GE PTS25SHSARSS, PTS25SHRCRBS, PTS25SHPARBS, PTS25LHSARWW, PTS25LHSARCC Owner’s Manual

...

vvvvw.GEAppliances.com

Safety Instn_ions

Adapter Plugs .................... 3

(?onnect Electficiw ................ 3

Extension Cords .................. 2

Proper Disposal ................... 2

Safetv Precautions ................. 2

Operating Instru_Ttions

Additional Features ................ 9

Aurora atic Icemaker . ............. ] 0

(kgntrols ...................... 4, 5

Crispers and Pans .............. 9, 10

Sheh'es and Bins ................ 7, 8

VVamr Dispenser ................. 11

_4'ater Filter ...................... 6

Models 22,25

Cong_lateur sup&'ieur

Rdfrigdrateurs

La section frangaise commence a la page 31

Care and Cleaning .............. 11

Replacing the Light Bulbs ......... 12

Installation Instrut_tions

Preparing to Install

the Refrigerator .................. 13

Reversing the Door Swing ...... 18-22

_'amr Line Installation ......... 14--18

Troubleshooting Tips ......... 24-26

Nomml Operating Sounds ......... 23

Consumer Support

Consumer Support ........ Back Co_r

Performance Data Sheet ........... 27

Stare of Calitbmia _4"ater

Treammnt Device Certificam ....... 28

_4'anantv for Canadian Customers ...29

VVanantv tbr U.S. Customers ....... 30

Congelador superior

Refrigeradores

La secci6n en espa#ol empieza en la pagina 63

Write the model and serial numbers here:

Model #

Serial #

Find these nmnbers on the gray label

on the lett side, near the top of the refl'igera tot compartment.

200D2463PO07 49-60338 09-04 JR

IMPORTANTSAFETYINFORMATION. READALLINSTRUCTIONSBEFOREUSING.

WARNING!

Use this appliance only for its intended purpose as described in this Owner's Manual

SAFETYPRECAUtiONS

When using electrical appliances, basic safety precautions should be followed, including the following:

This refrigerator must be i)roperl,v installed and located in accordance with tile Installation

Instructions betore it is used.

Do not allow children to dimb, stand or hang on tile shelves in tile retiJgeratm: They could

damage the refl_igerator and seriously iqim'e themselves.

Do not touch tile cold sm'fi_ces in tile fl'eezer compartment when hands are damp or wet.

Skin mm stick to these extremely caM surii_ces.

Do not store or use gasoline or other flammable

\'ape,s and liquids in tile vicinity of this or any

other appliance.

In refl_igerato_s with automatic icemake_, avoid contact with tile moving parts of tile

ejector mechanism, or with the heating element located on the bottom at the icemaker

Do not place finge_ or hands on tile autolnatic icemaking mechanism while tile reii_igerator

is plugged in.

Keep finge_s out of tile "pinch point" areas; clearances between the (lom_ and between

the doo_ and cabinet are necessarily small. Be careflfl closing doo_s when children are

in the area.

Uni)lug tile refrigerator beliwe cleaning and making _ei)ai_s.

NOTE: We stronglyrecommend that any servicingbe

performedbyaquafif/edindividual

Setting tile controls to tile 0 (Off) position does not remove power to the light drcuit. On some

models, only the refl_igerator control has a

0 (off) setting.

Do not reti'eeze fl'ozen fi_ods which have thawed completely:

A DANGER!RISKOFCHILDENTRAPMENT

PROPERDISPOSALOFTHEREFRIGERATOR

Child entrapment and suffocation are not

problems of tile past. Jtmked or abandoned

reffigerato_ are still dangerous...even if they

will sit tar "just a tew da):s." If you are getting

rid of yam" old refrigerato_; please tallow tile

instructions below to hel I) prevent accidents.

Before YouThrowAway YourOld RefrigeratororFreezer:

Take off tile dom_.

I,ea_e tile shelxes in place so that children

mm not easilx climb inside.

Refrigerants

M1 refl-igeration products contain reli_igerants, which under fi_deral law must be removed prior

to product disposal. If you are getting rid of an old reli_igeration product, check with tile company

handling tile disposal about what to do.

USEOFEXTENSIONCORDS

Because of potential safety hazards under certain conditions, we strongly recommend against the use of an extension cord.

HoweveI; if vet! IllllSt use }111extension cord, it is absohltely necessary that it be a UL-listed (in tile United Stares) or a CSA-listed (in Canada), 3-wire grounding type appliance extension cord having a gromMing

type plug and outlet and that tile electrical rating _ff tile cord be 15 amperes (minimmn) and 120 volts.

vvvvw.GEAppliances.com

a, WARNING!

HOWTOCONNECTELECTRICITY

Donot, under any circumstances, cut or remove the third (ground) prong from the power cord. For

personal safety this appliance must be properly grounded.

The power cord of this appliance is equipped

with a 3-prong (grounding) plug which mates with a standard 3-prong (grounding) wall outlet

to minimize the possibili F of electric shock hazard fl'om this appliance.

Have the wall outlet and ci_vuit checked bv a qualified electt{cian to make sure the outlet

is properly grounded. If the outlet is a standard 2-prong outlet,

it is your i)e_onal responsibilib' and obligation to have it replaced with a properly grounded

3-prong wall outlet.

The refl-igerator should always be plugged into its own individual electrical outlet which has

a voltage rating that matches the rating plate.

This provides the best perlkmnance and also prevents overloading house wiring circuits which

could cause a fire hazard fl'om overheated wires.

Never tml)lug your refl'igerator b)' pulling on the

power cord. Mwa):s grip plug firefly and pull

straight out from the outlet.

Rel)air or replace immediately all power cords that have become fl'aved or otherwise damaged.

Do not use a cord that shows cracks or abI'asion damage along its length or at either end.

_._]_en moving the refi_igerator away ti'om the wall, be careflfl not to roll over or damage the

power cord,

USEOFADAPTERPLUGS(Adapterplug notpermittedincanada)

Because of potential safety hazards under certain conditions, we strongly recommend against the use of an adapter plug.

However; if win, must use an adapter; where local codes pemfit, a temporary connection may be made

to a properly grounded 2-prong wall outlet b)' use of a UIAisted adapter available at most local

hardware stores.

The linger slot in the adapter must be aligned Mth the larger slot in the wall outlet to provide proper

polarity in the connection of the power cord.

When disconnecting the power cord fl'om the

a(lapte_; always hold the adal)ter in place with one hand while pulling the power cord plug with the

other hand. If this is not done, the adapter ground temfinal is ve_' likely to break with repeated use.

If the adapter ground temfinal brealcs, DO NOT USE the refl'igerator until a proper ground has been

established.

Attachk_gtheadaptergroundterminaltoa wall outlet coverscrewdoesnotgroundtheapphanceunlessthe

coverscrewis metal,andnot insulated,andthewall outer isgroundedthroughthehousewiring. Youshould

havethe circuitcheckedbyaquafifiedelectriciantomake suretheoutlet isproperlygrounded.

READANDFOLLOWTHISSAFETYINFORMATIONCAREFULLY.

SAVETHESEINSTRUCTIONS

Aboutthe controlsontherefrigerator.

Thecontrols will look like one of the following:

(

Initially, set the refrigerator control at5 and the freezer control at 5 and allow 12-24hours for the temperature to stabilize.

Several adjustments may be required. Adjust the controls one

increment at a time, and allow 12hours after each adjustment for

the refrigerator to reach the temperature you have set. Setting the controls to # stops cooling in both the refrigerator and

freezer compartments but does not shut off electrical power to the refrigerator. Onsome models, only the refrigerator control has a #setting.

