GE GSS25SGMDBS, GSS25JFMDWW, GSS25JFMCWW, GSS25JFMCCC, GSS22WGMDBB Owner’s Manual

...

GEAppliances.com

Safety Information

Adapter Plugs ................. 4

Electricity ..................... 4

Extension Cords ............... 3

Proper Disposal ................ '3

Safety Precautions ............ 2, 3

Operating Instructions

At_tomatic Icemaker ............ 9

Controls ..................... 5

Crispers and Pans ............ 8, 9

Ice and Water Dispenser ........ 10

Shelves, Bins and Racks ........ 6-8

Water Filter Cartridge ........... 6

Models20,22 and25

C6te gt c6te

R frig&ateurs

Lasection fran_aisecommence_ la page31

Care and Cleaning

Cleaning ................. 11, 12

Ligh tbulbs ................... 1'3

Installation Instructions

Preparing to Install

the Refrigerator ............ 14, 15

Water Line Installation .... 16-20

Troubleshooting Tips

Before You Call For Service . .22-25

Normal Operating Sounds ...... 22

Consumer Support

Consumer Support ..... Back Cover

Performance Data Sheet ........ 27

Product Registration ........ 29, 30

State of Caliibrnia Water

Treatment Device Certificate ..... 28

Warranty (Canadian) ........... 25

Warranty (U.S.) ............... 26

Lado a lado

Refrigeradores

La secci6nen espafiolempieza enla p6gina 59

Write yourmodeland serial numbershere: Model #

Serial#

Find these numbers on a label inside the refi'igerator compartment at the top

on the right side behind the controls.

197D3351PO03 49-60189 12-01JR

IMPORTANTSAFETYINFORMATION. READALLINSTRUCTIONSBEFOREUSING.

A WARNING!

Use this appliance only for its intended purpose as described in this Owner's Manual.

SAFETYPRECAUTIONS

When using electrical appliances, basic safety precautions should be followed, including the following."

{This refiigerator must be properly installed

and located in accordance with the Installation Instructions before, it is used.

{_Do not allow children m climb, stand or hang

on the shelves in the refiigeraton _i11eycould damage the refiigerator and seriously injure

themselves.

{Do not touch the cold surfaces in the freezer

compartment when hands are damp or weL Skin may stick to these extremely cold surfaces.

{_Do not store or use gasoline or other flammable

vapors and liquids in the vicinity of this or any other appliance.

{ In refiigerators with automatic icemakers,

avoid contact with the moving parts of the ejector mechanism, or with the heating element

that releases the cubes. Do not place fingers or hands on the mltomatic icemaking mechanism

while the refrigerator is plugged in.

@Keep fingers out of the "pinch point" areas;

clearances between the doors and hetween the doors and cabinet are necessarily small.

Be carefifl closing doors when children are in the area.

_ Unplug the refiigerator before cleaning and

making repairs.

NOTE:Westronglyrecommendthatanyservicingbe

performedbya qualifiedindividual.

_ Setting the freezer control to the 0 (off) position

does not remove power to the light circuit.

@Do not refreeze frozen foods which have

thawed completely.

ww_.GEAppliances.com

A DANGER!RISKOFCHILDENTRAPMENT

PROPERDISPOSALOFTHEREFRIGERATOR

Child enn'apment and suffocation are not problems of the past. Junked or abmldoned refiigerators are

still dangerous...even if they"will sit fbr ".just a few days." @you are getting rid of your old refiigerato_;

please follow the instructions below to help prevent

accidents.

Before YouThrowAway YourOldRefrigerator or Freezer:

@Take off the doors.

@Leave the shelves in place so that children may

not easily climb inside.

CFCDisposal

Your old refiigeramr may have a cooling system

that used CFCs (chlorofluorocarbons). CFCs are believed to harm sn'atospheric ozone.

If you are throwing away your old re@igerato_; make sure the CFC refrigerant is removed for proper

disposal by a qualified servicm: lfyou intentionally release this CFC refiigerant you can be subject to fines and imprisonment under provisions of

environmental legislation.

USEOFEXTENSIONCORDS

Because of potential safety hazards under certain conditions, we strongly recommend against the use of an extension cord.

However, ify_u must use an extension cord, it is absolutely necessary that it be a UL-listed (in the United

States) or a (_@-listed (in Canada), @wire grounding type appliance extension cord having a grounding

type plug and outlet and that the electrical rating of the cord be 15 amperes (minimum) and 120 volts.

IMPORTANTSAFETYINFORMATION. READALLINSTRUCTIONSBEFOREUSING.

A WARNING!

HOWTOCONNECTELECTRICITY

Do not, under any circumstances, cut or remove the third (ground) prong from the power cord. For

personal safety, this appliance must be properly grounded.

