GE JKP30BM1BB, JKP30BM2BB, JKP30CM1CC, JKP30CM2CC, JKP30SM2SS Installation Guide

...

Built-In Wall Oven

27" (68.6 cm) models JKS10, JKP30, JKP35, JKP55, JKP70, JKP75,

PK916, PK956, ZEK938, ZEK958

Ilnstallat!on

nstruct=ons

If you have questions, call 1.800.GE.CARES or visit our website at: ge.com

30" (76.2 cm) models

JTP30, JTP35, JTP55, JTP70, JTP75, PT916, PT920, PT956, PT960, ZET938, ZET958

Before You Begin

Read these instructions carefully and completely.

• IMPORTANT-save these

instructions for local inspector's use.

• IMPORTANT-observe all

governing codes and ordinances.

• Note to Installer--Be sure to leave these

instructions with the consumer.

• Note to Consumer--Keep these instructions for future reference.

Parts Included

(Appearance will vary)

Screws For Installation (8-18 x .750 flat head

Phillips wood screws)

27" (68.6 cm)

Metal Bottom Trim

• Proper installation is the responsibility

of the installer and product failure due to improper installation is NOT covered under warranty.

• NOTE--This appliance must be properly

grounded.

•ATTENTION INSTALLER

All electric wall ovens must be hard wired (direct wired) into an approved junction

box. A plug and receptacle is NOT permitted on these products.

Materials Needed

Wire Nuts

Strain Relief Clamp Junction for 1/2" conduit Box

WB07T10578 - Black WB07T10579 - SS

Optional 27" (68.6 cm) Metal Bottom Trim Assembly (on some models or can be purchased separately)

31-10647-3 11-07JR

30" (76.2 cm)

Metal Bottom Trim

Assembly

Tools Needed

1/8" (3 mm) Drill Bit and Electric or Hand Drill

36" (91 cm) of String

Phillips Screwdriver

Installation instructions

PORTANT SAFETY I ST CTIONS

For Your Safety

• Be sure your oven is installed properly by a qualified installer or service technician.

• Be sure the oven is securely installed in a

cabinet that is firmly attached to the house structure. Weight on the oven door could cause the oven to tip and result in injury.

Never allow anyone to climb, sit, stand or hang on the oven door.

• Make sure the cabinets and wall coverings around the oven can withstand

the temperatures (up to 200°F [93.3°C]) generated by the oven.

WARNING: The electrical

power to the oven supply line must be shut off while line

connections are being made. Failure

to do so could result in serious injury

or death.

lectrical

Requirements

This appliance must be supplied with the proper

voltage and frequency, and connected to an

individual, properly grounded branch circuit, protected by a circuit breaker or fuse. See the

rating plate located on the oven frame to determine

the rating of the product. Use the chart below to

determine the minimum recommended dedicated circuit protection.

Recommended

KW Rating KW Rating Circuit Size

240V 208V (Dedicated)

<4.8 KW <4.1 KW 20Amp

4.9 KW-7.2 KW 4.3 KW-6.2 KW 30 Amp

7.3 KW-9.6 KW 6.3 KW-8.3 KW 40 Amp

9.7 KW-12.0 KW 8.4 KW-10.4 KW 50 Amp

lectrical

Requirements cont.

Rating plate is located on oven side trim,

side front frame or lower front frame.

Rating Plate

Location

We recommend you have the electrical wiring and hookup of your oven connected by a qualified electrician. After installation, have the electrician

show you where your main oven disconnect is located.

Check with your local utilities for electrical codes which apply in your area. Failure to wire your oven

according to governing codes could result in a hazardous condition. If there are no local codes,

your oven must be wired and fused to meet the requirements of the National Electrical Code,

ANSI/NFPA No. 70-Latest Edition. You can get a copy by writing:

National Fire Protection Association Batterymarch Park

Quincy, MA 02269

Effective January 1, 1996, the National Electrical Code requires that new, but not existing,

construction utilize a four-conductor connection to an electric oven. When installing an electric oven

in new construction, a mobile home, recreational vehicle or an area where local codes prohibit grounding through the neutral conductor,

follow the instructions in the section on NEW CONSTRUCTION AND FOUR-CONDUCTOR BRANCH CIRCUIT CONNECTION.

You must use a three-wire, single-phase A.C. 208Y/120 Volt or 240/120 Volt, 60 hertz electrical

system. If you connect to aluminum wiring, properly installed connectors approved for

use with aluminum wiring must be used.

