GE JKP30SMSS, JKP35WMWW, JKP35BMBB, JKP35SMSS, JKP55BMBB Installation Instructions Manual

...

Installation

Built-In Wall Oven

27” (68.6 cm) models

JKS10, JKP30, JKP35, JKP55, JKP70, JKP75, PK916, PK956, ZEK938, ZEK958

Instructions

30” (76.2 cm) models

JTP30, JTP35, JTP55, JTP70, JTP75, PT916, PT920, PT956, PT960, ZET938, ZET958

If you have questions, call 1.800.GE.CARES or visit our website at: ge.com

Before You Begin

Read these instructions carefully and completely.

• IMPORTANT—Save these

instructions for local inspector’s use.

• IMPORTANT—Observe all

governing codes and ordinances.

• Note to Installer—Be sure to leave these instructions with the consumer.

• Note to Consumer—Keep these instructions for future reference.

• Proper installation is the responsibility of the installer and product failure due to improper installation is NOT covered under warranty.

• NOTE—This appliance must be properly grounded.

• ATTENTION INSTALLER

All electric wall ovens must be hard wired (direct wired) into an approved junction box. A plug and receptacle is NOT permitted on these products.

Parts Included

(Appearance will vary)

Screws For Installation (8-18 x .750 flat head Phillips wood screws)

Optional 27″ (68.6 cm) Metal Bottom Trim Assembly (on some models or can be purchased separately)

27″ (68.6 cm) Metal Bottom Trim

30″ (76.2 cm) Metal Bottom Trim Assembly

Materials Needed

Wire Nuts

Strain Relief Clamp for 1/2” conduit

Junction Box

36” (91 cm) of String

Tools Needed

1/8” (3 mm) Drill Bit and Electric or Hand Drill

Phillips Screwdriver

31-10647 02-07 JR

Installation Instructions

IMPORTANT SAFETY INSTRUCTIONS

For Your Safety

• Be sure your oven is installed properly by a qualified installer or service technician.

• Be sure the oven is securely installed in a cabinet that is firmly attached to the house structure. Weight on the oven door could cause the oven to tip and result in injury. Never allow anyone to climb, sit, stand or hang on the oven door.

• Make sure the cabinets and wall coverings around the oven can withstand the temperatures (up to 200°F [93.3°C]) generated by the oven.

WARNING:

power to the oven supply line

must be shut off while line connections are being made. Failure to do so could result in serious injury or death.

The electrical

Electrical Requirements

This appliance must be supplied with the proper voltage and frequency, and connected to an individual, properly grounded branch circuit, protected by a circuit breaker or fuse. See the rating plate located on the oven frame to determine the rating of the product. Use the chart below to determine the minimum recommended dedicated circuit protection.

Recommended

KW Rating KW Rating Circuit Size

240V 208V (Dedicated)

≤4.8 KW ≤4.1 KW 20 Amp

4.9 KW–7.2 KW 4.3 KW–6.2 KW 30 Amp

7.3 KW–9.6 KW 6.3 KW–8.3 KW 40 Amp

9.7 KW–12.0 KW 8.4 KW–10.4 KW 50 Amp

Electrical Requirements cont.

Rating plate is located on oven side trim, side front frame or lower front frame.

Rating Plate Location

We recommend you have the electrical wiring and hookup of your oven connected by a qualified electrician. After installation, have the electrician show you where your main oven disconnect is located.

Check with your local utilities for electrical codes which apply in your area. Failure to wire your oven according to governing codes could result in a hazardous condition. If there are no local codes, your oven must be wired and fused to meet the requirements of the National Electrical Code, ANSI/NFPA No. 70–Latest Edition. You can get a copy by writing:

National Fire Protection Association Batterymarch Park Quincy, MA 02269

Effective January 1, 1996, the National Electrical Code requires that new, but not existing, construction utilize a four-conductor connection to an electric oven. When installing an electric oven in new construction, a mobile home, recreational vehicle or an area where local codes prohibit grounding through the neutral conductor, follow the instructions in the section on NEW CONSTRUCTION AND FOUR-CONDUCTOR BRANCH CIRCUIT CONNECTION.

You must use a three-wire, single-phase A.C. 208Y/120 Volt or 240/120 Volt, 60 hertz electrical system. If you connect to aluminum wiring, properly installed connectors approved for use with aluminum wiring must be used.