The power cord of this appliance is equipped with a 3-prong (grounding) plug which mates with a

standard 3-prong (grounding) ,a_ll oudet to minimize the possibility"of electric shock hazard

from this appliance. Have the wall outlet and circuit checked by a

qualified electrician to make sure the oudet is properly grounded.

If the outlet is a standard 2-prong oudet, it is your personal responsibility" and obligation to have it

replaced with a properly" grounded 3-prong wall oudeL

The refrigerator should always be plugged into its owql indMdual electrical oudet which has a voltage

rating that matches tim rating plate.

This provides the best performance and also prevents overloading house wiring circuits which

could cause a fire hazard fi'om overheated wires.

Never unplug your refiigerator by pulling on the power cord. _Mwaysgrip plug firmly and pull

sn'aight out from the outlet. Repair or replace immediately" all power cords that

have hecome frayed or otherwise damaged. Do not use a cord that shows cracks or abrasion damage

along its length or at either end. When moving the refiigerator away from the

wall, be careful not to roll over or damage the power cord.

USEOFADAPTERPLUGS_Adapt_rplugsnotpermitted in Canada)

Because of potential safety hazards under certain conditions, we strongly recommend against the use of an adapter plug.

Howevm, if you must use an adapte_, where local codes permit, a temporaryconnectionmay be made

m a properly grounded 2-prong wall outlet by"use ofa UL-listed adapter available at most local

hardware stores. The larger slot in the adapter must be aligned with

the larger slot in the wall outlet to provide proper polarity" in tim connection of tim power cord.

When disconnecting the power cord from the adapter, always hold the adapter in place with one

hand while pulling the power cord plug wifll the oflmr hand. If this is not done, the adapter ground

terminal is veiT likely to break with repeated use.

If the adapter ground terminal breaks, DONOTUSE the refrigerator until a proper ground has been

established.

Attachingtheadaptergroundterminaltoa waftoutlet

coverscrewdoesnotgroundtheapplianceunlessthe coverscrewis metal,andnot insulated,andthe waft

outletisgroundedthroughthehousewiring. Youshould havethecircuitcheckedby a quafifiedelectricianto make

surethe outlet isproperlygrounded.

READANDFOLLOWTHISSAFETYINFORMATIONCAREFULLY.

SAVETHESEINSTRUCTIONS

Aboutthe controlson the refrigerator. ._.OEApp,_,_._co,.

Initially, set the fresh food control at 5 and the freezer control at 5 and

allow 12hours for the temperature to stabilize.

Several adjustments may be required. Adjust the controls one increment at a time, and allow 12hours after each adjustment for the refrigerator to reach the temperature you set.

Setting the freezer control to 0 stops cooling in both the fresh food and freezer compartments but does not shut off electrical power to

the refrigerator.

Control settings will vary based on personal preferences, usage, and operating conditions and may require more than one adjustment,

Aboutthe water filter cartridge.

On some models

Water Filter Cartridge

The water filter cartridge is located in the back upper right corner of the refi'igerator

compartment.

When to Replace the Filter on Models With a Replacement Indicator Light

the water filter cartridge on the dispenser. This light will turn orange to tell you that

There is a replacement indicator light for

you need to replace the filter soon.

The filter cartridge should be replaced

Place the top of the cartridge up

when the replacement indicator light turns

insidethecartridgeholderand red or if the flow of water to the dispenser

slowly turn it to the right or icemaker decreases.

When to Replace the Filter on

The filter cartridge should be replaced

IndicatorMOdelsWithout a ReplacementLight

every sixmonthsorearlier if the flow of

water to the water dispenser or icemaker

decreases.

Installing the Filter Cartridge

O If you are replacing the cartridge, first

remove the old one by slowly turning it to the lefL DOnotpull down on the

cartridge. A small amount of water may drip down.

(on some models)

On models without a replacement indicator light, apply tim month and

yeas"sticker to the new cartridge to remind you to replace tim filter in six

months.

_Fill the replacement cartridge with

water fi'om the tap to allow for better flow from the dispenser immediately

after installation.

_ Lining up the arrow on the cartridge

and the carwidge holdm; place the top of the new cartridge up inside the holdel: De net push it up into

the holdel:

_ Slowly turn it to the right until the filter

cartridge stops. DONOTOVERTIGHTEN. As yvm turn the cartridge, it will

automatically raise itself into position. Cartridge will roVateabout 1/2 turn.

Rt]n water from the dispenser for 3 minutes (about one and a half,gallons)

to clear tim system and prevent sputtering.

_ Press and hold the RESETWATERFILTER

pad (on some models) on the dispenser for 3 seconds.