Insta ion instructions

Pre-lnstallation

ALL INSTALLATION INFORMATION ON THE FOLLOWING PAGES IS TO BF USED FOR SINGLE AND DOUBLE OVEN INSTALLATION!

Remove packaging materials.

Check behind hinges and under false bottom. Remove labels on the

outside of the door, plastic on trims and panel, all tape around the oven, and any shipping screws securing the oven to the base pad.

__ =

Oven Racks

_ iterature

Pack

Chec ist

Door removal is not a requirement for installation of the product, but is an

added convenience. To remove the door:

[_ Open the oven door as far as it will go.

Push both hinge Hinge locks down toward ,_I_:'_L Position

the door frame, Hinge"I_ to the unlocked s_ot_.d

position. This may require a flat blade

screwdriver. Arm

[_ DO NOT LIFT THE DOOR

[_ Place hands on both sides of "_

[_ ift door up and

the door, and close the oven 11_ door to the removal position, t_/

which is most of the way closed, t_'/

out until the hinge arms

clear the slots.

_ :,,_ Unlocked

Hinge

Open oven door and remove literature pack and oven racks.

Remove Installation Instructions from literature pack and read them carefully

before you begin.

Be sure to place all literature, Owner's Manual, Installations, etc. in a safe place

for future reference.

Hinge Clears Slot

NOTE: The oven door is very heavy. Be sure

you have a firm grip before lifting the oven

door off the hinges, Use caution once the door is removed. Do not lay the door on its

handle. This could cause dents or scratches.

Place the oven on a table or platform even with the cutout opening. (Platform must support 150 Ibs. [68 Kg] single, 275 Ibs. [124 Kg] double.)

Remove the bottom trim from the top

of the oven. It will be installed at the end of the installation process. The trim is

wrapped separately and taped to the top of the unit.

Installation instructions

Cutout for 27" (68.6c )Single

Ovens on y

For JKS10, JKP30, JKP70, PK916, ZEK938 models only.

Max. from the

Cabinet_ _sk !_ Junction Box

27" (68.6 cm) i

Cutout Width /_

25" (63.5 cm)

Allow 1" (2.8 era)

for overlap of oven over side

edges of cutout

2" x 4"

(Scmx tOcm)

0¥

runners level

with bottom

of cutout

20" (50.8 era)

Allow a minimum ciearance°f20" (50.8teCta),41 _for overlap of

corners, drawers, wails, bottom etc. when door is open of cutout'_"'_--_

a_jacen, oven top and

Min. j ,,: ,,

25 114" (64.1 "!-'

Max.

" Allow"

1" (2.5 cm)

minimum for

5" (12.7 cm)

left or right

/ Location

Cutout Height 22" (55.9 cm)

27 5/8" Min. above (70.2 cm) Min. base rail

28 118" I

access from

Box Location -

adjacent cabinet

Recommended may be required cutout location

from Roor 32 1/2"

(82.6 cm)

uilt-ln

Cabinet Width

Recommended

Cutout Location from Floor

Cutout Depth

Cutout Width

Cutout Height

NOTE: if the cabinet does not

have a front frame and the sides are less than 3/4" (1.9 cm) thick, shim both sides equally to

establish the cutout width.

27" (68.8 cm)

32 1/2" (82.6 cm) 23 1/2"

(59.7 cm) Min. 25" (63.5 cm) Min.

25 1/4" (64.1 cm) Max. 27 5/8" (70.2 cm) Min.

28 1/8" (71.4 cm) Max.

If the cabinet does not have a solid bottom, two braces or runners must be installed

level with the bottom of the cutout to support the weight of the oven. For

single ovens, the runners and braces must support 150 Ibs (68 Kg).

NOTE: If marks, blemishes or the cutout opening are visible above the installed oven, it may be necessary to

add wood shims under the runners and

front trim until the marks or opening

are covered,

2" x 4" (5 cmx tO cm) or equivalent runners love|

with bottom of cutout

24"

(61cm)

I-'_- 18" (45.7 cm) "-_1

"_ 27" (68,6 cm) "_

These ovens are not approved for stackable installations.

Cutoutfor 27"(68.6 Ovensonly

For JKP35, JKP55, JKP75, PK956, ZEK958 models only.

Allow 1" (2.5 cm) for overlap of

oven over side

edges of cutout

20" (50.8

--_ j°s-

Allow a minimum of 20" (50.8 cm)

for clearance to adjacent corners,

drawers, walls, etc. when door is open

Installation instructions

(12.7 cm)

Max. from the left or

Cabinet right

(68.6 cm) _

Cutout

5" (63.5 cm) Min.