Installation Instructions

Hinge

Unlocked

Position

Hinge

Slot

Hinge

Arm

Pre-Installation Checklist

ALL INSTALLATION INFORMATION ON THE FOLLOWING PAGES IS TO BE USED FOR SINGLE AND DOUBLE OVEN INSTALLATION!

Door removal is not a requirement for installation of the product, but is an added convenience. To remove the door:

Open the oven door as far as it will go.

Remove packaging materials. Check behind hinges and under false bottom. Remove labels on the outside of the door, plastic on trims and panel, all tape around the oven, and any shipping screws securing the oven to the base pad.

Oven Racks

EASY INSTALLATION OF YOUR NEW

Before you begin-Read these instructions completely and carefully.

30" WALL OVEN

IMPORTANT- Save these instructions for local inspector’s use.

30" WALL OVEN

IMPORTANT- OBSERVE ALL GOVERNING CODES AND ORDIANCES.

IMPORTANT- OBSERVE ALL GOVERNING CODES AND ORDIANCES. Note to Installer- Be sure to leave these instructions with the consumer.

Note to Installer- Be sure to leave these instructions with the consumer.

Note to Installer- Be sure to leave these instructions with the consumer. OWNER- Keep these instructions for future reference.

OWNER- Keep these instructions for future reference.

Before you begin-Read these instructions completely and carefully.

Note- This appliance must be properly grounded (if applicable).

IMPORTANT- Save these instructions for local inspector’s use.

IMPORTANT- Save these instructions for local inspector’s use. IMPORTANT- OBSERVE ALL GOVERNING CODES AND ORDIANCES.

IMPORTANT- OBSERVE ALL GOVERNING CODES AND ORDIANCES.

IMPORTANT- OBSERVE ALL GOVERNING CODES AND ORDIANCES. Note to Installer- Be sure to leave these instructions with the consumer.

Note to Installer- Be sure to leave these instructions with the consumer.

Note to Installer- Be sure to leave these instructions with the consumer. OWNER- Keep these instructions for future reference.

OWNER- Keep these instructions for future reference.

FOR YOUR SAFETY

Note- This appliance must be properly grounded (if applicable).

Before you begin-Read these

Before you begin-Read these instructions completely and

instructions completely and

carefully.

FOR YOUR SAFETY

ELECTRICAL REQUIREMENTS

FOR YOUR SAFETY

ELECTRICAL REQUIREMENTS

IMPORTANT- Save these

ELECTRICAL REQUIREMENTS

instructions for local inspector’s use.

Before you begin-Read these

IMPORTANT- OBSERVE ALL

Before you begin-Read these

instructions completely and

GOVERNING CODES AND ORDIANCES.

instructions completely and

carefully.

Note to Installer- Be sure to leave

carefully.

IMPORTANT- Save these

these instructions with the consumer.

IMPORTANT- Save these

instructions for local inspector’s use.

OWNER- Keep these instructions

instructions for local inspector’s use.

IMPORTANT- OBSERVE ALL

for future reference.

IMPORTANT- OBSERVE ALL

Note- This appliance must be

GOVERNING CODES AND ORDIANCES.

GOVERNING CODES AND ORDIANCES. properly grounded (if applicable).

properly grounded (if applicable).

Note to Installer- Be sure to leave

these instructions with the consumer.

Before you begin-Read these

these instructions with the consumer.

instructions completely and

OWNER- Keep these instructions

carefully.

for future reference.

for future reference. IMPORTANT- Save these

IMPORTANT- Save these

Note- This appliance must be

Note- This appliance must be instructions for local inspector’s use.

instructions for local inspector’s use.

properly grounded (if applicable).

properly grounded (if applicable). IMPORTANT- OBSERVE ALL

IMPORTANT- OBSERVE ALL

Before you begin-Read these

GOVERNING CODES AND ORDIANCES.

instructions completely and

Note to Installer- Be sure to leave

carefully.

these instructions with the consumer.

IMPORTANT- Save these

instructions for local inspector’s use.

instructions for local inspector’s use. IMPORTANT- OBSERVE ALL

IMPORTANT- OBSERVE ALL

GOVERNING CODES AND ORDIANCES.

GOVERNING CODES AND ORDIANCES. Note to Installer- Be sure to leave

Note to Installer- Be sure to leave

Note to Installer- Be sure to leave these instructions with the consumer.

these instructions with the consumer.

