GE GTD18ESSJ2WW, GTD18GSSJ2WW, GTD42EASJ0WW, GTD42EASJ1WW, GTD42GASJ0WW Installation Guide

...

Installati

Dryers

Instructi

i Ouestions? Call800.GE.CARES {800.432.2737)orvisitour Web siteat:GEAppliances.com i

This isthe safety alert symbol. This symbol alerts you to potential hazards that can kill you or hurt you and others.

All safety messages will follow the safety alert symbol and the word "DANGER","WARNING", or "CAUTION".These words are defined as:

Indicates a hazardoussituation which, if not avoided,will resultin death or seriousinJury. Indicates a hazardoussituation which, if not avoided, could result indeath or seriousinjury. Indicates a hazardoussituation which, if not avoided, could result inminor or moderate injury.

BEFORE YOU BEGIN

Readthese instructions completely and carefully.

• IMPORTANT-save these instructions for local

electrical inspector's use.

• IMPORTANT- Observeallgoverning codesand

ordinances.

• Installthe clothes dryer according to the manufacturer's instructions and local codes.

• Note to Installer - Be sure to leavethese instructions with the Consumer.

• Note to Consumer - Keepthese instructions for future reference.

• Clothes dryer installation must be performed by a qualified installer.

• Thisdryer must be exhausted to the outdoors.

• Before the old dryer is removed from service or discarded, remove the dryer door.

• Service information and the wiring diagram are located in the control console.

• Do not allow children on or inthe appliance. Close supervision of children isnecessary when the appliance

is used near children.

• Proper installation isthe responsibility of the installer.

• Product failure due to improper installation is not covered under the Warranty.

• Install the dryer where the temperature is above 50°F for satisfactory operation of the dryer control system.

• Remove and discard existing plastic or metal foil duct and replace with UL-listed duct.

- Fire Hazard

• Clothes dryer installation must be performed by a qualified installer.

Install the clothes dryer according to these

instructions and local codes.

DO NOT install a clothes dryer with flexible plastic

venting materials. If flexible metal (semi-rigid or foil-type) duct is installed, it must be UL-listed and

installed in accordance with the instructions found in "Connecting the Dryer to House Vent" later in

this manual. Flexible vent materials are known to collapse, be easily crushed and trap lint. These

conditions will obstruct dryer airflow and increase the risk of fire.

DO NOT install or store this appliance in any

location where it could be exposed to water or weather.

To reduce the risk of severe injury or death, follow all installation instructions.

Save these instructions. (Installers: Be sure to leave these instructions with the customer.)

Printed in Me×ico

234D2318P001

31-16767-Io5-15GE

Installation Instructions

StateofCaliforniaProposition65 Warnings:

TheCaliforniaSafeDrinkingWater and Toxic EnforcementAct requiresthe governor of Californiato publisha list of substances

known to the state to cause cancer, birth defects or other reproductive harm and requiresbusinessesto warn of potential exposure

to suchsubstances.

Thisproduct contains one or morechemicals known to the Stateof Californiato causecancer, birth defectsor

other reproductive harm.

Gasappliances cancause low-level exposureto some ofthese substances,including benzene,carbon monoxide, formaldehyde and soot,caused primarily by the incompletecombustion of natural gas or LPfuels. Exposureto these substancescan be minimized by

properlyventing the dryer to the outdoors.

UNPACKING YOUR DRYER

Tilt the dryer sideways and remove the foam shipping pads by pulling at the sides and breaking

them away from the dryer legs. Be sure to remove all

of the foam pieces around the legs. Remove literature and bag containing accessories.

ROUGH-IN 27" DIMENSIONS ------ (68.8 cm)

Cubic × y

Foot

43 3/8" 26 3/4"

6.0 (110 cm) (68 cm) 43 3/8" 29 1/2"

7.0 (110 cm) (75 cm) 43 3/4" 30 1/2"

7.3 (111cm) (78 cm)

Front View

STEAM WATER HOSES:

GEstrongly recommends the useof factory specified parts. Thesehosesare manufactured andtested to meet GE

specifications. GEstrongly recommends the useof new water supply hoses.

