HDA2000ZWH—Built-In Dishwasher
Dishwasher Dimensions (in inches) |
Installation Information |
|
(in inches) |
25-1/8* 24
23-3/8*
24-3/4
34" MIN. adj. to 35"
21-1/2* |
|
*Add 1/4" for |
|
|
*rear insulation |
|
3-1/4 |
4 (Adjustable) |
|
|
Electrical Rating |
|
Voltage AC....................................................... |
120 |
Hertz .................................................................. |
60 |
Total connected load amperage....................... |
8.6 |
Calrod® heater watts....................................... |
500 |
For use on adequately wired 120-volt, 15-amp circuit having 2-wire service with a separate ground wire. This appliance must be grounded for safe operation.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
90° |
|
|
|
|
|
|
|
|
|
|
|
|
24" |
|
||||
|
|
|
|
|
|
|
MIN. |
|||
Hot |
|
|
|
|
|
|
|
|
||
|
|
|
|
|
|
|
|
|||
|
|
|
|
|
|
|
|
|||
water |
|
|
|
|
|
|
|
|
||
34-1/2±1/4" |
|
|
||||||||
line on |
6 |
|||||||||
Underside |
||||||||||
left |
||||||||||
of countertop |
|
|||||||||
|
|
to floor |
|
|||||||
2
|
|
Countertop |
|
This wall area |
|
|
must be free of |
90° |
|
pipes or wires |
|
4 |
4 |
Electrical |
|
|
wiring is |
|
4 |
3" from |
5 |
5 |
cabinet |
|
||
|
|
Electrical |
|
6 |
wiring on |
|
|
right |
Plumbing and electrical service must enter inside shaded area
19" MIN. from wall |
24" From wall |
24" MIN.
Note: Dishwasher must not be installed more than 10' from sink for proper drainage. All plumbing and electrical work must be in accordance with local codes. Dishwasher includes drain hose and leveling legs.
Installation Information: Before installing, consult installation instructions packed with product for current dimensional data.
Wood Insert Cut-Out
Dimensions (in inches)
|
|
|
|
|
|
|
|
|
|
|
|
Door insert |
|
|
A |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Access insert |
C |
|
|||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
B |
|
|
|
|
|
|
|
|
Panel |
|
|
|
|
|
|
|
|
|
|
|
|
||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Models/Kits |
A |
B |
|
C |
Thickness |
||||||||
GPF325 Kit |
18-7/8” |
23-9/16” |
3-11/16” |
1/4” |
|||||||||
|
|
|
|
|
|
|
|
|
|
4-1/4” to |
|
||
GPF375 Kit |
18-15/16” |
23-5/8”* |
3-3/4”** |
3/4” |
|||||||||
*Bottom of panel must be notched 1-1/2" x 1/2" to clear across panel
**Adjustment required to match adjcent cabinets fronts due to leveling leg adjustment, 4" nominal.
For answers to your Monogram,®GE Profile Performance Series,™ GE Profile,™ GE, Hotpoint and RCA appliance questions, call GE Answer Center® service, 800.626.2000.
Listed by
Underwriters
R Laboratories
Created 8/97
Loading...