OWNER- Keep these instructions

OWNER- Keep these instructions for future reference.

for future reference.

for future reference. Note- This appliance must be

Note- This appliance must be

Note- This appliance must be properly grounded (if applicable).

properly grounded (if applicable).

instructions for local inspector’s use.

instructions for local inspector’s use. IMPORTANT- OBSERVE ALL

IMPORTANT- OBSERVE ALL

IMPORTANT- OBSERVE ALL GOVERNING CODES AND ORDIANCES.

GOVERNING CODES AND ORDIANCES.

GOVERNING CODES AND ORDIANCES. Note to Installer- Be sure to leave

Note to Installer- Be sure to leave

Note to Installer- Be sure to leave these instructions with the consumer.

these instructions with the consumer.

these instructions with the consumer. OWNER- Keep these instructions

OWNER- Keep these instructions

OWNER- Keep these instructions for future reference.

for future reference.

for future reference. Note- This appliance must be

Note- This appliance must be

Note- This appliance must be properly grounded (if applicable).

properly grounded (if applicable).

Literature Pack

OWNER- Keep these instructions

OWNER- Keep these instructions for future reference.

for future reference.

Note- This appliance must be

Note- This appliance must be properly grounded (if applicable).

properly grounded (if applicable).

instructions for local inspector’s use.

instructions for local inspector’s use. IMPORTANT- OBSERVE ALL

IMPORTANT- OBSERVE ALL

IMPORTANT- OBSERVE ALL GOVERNING CODES AND ORDIANCES.

GOVERNING CODES AND ORDIANCES.

GOVERNING CODES AND ORDIANCES. Note to Installer- Be sure to leave

Note to Installer- Be sure to leave

Note to Installer- Be sure to leave these instructions with the consumer.

these instructions with the consumer.

these instructions with the consumer. OWNER- Keep these instructions

OWNER- Keep these instructions

OWNER- Keep these instructions for future reference.

for future reference.

for future reference. Note- This appliance must be

Note- This appliance must be

Note- This appliance must be properly grounded (if applicable).

properly grounded (if applicable).

Open oven door and remove literature pack and oven racks.

Remove Installation Instructions from literature pack and read them carefully before you begin.

Be sure to place all literature, Owner’s Manual, Installations, etc. in a safe place for future reference.

Push both hinge locks down toward the door frame, to the unlocked

Hinge Slot

Hinge Unlocked Position

position. This may require a flat blade screwdriver.

Hinge Arm

DO NOT LIFT THE DOOR

BY THE HANDLE!

Place hands on both sides of the door, and close the oven door to the removal position, which is most of the way closed.

Lift door up and out until the hinge arms clear the slots.

Hinge Clears Slot

NOTE: The oven door is very heavy. Be sure you have a firm grip before lifting the oven door off the hinges. Use caution once the door is removed. Do not lay the door on its handle. This could cause dents or scratches.

Place the oven on a table or platform even with the cutout opening. (Platform must support 150 lbs. [68 Kg] single, 275 lbs. [124 Kg] double.)

Remove the bottom trim from the top of the oven. It will be installed at the end of the installation process. The trim is wrapped separately and taped to the top of the unit.

Installation Instructions

Cutout for 27″ (68.6 cm) Single Built-In Ovens only

For JKS10, JKP30, JKP70, PK916, ZEK938 models only.

Allow 1” (2.5 cm) for overlap of oven over side edges of cutout

2” x 4” (5 cm x 10 cm) or equivalent runners level with bottom of cutout

20” (50.8 cm)

Allow a minimum of 20” (50.8 cm) for clearance to adjacent corners, drawers, walls, etc. when door is open

5” (12.7 cm)

Max. from the

Cabinet

27” (68.6 cm)

Cutout Width 25” (63.5 cm)

25 1/4” (64.1 cm)

Allow 1 3/8” (3.5 cm) minimum for overlap of oven top and bottom of cutout

left or right

Width

Min. Max.

side

Cutout Height 27 5/8” (70.2 cm) Min. 28 1/8” (71.4 cm) Max.

Recommended cutout location from floor 32 1/2” (82.6 cm)

Junction Box Location

22” (55.9 cm) Min. above base rail

Alternate Junction Box Location – access from adjacent cabinet may be required

Cabinet Width 27” (68.6 cm) Recommended

Cutout Location from Floor 32 1/2” (82.6 cm)

Cutout Depth 23 1/2”

(59.7 cm) Min.

Cutout Width 25” (63.5 cm) Min.