Hosesdegrade overtime and need to bereplaced every 5

years to reducethe risk of hose failures and water damage. Parts end Accessories

Order on-line at GEAppliencePorts.com, 24 hours a day or by phone at 800.626.2002during normal businesshours.

Pert Number WE25X20060

OR WEltq847

WE01X22395 plVll4X100%

WX14X10007

.................. -4--

Side View \_

4 1/4"

(10.8cm)

Accessory CompleteKit(hoses,Y-adapter

washers)(included)

LongHoseand ShortHose

Dryerdooropeningventbrush (notincluded)

LintEaterTM Dryerrotarytube brush (notincluded)

_14 s/8"

1.7 cm)

Installation Instructions

REQUIREMENTS FOR ALCOVE OR CLOSET INSTALLATION

_- Explosion Hazard

Keepflammable materials and vapors, such as gasoline,

away from dryer.

Placedryer at least 18" (/46cm) above the floor for a

garage installation.

Failureto do so can result in death, explosion, or fire.

,, If the dryer is approved for installation in an alcove or

closet, it will be stated on a label on the dryer back.

• The dryer MUST be vented to the outdoors. See the EXHAUSTING THE DRYERsection.

• Minimum clearance between dryer cabinet and adjacent walls or other surfaces is:

0" either side 3" front

0" rear but a 1" minimum is recommended

Minimum vertical space from dryer to overhead

shelves, cabinets, ceilings, etc., is 1" on top. Consideration must be given to provide adequate

clearance for installation and service. Closet doors must be Iouvered or otherwise

ventilated and have at least 60 square inches of open area. If the closet contains both a washer

and a dryer, doors must contain a minimum of

120 square inches of open area.

NOTE: WHEN THE EXHAUST DUCT IS LOCATED IN THE REAR OF THE DRYER,THE CONFIGURATION OF THE DUCTING MAY REQUIRE GREATER THAN 0" OF

REARCLEARANCE.A 1" MINIMUM ISRECOMMENDED.

Gas Dryers Only:

• No other fuel burning appliance shall be installed in the same closet as a gas dryer.

The dryer must be disconnected from the gas supply piping during pressure testing at pressures

greater than 1_ psi (3.5 kPa). A 1/8 inch NPT minimum plugged tapping,

accessible for test gauge connection, must be installed immediately upstream of the gas supply

connection to the dryer.

MINIMUM CLEARANCE OTHER THAN

ALCOVE OR CLOSET INSTALLATION

Minimum clearance to combustible surfaces and

for air opening are: 0" both sides; 1" front; 0" rear

but a 1" minimum is recommended. Consideration must be given to provide adequate clearance for

installation and service.

MOBILE OR MANUFACTURED HOME INSTALLATION

• Installation must conform to the MANUFACTURED HOME CONSTRUCTION AND SAFETYSTANDARD, TITLE 2/4, PART 32-80 or Standard CAN/CSA-Z240 MH, or, when such

standard is not applicable, with AMERICAN NATIONAL STANDARD FOR MOBILE HOME,

ANSI/NFPA NO. 501B. The dryer MUST be vented to the outdoors. The

exhaust vent must be securely fastened to a non-combustible portion of the mobile home.

The vent MUST NOT be terminated beneath a

mobile or manufactured home.

• The vent duct material MUST BE METAL.

• KIT 14-D346-33 MUST be used to attach the dryer securely to the structure.

• The vent MUST NOT be connected to any other duct, vent or chimney.

• Do not use sheet metal screws or other

fastening devices which extend into the interior

of the exhaust vent.

• Provide an opening with a free area of at least 25 square inches for introduction of outside air into the dryer room.

• See the sections for electrical connection information.

POWER CORDS:

GEstrongly recommends the useof factory specified parts. Selectthe power cord to fit your installation requirements.

Order on-line at GEApplianceParts.com, 24 hours a day or by phone at 800.626.2002during normal businesshours.

