Installation
Instructions
Built-In
Microwave/Convection
and
Microwave Ovens
Models
ZMC1095
./_:gz055
Before you begin- Readthese instructions completely and carefully.
IMPORTANT:Savethese instructions for local inspector's use.
IMPORTANT:OBSERVEALLGOVERNINGCODESAND ORDINANCES,
NOTETOINSTALLER:Be sureto leave these instructions with the consumer
NOTETOCONSUMER:Keepthese instructions with your Use and Care Bookfor future reference.
hnportant
S(qety
h brmation
If you have questions concerning the installa-
tion of this product, call the GE Answer
Center@ Consumer lnfi_rmation Service at
800.626.2000, 24 hours ada> 7 clays a week.
If vou received a damaged oven, you should
contact your dealer.
Safety Instructions
This product requires a three prong
grotmded receptacle. The installer must
perform a ground continuity check on the
power outlet box befiwe begim_ing the
installation to insure that the outlet box is
properly grounded. If not properly grounded,
oi" if the outlet box does not meet the
electrical requirements noted, (under
ELECTRICAI_ REQUIREMENTS), a qualified
electrician should be employed to correct anv
deficiencies.
CAUTION: Forpersonal safety, removehouse fuse or ovencircuit
breakerbefore begieeieg iesta%tion to avoidsevere orfatal
shock injury.
CAUTION: Forpersonalsafety,the mountingsurface must be
capable of supporting the cabinet load, in addition to the added
weight of this 70 poued product,plus additional oveeloadsof up
to 50 pouedsor a total weight of 120pounds.
CAUTION: Forpersonalsafetythis productcannot beinstalled in
cabinetarrangements suchas ae island,apeninsula or below
acountertop.
Proper installation is the responsibility of the
installer. Product failure due to improper
installation is not covered under the GE
Appliance _:alTantv. See the Use & Care
Guide tor warranty information.
Electrical Requirements
Product rating is 120 w_lts AC, 60 Hertz, 13
amps. mad 1.45 kilowatts. This product must
be com_ected to a supply circuit of the proper
voltage and fl'equency, Wire size must con-
fiwm to the requirements of the National
Electric Code or the prevailing local code tor
this kilowatt rating. The power supply cord
and plug should be brought to a separate l 5
or 90 ampere branch circuit single grotmded
receptacle, The outlet box should be located
near the cord entry point, The outlet box and
supply circuit should be installed by a quali-
fied electrician and conliwm in the National
Electric Code or the prevailing local code.
Usage: Can be installed over any GE single
electric built-in oven.
Con_n_
DesignInformation
Product Dimensions.........................................................................................................................................................................3
Cutout Dimensions ...........................................................................................................................................................................3
Electrical Locations .........................................................................................................................................................................3
Advance Planning ............................................................................................................................................................................3
Installation
Installation Option ............................................................................................................................................................................4
Tools and Materials Required........................................................................................................................................................4
Parts Supplied ...................................................................................................................................................................................4
Step 1, Slide Microwave into the Cutout......................................................................................................................................4
Step2, Remove Grille Retainer Screws ........................................................................................................................................5
Step3, Install Side Trim for 30"Appearance ...............................................................................................................................5
Step4, Drive Installation Screws ..................................................................................................................................................5
Step5, Reinstall Grille......................................................................................................................................................................6
Models ZMC1095,.]EB 1095, JEB 1055
Axailable in _ hire, Black and Stainless Steel
Design InR)rmation
Built-In Microwave/( onveclion Oven
Product
Dimensions
+ t6-3/8"
t 5-3/8':
[ :$
i
13/16'_
Cutout
Dimensions 17"Min.
forFlush
Outlet
J
Min 3/8"Plywood
Supportedby
2x4or1 x2
Runners,all
FourSides
t 29-3/4"WithOptionalSideTrim +
l l
l_ %-3/4'; ¢J
1-7/8"Min.
SerOven
Requirement
J
ConstructBase
Min3/8"Pbwood
Supportedby
2x4or1 x2
Runners,aJ[
FourSides
Electrical
Location
Advance
Planning
Locateoutletboxintheshadedarea
These microwave ovens are sized to fit a 27"
wide cabinet.
• Side trim pieces are provided fiw installation
into a 30" wide space. For a matching
appearance, use the side trim when installing
the microwave oven above a 30" single wall
o','en,
• If you are installing into a 27" wide cabinet,
or over a 27" wide wall oven, discard the side
trim pieces.