25 1/4” (64.1 cm) Max.

Cutout Height 27 5/8” (70.2 cm) Min.

28 1/8” (71.4 cm) Max.

NOTE: If the cabinet does not have a front frame and the sides are less than 3/4” (1.9 cm) thick, shim both sides equally to establish the cutout width.

If the cabinet does not have a solid bottom, two braces or runners must be installed level with the bottom of the cutout to support the weight of the oven. For single ovens, the runners and braces must support 150 lbs (68 Kg).

NOTE: If marks, blemishes or the cutout opening are visible above the installed oven, it may be necessary to add wood shims under the runners and front trim until the marks or opening are covered.

2" x 4" or

2” x 4” (5 cm x 10 cm) or

equivalent runners level

Equivalent

with bottom of cutout

Runners

24”

24"

(61 cm)

18"

18” (45.7 cm) 27” (68.6 cm)

27"

These ovens are not approved for stackable installations.

Cutout for 27″ Ovens only

For JKP35, JKP55, JKP75, PK956, ZEK958 models only.

Allow 1” (2.5 cm) for overlap of oven over side edges of cutout

2” x 4” (5 cm x 10 cm) or equivalent runners

20” (50.8 cm)

Allow a minimum of 20” (50.8 cm) for clearance to adjacent corners, drawers, walls, etc. when door is open

Installation Instructions

(12.7 cm)

Max. from

the left or

Cabinet

Width

27”

(68.6 cm)

Cutout

Width

25” (63.5 cm) Min.

25 1/4”

(64.1 cm) Max.

Allow 1 3/8” (3.5 cm) for overlap of oven top and bottom of cutout

right

5”

side

Cutout Height 49 11/16” (126.2 cm) Min. 50 1/8” (127.3 cm) Max.

Recommended cutout location from floor 13 1/4” (33.7 cm)

(68.6 cm)

Junction Box Location

44”

(111.8 cm)

Min.

Above

base rail

Double Built-In

Cabinet Width 27” (68.6 cm) Recommended

Cutout Location from Floor 13 1/4” (33.7 cm)

Cutout Depth 23 5/8” (60 cm) Min. Cutout Width 25” (63.5 cm) Min.

25 1/4” (64.1 cm) Max.

Cutout Height 49 11/16” (126.2 cm) Min.

50 1/8” (127.3 cm) Max.

NOTE: If the cabinet does not have a front frame and the sides are less than 3/4” (1.9 cm) thick, shim both sides equally to establish the cutout width.

If the cabinet does not have a solid bottom, two braces or runners must be installed to support the weight of the oven. For double ovens, the runners and braces must support 300 lbs (135 Kg).

NOTE: If marks, blemishes or the cutout opening are visible above the installed oven, it may be necessary to add wood shims under the runners and front trim until the marks or opening are covered.

Suitable Bracing to Support Runners

18"

18”

OVER CENTERLINE

(45.7 cm)

OF CABINET

Over Centerline

of Cabinet

2” x 4”

2" x 4" or EQUIVALENT

(5 cm x 10 cm)

RUNNERS

or equivalent runners level with bottom of cutout

Installation Instructions

Cutout for 27″ (68.6 cm) Single Built-In Ovens only Under Counter

For JKS10, JKP30, JKP70, PK916, ZEK938 models only.

Gas or electric cooktops may be installed over this oven. See cooktop installation instructions for cutout size. See label on top of oven for approved cooktop models.

240V / 208V Junction Box Location

25” (63.5 cm)

5”

(12.7 cm)

Max. from the

left or right

side

Gas and electrical connections for gas cooktop must be located in an adjacent accessible location to the right.

Top and/or side fillers may be necessary if unit is positioned between existing cabinets. Be sure they are attached securely, since they will anchor the oven in the cabinet.

3/4” (1.9 cm)

Support Platform

Required

25” (63.5 cm) Min. 25 1/4” (64.1cm) Max.

27 5/8” (70.2 cm) Min. 28 1/8” (71.4 cm) Max.

Allow 1 3/8” (3.5 cm) unit overlap top and bottom of oven, 1” (2.5 cm) unit overlap side edges

Must match toekick height

22” (55.9 cm) Min. Above Support Platform

24” (61cm)

4” (10.2 cm) Typical Toekick

36” (91.4 cm) Typical Countertop Height

MUST SUPPORT 150 LBS. (68 Kg)

NOTE: This oven is not approved to be installed under a solid disk, induction or downdraft modular cooktop.