Part Number Type Length Amperage

WX9X2 ]5-Prong 4 Feet 30 WX9X3 3-Prong 5 Feet 30

WX9X4 3-Prong 6 Feet 30

WX9X!8 4-Prong 4 Feet 30 WX9X!9 4-Prong 5 Feet 30

WX9X20 4-Prong 6 Feet 30

Installation Instructions

CONNECTING INLET HOSES

CONNECTING INLET HOSES (on some models)

To produce steam, the dryer must connect to the cold water supply. Since the washer must

also connect to the cold water, a "Y" connector

is inserted to allow both inlet hoses to make that

connection at the same time.

NOTE: Use the new inlet hoses provided; never use

old hoses.

Turn the cold water faucet off. Remove the washer inlet hose from the washer fill valve

connector (cold).

Ensure the rubber flat washer is in place and attach one female coupling of the short hose onto the washer fill valve connector. Tighten by

hand until firmly seated.

Attach one male end of the "Y" connector to the other female coupling of the short hose. Ensure

the rubber flat washer is in place. Tighten by

hand until firmly seated.

CONNECTING INLET HOSES

Ion some models)(cont.}

7. Using pliers, tighten all the couplings with an additional two-thirds turn.

NOTE: Do not overtighten. Damage to the couplings may result.

Insert the filter screen in the coupling of the

washer's inlet hose. If a rubber flat washer is already in place remove it before installing the

filter screen. Attach this coupling to one male end of the "Y" connector. Tighten by hand until firmly

seated.

Ensure the rubber flat washer is in

attach the dryer's long inlet hose to end of the "Y" connector. Tighten by

place and

one male

hand until

firmly seated.

Ensure the rubber flat washer is in

attach the other end of the dryer's

hose to the fill valve connector at the

the dryer back panel. Tighten by hand

place and

long inlet

bottom of

until firmly

seated.

8. Turn the water faucet on.

9. Check for leaks around the "Y" connector, faucet and hose couplings.

WATER SUPPLY REQUIREMENTS

Hot and cold water faucets MUST be installed

within 42 in. (107 cm) of your washer's water inlet. The faucets MUST be 3/4 in. (1.9 cm) garden

hose-type so inlet hoses can be connected. Water pressure MUST be between 10 and 120 pounds per square inch. Your water department can

advise you of your water pressure.

NOTE: A water softener is recommended to reduce buildup of scale inside the steam generator if the

home water supply is very hard.

Installation Instructions

CONNECTING A GAS DRYER(ski

TOOLS YOU WILL NEED

010" Adjustable 0 Flat-blade

wrenches (2) screwdriver

17Level

178" Pipe wrench

17Slip-joint pliers

MATERIALS YOU WILL NEED

174" dia. metal elbow

174" dia., UL-listed

flexible metal duct (if needed)

) for electric dryers}

Before beginning the installation, turn off the circuit breaker(s) or remove the dryer's circuit fuse(s) at the electrical box. Be sure the dryer cord is unplugged from the wall.

Turn the dryer's gas shut-off valve in the supply line to the OFF position.

17Pipe compound or

PTFEtape

13Flexible gas line

connector

17Duct clamps (2) or

Spring clamps (2)

0 Safety glasses

174" dia. metal duct

(recommended)

)

174" Cover Plate (Kit

WE1H454)

17Gloves

17Soap solution for

leak detection

0 Exhaust hood

17Duct tape

17Gas pipe adapters (2),

elbow and pipe plug

Shut-off Valve

Disconnect and discard old flexible gas connector and ducting material.

Installation Instructions

CONNECTING A GAS DRYER(ski

GAS REQUIREMENTS

_ Explosion Hazard

Use a new CSA International approved flexible

gas supply line. Never reuse old flexible connectors.

Install a shut-off valve.

Securely tighten all gas connections.

If connected to LPgas, have a qualified person make sure gas pressure does not exceed 13"

water column.

• Examples of a qualified person include: licensed heating personnel, authorized gas company personnel, and authorized service personnel.