Touchpad controls

* Setting either control at 0 will automatically set the other control at O.

Thezeros will blink until you set the controls.

* If both controls are set at 0 and either COLDERpad is pressed, the

controls will automatically reset to 5.

Controlsettingswill varybasedon personalpreferences, usageand

operatingconditions andmay require more than oneadjustment.

Locking the Controls (onsomemodels)

This teature allows you to lock the (ontrols so the settings cannot be changed.

Tolock the controls:

O Set the controls to the desired settings.

@ Press and hold the lock pad tot

3 seconds.

\._l_en the controls are locked, the indicator light will come on and the control settings will not be displayed.

Tounlock the controls:

Press and hold the lock pad fin" 3 seconds. ?dter unlocking the controls, the settings

will be displayed, the lock indicator light will go out and the settings can be changed.

Aboutthe temperaturecontrols, www.GEAppliances.com

The temperature controls are preset in the factory at 37°F for the refrigerator compartment and O°Ffor the freezer compartment. Allow24 hours for the temperature to stabilize to the preset recommended settings.

The temperature controls can display both the SET temperature

as well as the actual temperature in the refrigerator and freezer.

The actual temperature may vary slightly from the SET

temperature based on usage and operating environment.

Setting either or both controls to OFFstops cooling in both the

freezer and refrigerator compartments, but does not shut off

electrical power to the refrigerator. NOTE: The refrigerator is shipped with protective film covering

the temperature controls. If this film was not removed during installation, remove it now.

Tochange the temperature, press and release the

WARMER or COLDERpad. Tile SETlight will come

on and tile display will show tile set temi)eramre. To change the temperature, tap either the

WARMER or COLDERpad until tile desired

telni)erature is displayed. Refl_gei'ator telni)eratures

can be a(!justed between 34°F and 44°F and tile fl'eezer teinperatures can be ac!justed between

-6°F and +6°E

Once the desired temperature has been set, the temperature display will return to the actual

refl_gerator and fl'eezer teinperatures after 5 seconds. Several ac!jusnnents may be required.

Each fiine yotl a(!]/lSt controls, allow 24 ho/llN tk)i"tile refl_gerator to reach tile temperatm'e you have set.

Locking the Controls (onsomemodels)

This feature allo_vs you to lock tile controls so the settings cmmot be changed.

Tolock the controls:

0 Set tile controls to tile desired settings.

Press and hold tile lock pad fi)r 3 seconds.

When tile controls are locked, tile indicator

light will come on and tile control settings

will not be displayed.

Toturn the cooling system off, tap tile WARMER pad

fin" either tile refl_gerator or tile fl'eezer tmtil tile

display sho_vs OFF Toturn the unit back on,press tile

COLDERpad fin" either tile refrigerator or fl'eezex:

The SETlight will illuminate on the side w)u selected. Then press the COLDERpad again (on the

side where the S_"Tlight is illuminated) and it will go to the preset points ot O°Ftor the fl'eezer and

37°Ftor the reti_igeratox: Setting either or both controls to OFFstops cooling in both the fl'eezer

and refl_gerator compartments, but does not shut off' electrical power to tile refl_gerato_:

Tounlock the controls:

Press and hold tile lock pad fin" 3 seconds.

Mter unlocking tile controls, tile settings will be displayed, tile lock indicator light

will go out and tile settings can be changed.

Aboutthe water filter.(onsomemodels)

Water Filter Cartridge

The water filter cartridge is located inside the cartridge holder in the back upper right

corner of the reflJgerator compartment.

/VOTE:Some models ship with the filter bypass plug in place of the filter cartridge.

The filter byl)ass I_lug needs U) be removed betore the filter cartridge is installed. Keep

the filter bypass I_lug fin" flmu'e use.

When to Replace the Filter

The filter cartridge should be replaced e\'erv six months or earlier if the flow of

water to the icemaker and dispenser decreases.

Installing theFilter Cartridge

0 If }ou are replacing the cartridge,

fi_t remove the old one. To open the

cartridge cove_; push in where indicated and the cover will drop down.

@ Remoxe the cartridge b) slowl) rotating

it to the left. A small amomlt of water

may drip down.

Filter BypassPlug

Y)u must use the filter b)pass plug

when a replacement filter cartridge is not available. The dispenser and the icemaker

will not operate without the filter or filter bypass plug.

Replacement Filters

Toorderadditionalfilter cartridges

in theUnitedStates,visitourWebsite,

www.GEAppliances.com,orcall GEPartsandAccessories,800.626.2002.

Filter Model (;S_4'F Suggested Retail Price $34.95 USD

CtlStOlllei_ in Canada should constllt tile yellow pages fin" the nearest Camco

Service Center:

CAUTION_ If air has been

trapped in the system, the filter cartridge may be ejected as it is remoxed. Use caution

when i'eiilo_,in r

O Mark yore" calendar to remind you to

replace the filter cartridge in sixmonths.

0 Remove the protective foil fl'om the end

of the cartridge.

Position the cartridge inside the

cartridge holder and slowl) rotate the

cartridge to the right tmfil it stops. _]_en the cartridge is properly installed,

vou will feel it "click" as it locks into place. The blade on the end of the

cartridge should be positioned

xertically: Do not overtighten.

O Close the cartridge cove_;

@Rtm water fl'om the dispenser fin.

3 minutes (about 1½ gallons) to clear

tile system and prevent sputtering. See To Use the l)isponser section.

NOTE:A newlxqnstalled water filter cartridge may cause water to spurt flom the dispensex:

Abouttheshelvesandbins. vvww.GEAppliances.com

Not all features are on all models.

Rearranging the Shelves

Shel',es in the refi-igerator and fl'eezer (On_l)artments are a(!iustnble.

Refrigerator Compartment

Toremove:

0 i 0

Some models have wire shelves that can be adjusted in the same mamTer.

ii i i

0 Tilt the shelf up at the fl'ont.

I,ift the shelf u I) at the back and

bring the shelf out.

To replace:

0 _'_hile tilting the shelf up, insert the top

hook at the back of the shelf in a slot

on the track.

I,ower the fi'ont of the shelf tmtil the

bottom of the shelf locks into place.

Freezer Compartment

Toremove:

I,ifl up the left side of the shelf and

slide it left into the center of the shelf

SUl)l)OXlS.

0 Rotnte the right side of the shelf up and

out of the shelf sui)ports.

Toreplace:

0 Holding the shelf diagonall}_ insert the

left end of the shelf into the center of

the shelf SUl)poxls on the side wall at the desired level.

Insert the right end of the shelf into the

shelf supports at the same level. Rest

each end of the shelf on the bottom of the shelf suI)ports,

Spillproof Shelves (onsomemodels)

SI)illproof shelves have sl)e(ial edges to hel I) prexent spills fi'om dripl)ing to lower

shelves. To remme or replace the shelves,

seeRearrangingtheShelves.

NOTE."Formodelswith an automatic icemaker,

the freezershelf must be in thelower position fortheicecube buckettocatch the cubes.

Abouttheshelvesandbins (cont.).

Sfide-Out Spil/proof Shelf (onsomemodels)

The slide-out spilli)roof shelf allows )ou Toreplace: to reach items stored behind othe_. The

special edges are designed to help prexent 0 Place the rear shelf tabs just in fl'ont of spills from dripping to lower shelxes.

