what your legal rights are in your state, consult your local or state consumer affairs office or your state’s Attorney General.
If further help is needed concerning this warranty, write:
Manager—Consumer Affairs, GE Appliances, Louisville, KY 40225
EisEiH
4-93 CG
Warrantor: General Electric Company
JMS08GF
JMSI
Printed in LaFayette,
OG~
\
Loading...
+ hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.