Cabinetry

Cutout for 27″ (68.6 cm) Single or Double Built-In Ovens only – Over a Warming Drawer

For JKS10, JKP30, JKP35, JKP55, JKP70, JKP75, PK916, PK956, ZEK938, ZEK958 models only.

Single 27″ (68.6 cm) Oven Over a Warming Drawer

Per Warming Drawer Requirement

Anti-Tip Block Against Rear Wall Per Warming Drawer Requirement

3” (7.6 cm) Min.

1” (2.5 cm) Min. Above Toekick or Adjust to Oven Installation Height

NOTE: Install the

oven only with specific models listed on the label located on top of the oven.

Double 27″ (68.6 cm)

Oven Over a Warming Drawer

Per Warming Drawer Requirement

1” (2.5 cm) Min. Above Toekick

Anti-Tip Block Against Rear Wall Per Warming Drawer Requirement

3” (7.6 cm) Min.

NOTE: Additional clearances between cutouts

may be required. Check to be sure the oven supports above the Warming Drawer location do not obstruct the required interior depth and height.

• When installing a Warming Drawer below a single or double oven, a separate 120V, 60 Hz, properly grounded receptacle must be installed. Refer to installation instructions packed with the Warming Drawer for specific installation requirements.

Cabinetry

Cutout for 27″ (68.6 cm) Single Ovens only – Below an Advantium or Between an Advantium and a W arming Drawer

For JKS10, JKP30, JKP70, PK916, ZEK938 models only.

Single 27″ (68.6 cm) Oven Below an Advantium

Per Advantium Requirement

NOTE: The middle rail separating the two

openings may need to be larger than the 3” (7.6 cm) minimum shown. Always refer to the individual installation instructions packed with each product for specific requirements.

Combined Advantium and Wall Oven Installation:

When installed in combination with a single wall oven, use separate electrical junction boxes.

• Refer to the Advantium oven installation instructions for electrical requirements of that product.

• These connections must be made by a qualified electrician. All electrical connections must meet National Electrical Code or prevailing local codes.

3” (7.6 cm) Min.

Note: Install the

oven only with specific models listed on the label located on top of the oven.

Single 27″ (68.6 cm) Oven Between an Advantium and a Warming Drawer

Per Advantium Requirement

Per Warming Drawer Requirement

NOTE: Additional clearances may be

required. Check to be sure the oven supports above the Warming Drawer do not obstruct the required interior depth and height. The middle rail separating the openings may need to be larger than the 3” (7.6 cm) minimum shown. Always refer to the individual installation instructions packed with each product for specific requirements.

Warming Drawer Combined with Advantium and Single Oven:

Install a separate 120V, 60Hz, properly grounded receptacle. See installation instructions packed with each product for specific requirements.

3” (7.6 cm) Min.

Installation Instructions

SUITABLE BRACING TO SUPPORT RUNNERS

2" x 4" or EQUIVALENT RUNNERS

21 5/8"

OVER CENTERLINE

OF CABINET

Cutout for 30″ Ovens only

For JTP30, JTP70, PT916, PT920, ZET938 models only.

Cutout

Width

CUTOUT

28 1/2” (72.4 cm)

WIDTH

28 1/2" MIN.

Min.

28 5/8" MAX.

28 5/8” (72.7 cm)

Max.

Allow 11/16” (1.75 cm) for

ALLOW 11/16" FOR

overlap of oven

OVERLAP OF THE

over side edges

OVEN OVER SIDE

of cutout

EDGES OF CUTOUT

21” (53.3 cm)

ALLOW A MINIMUM

Allow a minimum

OF 21" FOR CLEARANCE

of 21” (53.3 cm) for

TO ADJACENT CORNERS,

clearance to adjacent

DRAWERS, WALLS ETC.

WHEN THE DOOR IS OPENED.

corners, drawers, walls, etc. when door is open

21"

NOTE: If marks, blemishes or the cutout opening are visible above the installed oven, it may be necessary to add wood shims under the runners and front trim until the marks or opening are covered.

These ovens are not approved for stackable installations.