Failure to do so can result in death, explosion,

or fire.

This gas dryer is equipped with a valve and

burner assembly for use only with natural gas. Using conversion kit WE2SX217,your local service

organization can convert this dryer for use with

propane (LP)gas. (To convert from propane (LP)

to natural gas, conversion kit WE25X218 will be

utilized.) ALL CONVERSIONS MUST BE MADE BY PROPERLYTRAINED AND QUALIFIED PERSONNEL

AND IN ACCORDANCEWITH LOCALCODESAND ORDINANCE REQUIREMENTS.

DRYER GAS SUPPLY CONNECTION

for electric dryers)(cont.)

GAS SUPPLY

A 1/8" National Pipe Taper thread plugged tapping, accessible for test gauge connection,

must be installed immediately upstream of the gas supply connection to the dryer. Contact

your local gas utility should you have questions

on the installation of the plugged tapping. Supply line is to be 1/2" rigid pipe and equipped

with an accessible shutoff within 6 feet of, and

in the same room with, the dryer. Use pipe thread compound appropriate for

natural or LP gas or use PTFEtape. Connect flexible metal connector to dryer and

gas supply.

The installation must conform with local codes,

or in the absence of local codes, with the National Fuel Gas Code, ANSI Z223.1/NFPA 54,

or the Natural Gas and Propane Installation Code, CSA B149.1.

IN THE COMMONWEALTH OF MASSACHUSETTS

This product must be installed by a licensed

plumber or gas fitter.

When using ball-type gas shut-off valves, they shall be the T-handle type.

A flexible gas connector, when used, must not exceed 3 feet.

1-7/8"

3-1/8"

3/8"NPTMALETHREADGASSUPPLY

NOTE:Addtoverticabdimension

thedistancebetweencabinet

bottomtofloor.

You must use with this dryer a flexible metal connector (listed connector ANSI Z21.24/CSA 6.10).

The length of the connect shall not exceed 3 ft.

ADJUSTING FOR ELEVATION

Gas clothes dryers input ratings are based on sea level operation and need not be adjusted for operation at or below 2000 ft. elevation. For operation at elevations above 2000 ft., input

ratings should be reduced at a rate of 4 percent

for each 1000 ft. above sea level.

Installation must conform to local codes and

ordinances or, in their absence, the NATIONAL

FUEL GAS CODE, ANSI Z223.

Installation Instructions

CONNECTING THE DRYER TO THE GAS SUPPLY

Install a female 3/8" NPT elbow at the end of the

dryer gas inlet. Install a 3/8" flare union adapter to the female

elbow. IMPORTANT: Use a pipe wrench to securely hold

on to the end of the dryer gas inlet to prevent

twisting the inlet.

NOTE: Apply pipe compound or PTFEtape to the

threads of the adapter and dryer gas inlet.

New Metal

Flexible Gas _

LineConnector ___. _

AdGpter_ _ _

Elbow _

Items not supplied

r_ Attach the flexible metal gas line connector to

the adapter.

3/8" NPT

_pj Adapter

1/8" NPT Pipe Plug for

Checking Gas

Inlet Pressure

Shut-Off Valve

ipe size at

least !/2"

CONNECTING THE DRYERTO THE GAS SUPPLY(cont.)

@Install a 1/8" NPT plugged tapping to the dryer

gas line shut-off valve for checking gas inlet pressure.

Install a flare union adapter to the plugged

tapping.

NOTE: Apply pipe compound or PTFEtape to the threads of the adapter and plugged tapping.

oArPPITYFPitPe;°tm Pa_und_@

male threads. __ W PlaUp_1_dg

r_ Tighten all connections, using two adjustable

wrenches. Do not overtighten.

Apply pipe compound to the adapter and dryer gas inlet

r_ Tighten the flexible gas line connection, using

two adjustable wrenches.

EF1Open the gas shut-off valve.

Installation Instructions

CONNECTING A GAS DRYERIskip for electric dryers)Icont.)