25 1/4" i

i Junction Box

__ Location

(s4.1cm)M_,

icut°ut Above iHeight base rail i49 11116"

i(126.2 cm) IVlin. 150118" i(127.3 cm) Max.

.... Ailo_vI"

(2,5 cm) for overlap of oven from floor 13 114"

top and bottom_ (33.7 cm)

of cutout

Recommended

cutout location

(111.8 cm)

Min.

Cabinet Width

27" (68.6 cm)

Recommended Cutout Location from Floor

Cutout Depth Cutout Width

13 1/4" (33.7 cm) 23 5/8" (60 cm) Min. 25" (63.5 cm) Min.

25 114" (64.1 cm) Max.

Cutout Height

49 11116" (126.2 cm) Min. 50 1/8" (127.3 cm) Max.

NOTE: If the cabinet does not have a front frame and the sides are less than 314"

(1.9 cm) thick, shim both sides equally to establish

the cutout width.

if the cabinet does not have a solid bottom,

two braces or runners must be installed to support the weight of the oven. For double

ovens, the runners and braces must support 300 Ibs (135 Kg).

NOTE: If marks, blemishes or the

cutout opening are visible above the

installed oven, it may be necessary to

add wood shims under the runners and front trim until the marks or opening

are covered.

-- 2" x 4" (ScmxtOcm)

or equiva|ent ruuners level

with bottom of cutout

Suitable Bracing

to Support

Runners

Over Centerline

of Cabinet

Installation instructions

Cutout for 27" (68.6c_)Single Built-in

Ovens only Under Counter

For JKS10, JKP30, JKPT0, PK916, ZEK938 models only.

Gas or electric cooktops may be installed over this oven.

See cooktop installation instructions for cutout size.

See label on top of oven for approved cooktop models.

25" (63.5 cm)

240V / 208V

Junction Box 5"

Location (12.7 cm)

Max. from the

left or right

side

Gas and electrical connections

for gas cooktop must be located

in an adjacent accessible location to the right.

Top and/or side fillers

may be necessary

if unit is positioned between existing

cabinets. Be sure

they are attached securely, since they

will anchor the oven

in the cabinet.

_25" (63.5 cm) Min.

25 1/4" (64.1cm) Max.

27 5/8" (70.2 cm) Min. 28 1/8" (71.4 cm) Max.

_J J

Allow

(2.5 cm)

unit overlap top _,

bottom of

oven, 1" (2.5 cm)

unit overlap side

edges

22" (55.9 cm) Min. Above Support

Platform

4"(10.2 cm) Typical

Toekick

36" (91.4 cm) Typical

Countertop Height

MUST SUPPORT 150 LBS. (68 Kg)

be installed under the specific models I_t

i NOTE: This oven is only approved to I_t

JJJ

Cabinetry

for 27" (68.6c_)Single or

uilt-ln Ovens only- Over a

Drawer

For JKS10, JKP30, JKP35, JKP55, JKPT0, JKP75, PK916, PK956, ZEK938, ZEK958 models only.

Single 27" (68.6 cm) Oven Over

a Warming Drawer

Anti-Tip Block Against Rear Wall Per Warming Drawer Requirement

2" (5.1 cm) Min.

Per Warming

Drawer

Requirement J

1" (2.5 cm) Min. Above Toekick or Adjust to Oven Installation Height

NOTE: Additional clearances between cutouts may be required. Check to be sure the oven

supports above the Warming Drawer location do not obstruct the required interior depth and height.

NOTE: Install the oven only with

specific models listed on the label

located on top of the oven.

Double 27" (68.6 cm)

Oven Over

a Warming Drawer

Anti-Tip Block Against Rear

• Wall Per

Warming

Drawer

Requirement

2" (5.1 era)

Min,

Per Warming

Drawer Req=

1" (2.5 cm) Min. Above Toekick

When installing a Warming Drawer below a single or double oven, a separate 120V, 60 Hz, properly grounded receptacle must

be installed. Refer to installation instructions packed with the Warming Drawer for

specific installation requirements.

Cabinetry

Cutoutfor 27"(68.6o_)SingleOvensonly-

BelowanAdvantiumor ;rowave Oven

or BetweenanAdvantiumor crowave

OvenandaWarmingDrawer

For JKS10, JKP30, JKP70, PK91& ZEK938 models only.

Single 27" (68.6 cm) Oven

Below an Advantium or

Microwave Oven

Per Advantium or

Microwave Oven

Requirement

NOTE: The middle rail separating the two

openings may need to be larger than the 3" (7.6 cm) minimum shown. Always refer to the individual installation instructions packed with each product for specific requirements.

