GE JKP86BF1BB, JKP86BF2BB, JKP86BF3BB, JKP86BF4BB, JKP86BF5BB Installation Guide

...
Installation
27" Built-In Wall Oven
with Microwave
Instructions
If you have questions, call 1.800.GE.CARES or visit our website at:
www.GEAppliances.com
JKP86
Before You Begin
IMPORTANT-save these
instructions for local inspector's use.
IMPORTANT-observe a,
governing codes and ordinances.
Note to Installer--Be sure to leave these instructions with the consumer.
Note to ConsumermKeep these instructions for future reference,
Parts Included
Screws For Installation Metal Bottom Trim
Proper installation is the responsibility
of the installer and product failure due to improper installation is NOT covered under warranty.
NOTE--This appliance must be properly grounded.
ATTENTION INSTALLER
All electric wall ovens must be hard wired (direct wired) into an approved junction
box. A plug and receptacle is NOT permitted on these products.
Materials Needed
__ @ Wireaunts
Strain Relief Clamp Junction for 1/2" conduit Box %-_'_-,,
Tools Needed
1/8" Drill Bit and Electric or Hand Drill
229c4053P507-3
31-10526-3 o6-o3JR
36" of String
Phillips
Screwdriver
Installation Instructions
IMPORTANT SAFETY INSTRUCTIONS
For Your Safety
Be sure your oven is installed properly by
a qualified installer or service technician.
Be sure the oven is securely installed in a cabinet that is firmly attached to the house structure. Weight on the oven door could cause the oven to tip and result in injury. Never allow anyone to climb, sit, stand or hang on the oven door.
Make sure the cabinets and wall coverings around the oven can withstand the
temperatures (up to 200°F) generated by the oven.
WARNING: The electrical
power to the oven supply line must be shut off while line
connections are being made. Failure
to do so could result in serious injury
or death.
Electrical Requirements
This appliance must be supplied with the proper voltage and frequency, and connected to an individual, properly grounded branch circuit, protected by a circuit breaker or fuse having amperage as noted on rating plate. (Rating plate is located on the inside wall of the microwave oven.)
We recommend you have the electrical wiring and hookup of your oven connected by a qualified electrician. After installation, have the electrician show you where your main oven
disconnect is located. Check with your local utilities for electrical
codes which apply in your area. Failure to wire your oven according to governing codes could
result in a hazardous condition. If there are no local codes, your oven must be wired and fused
to meet the requirements of the National Electrical Code, ANSI/NFPA No. 70-Latest
Edition. You can get a copy by writing:
National Fire Protection Association Batterymarch Park
Quincy, MA 02269
Effective January 1,1996, the National Electrical Code requires that new, but not existing, construction utilize a four-conductor connection to an electric oven. When installing
an electric oven in new construction, a mobile home, recreational vehicle or an area where
local codes prohibit grounding through the neutral conductor, follow the instructions in the section on NEW CONSTRUCTION AND
FOUR-CONDUCTOR BRANCH CIRCUIT CONNECTION.
You must use a three-wire, single-phase A.C. 208Y/120 Volt or 240/120 Volt, 60 hertz
electrical system. If you connect to aluminum wiring, properly installed connectors approved for use with aluminum wiring must be used.
2
Installation Instructions
Pre-lnstallation Checklist
Remove packaging materials. Check inside microwave, behind hinges and
under false bottom. Remove labels on
the outside of the door, plastic on trims and panel and all tape around oven.
Oven Racks
Broiler Pan and Grid
Pack
Literature
Door removal is not a requirement for installation of the product, but is an
added convenience. To remove the door:
Open the oven door as far as it will go.
Push both hinge Hinge locks down toward _!_i__'_l_, Position
the door frame, Hinge"_ to the unlocked s_ot _,d
position. This may require a flat blade
screwdriver. Arm
DO NOT LIFT THE DOOR
BY THE HANDLE!
Place hands on both sides of the door, and close the oven door to the removal position.
This is half way between the
broil stop and fully closed.
_= Unlocked
Hinge
Open oven door and remove literature pack, broiler pan and grid, and oven racks. Open microwave door and remove shelves and turntable package.
Remove Installation Instructions
from literature pack and read them carefully before you begin.
Be sure to place all literature, Owner's Manual, Installations, etc.
in a safe place for future reference.
Lift door up and
out until the
hinge arms
clear the slots.
Hinge Clears Slot
NOTE: The oven door is very heavy. Be sure you have a firm grip before lifting
the oven door off the hinges. Use caution once the door is removed. Do not lay the
door on its handle. This could cause dents or scratches.
3
(Continued on following page)
Installation Instructions
I_ Pre-lnstallation Checklist cont.
[_ lace the oven on a table or platform
even with the cutout opening. (Platform must support 255 Ibs.)
Remove the bottom trim from the top of the oven. It will be installed at the
end of the installation process. The trim is wrapped separately and taped to the top of the unit.
4
Loading...
+ 8 hidden pages