To remove: _ Slide the shelf in until the central tabs

0 I,iJt the fl'ont edge ot the shelf until the

0 ())nfinue pulling the shelf fi)r_n'd

' ' the central notches on the shelf frame.

Remove all items fl'om shelfl

Slide the shelf out tmfil it stops.

central tabs are above the fl'ont l)a_;

until it can be removed.

are slightly behind the front l)a_;

I,ower the sheff into place tmtil it is

horizontal and slide the shelf in.

Make sure that the shelf sits fiat after relbsta//at/on anddoesn'tmove freely fromside to side.

Make sure youpush theshelvesall the wayin before youclose the door

,Fingerhold

,,Snugger

Adjustable Bins on the Door

A(!iustable bins can easily be carried fi'om

I'etiJgeI':ltoI" to woYk _lI'e_l,

To remove: i,ifi bin straight ui), then

pull out.

To replace or relocate: Engage the bin in the

molded supports of the (loox; and push in. Bin will lock in place.

Non-Adjustable Shelves on the Door

To remove: Lift the shelf straight up, then

pull out.

To replace:Engage the shelf in the molded

SUl)l)orts on the door and push down.

It will lock in place.

Freezer Tilt Out Bin (onsomemodels)

Push the button as you tilt out the bin.

Toremove: Hold the sides of the bin and

lift it straight uI), then ptfll out.

To replace:Engage the ends oI the bin in

the molded SUpl)orts on the door and

push down. It will lock in place.

NOTE."Do not overload the b/n.

The snuggerhelps prevent tipping, spilling

or sliding of small items stored on the door shelf. (h_iI) the finger hold near the rear of

the snugger and move it to fit w)ur needs,

Abouttheadditional features, vvww.GEAppliances.com

Not all features are on all models.

Shelf Saver Rack (onsomemodels)

Slide-out beverage rack holds 19 cans of soda (it _2_m_e/water" bottles (lengthwise).

It can be remoxed fin" cleaning.

Aboutthe crispersandpans.

Not all features are on all models.

Fruit and Vegetable Crisper

Excess water that may accumulate in tile

bottom of tile drawei_ or under tile drawei_

should be wiped dry.

Toremove, slkle the rack out to the stop

position, lift the rack up and past the stop

position and lift it out.

:!!

Adjustable Humidity Crisper (onsomemodels)

Slide tile control all tile way to tile Slide tile control all tile way to tile LOW

HIGHsetting to provide high humidit_ setting to l)rovide lower h umidit} levels recommended for most vegetables, recommended fin" most fl'uits.

Snack Pan (onsomemodels)

This pan can be moxed to tile most useflll location fi)r _our family's needs.

Toremove, slide tile pan ()lit to tile stop

position, lift tile pan up and past tile stop position and lift it ()lit.

Adjustable Temperature Deft Pan (onsomemodels)

When tile pan is placed in the top 6 slots

on the left side and the lever is set at COLDEST,air fl'Oln tile ti'eezer is fi)rced

arotlnd tile pan to kee I) it veI_' cold.

You can move the pan to any location if you don't want tile extra cold storage.

Tile settings can be a(!justed anywhere between cold , and coldest _ *.

When set at cold, the pan will stny at the

nomml reflJgerator temperature.

The coldest setting provides the coldest storage _1i'e_l.

Aboutcrisperremoval

Not all features are on all models.

Crisper Removal

To Remove:

These drawex5 can be remoxed easily b) lifting up slighfl) while pulling the drawer

past the stop location.

Abouttheautomaticicemaker.

When the door cannot be fully opened,

rein eve the dra wet fi_rth est fl'om the door fixst. Make sure the drawer closest to the

door is fifllv closed. There is a latch at the front of the center slide rail. Push down on

the latch and slide the center slide rail, to

which the drawer is attached, a_;ly fl'om the

door Renlove the drawer

A newly-installed refrigerator may take 12-24 hours to begin making ice.

Power

Switch Icemaker

Automatic Icemaker (on some models)

The icemaker will produce seven or eight cubes (depending on model) per cycle--

appro_mately 100-130 cubes in a 94-hem-

period, depending on fl'eezer compartment teiilpei'attli'e_ i'ooi/] teiilpei'attli'e_ ntlillber

of door openings and other use conditions.

PowerLight

Powerswitch model

erArm

There are two t)pes oficemake_s: power switch models and ti_eler am/models.

If the refi-igerator is operated heft)re the water connection is made to the icemake_,

set the power switch U) 0 (Off) or move the teeler am_ to the STOP(up) position.

When the refl-igerator has been connected to the water sui)i)ly, set the power switch to

the I (on)position or move the teeler am/to the ON (down) position. On power switch

models, the green light will come on.

Fee!erArmin (up)position

theON (down)

position

Feelerarm model

You will hear a buzzing sotmd each dine

the icemaker fills with water;

The icemaker will fill Mth water when it

cools to approximately 15°F. A newly-

installed refrigerator may take 12 to 24

houI_ to begin making ice cubes.

Throw awm the first tow batches of ice to allow the water line to clear

Be sm'e nothing intetTeres xfith the sweep of the feeler amL

_._]_en the bin fills to the level of the teeler am_, the icemaker will stop producing ice.

It is nomml fin" several cubes to be.joined together:

If ice is not used fl'equentl> old ice cubes will become cloud> tnste stnle and shrink.

On power switch models, the green power light will blink if ice cubes get stuck in the

icemaket: To correct this, set the power switch to 0 (off) and remove the cubes. Set

the power switch to ! (on) to restart the icemake_: _Mter the icemaker has been

turned on again, there will be a delay of

about 45 minutes before the icemaker I'eStlllleS opeI_ltion.

NOTE:Inhomeswithlower-than-averagewater

pressure,youmayheartheicemakercyclemultiple

timeswhenmakingonebatchofice.

Icemaker Accessory Kit

If }our refrigerator did not come ah'eadv equil)ped with an automatic icemake_;

an icemaker accessma' kit is ax filable at

extra cost.

Check the back of the refrigerator fin" the specific icemaker kit needed fin.

VOIII" model.

Aboutthe water dispenser.(onsomemodels) www.GEAppliances.com

Tile water dispenser is located on tile left

wall inside tile reti_gerator coillpartl/lent.

To dispense water:

O Hold tile glass against tile recess,

O Push tile water dispenser button,

O Hold tile glass underneath tile

dispenser fi)r 9-3 seconds aiier

releasing tile dispenser button, X_'Ker may continue to dispense

atier tile button is released.

Careand cleaning ofthe refrigerator.

Cleaning the Outside

The doorhandles and trim. Clean with

a cloth daml)ened with soapy watei: DIT with a soft cloth.

Keep the outside clean. X_]I)e with a clean cloth lightly danq)ened with miM liquid dish detergent. DIT with a clean, soil cloth.

Cleaning the Inside

If no water is dispensedwhen the refrigerator is fkst installed, theremay be alYinthe water linesystem.

Pressthe dlspenserbutton for at /east 2 minutes to removetrappedair fromthe water lineand tofill the

watersystem. Duringthis process,the dispenser

noise maybe loud asthe air is purged from the

water line system.Toflushout impurities in the water line, throw away the fkst 6 glassfuls of water

NOTE: Toavoid water deposits, the &spenser should be cleaned periodically by wiping with a clean cloth or sponge.

Do not wipe therefn)erator with a soiled dish cloth or wet towel Thesemay &avearesidue that

can erodethepain£ Donot usescouringpads, powdered cleaners,bleach orcleanerscontaining bleachbecausetheseproductscanscratchand

weakenthepaint finish.