TEST FOR LEAKS

Never use an open flame to test for gas leaks.

Check all connections for leaks with soapy solution or equivalent.

Apply a soap solution. The leak test solution must

not contain ammonia, which could cause damage

to the brass fittings.

If leaks are found, close the valve, retighten the

joint and repeat the soap test.

Open Gos

ELECTRICAL CONNECTION INFORMATION FOR GAS DRYERS {cont.}

The dryer must be electrically grounded in

accordance with local codes, or in the absence of local codes, with the National Electrical Code, ANSI/

NFPA 70 or Canadian Electrical Code, CSA C22.1

This appliance must be supplied with 120V, 60Hz,

and be connected to a properly grounded branch circuit protected by a 15 or 20 amp circuit breaker or time delay fuse. If electrical supply provided does not meet these requirements, it is the owner's responsibility to have a licensed electrician install a properly grounded 3-prong outlet.

Ensure proper ground exists

before use.

ELECTRICAL CONNECTION INFORMATION FOR GAS DRYERS

_,dL

_ - Electrical Shock Hazard

Plug into a grounded 3 prong outlet. DO NOT remove ground prong.

DO NOT use an adapter. DO NOT use an extension cord.

Failure to do so can result in death, fire or electrical

shock.

If local codes permit an external ground wire (not provided) may be added by attaching to the green ground screw on the rear of the dryer, and

to a grounded metal cold water pipe or other

established ground.

Ground Screw

Instollotion Instructions

CONNECTING AN ELECTRIC DRYER

(Skip for gos dryers ond if your dryer olreody hos o power cord ottoched)

TOOLS YOU WILL NEED

OSlip-joint pliers 0 Phillips screwdriver

0 Flat-blade crewdriver 0 Level

MATERIALS YOU WILL NEED

04" dia. metal elbow

03/4" strain relief

IUL recognized)

OGIoves

O Exhaust hood

Before making the electrical connection, turn off the circuit breaker(s) or remove the dryer's circuit fuse(s) at the electrical box. Be sure the dryer cord

is unplugged from the wall. NEVER LEAVE THE ACCESS COVER OFF THE TERMINAL BLOCK.

O4" duct

clamps (2)or 4" spring clamps (2)

0 Safety glasses

04" dia. metal duct

(recommended)

O4" dia., UL-listed

flexible metal duct

(if needed)

0 Duct tape

O Dryer power cord kit

(not provided with dryer)

)

UL rated 120/240V, 30A with 3 or 4 prongs.

Identify the plug type as per the house receptacle before purchasing line cord.

O4" Cover Plate (Kit

WE1H454)

InstallationInstructions

CONNECTING AN ELECTRIC DRYER {cont.}

{Skipforgas dryersand ifyour dryeralreadyhas a power cord attached}

ELECTRICAL CONNECTION INFORMATION FOR ELECTRIC DRYERS

For electrical connections using a power cord:

- Fire Hazard

Use a new UL-listed 240V 30 amp dryer power supply

cord with closed ring terminals or spade terminals with

upturned ends. Use a UL-listed strain relief.

Disconnect power before making electrical

connections. Connect neutral wire (white or center wire) to center

terminal. Ground wire (green or bare wire) must be connected to

green ground connector. Connect remaining two supply wires to remaining two

terminals. Securely tighten all electrical connections.

Replace the terminal block cover. Failure to do so can result in death, fire or electrical

shock.

GROUNDING INSTRUCTIONS

For a grounded, cord-connected dryer: This dryer

must be grounded. In the event of a malfunction or breakdown, grounding will reduce the risk of electric shock by providing a path of least

resistance for electric current. This dryer uses a cord having an equipment-grounding conductor and a grounding plug. The plug must be plugged

into an appropriate outlet that is properly installed and grounded in accordance with all local codes

and ordinances.