Opening Between

THE OPENING

Inside Walls

BETWEEN INSIDE

Must Be

WALLS MUST BE AT LEAST

At Least

28 1/2"WIDE

28 1/2” (72.4 cm) Wide

Allow 1” (2.5 cm)

ALLOW 1" FOR

OVERLAP

minimum for

ON OVEN TOP

overlap of oven

AND BOTTOM

top and 11⁄

OF CUTOUT

(3.2 cm) overlap

of oven bottom

of cutout

CABINET

WIDTH

Cabinet

30” (76.2 cm)

30"

Width

”

(76.2 cm)

7 3/4” (19.7 cm)

Max.

Cutout Height

CUTOUT

27 1/4”

HEIGHT

(69.2 cm) Min.

27 1/4" MIN.

27 5/16”

27 5/16" MAX.

(69.4 cm) Max.

RECOMMENDED

Recommended

CUTOUT

LOCATION

cutout location

32 1/2"

from floor 32 1/2”

FROM THE

(82.6 cm)

FLOOR

Junction Box Location (junction box may be located in

JUNCTION BOX

adjacent

LOCATION

cabinet)

22" TO

22” (55.9 cm)

BOTTOM OF

Min. to

JUNCTION BOX

Bottom of

Junction Box

Suitable Bracing to Support Runners

Side by Side Installations

Install two wall ovens in separate cutouts. Allow 2″ (5.1 cm) min. between cutouts (PT920 models) or 6″ (15.2 cm) min. between cutouts (all other models).

Cutout –

Observe all

dimensions

requirements.

Single Built-In

Cabinet Width 30” (76.2 cm) Recommended

Cutout Location from Floor 32 1/2” (82.6 cm)

Cutout Depth 23 1/2” (59.7 cm) Min. Cutout Width 28 1/2” (72.4 cm) Min.

28 5/8” (72.7 cm) Max.

Cutout Height 27 1/4” (69.2 cm) Min.

27 5/16” (69.4 cm) Max.

NOTE: If the cabinet does not have a front frame and the sides are less than 3/4” (1.9 cm) thick, shim both sides equally to establish the cutout width.

2” x 4” (5 cm x 10 cm) or equivalent runners level with bottom of cutout

21 5/8”

(54.9 cm) Over

Centerline of Cabinet

and

2″ (5.1 cm)

Min. (PT920)

6″ (15.2 cm)

Min.

(other models)

Cutout –

Observe all

dimensions

and

requirements.

Installation Instructions

Cutout for 30″ (76.2 cm) Double Built-In Ovens only

For JTP35, JTP55, JTP75, PT956, PT960, ZET958 models only.

Cutout

Width

CUTOUT

28 1/2” (72.4 cm)

WIDTH

28 1/2" MIN.

Min.

28 5/8" MAX.

28 5/8” (72.7 cm)

Max.

7 3/4”

(19.7 cm)

Max.

Junction Box Location (junction box may be located in adjacent

JUNCTION BOX

cabinet)

LOCATION

Cabinet Width 30” (76.2 cm) Recommended

Cutout Location from Floor 12” (30.5 cm)

Cutout Depth 23 1/2” (59.7 cm) Min.

ALLOW 11/16"

FOR OVERLAP

Allow 11/16”

OF THE OVEN

(1.75 cm) for

OVER SIDE EDGES

overlap of oven

OF CUTOUT

over side edges of cutout

Allow a minimum

ALLOW A MINIMUM OF 21"

of 21” (53.3 cm) for

FOR CLEARANCE TO

clearance to adjacent

ADJACENT CORNERS,

corners, drawers,

DRAWERS, WALLS ETC.

walls, etc. when

WHEN THE DOOR

door is open

IS OPENED.

21” (53.3 cm)

21"

Opening Between Inside Walls

THE OPENING

Must Be At

BETWEEN INSIDE

WALLS MUST

Least 28 1/2”

BE AT LEAST

(72.4 cm) Wide

28 1/2"WIDE

Allow 1” (2.5 cm)

minimum for

overlap of oven

ALLOW 1" FOR

top and 11⁄

OVERLAP

(3.2 cm) overlap

ON OVEN TOP

of oven bottom

AND BOTTOM

OF CUTOUT

of cutout

(76.2 cm)

CABINET

Cabinet

30"

30”

WIDTH

Width

”

47” (119.4 cm)

BOTTOM OF

JUNCTION BOX

Cutout Height

CUTOUT

51 13/16” (131.6 cm)

HEIGHT

Min.

51 13/16" MIN.

51 15/16” (131.9 cm)

51 15/16" MAX.

Max.

Recommended

RECOMMENDED

CUTOUT LOCATION

cutout location

12" FROM THE FLOOR

from floor 12” (30.5 cm)

to Bottom of

Junction Box

47" TO

Min.