Tohelp prevent odors, leave an open box of

baking soda in tile refl_igerator and fl'eezer

cam i)a rhll ents.

Unplugthe refrigerator before cleaning.

If this is not i)ractical, wring excess moisture ()lit of sponge or cloth when cleaning

around switches, lights or comrols. Use waml _mr and baking soda solution--

about a tablesi)oon (15 ml) of baking soda to a quart (1 liter) of wami: This both cleans

Behind the Refrigerator

Be carefifl when moving tile reii_igerator

away from tile _dl. _M1types of floor

coverings can be danmged, particularly cushioned coverings and those with

eillbossed Stli'][il ces.

Pull tile reli_igerator straight out and return

it to position by i)ushing it straight in.

Preparing for Vacation

For long Va(ations oF absen(es_ i'eillOVe

food and unplug tile refiigerator. Move

tile fl'eezer control to tile O (Off)position,

and clean tile interior with a baking soda solution of one tablesI)oon (l 5 ml) of baking soda to one quart (l liter) of wateI:

i,eave tile (looi_ open.

and neutralizes odm_. Thoroughly rinse and wipe dry:

Avoid cleaningcolflglass shelves(on somemodels)

with hot water becausethe extreme temperature difference maycausethem tobreak. Hand&glass shelvescarefully Bumping temperedg/asscan

causeit to shatter Do not wash anyrefr/_Teratorparts in the dishwasher

Washicetrays in lukewarmwater only--do notput

themin an automaticdishwasher

Moving tile reflJgerator in a side direction

may result in damage to tile floor covering

or refrigerator.

Whenpushing therefn)erator back,makesure you

don't roll over thepower cordoricemakersupply

fine{onsomemodels).

Set tile icemaker power switch to tile O (off)

position and shut off tile water supply to

tile refrigerator.

If tile temi)eramre can drop below freezing,

have a qualified seiMcer drain the water

SUl)ply system (oil some models) to prevent

serious i)roperF damage due to flooding.

Preparing to Move

Secure all loose items such as base grille, shelves and draweis by taping thenl securely in place to prevent (lamage.

Besure therefngerator staysin an up@t position duringmowbg

Replacingthe lightbulbs.

Turning the control to the 0 (off) position does not remove power to the light circuit.

Refrigerator Compartment

I il Lightshield

I[ I

CAUTION:ahtb./bsmaybehot

O Unplug the refi_igerann: O The bulbs are located at the top of

the refi_gerator coml)artn_ent near the opening. On some models, a light

shield will have to be removed.

O To remove the light shield, grasp the

shield as shown. Squeeze the shield and rotate the shield toward the back

ot the reffigeratm: The light shield

will pop out.

Freezer Compartment Light (onsomemodels)

,&CAUTION:ahtbu/bsmaybe

O/Jnl)lug the refl-igeratm:

The bulb is located behind a light

shield at the back of the fi'eezer

compartment. To remove, squeeze the top and bottom ot the shield and

pull the shield off.

O _Mter replacing with an appliance bulb

O Replace the bulb with an appliance

bulb of the salne or h_wer wattage. On models with a light shield, replace

the light shield.

O Plug the reti_igerator back in.

of the same or lower wattage, replace the shield.

Plug the refi_igerator back in.

Freezer Compartment Dome Light (onsomemodels)

A CAUTION:L>,bu/b m ybehot.

/Jnl)lug the reti-igerator

The bulb is located at the top of the

fl'eezer compartment inside the dome

light shield. To remove the shield, place your finger in the pocket at the back

ot the shield. Pull the shield fin'ward

_1II(l down.

After replacing with an appliance

bulb of the same or lower wattaoe replace the shield.

0 Plug the refrigerator back in.

Installation

Refrigerator

Instructions

Questions?Call800.GE.CARES(800.432.2737)or VisitomX_ebsite_,t:www.GEAppliances.com

BEFORE YOU BEGIN

Read these instructions completely and carefully,

• IMPORTANT - S_,,ethese

inst_ uctions fin" local inspector's use.

• IMPORTANT - Obs.,e_,ll

governing codes and ordinances.

• Note to Installer - Be sure to leave these

instructions with the Constm_er.

In Canada,call 1.800.361.3400or Visit,,mX_ebsite_,t:www.geappliances.ca

CLEARANCES

Mlow the fi_llowing clearances fin" ease of installation, proper air circulation and pluml)ing and electrical

connections:

• Sides 1/8" (4 ram)

• Top 1" (25 ram)

• Back 1" (25 ram) If the refl_igerator is against a wall on either side, allow

a 1/8" (3 Ulln) door clearance.

Models 22 and25

• Note to Consumer - KeeI) these instructions

ti,I" fllture reference.

• Skill level - Installation of this appliance requires basic mechanical skills.

• Completion time - Refrigerator Installation

15 minutes

• Proper installation is the responsibility of the installer.

• Product thihu'e due to improper installation is not covered trader the Warranty.

WATER SUPPLY TO THE ICEMAKER (ON SOME MODELS)

ROLLERS

The rollers have 3 purposes:

• Rollers at!just so the doo_s close on their own when opened about 45 °.

• Rolle_ a(!lust so the refrigerator is firefly positioned on the floor and does not wobble.

• Rollers allow ) ou to mox e the refrigerator awa) fl'om the wall fin" cleaning.

To adjust the rollers:

O Rem,,,etheb_,seg,_lleb, II I/

i,,,sitionin h mds ,sshow,,...... II

If the reli'igerator has an icemaker, it will have to be connected to a cold water line. AGE water sui)ply kit

(containing robing, shutoff wflve, fittings and

insttuctions) is available at extra cost from votu" dealer, by visiting otu" X_'ebsite at www, GF_ppliances,com (in Canada at www.geappliances.ca) or from Parts and

Accessories, 800.626.2002 (in Canada 1.888.261.3055).

REFRIGERATOR LOCATION

• Do not install the refl'igeramr where the temperature

will go below 60°F (l 6°C) because it will not run otten

enough to maintain proper temperatures.

• Do not install the refrigerator where the temi)erature will go above 100°F (37°C) because it will not i)erflwm properly.

• Install it on a floor strong enough to sui_port it fifllv loaded.

Rot;,te the bottoin of the _x.k_ _41

0 g,_lle,,._w_,_-d.n.1theclips_\ II

refrigerator: _2,_€,"

Using a screwdrixe_; turn ,,_ the two ti'ont roller

a(!justing screws clockwise to raise the refi'igeratoL

comlterclockwise to lower it.

Replace the grille so the

notch in the grille will fit

around the bottom door

hinge.

O Tilt the top of the grille

toward the refrigerator and insert the long metal clips into the top of the owfl

openings at the bottom of

the reli'igerat(n:

Rotate the bottom of the grille toward the refi'igerator

until it snaps into place.

Installation Instructions

INSTALLING THE WATER LINE CONSOMEMODELS)

BEFORE YOU BEGIN

Recommended COl)per water supply kits are WX8X2, _'_X8X3 or _,_X8X4, depending on the amom_t of tubing you need. Approved plastic water sui)ply lines are GE SmartConnect'" Refrigerator Tubing

(WX08X10002, WX08X10006, WX08X10015 and

WX08X10025). When COlmecting your refl'igerator to a GE Reverse

Oslnosis _4'ater Systeln, the only approved installation is with a GE RVKit. For other reverse osmosis water

systems, tollow the manufi_cturer's recommendations. This water line installation is not warranted by the

refrigerator or icemaker manufi_cturer. Follow these inst_ uctions carefidlv to minimize the risk of expensive water damage.