Improper connection of the

equipment-grounding conductor

can result in a risk of electrical shock. Check with a qualified electrician, or service representative or

personnel, if you are in doubt as to whether the appliance is properly grounded. DO NOT modify the

plug on the power supply cord. If it will not fit the outlet, have a proper outlet installed by a qualified

electrician. SAVE THESE INSTRUCTIONS

ELECTRICAL CONNECTION INFORMATION FOR ELECTRIC DRYERS

For direct wire connections:

- Fire Hazard

Use 10 gauge copper wire. Use a UL-Jisted strain relief.

Disconnect power before making electrical connections.

Connect neutral wire (white or center wire) to center terminal.

Ground wire (green or bare wire) must be connected to green ground connector.

Connect remaining two supply wires to remaining two terminals.

Securely tighten all electrical connections. Replace the terminal block cover.

Failure to do so can result in death, fire or electrical shock.

GROUNDING INSTRUCTIONS

For a permanently connected dryer: This dryer must be connected to a grounded metal,

permanent wiring system, or an equipment- grounding conductor must be run with the circuit

conductors and connected to the equipment- grounding terminal on the appliance.

Improper connection of the equipment-grounding conductor

can result in a risk of electrical shock. Check with a qualified electrician, or service representative or

personnel, if you are in doubt as to whether the appliance is properly grounded. SAVETHESEINSTRUCTIONS

Installation Instructions

CONNECTING DRYER USING 4-WIRE

CONNECTION (MUST BE USED FOR

MOBILE HOME INSTALLATION)

NOTE:Since January !, !996, the National Electrical Code requires that new constructions use a q-wire connection to an electric dryer. A q-wire cord must also be used where local codes do not permit grounding through the neutral.

3-wire connection is NOTfor use on new construction.

Remove ground strap Hot Relocate and discard, Keep Wire green

greengroundscrew

here

Fuse

Cover

4 #10 AWG minimum copper conductors or 120/240V 50A power supply cord kit marked for use with dryers and provided with closed loop or spade terminals with upturned ends (not supplied).

1. Turn off the circuit breaker(s) (:SOamp) or remove the

dryer's circuit fuse at the electrical box.

2. Be sure the dryer cord is unplugged from the wall

receptacle.

3. Removethe power cord cover located at the lower back.

4. Remove and discard ground strap. Keep the green ground screw for Step 7.

5. Install 3/4 in. UL-recognized strain relief to power cord entry hole. Bring power cord through strain relief.

6. Connect power cord as follows: A. Connect the 2 hot lines to the outer screws of the

terminal block (marked L1and L2).

B.Connect the neutral (white) line to the center of the

terminal block (marked N).

7. Attach ground wire of power cord with the green ground screw (hole above strain relief bracket). Tighten all terminal block screws (3)securely.

8. Properly secure power cord to strain relief.

9. Reinstall the cover. NEVER LEAVE THE COVER OFF OF THE TERMINAL

BLOCK.

Strain 3/4" UL Relief Recognized

Bracket Strain Relief

CONNECTING DRYER USING 3-WIRE CONNECTION

If required, by local code, install external ground (not provided) to grounded metal, cold water pipe, or other established ground determined by a qualified electrician.

Hot

Wire

Green Ground Screw & Ground Strap

]

Fuse

Cover

] #10 AWG minimum copper conductors or 120/240V ]OA power supply cord kit marked for use with dryers and provided with closed loop or spade terminals with upturned ends (not supplied).

3-wire Connection Not for use in Canada. DONOT use for Mobile Home Installations. NOTfor use on new construction. NOTfor use on recreational vehicles.

NOTfor use in areas where local codes prohibit grounding through the neutral conduction.

1. Turn off the circuit breaker(s) (30 amp) or remove the dryer's circuit fuse at the electrical box.

2. Besure the dryer cord is unplugged from the wall receptacle.

3. Remove the power cord cover located at the lower back.

4. Install 3/a-in. UL-recognized strain relief to power cord entry hole. Bring power cord through strain

relief.

5. Connect power cord as follows: A. Connect the 2 hot lines to the outer screws of the

terminal block (marked L1and L2).

B.Connect the neutral (white) line to the center of the

terminal block (marked N).