Cutout Width 28 1/2” (72.4 cm) Min.

28 5/8” (72.7 cm) Max.

Cutout Height 51 13/16” (131.6 cm) Min.

51 15/16” (131.9 cm) Max.

NOTE: If the cabinet does not have a front frame and the sides are less than 3/4” (1.9 cm) thick, shim both sides equally to establish the cutout width.

2” x 4”

2" x 4" or EQUIVALENT

(5 cm x 10 cm)

RUNNERS

or equivalent runners level with bottom of cutout

If the cabinet does not have a solid bottom, two braces or runners must be installed level with the bottom of the cutout to support the weight of the oven. For double ovens, the runners and braces must support 275 lbs (124 Kg).

NOTE: If marks, blemishes or the cutout opening are visible above the installed oven, it may be necessary to add wood shims under the runners and front trim until the marks or opening are covered.

Suitable Bracing to Support Runners

21 5/8”

21 5/8"

OVER CENTERLINE

(54.9 cm) Over

OF CABINET

Centerline of Cabinet

Installation Instructions

Cutout for 30″ only

For JTP30, JTP70, PT916, PT920, ZET938 models only.

Gas or electric cooktops may be installed over this oven. See cooktop installation instructions for cutout size. See label on top of oven for approved cooktop models.

25” (63.5 cm)

Top and/or side fillers may be necessary if unit is positioned between existing cabinets. Be sure they are attached securely, since they will anchor the oven in the cabinet.

Under Counter

27 1/4” (69.2 cm) Min. 27 5/16” (69.4 cm) Max.

(76.2 cm)

28 1/2” (72.4 cm) Min. 28 5/8” (72.7 cm) Max.

Single Built-In Ovens

240V / 208V Junction Box Location (junction box may be in adjacent cabinet)

Allow 1” (2.5 cm) overlap top of oven, 11/16” (1.8 cm) overlap side edges of cutout and 1 1/4” (3.2 cm) overlap bottom of oven.

7 3/4”

(19.7 cm)

Max.

Gas and electrical connections for 30” (76.2 cm) gas cooktop must be located in an adjacent accessible location to the right. For 36” (91.4 cm) gas cooktop, the connections may be made to the left.

22” (55.9 cm) Min. Above Support Platform

36” (91.4 cm) Typical Countertop Height

3/4” (1.9 cm)

Support Platform

Required

MUST SUPPORT 150 LBS. (68 Kg)

Side by Side Installations

Install two wall ovens in separate cutouts. Allow 2″ (5.1 cm) min. between cutouts (PT920 models) or 6″ (15.2 cm) min. between cutouts (all other models).

Must match toekick height

Cutout –

Observe all

dimensions

and

requirements.

24” (61 cm)

4” (10.2 cm) Typical Toekick

NOTE: This oven is not approved to be installed under a solid disk, induction or downdraft modular cooktop.

2″ (5.1 cm )

Min. (PT920)

6″ (15.2 cm ) Min.

(other models)

Cutout –

Observe all

dimensions

and

requirements.

Cabinetry

Cutout for 30″ Built-In Ovens only – Over a Warming Drawer

For JTP30, JTP35, JTP55, JTP70, JTP75, PT916, PT920, PT956, PT960, ZET938, ZET958 models only.

(76.2 cm)

Single or Double

Single 30″ (76.2 cm) Oven Over a Warming Drawer

Anti-Tip Block Against Rear Wall Per Warming Drawer Requirement

2” (5.1 cm) Min.

NOTE: Install the

oven only with specific models

Per Warming Drawer Requirement

1” (2.5 cm) Min. Above Toekick or Adjust to Oven Installation Height

NOTE: Additional clearances between cutouts

may be required. Check to be sure the oven supports above the Warming Drawer location do not obstruct the required interior depth and height.

listed on the label located on top of the oven.

Double 30″ (76.2 cm) Oven Over a Warming Drawer

Anti-Tip Block Against Rear Wall Per Warming Drawer Requirement

2” (5.1 cm) Min.

Per Warming Drawer Requirement

1” (2.5 cm) Min. Above Toekick

+ 28 hidden pages

GE JKP30SMSS, JKP35WMWW, JKP35BMBB, JKP35SMSS, JKP55BMBB Installation Instructions Manual

Specifications and Main Features

Frequently Asked Questions

User Manual