_4'ater halnlner (water banging in the pipes) in house plmnbing can cause damage to refl'igerator parts and lead to water leakage or flooding. Call a qualified plmnber to correct water hammer before installing

the water supply line to the refl'igerator. To prevent burns and product damage, do not hook

up the water line to the hot water line.

If you use your refl'igerator before cmmecting the water line, make sm'e the icemaker power switch is

in the 0 (off) position. Do not install the icemaker tubing in areas where

temperatm'es tall below freezing. When using any electrical device (such as a power

drill) during installation, be sm'e the device is double insulated or grotmded in a manner to prevent the hazard of electric shock, or is batte_ T powered.

All installations must be in accordance with local i)hunbing code requirelnents.

WHAT YOU WILL NEED

• Copper or GE SmartConnect '_'Refrigerator Tubing

kit, l/4" outer diameter to connect the reli'igerator

to the water sui)i)ly. If using COl)per, be sm'e both ends of the tubing are cut square.

To determine how much tubing you need: measure the distance fl'om the water wdve on the back of the

refl'igerator to the water sui)ply pipe. Then add 8' (2.4 m). Be sure there is sulticient extra tubing

(about 8' [2.4 m] coiled into 3 turns of about 10" [25 cm] diameter) to allow the refl'igerator to

inove out fl'om the wall after installation. GE SmartConnect'" Refl'igerator Tubing Kits are

available in the following lengths: 2' (0.6 m) - _43X08X10002 6' (1.8 m) - WX08X10006

15' (4.6 m) - WX08X10015

25' (7.6 m) - WX08X10025 Be sure that the kit w)u select allows at least 8' (2.4 m)

as described above.

NOTE: The only GE approved plastic tubing is that

supplied in GE SmartComaect '_' Refrigerator Tubing kits. Do not use any other plastic water supply line because the line is under pressure at all times. Certain

types of plastic will crack or rupture with age mad cause water dmnage to your home.

Installation Instructions

WHAT YOU WILL NEED (CONT.)

Install the shutoff valve on the nearest frequently used drinking water line.

• A GE water supply kit (containing tubing, shutoff valve and fittings listed below) is available at extra

cost frmn your dealer or fl'om Parts and Accessories,

800.626,2002.

• A cold water supply. The water pressure must be

between 2(1 and 12(1 p.s.i. (1.4-8.1 bar).

• Power drill.

• 1/2" or adjustable wrench.

• Straight and Phillips blade screwdriver.

• Two 1/4" outer diameter compression nuts and

2 ferrules (sleeves)--to connect the copper tubing to the shutoff valxe and the refrigerator water valve.

• If you are using a (;E Smalt(;onnect' Refrigerator

Tubing kit, the necessary, fittim,s_, are preassembled to the tubing

[] SHUT OFF THE MAIN WATER

SUPPLY

Ttu'n on the nearest taucet long enough to clear the line of water.

[] CHOOSE THE VALVE LOCATION

Choose a location fl_r the valve that is easily

accessible. It is best to connect into the side of a vertical water pipe. When it is necessary to connect

into a horizontal water pipe, make the connection

to the top or side, rather than at the bottom, to avoid drawing off anv sediment fl'om the

water pipe,

[] DRILL THE HOLE FOR THE VALVE

• If yotu" existing COl)per water line has a flared fitting

at the end, you will need an adapter (a\zfilable at i)lmnbing supply stores) to connect the water line to the refl'igerator OR you can cut off the flared fitting

with a tube cutter and then use a compression fitting.

Do not cut toI_nled end ti'oln GE SmartConnect '_ Refrigerator tubing.

• Shutoff valve to connect to the cold water line.

The shutoff wflve should have a water inlet with a minimmn inside diameter of 5/39" at the point of

connection to the COLD WATER LINE. Saddle-type shutoff valves are included in manv water supl)ly kits. Betore i)urchasing, inake sure a saddle-type wflve complies with yotu" local plmnbing codes.

Drill a 1/4" hole in the water pipe (even it using a sell:piercing \_flve) using a sharp bit. Remove anv burrs resulting fl'om drilling the hole in the pipe.

Take care not to allow water to drain into the drill. Faihu'e to drill a 1/4" hole may result in reduced

ice I)roduction or slnaller cubes.

Installation Instructions

INSTALLING THE WATER LINE (CONT.)

[] FASTEN THE SHUTOFF VALVE

Fasten the shutoff _al_e to the cold water pipe with tile pipe clamp.

PipeClamp_

Saddle-TypeJ -VerticalCold ShutoffValve WaterPipe

NOTE: Conmmnwealth of Massachusetts Plmnbing Codes 248CMR shall be adhered to. Saddle \_flves

are illegal and use is not permitted in Massachusetts. Consult with wmr licensed plmnber.

[]

TIGHTEN THE PIPE CLAMP

Tighten the clamp screws until the sealing washer begins to swell,

NOTE: Do not overtighten or yo/i ill[iv citlsh tile

tubing.

Pipe

Clamp

Washer

[]

CONNECT THE TUBING TO THE VALVE

Place tile compression nut and fish ule (sleeve)

fi_r COl)per tubing onto tile end of tile tubing and

connect it to the shutoff wflve.

Make sure tile tubing is flflly inserted into tile valve.

Tighten the compression nut secm'elv.

D_r plastic tubing fl'om a (kE SmartConnect ''_

Refl'igerator Tubing kit, insert tile molded end

of the tubing into the shutoff wflve and tighten

compression nut tmtil it is hand tight, then tighten

one additional turn with a wrench. Overtightening

III_IV Catlse leaks,

Saddle-Type ShutoffValve ,_

Packing Nut--

Outlet Valve-- -- Ferrule (sleeve)

NOTE: (_Ollllllonwealth of JV]assachtlsetts Phllllbing

Codes 248CMR shall be adhered to. Saddle wflves

are illegal and use is not permitted in Massachusetts.

Consult with yore" licensed plmnbe_:

3ression

Nut

SmartConnect_

Tubing

[] ROUTE THE TUBING

Route tile tubing between tile cold water line and tile refl'igera tot.

Route tile tubing through a hole drilled in tile wall or floor (behind tile refrigerator or ac!jacent base

cabinet) as close to the wall as possible.

NOTE: Be sure there is sufficient extra tubing

(about 8 feet [244 cm] coiled into 3 turns of about 10" [25 cm] diameter) to allow the refl'igerator to

move out fl'Oln tile wall after installation.

[] FLUSH OUT THE TUBING

Tm'n tile main water sui)ply on and flush out tile

tubing until tile water is clear.

Shut tile water off at tile water valve after about

one quart (l liter) of water has been flushed

through tile tubing.

Installation Instructions

[] CONNECT THE TUBING TO THE

REFRIGERATOR

NOTES:

• getm'e making tile connection to tile reti'igerator,

be sure tile refl'igerator power cord is not plugged into tile wall outlet.

• We recommend installing a water filter if w)m" water SUl)ply has sand or particles that could clog

the screen of the refl'igerator's water wdve. Install it in the water line near the refrigerator. If using

GE SmartConnect '_ Refl'igerator Tubing kit, you

will need an additional tube (WX08X10009) to

connect tile filter. Do not cut plastic tube to install filter.

Reillo'_e tile access co_,ei',

[] CONNECT THE TUBING TO THE

REFRIGERATOR (CONT.)