6. Besure ground strap is connected to neutral (center) terminal of block and to green ground screw on cabinet rear. Tighten all terminal block screws (3) securely.

7. Properly secure power cord to strain relief.

8. Reinstall the cover.

Strain 3/4" UL Relief Recognized

Bracket StrainRelief

NEVER LEAVE THE COVER OFF OF THE TERMINAL BLOCK.

Installation Instructions

EXHAUSTING THE DRYER

- Fire Hazard

This dryer MUST be vented to the outdoors.

Use only 4" rigid metal ducting for the home exhaust vent.

Use only 4" rigid metal or UL-LISTEDtransition duct

to connect the dryer to the home exhaust duct.

DO NOT use a plastic vent. DO NOT exhaust into a chimney, kitchen exhaust,

gas vent, wall, ceiling, attic, crawl space, or concealed space of a building.

DO NOT install a screen in or over the exhaust duct. DO NOT use duct longer than specified in the

exhaust length table. Failure to follow these instructions can result in

death or fire.

TOOLS AND MATERIALS YOU WILL

NEED TO INSTALL EXHAUST DUCT

C1Phillips-head

screwdriver

17Duct tape or

duct clamp

17Rigid or UL-listed

flexible metal 4" (10.2 cm) duct

17Drill with 1/8" drill bit

(for bottom venting)

C1Hacksaw

17Vent hood

PARTS AVAILABLE FROM LOCAL SERVICE ORGANIZATIONS

• Rigid Metal Duct Components WXSX63 4 x 1 Duct

WX8X64 4 x 2 Duct WX8XS1 4 Elbow

WX8×S9 4 Aluminum Hood Flexible Metal Duct Components

W×8XS8 4 Clamps (2) WX8×59 4 Aluminum Hood

WX08×::[0077 6 UL-Listed, Flexible Metal (Semi-Rigid)

Duct, 2 Clamps, 2 Close Elbows

WE1H454 Cover rear exhaust opening

CONNECTING THE DRYER TO HOUSE

VENT

RIGID METALTRANSITIONDUCT

Forbest drying performance, a rigid metal transition

duct isrecommended.

Rigidmetal transition ducts reduce the risk of crushing

and kinking.

UL-LISTEDFLEXIBLEMETAL CLOTHESDRYER

TRANSITIONDUCT

If rigid metal cannot be used, then UL-LISTEDflexible metal clothes dryer transition duct (GEparts -

PIO8XlO085, WXO8XlO085 or WXO8XlO077) can be used.

• Never install transition duct in walls, ceilings,floors or other enclosed spaces.

Total length of transition duct should not exceed 8' (2.4 m).

Formany applications, installing elbows at both

the dryer and the wall is highly recommended (see

illustrations at right). Elbows allow the dryer to sit close to the wall without kinking and/or crushing the transition duct, maximizing drying performance.

Avoid resting the duct on sharp objects.

UL-LISTEDFLEXIBLEMETAL (FOIL-TYPE)TRANSITION DUCT

• Inspecial installations, it may be necessary to connect the dryer to the home exhaust vent using flexible metal (foil-type) transition duct. UL-LISTEDuniversal flexible dryer transition duct (GEparts - PM8X73or WX8X73)

may be used ONLYin installations where rigid metal or flexible metal transition ducting cannot be used AND where a 4" diameter can be maintained throughout the entire length of the transition duct.

InCanadaandthe UnitedStates,onlytransition ductsthat

comply with "UL2158ASTANDARDFORCLOTHESDRYER

TRANSITIONDUCT"shall be used.

Avoid resting the duct on sharp objects.

Forbest drying performance:

1.Slide one end of the duct over the clothes dryer outlet pipe.

2.Secure the duct with aclamp.

]. With the dryer in its permanent position, extend

the duct to its full length. Allow 2" of duct to overlap the exhaust pipe. Cut off and remove excess duct. Keep the duct as straight as possible for maximum airflow.

4.Secure the duct to the exhaust pipe with the other clamp.

+ 28 hidden pages