GE GTx Installation Guide
BEFORE YOU BEGIN
Read these instructions completely and
carefully.
Prepare Electrical Wiring
Electrical Requirements
Do not perform mask installation in
wet locations
Follow all National Electric Codes
(NEC) and local codes.
Step 1
Step 2
Removal of internal
lens will void your
warranty
Step 6
Step 6
Mask
locating
feature
Align the locating
features on the
mask & back
housing
Instructions for
Single Piece
Masks
Step 3
Step 4
Back housing
locating
feature
Cushioned
surface
Installation Instructions
TM
GTx
IMPORTANT NOTICE: "Removal of the internal domed lens will void your warranty."
Always WEAR gloves.
DO NOT touch the front shell or internal domed lens at ANY TIME without gloves.
ALWAYS Rest the front shell on something soft, to prevent scratching.
Avoid dropping or leaving any debris in the lamp when it is open.
Failure to properly follow these instructions may cause the signal to malfunction.
Mask Installation Steps:
LED Traffic Signal Internal Masks
200mm (8in) and 300mm (12in) Circular Modules
1. Remove gasket: Pull the gasket up and out.
2. Turn lamp over: Lay the front shell on a cushioned surface to avoid scratching or damaging the surface.
3. Unclip lamp: Insert a thin flathead screwdriver slightly to one side of a clip and pry it outward. Repeat until all
8 clips are undone.
4. Remove front shell: Place the lamp on its back housing and locate the back housing locating feature.
5. For single piece masks proceed to step 6. For two-piece arrow masks go to step 7.
6. Align mask: Align the locating features on the mask and back housing, and place the mask on the back
housing. The mask will not rotate if the locating features are aligned correctly. Proceed to step 8.
NOTE: If you prefer to have this Installation Instructions document in
other languages, visit our official website at:
www.gelighting.com/installation
Step 7a
Step 7a
Step 8
Step 8
Step 9:
Clipped
Installation Instructions (cont’d)
GTx
TM
LED Traffic Signal Internal Masks
Shell
locating
Feature
Click!!
OK!
16 equally
spaced
locating
features
Step 7b
Step 7b
Step 10:
Squeeze flange
Not
clipped!
Instructions for
Two Piece
Arrow Masks
Crown locating
feature: at the
center of the
narrow side
Align the
locating
features on the
mask (Arrow) &
crown
Align the
locating
features on
the crown &
back housing
GE Lighting Solutions • 1-888-MY-GE-LED • www.gelightingsolutions.com
1 - 8 8 8 - 6 9 - 4 3 - 5 3 3 • or • +1.216.266.2419
GE Lighting Solutions, LLC is a subsidiary of the General Electric Company. GTx is a trademark of GE Lighting Solutions, LLC. The GE brand and logo are trademarks of the
General Electric Company. © 2012 GE Lighting Solutions, LLC. Information provided is subject to change without notice. All values are design or typical values when
measured under laboratory conditions.
TRAF203-R130816
7. For two-piece arrow masks which consist of:
the crown (the hollow circular plastic part)
the arrow mask (the directional arrow which fits on top of the crown)
a. Orient Crown: Align the locating features on the crown and back housing. Place the crown on the back
housing. The crown will not rotate if the locating features are aligned correctly.
b. Orient arrow mask: Align the locating features on the mask (Arrow) and crown. There are 16 locating
features to give orientation options for different directions. Once the appropriate direction is selected
place the mask (Arrow) on top of the crown. The mask (Arrow) will not rotate if the locating features are
aligned correctly.
8. Close lamp: Clip the front shell onto the back housing by aligning the locating features at the top of the back
housing and the top of the shell, then squeeze the two together at each clip until you hear a click.
9. Verify sealing: Turn the lamp upside down to check that all 8 clips are engaged.
10. Ensure proper sealing: Squeeze the flange between the clips to completely seal the lamp.
11. Reinstall the gasket (refer to Step 1).
This product is intended solely for the use of traffic signaling and is not intended for use in any other applications
Loading...