Fasten tile tubing into tile clamp provided to hold it in a vertical position. You may need to PU open

tile clamp. One of the illustrations below wiU look like the

connection on your refrigerator.

Icemaker Models without Water Dispenser

1/4"Tubing

)nNut

(sleeve)

SmartC_ Tubing

Water DispenserModels

TubingClamp...

- Refrigerator Connection

1/4"Tubir

Remove tile plastic flexible cap from tile water xalve

(refrigerator connection).

Place tile compression nut and ferrule (sleeve) onto the end of the tubing as shown, On GE

SmartConnect _'' Refl'igerator Tubing kit, tile nuts are ah'eadv assembled to tile tubing.

Insert tile end of tile tubing into tile water wdve connection as thr as possible. While holding the

tubing, tighten tile fitting. For plastic tubing fl'om a GE Smart(:mmect ''_

Refl'igerator Tubing kit, insert the molded end of the tubing into the shutoff \;dye and tighten

compression nut tmtil it is hand tight, then tighten one additional turn with a wrench. Overtightening

Ill'IV Catlse leaks.

1/4"CompressionNut,

Refrig

SmartConnect_ Tubing

[] TURN THE WATER ON AT THE

SHUTOFF VALVE

Tighten am connections that leak.

Reattach tile access cover.

Installation Instructions

INSTALLING THE WATER LINE (CONT.)

[] PLUG IN THE REFRIGERATOR

__rranoe the coil of tubing so that it does not xibrate

against tile back of tile refrioerator_ or against, tile wall. Push the refrigerator back to the wall.

START THE ICEMAKER

Power switch models - Set tile icemaker power switch to the I (0n) position. The icemaker will

not begin to operate tmtil it reaches its operating temperature of 15°F (-9°C) or below. It will then

begin operation automatically if the icemaker power switch is in the I (0n) position, and the

green light will come on.

Power Switch icemaker

START THE ICEMAKER (CONT.)

Feeler arm models - Move tile feeler arm to tile

ON(down) position. Tile icemaker will not begin to

operate until it reaches its operating temperature of (l 5 F) (-9 C) or below. It will begin operation

automatically if tile icemaker feeler am_ is in tile

ON (down) position.

FeelerArminthe

FeelerArmintheON (down)position

Feeler arm model

NOTE: In lower water pressure conditions, tile water xalxe IIl_l_ [t/I'II Oil II I) to . tllnes to delixer

eIlo/vrh water to the iceinakei;

STOP(up)position

3 "

Light

Power switch model

REVERSING THE DOOR SWING

IMPORTANT NOTES

When re\'e_ing tile door swing:

• Read tile instructions all tile way through before starting.

• Handle parts careflfllv to avoid scratching paint.

• Set screws down bv their related parts to aw)id using

them in the wrong places.

• Provide a non-scratching work sm'tace tot the doors.

IMPORTANT: Once vou begin, do not Inove tile

cabinet tmtil doo>swi;_g reversal is completed. These instructions are for changing the hinges fl'om

the right side to the lett side----if you ever want to change the hinges back to the right side, follow these same instHIctions and reverse all references to left and fight.

Unplug the refrigerator from its electrical outlet. Empty all door shelves, including the dairy

compartment,

TOOLS YOU WILL NEED

Phillipsscrewdriver

5/16" Headsocketdriver

3/4" Headsocketdriver

(a6-pointsocketis

recommended)

Puttyknifeor

thin-bladescrewdriver

Masking tape

Installation Instructions

[] REMOVE THE FREEZER DOOR

%q_e the door shut with nmsking tape.

Remoxe the hinge coxer on top of the fl'eezer door

(on some models).

]lemoxe the two screws, then lilt the hinge strai_*ht ui ) to fl'ee the hinge, pin fl'om the socket in the top

of the doo_:

Remove the tape and tilt the door away fl'om the cabinet, i,ifl it otf the center hinge pin.

Set the door on a non-scratching surtace with the inside up.

[] REMOVE THE REFRIGERATOR

DOOR

Tape the door shut with maskino. _ tape.

Remoxe the center hinge, I)in with a 3/4" socket.

HingePin

Remoxe the tape and tilt the door awm from the cabinet. I,ifl the door straight off the bottom hinge

bracket.

Set the door on a non-scratching sudi_ce, with the inside up.

CAUTION: Do not let door (h'o I) to the floor. To do so could damage the door stop.

[] TRANSFER TOP HINGE TO

THE LEFT

Interchange hinge and scre_vs at top fight with scrmvs

at the top left of cabinet. Do not tighten screws on hinge side at this time.

[] TRANSFER BOTTOM HINGE

BRACKET TO THE LEFT

Remove the base grille by pulling it straight out. Using a socket (hive_; move the bottom hinge bracket

fl'om the fight side to the left side.

NOTE: If the washer is not on the hinge bracket,

check to see if it is stuck to the bottom of the do(n:

Installation Instructions

REVERSING THE DOOR SWING (CONT.)

[] TRANSFER CENTER HINGE

BRACKET TO THE LEFT

]_.emove the center hinge bracket b.v removing the three screws.

NOTE: Keep these screws with the hinge bracket. They are long screws and will be used when installing

the hinge on the other side.

You will need to remove the colo>matched cap fl'om

the screw head befl)t'e volt c[lIl I'eIll(we the screw. Use the edge of a thin flat blade to gently pry the

caps off the screw heads. (A put D' knite works well fin" this.) Cover the blade with tape to prevent

scratching the paint.

Remove the mullion cover fl'om the left side using the thin flat blade. Assemble it to the fight side.

Remove the screw fl'om the center left side of the cabinet. Screw it into the holes on the right side.

Place the center hinge bracket ()vet" the holes at the center left side of the cabinet. Insert and

tighten the three hmg screws. Replace the cap by snapping it over the screw with

your finger.

[] TRANSFER REFRIGERATOR

DOOR HANDLE TO THE RIGHT

To remove the handle: Remove the I)lug button by

carefldly pr)_ng under the edge with a putt)' knife. Remove the exposed screw holding the handle.

Handle Plug

Remoxe the two screws holding the handle to the top of the door.

LongHandle

Short Screw

ShortHandle

[] TRANSFER DOOR STOPS

On each door, mo_e the metal door stoi_ ti'om the right to the left.

Moxe any screws fl'om the left to the right.

Hole Handle

\ Plug

Handle

After removing the handle: Move the small plug

buttons fl'om the top fight side of the door top and insert them into the holes on the opposite side.

SmallPlu, Buttons

Move the large, I)lu°,_ button fl'om the left edge of the door and insert it into the hole on the opposite side.

PlugButton

Installation Instructions

[] TRANSFER REFRIGERATOR DOOR

HANDLE TO THE RIGHT (CONT.)

Transfer the door I_lw"_button to the opposite side.

Butt

Reinstalling the handle: Attach the handle to the

fight side of the (loo_:

LongHandle

ShortHandle

Handle Hole

Plug

[] TRANSFER FREEZER DOOR

HANDLE TO THE RIGHT

Remo_e the screws holding the handle to the top and

bottom of the cloo_: Remoxe handle.

!x:!_g_____

"'22:22.,

Move the plug button on the right side (ff the door to the handle screw hole on the left side.

Reattach the handle on the opposite side using the holes closest to the edge of the doo_:

Installation Instructions

REVERSING THE DOOR SWING (CONT.)

[] REHANG THE REFRIGERATOR

DOOR

I,ower tile I'etl]_eKKof door onto tile bottoil/

hinge pin.

