GE JKP85BD1BB, JKP85WD1WW Installation Guide

Installation

27" Built In Wall Oven/with

Microwave

Instructions

JKP85

"If you have questions, call 800-GE-CARES orvisit our website at:

www. GEAppliances.com"

Before you begin

Read these instructions carefully and completely

• IMPORTANT-Save these instructions for

local inspector's use.

• IMPORTANT-Observe all governing

codes and ordinances.

• Note to Installer- Be sure to leave these

instructions with the consumer.

• OWNER- Keep these instructions for future

reference.

• ATTENTION INSTALLER!!
All electric wall ovens must be hard wired

(direct wired) into an approved junction
box. A "plug and receptacle" is NOT
permitted on these products

• NOTE- This appliance must be properly
grounded.

Parts Included

f

Bottom Trim

8 flat head screws side trim
3 Pan head screws bottom trim

Tools You Will Need

Materials Needed

_¢_ WireNu_ts

Strain Relief
Clamp

Junction

Box

36" of String

1/8" Drill Bit & Phillips
Electric or Screwdriver

Hand Drill

Pub. No. 31-10480

229c4053P460 1

Installation Instructions

IMPORTANT SAFETY INSTRUCTIONS

For Your Safety

• Be sure your oven is installed properly by

a qualified installer or service technician.

• Be sure the oven is securely installed in a
cabinet that is firmly attached to the house
structure. Weight on the oven door could
cause the oven to tip and result in injury.
Never allow anyone to climb, sit, stand or
hang on the oven door.

• Make sure the cabinets and wall cover-
ings around the oven can withstand the

temperatures (up to 200°F.) generated by
the oven.

_ CAUTION: The electrical power

to the oven supply line must be
shut off while line connections

are being made. Failure to do so

could result in serious injury or
death.

Electrical
Requirements

This appliance must be supplied with the
proper voltage and frequency, and connected
to an individual properly grounded branch
circuit, protected by a circuit breaker or fuse

having amperage as noted on rating plate.

(Rating Plate is located on oven side trim.)
We recommend you have the electrical wiring

and hookup of your oven connected by a
qualified electrician. After installation, have the
electrician show you where your main oven

disconnect is located.
Check with your local utilities for electrical

codes which apply in your area. Failure to wire
your oven according to governing codes could

result in a hazardous condition. If there are no
local codes, your range must be wired and

fused to meet the requirements of the National

Electrical Code, ANSI/NFPA No. 70-Latest
Edition. You can get a copy by writing:

National Fire Protection Association

Battery March Park

Quincy, MA 02269

Effective January 1, 1996, the National

Electrical Code requires that new, but not
existing, construction utilize a 4 conductor
connection to an electric range. When

installing an electric range in new construction,
follow the instructions in the section on NEW
CONSTRUCTION AND FOUR CONDUCTOR

BRANCH CIRCUIT CONNECTION.
You must use a three-wire, single-phase A.C.

208Y/120 Volt or 240/120 Volt, 60 hertz
electrical system. If you connect to aluminum

wiring, properly installed connectors approved
for use with aluminum wiring must be used.

2

Installation Instructions

Pre-Installation Checklist

Remove packaging materials.
Check behind hinges, and under

false bottom. Remove labels on the
outside of the door, plastic on trims

and panel, and all tape around oven.

Open oven door and remove literature
pack, broiler pan and grid, and oven

racks.
Remove Installation Instructions from

literature pack and read them carefully
before you begin.

Be sure to place all literature, Use and
Care, Installations, etc. in a safe place

for future reference.

Door Removal is not a requirement for

installation of the product, but is an added

convenience.

Open the oven door as far as it will go.

Push both hinge
locks down toward

the door frame, to
the unlocked

position. This may

require a flat blade

screwdriver.

Place hands on

both sides of the
door, close the oven

door to the removal
position this is half

way between the
broil stop and fully

closed.

_. Unlocked

Hinge

Arm

Hinge

Hinge

/ Clears

Slot

3 (Continued on following page)

Installation Instructions

1_ Place the oven on a table or platform Iq_"

even with the cutout opening.
(Platform must support 275 Ibs.)

Remove the bottom trim from the

top of the oven. It will be installed at
the end of installation. The trim is

wrapped separately and taped to the
top of the unit.

Bottom Trim

4