Combined Advantium or Microwave Oven and Wall Oven Installation:

When installed in combination with a single wall oven, use separate electrical

junction boxes.

Refer to the Advantium or microwave

oven installation instructions for electrical requirements of that product.

These connections must be made by a qualified electrician. All electrical

connections must meet National Electrical Code or prevailing local codes.

2" (5.1 cm) Min.

Note: Install the oven only with

specific models listed on the label

located on top of the oven.

Single 27" (68.6 cm) Oven

Between an Advantium or Microwave Oven and a

Warming Drawer

Per Advautium or Microwave Oven

Requirement

Per Warming

Drawer

Req

NOTE: Additional clearances may be required. Check to be sure the oven

supports above the Warming Drawer

do not obstruct the required interior depth

and height. The middle rail separating the openings may need to be larger than the 2"

(5.1 cm) minimum shown. Always refer to the individual installation instructions packed with each product for specific requirements.

WarmingDrawerCombinedwith Advantiumor MicrowaveOvenand

SingleOven:

Install a separate 120V, 60Hz, properly

grounded receptacle. See installation

instructions packed with each product for specific requirements.

2" (5.1 cm) Min.

Installation instructions

Cutoutfor 30"(76.2c )Sing Built-in

Ovensonly

For JTP30, JTP70, PT916, PT920, ZET938 models only.

Allow 11/16" (1.75 cm) for

overlap of oven

over side edges of cutout

21 "

(53.3 cm)I'Y_'_ -

Allow a minimum of 21" (53.3 cm) for

clearance to adjacent

corners, drawers,

walls, etc. when

door is open

Cutout

Width

28 1/2" (72.4 cm)

5/8"(72.7ore)

Max.

Opening

Between inside Walls Must Be At Least

28 1/2"

(72.4 cm) Wide

_AIl_w 1" (2.5 cm)

minimum for

overlap of oven

top and 1V4"

(3.2 cm) overlap

of oven bottom

of cutout

_--_ Cabinet

Width

30" (76,2 cm)

9 1/2" (24.1 cm)

I adjacent I / cabinet)

(69.2 cm) Min, 27 5/16"

(69.4 cm) Ma

Recommended cutout location

from floor 32 1/2" (82,6 cm)

if the cabinet does not have a solid bottom, two braces or runners must be installed

level with the bottom of the cutout to support the weight of the oven. For single

ovens, the runners and braces must support 150 Ibs (68 Kg).

NOTE: if marks, blemishes or the

cutout opening are visible above the

installed oven, it may be necessary to

add wood shims under the runners and front trim until the marks or opening

are covered,

Junction Box Location

(junction box

may be

located in

---t

22" (55.9 cm)

Min. to

Bottom of

Junction Box

---4

Suitable

Bracing

to Support

Runners --

Side by Side Installations

Install two wall ovens in separate cutouts.

Allow 2" (5.1 cm) min. between cutouts.

Cabinet Width

30" (76.2 cm)

Recommended Cutout Location from Floor

Cutout Depth Cutout Width

32 1/2" (82.6 cm) 23 1/2" (59.7 cm) Min. 28 1/2" (72.4 cm) Min. 28 518" (72.7 cm) Max.

Cutout Height

27 1/4" (69.2 cm) Min. 27 5/16" (69.4 cm) Max.

Ill not have a front frame and the t_1sides are less than 314" (1.9 cm)

-- 2"x4"

(5 cm x 10 cm or equivalent

runners level

with bottom of cutout

-_(s4 21s/8- .9cm)over \

Centerline of Cabinet

These ovens are not approved for stackable installations.

Cutout- i 2"(5.1 cm)

Observe all Min. dimensions I_ll'='=='==='='=i_

and I

requirements.J

Cutout -

Observe all

dimensions

and

requirements.

Installation instructions

Cutoutfor30"(76.2cm)

For JTP35, JTP55, JTP75, PT956, PT960, ZET958 models only.

Allow 11116"

(1.75 cm) for

overlap of oven .__ over side edges

of cutout

Allow a minimum of 21" (53.3 cm) for clearance to adjacent

corners_ d rawers_

walls, etc. when door is open

21" (53.3 cm)_

Cutout

Width

28 1/2" (72.4 cm)

Min. -,_

28 5/8" (72.7 cm)

Max.