-,__%_

Straighten the door and line it up with the center hinge bracket.

Reinstall the center hinge pin with a 3/4" socket.

Turn it tmtil it extends through the hinge bracket and into the door

CenterHinge Bracket

[] REHANG THE FREEZER DOOR

I,ower the ti'eezer door onto the center hinge pin.

CenterHingePin

i,ift the top hinge so the pin fits into the door socket. Support the door on the handle side and make sure

the door is straight and the gap between the doors is even across the fl'ont. \,_]file holding the door in

place, tighten the top hinge screws.

Normal operatingsounds.

Newer refrigerators sound different from older refrigerators.

Modem refrigerators have more features and use newer

technology.

Do you hear what I hear? These sounds are normal.

HUMMM...

--WHOOSH...

• The new high efficiency compressor may run fi_ster and longer than your old refi_igerator and you may

hear a high-l)itched hum or pulsating so/md while it is operating.

• 54m may hear a whooshing so/md when the (loo_ close. This is due to pressm'e equalizing within the reti_igerato_:

Electronic models only:

• Sometimes tile refl'igerator runs for an extended period, espedally when tile doo_ are opened fl'equenfl): This

ineans that tile FrostGuardT"feature is working to prevent fl'eezer burn and improve food l)rese_wation.

CLICKS, POPS,

CRACKS and CHIRPS

• _m may hear cracking or l)Ol)ping sotmds when tile reti_igerator is fi_t l)lugged in. This hal)pens as tile

i'efiJgei'ator cools to tile coYi'ect teilll)ei'attli'e.

• Tile compressor may Catlse a clicking or chiq)ing sound when attempting to restart (this could take

uI) to 5 minutes).

• The electronic control board may cause a clicking sotmd when relays acti\me to control _efl_igerator components.

• EN)ansion and contraction of cooling coils during and

after defl'ost C_lll Catlse a ci'acking or l)Ol)ping soma&

• On models with an icemake_; after an icemaking cycle, um may hear tile ice cubes dropping into tile ice bucket.

WHIRl

54m may hear tile rims 'IS)inning.* Tile rims hel I) to

maintain tile correct temperatm'es.

Electronic models only:

• Ybu may hear tile rims spinning at high speeds. This hal)pens when tile refl_igerator is fiI_t plugged in,

when tile (loo_ are opened fl'equently or when a lmge

amotmt ot toed is added to the refl_igerator or fl'eezer

COIIll)_l i'tlilents.

• If either door is open tot over 3 minutes, you may hear the tiros come on in order to cool the light bulbs.

• Tile rims change speeds in order to provide optimal cooling and energy' savings.

WATERSOUNDS

• Tile flow of refrigerant through tile fl'eezer cooling coils may make a gmgling noise like boiling water:

• Water dropping on tile defl'ost heater can cause a sizzling, pol)ping or buzzing sotmd (lining tile

defl'ost cycle.

• A water dripping noise may occur during tile defl'ost c)'cle as ice melts fl'om tile e\_q)orator and flo_vs into

tile drain pan.

• Closing tile door may cause a gmgling sotmd due to pressm'e equalization.

• On models with a dispense_; dtwing water dispense, you

may hear tile water lines move at initial dispense and after dispenser button is released,

Beforeyoucall forservice...

Troubleshooting -tips

Save time and money/. Review the charts on the following

pages first and you may not need to call for service.

Possible Causes What ToDo

Refrigerator does not Refrigerator in defrost cycle. * Wait about 40 ufinutes for defl'ost cycle to end.

The controls axe set to * Move the reflJgerator and fl'eezer control to a

theO(o.)pos tion. )e,.,,ue

Refrigerator is unplugged. * Push the plug completely into the oudet.

The fuse is blown/cireuit * Replace fllse or reset the breaker. breaker is tripped.

Vibration orrattling Rollers need adjusting. * See Rollers.

(slight vibration is normal)

Motor operates for Normal when refrigerator * "x._fit 12-24 houx_ fin" the reti_igerator to completely long periods or cycles is first plugged in. cool down. on and offfrequently.

(Modern refrigerators Often occurs when large * This is mmna[.

with more storage placed in refrigerator.

space and a larger freezer require more Door left open. * Check to see it I)ackage, is holding door open.

operating time. They Hot weather or frequent * This is n(mnal.

staff and stop often door ope_mlgs.

tomaintain even temperatures.) Temperature controls * See About the controls.

Refrigerator or freezer Temperature control not set • See About the controls.

Frost or ice crystals Door left open. * Check to see if I)ackage, is holding door open.

on frozen food (frost within package Too frequent or too long

is normal) door ope_lhlgs.

mnotmts of food axe

set at the coldest setting.

cold enough.

Warm weather or frequent * Set the temperature control one step col([e_:

door opetm,_. See Abouttho controls.

[ , •

if )ackaoe is holding door open.Door left open. * Check to see I

Automatic icemaker lcema.ker power switch * Set the power switch to the I(on) position. (onsome models) is ha the 0 (off) position.

does not work Water supply turned off or * See Installing the water line.

not commcted. Freezer compartment * _'%fit [2-24 l_otu_ fi)r the refl_igerator to completely

too warm. cool down.

Piled up cubes h:l the storage * I,e',el cubes by hand.

bin cause the icema_ker

to shut off. Ice cubes stuck in icema_ker. * Ttlrn Off the icemake_; remoxe cubes and ttlrn the

(Green power light on icemaker back on.

icema_ker blinking.)

Frequent!'buzzing, sound

lcema_ker power switch is in the I (on) position, but the water supply

to the refrigerator has not been

commcted.

• Set the power switch to the 0 (off} position. Keelfin(*., it

in the I(OU)position will damage the water xdxe.

www.GEAppliances.com

Possible Causes What ToDo

Ice cubes have Ice storage bin needs clemlh_g. * Erupt) and wash bin. Discard old cubes. odor/taste

Food trmlsmitthag odor/taste * Wrap fi)ocls well.

to ice cubes. Interior of refrigerator * See Careand c/eaning.

needs clemlh_g.

Slow ice cube freezing Door left open. * Check to see it I)ackage, is holding door open.

Temperature control not set * See About the controls.

cold enough.

Noicecube Supply lh_e or shutoff * (:all a plumbex;

production valve is clogged.

Refrigerator has odor Foods trm_smitth_g * Foods with strong o(hn_ should be tightl) wrapped.

odor to refrigerator. * Keep an oI)en box of 1)aking, soda in the refl_gerator;

replace exerv three months.

Interior needs clemlh_g, * See Care and cleaning.

Moistnre collects inside Too frequent or too

(inhumidweather,air long door openings. carriesmoistureinto

refrigerator when doors are opened)

Interiotlightdoes No power at outlet. * ]_epla(e fuse or reset the breakei: not work

HotaNfrombottom

Food freezing in Food too close to air vent. * Move the fi)od axvav fl'om the air xent (near the controls).

Doordoes Rollers need adjusting. * See Rollers. by#self

Orange glowin Defrost heater is on. *This is n(mnal.

the freezer

Light bulb burned out. * See Replacingthelight bulbs.

Normal air flow cooling motor. In the refrigeration process, it is normaJ that heat be expelled in the

area under the refrigerator. Some floor coverings axe

sensitive and will discolor at these nonnaJ and

safe temperatures.

Refrigerator control is set * Moxe the refl'igerator control to a wai'/ner temperature. too cold.

Beforeyoucall forservice...