NOTE: A newlyqnstalled water filter

cartridge may cause water tospurt from the dispenser.

Filter Bypass Plug

You must use the filter bypass plug

when a replacement filter cartridge is not available. The dispenser and the icemaker

will ilot operate without dm filter or filter bypass plug.

ReplacementFilters: Toorderadditionalfilter cartridgesin

theUnitedStates,visitourWebsita, www.GEAppliances.com,orcall

GEPartsandAccessories,800.626.2002.

GWF Suggested Retail $34.95 USD.

Customers in Canada should consult the yellow pages for the nearest Camco Service

Center.

Abouttheshelvesand bins.

Not all features are on all models.

Bins on the Fresh Food Compartment Door

Adjustable bins can easily be carried from

refrigerator to work area.

Toremove:Lift the front of the bin up, then

pull out.

Toreplace or relocate: Engage the bin in the

molded supports of the door, and push in. Bin will lock in place.

The snuggerhelps prevent tipping, spilling

or sliding of small items stored on the door shelf Place a finger on either side of the

divider near the rear and move it back and forth to fit your needs.

Rearranging the Shelves RefrigeratorShelves:

ToRemove ToReplece

ww_.GEAppliances.com

FreezerShelves:

ToRemove

Slide-Out Spillproof Sheff fensomemodels)

'llle slide-out spillproof shelf allows you to reach items stored behind others. 'llle

special edges are designed to help prevent spills fi'om dripping to lower shelves.

Spillproof Shelves (onsomemodels)

FreezerBaskets:

ToRemove

Remove the basket by"pulling it forward, lifting up the fi'ont, and sliding it past the stop location.

Makesureyoupushtheshelvesall the wayback

in beforeyouclosethedoor.

Spillproof shelves have special edges to help prevent spills fronl dripping to

lower shelves.

i!(¸ii_i)_iii!iii!ili_ii_i/_!!_i!;il;i!!i!!;i!!!!_!;!i!!:!!!;;i!+!i!iiii!!i!/iil;!;il;;iiii!!iil;!!i_QuickSpace Shelf (onsomemo_ls)

i}i ,_, ._ 'L2_, ;!il;)i?i ¸

_.., -_-___r > This shelf splits in half and slides under

: itself fbr storage of roll items on the shelf

below.

Deep Door Shelves

Detachable shelf exmnders deepen and enclose fixed door shelves, providing

more storage room and greater storage flexibility.

Toremove: Lift the shelf extender straight

up then pull out.

TOreplace: Engage the shelf extender in the

molded supports on the door and push in. It will lock in place. 7

Aboutthe additionalfeatures.

Not all features are on all models.

ShelfSaver,. Rack

U_ this rock to stole beverage cans for easy access.

It can also hold a 9" x 13" baking dish.

Aboutthe crispersand pans.

Not all features are on all models.

iL_L_L_

.................. file trivet and at_ust it from side to side,

Excess water that may accumulate in the

bottom of the drawers should be ,a_ped dry.

Trivet and Divider (onsomemodels)

form. The divider will keep the larger fi'uits and vegetables fl'om falling or rolling onto

andandvegetables off the floor of the drawerThe n'ivet is designed to keep yourfi'uitSupaway from anyyoumOisturethat might

the more delicate ones. By lifting straight

on the divider, can detach it fi'om

then push down and into position.

_ _ Adjustable Humidity Crispers

Slide file control all file way to the Hiobor _ setting to provide high

humidity recommended for most

vegetables.

Fruitand Vegetable Crispers

Slide the control all the way to the Lowor

_6 setting to provide lower humidi W

levels recommended for most fruits.

Convertible Meat Pan

The convertible meat pan has its own cold air duct to allow a sn'eam of cold air from

the freezer comparmmnt to flow around the pan.

Thevariabletemperaturecontrolregaflates

the air flow from the freezer compartment.

Set control lever up to convert the pan to normal refrigerator temperature and

provide exn'a vegetable storage space. Cold air duct is turned ore Variable settings

between these extremes can be selected. Set control lever down to the coldest setting

to store flesh meats. If lever is left in meat position for a long period of time, some

fi'ost may form on the inside of the pan.

Aboutcrisper removal ww_.GEAppliances.com

Not all features are on all models.

Crisper Removal

Crispers can easily he removed by"tilting up slightly and pulling past stop location.

When replacing the crispers, make

sure you slide them through the

crisper guides,

Aboutthe automaticicemaker.

A newly-installed refrigerator may take 12-24 hours to begin making ice.

Automatic leemaker (onsomemodels)

_12qeicemaker willproduce seven culx-s per cycle_approximately 100-130 cubes

in a 24-hour period, depending on freezer compartment temperature, room

temperature, immber of door openings and otlmr use conditions.