Between I

Inside Walls I

Must Be At

Least 28 1/2"

(72.4 cm) Wide

AHow 1" (2.5 cm)

minimum for

overlap of oven

top and 11/4" (3 2 cm) over ap Max

of oven bottom - I

_t Location

Cutout

Height 51 13/16" 131.6 cm)

Min. 51 15/16" (131.9 cm)

9 1/2"

(24.1 cm) Junction Box

n cabinet)

ofcutout " F- _-I

(junction box may be

located in

adjacent

47" (119.4 cm)

Min.

to Bottom of

Junction Box

Ovensonly

Cabinet Width Recommended

Cutout Location

from Floor

Cutout Depth Cutout Width

Cutout Height

NOTE: If the cabinet does not have a front frame and the sides

are less than 314" (1.9 cm) thick, shim both sides equally to

establish the cutout width.

30" (76.2 cm)

12" (30.5 cm) 23 1/2" (59.7 cm) Min. 28 1/2" (72.4 cm) Min. 28 5/8" (72.7 cm) Max. 51 13/16" (131.6 cm) Min. 51 15116" (131.9 cm) Max.

--_ 30_ I cutout location (76.2 cm)"_;,_from f!oor 12" (30.5 cm)

Cabinet _'_..L,_.

Width I

/1 Recommended

if the cabinet does not have a solid bottom, two braces or runners must be installed

level with the bottom of the cutout to

support the weight of the oven. For double ovens, the runners and braces

must support 275 Ibs (124 Kg).

NOTE: If marks, blemishes or the

cutout opening are visible above the

installed oven, it may be necessary to

add wood shims under the runners and front trim until the marks or opening

are covered,

Suitable Bracing --

to Support

Runners

-- 2"x4"

(Scm xtOcrn)

or equiva|eut

runners |eve|

with bottom of cutout

Installation instructions

Cutoutfor 30"(76.2 Single lit-in

only Under Coun :r

For JTP30, JTPT0, PT916, PT920, ZET938 models only.

Gas or electric cooktops may be installed over this oven. See cooktop installation instructions for cutout size. See label on

top of oven for approved cooktop models.

25" (63.5 cm)

Top and/or side fillers may be necessary if unit is positioned between existing

cabinets. Be sure they are attached

securely, since they will anchor the oven in the cabinet.

- 28 1/2" (72.4 cm) Min. 28 5/8" (72.7 cm) Max.

240V / 208V Junction Box

Location (junction box may be in adjacent cabinet)

9 1/2"

(24.1 cm)

overlap top

Of oven_

-. 11/16" (1.8 cm)

_,"- overlap side edges

of cutout and

-- 1 114" (3.2 cm)

overlap bottom

Of oven,

(2.5 cm)

Ovens

Gas and electrical connections for gas cooktop must be located in an adjacent accessible

location to the right.

22" (55.9 cm) Min.

Above Support

Platform

36" (91.4 cm) Typical Countertop Height

Side by Side Installations

Install two wall ovens in separate cutouts.

Allow 2" (5.1 cm) min. between cutouts.

NOTE: This oven is only approved to be installed under the specific models as labeled

on this unit.

Cutout - ] 2" (5.1 cm)

Observe all| Min. dimensions_-,ql,,,,===,,,===,=,lm_"

and |

requirements.J

Observe all

dimensions

requirements.

Cutout -

and

24" (61 cm)

4" (10.2 cm) Typical

Toekick

Cabinetry

Cutout for 30"(76.2c_)Single or

For JTP30, JTP35, JTP55, JTP70, JTP75, PT916, PT920, PT956, PT960, ZET938, ZET958 models only.

Single 30" (76.2 cm) Oven Over a Warming

Drawer

Per Warming

Drawer

Requirement

L_i-in Ovens only- Over a

_rrning Drawer

Double 30" (76.2 cm) Oven Over a Warming

Drawer

Rear Wall Per Warming Drawer Requirement

Block Against

2" (5J cm) IVlin.

NOTE: Install the oven only with

specific models listed on the label

located on top of the oven.

Per Warming

Drawer

Requirement

Double

Anti-Tip Block

Against Rear Wall Per

Warming

Drawer

Requirement

2" (5.1 cm)

IVlin.

1" (2.5 cm) Min. Above Toekick or

Adjust to Oven Installation Height

NOTE: Additional clearances between cutouts may be required. Check to be sure the oven

supports above the Warming Drawer location do not obstruct the required interior depth and height.

1" (2.5 cm) Min. Above Toekick

When installing a Warming Drawer below a single or double oven, a separate 120V, 60 Hz, properly grounded receptacle must

be installed. Refer to installation instructions packed with the Warming Drawer for

specific installation requirements.

+ 28 hidden pages