• Cutout dimensions are the same fin" both 27"
or 30" wide cabinet installations,
Installation
Built-In Microwave/Convection Oven
hl,stallation
Options
These built-in ()veils can be inset into the
cabinetry. In this installation tire microwave is
recessed and flush with tire flxmt surfilce of
the cabinet.
A shadow box affect can be achiex ed bv
installing a rail at tire top and bottom of tire
micro_ax e to fill the cutout height, In this
.... _. Sq.
StopperStrip4 sides
Inset/Recessed Installation
• Cut 4 stopper strip s, 13/16" square to fl'ame
the opening, install the strips 13/16" fl'om
the fl'ont edge of the opening. Oven overlap
will cover all 4 stopper strips.
installation, exposed inside surfilces of the
cabinet should be finished to match the
cabinet surfilce.
• In both a recessed and shadow box
installation, the floor of the cutout must be
level and even with the bottom edge of the
cutout. Use rmmers inside tire opening to
raise the floor to matching height.
...........J
Top
Rail
Bottom
Rail
Shadow Box Installation
• Cut top and bottom rail to fit the width of
the opening. Cut the height of the rails to fit
the cutout height. Use cleats to secure the
rails to the inside walls of the cabinets.
Ste 1
SS:de the
Mioowave
into Cutout
Tools and Materials required:
• #2, Phillips screwdriver
• Hand held drill motor
• High speeddrill bit, 1/8"
diameter
• Lift and hold the oven up to the opening.
• Hold the oven at the 45 ° angle and plug in
the power cord.
• Carefiflly, slide the oven into the cabinet.
• Check to be sm'e that power cord is not
trapped under the bottom or the sides of the
()veil,
• 2 each#8x1"- Roundhead
wood screws
• 3/8", slotheadscrewdriver
Parts supplied:
• 2 mounting screws
• 4 extra side trim screws
• 2 side trim pieces
Remove Gidlle
Beta|no Screws
Design hfformation
hbxill-In Micl'OWaV¢/( onv¢clion Oven
• Open tile door.
• Reinoxe tile _\x(i (2) retainer screx_s fl'om tile
bottoin side of tile grille (one at each side).
• Roll tile grille fi)r\_,ard fix)in tile bottoIn.
• Disengage tile locating tabs, and remox e tile
grille flxiin tile unit.
Note: Grilleappearancevaries
dependingonmodel.
Install Side
Trim Jbr 30"
Appearance
St
Drive
Installation
S€iye_/)s
If you are installing in a 27" opening, skip this
step and discard tile optional side triin.
For a 30" installation appearance:
• Slide one side of tile (wen ()tit of tile opening
about 4" to 5", leaving tile opposite side
against the cabinet. Tile oven should be at
about 30° angle in tile opening which will
allow easier access to tile side triin screws.
• Reinove tile two side triin screws.
• Hold a side triIn piece against tile oven with
screw holes aligned. Reinstall original screws.
Note:4extrasidetrimscrewsareprovidedforyourconvenience.
• Lift tile ()veil by tile bottoin, pull out and
turn tile ()veil to expose tile opposite side.
• Using tile installation holes as a guide, drill
two (2) pilot holes (1/8" diameter) into tile
cabinet.
• Install tile two (2) installation screws.
CAUTION: Placetape or
cardboard overtrim edgesto
prevent damagewhile drilling
pilot holes.
CAUTION:LIFTTHEOVENFROMTHEBOTTOM.DONOT
LIFTTHEOVENWITHTHESIDETRIM.
Sidetrimwill notsupporttheweightoftheoven,
• Reinove tile two side triin screws and install
the opposite side triIn piece.
• Careflilly, lift tile oven bv tile bottoIn and
slide straight back into tile opening. Check
to be sure power cord is not trapped beneath
tile ()veil.
t ..............
5
Reinstall
Grille
Installation
Built-I_ Microwave/( o.vectio_ Ove_
• Reinstall the grille, with the m'o retainer
screws.
Notes
Buill-I_ Microwave/( o_veclio_ Ove_
Pub.No.49-8978 SPECIFICATIONSSUBJECTTOCHANGEWITHOUTNOTICE DWG. NO.164D3333P205
(N.D.322) 5/99
Printed inKorea
Loading...