Troubleshooting -tips

Possible Causes What ToDo

Water dispenser Water supply line turned off * See Installing the water line.

does not work or not cmmected.

Water filter clogged. * Replace filter ('artlJdge or l'elllOVe filter and install })lug7

Air may be trapped in * Press the dispenser ann fin" at lea,4 2 minutes.

the water system.

Water spurting from Newly-hastaUed filter cartridge. • I_.uu water h'om the dispenser for 3 minutes

dispenser (about 1½ galh)us).

Water is not dispensed Water in reservoir is frozen • Set the refrigerator control to a wanuer setting and

but icemaker is working because the controls are wait 24 horus./f water does not dispense after 24 hotn_,

set too cold. call for service.

No water orice cube Supply line or shutoff valve * Call a plumbe_:

production is clogged.

Water filter clogged. * Replace filter cartrid,,e_ or remove filter and install lflu_'

S • "

Filter cm'tridge not * Remove and reinstall, filter cartfidoe,_ behw_ certain that

properly hastaUed, it locks into place. The blade on the end of the cartYidge

should be positioned vertically.,

Water is leaking from Glass not being held under * Hold the glass underneath the dispenser fin" 2-3 sec_mds

dispenser the dispenser long enough after releasing the dispenser button. Water may continue

after button is released, to dispense after the butt_)n is released.

Air may be present ha the water • Dispense water tk)i" at least 2 minutes to remove air from

line system causing water to drip system.

after being dispensed.

Water has poor Water dispenser has not been * Dispense water tmfil :ill water in system is

taste/odor used for a long time. replenished.

Water in fimtglass Normal when refrigerator • Wait 24 hotu_ fin" the refi'igerator to completely

is first installed, c_l (h_wn.

Water dispenser has not been * Dispense water until :ill water is system is used for a long time. replenished.

Water system has been drained. * _dh)w several horus for replenished supply to chill.

Actualtemperature not U_fit just plugged ha. * ?dlow 24 horns fin" s)'stem to stabilize.

equal to Set temperature

(on some models) Door open for too long. * ?dh _w 24 hotn_ fl n" system t() stabilize.

Wm-m food added to refrigerator. * _dlow 24 hotn_ fin" system to stabilize.

Defrost cycle is ha process. * _dlow 24 hotn_ fin" system to stabilize.

PerformanceData Sheet

SmartWaterFiltrationSystem

GSWF Cartridge

Thissystemhasbeen testedaccordingtoNSF/ANS142/53forreductionof thesubstanceslistedbelow. Theconcentrationofthe indicatedsubstancesin water entering thesystemwas reducedto a concentration

less thanorequal tothepermissible limit for water leavingthesystem,as specified inNSF/ANS142/53.*

(100%safety factors built in for unmetered usage)

Standard No. 42: Aesthetic Effects

Parameter

(:hlorin(

T & ()

Particulale*':

Parameter

Turbidity Cysts

I.ead aI pH 6.5 Lead aI pH 8.5

Lindane A1F,izine

* Tested using a flow rate of O.5 gpm; pressure of 60 psig; pH of 7.5 _+O.5; temp. of 68° -+5°F (20° -+3°C)

** Measurement in Particles/ml. Particles used were 0,5-1 microns *** NTU=Nephelometric Turbidity units

USEPA

MCL

USEPA

MCL

1 N'FU***

99.95% Reduction

0.015 mgiL

0.0902 mgiL

9.007 mgiL

hlfluent

Average

1.845 mgiI.

143,333 #imI

19.3 N'F[ ;'::**

200,000 #iL

0.15 mgiL

0.14 mgiI

0.0216 mgiL

0.(X)8 mgiL

hafluent Challenge

2.9 mgiL+19%

at least 10,000pardcles/mL

Influent

Average

Concentration

Average MaxiIllttnl

< 0.05 mgiI. 0.05 mgiL

29.83 #imL 140 #imI.

Standard No. 53: Health Effects

Iilfhlent Clr,dlenge Effluent

Effluent

Concentration

1+1 N'[-[ :::**

Minimmn 50,0(X) 1,

O.15 mgiI.+l 0%

0.15 mgiL+10%

0.002 mgiI.+l 0!:_

0.1X)9 mgiL+l 0%

Average

0.106 _FI f 0

< 0.(R)I mgiL

0.001 mgiI.

<0.00002 mgiL

< 0.(_)2 mgiL

Maxirll [inl

0.14 NT[ ;

< 0.001 mgiI

0.(x)3 mgiL

< 0.00902 mgiL

< 0.002 mgiI.

% Reduction

Average Mitmnum

> _ 7.2_ % 96.43!'{

99.98!'_ 99.91%

_, Reduction

Average

98.97%

> 99.99!:{ > 99.33!:{

> 99.29!:i

99.t)7%

> 76.129{

Mha. Required

Reduction

> 50%

>85%

Min. Required

Mitfimtmi Reduction

98.61% 9.5 N'F[ ;

> 99.99!:{ > 99.95!:i

>99.33!:i 0.010 mgiL

97.86% 0.010 mgiL

98.75% 0.0(_)2 mgiL

> 66.67:1 0.003 mgiL

Operating Specifications

• (;apacity: certified ti)r up to 750 gallons (2,838 1); up to six months

• Pressttre requirement: 40-120 psi (2.8-8.2 bar)

• Telllperattlre: 33-100°F (0.6-38°(])

• Flow rate: 0.5 gpm (1.9 lpm)

General Installation/Operation/Maintenance Requirements

• Hush new cartridge, at full flow for .3 minutes to Imrge, out trapped air.

• Replace cartridge when flow becolnes too sh)w.

Special Notices

• Installation instructions, parts and service availability, and standard warranty are inchtded with the prodttct when shipped.

• This driI_king water s_steln inust be inaintained according to inanuf,lcturer's instructions, ii_chtding rel)lacelnent of filter ca rtridges.

• Do not use with water that is microbiologically unsate or of unknown quality without adequate disinfection before or atter the sx:steln. Svstelns certified tor cyst reduction inav be used on disinli_cted water that inay contain filterable cysts.

• The COlmmdlmnts or other substances relnoved or reduced by this water treatn/ent svsteln are not necessarily in wmr

water.

• Check for compliance with the state and local laws and regulations.

• Note that while the testing was l)ertiwlned under standard laboratory conditions, actual l)erfornmnce nlav vary. Svstelns Inust be installed and operated in accordance with inanufilcturer's reconlnlended procedures and guidelines.

Svsteln lest(d an(1 c(rtifi((1 by NSF International agaillSl Standard 42 for th( r((h|ction of chlorin(, tast( and odor, particular( Class ] a d S a ad, d :)_ for the reduclion of (:7,'st, lead, Lindane, Atrazine and mrbidily.

3,Iant|factm-ed for: (;(neral Electri( (_ompany, I.ouisville, KY 40225

State of California

Department of Health Services

Water Treatment Device

Certificate Number

03-1559

Date Issued: April 28, 2003

Trademark/Model Designation

GE GSWF

Manufacturer: General Electric Consmner Products

Cysts Turbidity

Organic Contaminants

Atrazine Lindane 2,4-D

Replacement Elements

GSWF

to Section

lnorganic/Radiological Contaminants

Lead

Rated Service Capacity: 750 gal Rated Service Flow: 0.5 gpm

Conditions of Certification:

Do not use where water is microbiologically unsafe or with water of unknown quality, except that systems certified fbr cyst reduction may be used on disinfected waters that may contain filterable cysts.

+ 64 hidden pages