If the refrigerator is operated before the water connection is made to the icemake_;

set the power switch in the 0 (Off}position. When the refrigerator has been coimected

to the water supply; set the power switch to the I (on)position.

_l_e icemaker will fill with water when it coots to 15°E A noMy-installed refrigerator

may take 12 to 24 hours to begin making ice cubes.

If the door prevents you from taking out the crispers, the refrigerator will need to

be rolled forward until the door opens enough to slide the crispers out. In some

cams, when you roll the refrigerator out, you will need to move the refrigerator to

the left as you roll it out.

If ice is not used frequently, old ice culx-s will become cloudy, taste stale and shrink.

If ice cubes get snmk in the icemakel;the green power light will blink. To correct this,

set the power switch to 0 (Off}and remove the cubes. Set the power switch to Hen}to

restart the icemaker. _M'terthe icemaker has been turned on again, flmre will be a delay

of about 45 minums before the icemaker resumes operation.

NOTE:Inhomeswithlower-than-averagewater pressure,youmayheartheicemakercyclemultiple

timeswhenmakingonebatchof ice.

_12qrowaway the first few batches of ice to allow the w-ater line to clear.

Be sure nothing interferes witll the sweep of the feeler arm.

It is normal for several cubes to bejoined togetlmr.

Ice Storage Drawer

Toaccessice, pull the drawer out. Toremove the drawer, pull it straight out

There is an upper freezer sheff

above the ieemaker that can be used for storage,

mad lift it past the stop location.

Icemaker Accessory Kit

lfyour refrigerator did not come already equipped with an automatic icemakm;

an icemaker accessory kit is available at extra cost.

Check the back of the refrigerator for the specific icemaker kit needed for

your model.

Aboutthe ice and water dispenser.

On some models

TOUse the Dispenser

SpiElShelf

Select CUBEDICE _, CRUSHEDICE or WATER_.

Press the glass gently against the top of the dispenser cradle.

The spill shelf is not self, training. To reduce ,a-ater spotting, the shelf and its

grille should be cleaned regaflarlT¢:

If no wateris dispensedwhentherefrigerator isfirst installed,theremaybeair inthewater

linesystem.Pressthedispenserarmfor at least two minutestoremovetrappedairfromthewater

lineandtofill thewatersystem.Toflushout impuritiesin thewaterline, throwawaythefirst

sixglassfulsofwater

CAUTION:Neverput fingersoranyother

objectsinto theicecrusherdischargeopening.

Ice Storage Drawer on Dispenser Models

Toremove:

Set the icemaker power switch to the

0 (off) position. Pull the drawer straight out and then lift past the stopposition.

Toreplace:

When replacing the drawm; make sure to push it firmly into place. If it does not

go all the ,a-ayback, remove it and rotate the drive mechanism 1/4 turn. _12qenpush

dm drawer back again.

Lockingthe Dispenser (onsomemodels)

Press the LOCK

CONTROLpad for

3 seconds to lock the

dispenser and control

panel. 'lb unlock, pre_s

and hold the pad again for 3 seconds.

Dispenser Light

_12qispad turns the

nightlight in the

dispenser on and off. The light also comes

7 7 7 7 7 7 7 7 7 7 7

?)i_ii()i()i()i()i()i()i()i()i()i()i()i()i()i()i()i

on when the dispenser cradle is pressed. If this

light burns out, it should be replaced with a 6 watt maximum,

12 volt DC bulb.

Important FactsAbout YourDispenser

%Do not add ice fi'om trays or bags to

the storage bin. It may not crash or dispense well.

NAvoid overfilling glass with ice and use of

narrow glasses. Backed-up ice can jam the chute or cause the door in the chute to

freeze shut. If ice is blocking the chute, poke it through with a wooden spoon.

N Beverages and foods should not be

quick-chilled in the ice storage bin. Cans, bottles or food packages in the

storage bin may cruise the icemaker or auger to jam.

NTo keep dispensed ice from missing

the glass, put the glass close to, but not touching, the dispenser opening.

_ Some crushed ice may be dispensed even

though you selected CUBEDICE._12qis happens occasionally when a few cubes

have been left in the cmshen

_N_ter crashed ice is dispensed, some

water may drip from the chute.

_ Sometimes a small mound of snow will

form on the door in the ice chute. _12qis condition is normal and usually occurs

when you have dispensed crushed ice repeatedly. _12qesnow will eventually

evaporate.

Careandcleaning of therefrigerator. GEApp,iancescom

Thedispenserdriparea, (on some models) Cleaning the Outside

beneath the grille, should be wiped dPfl Water left in this area may leave deposits. Remove

Oisponsordriparea. tim deposits by adding undiluted vinegar to

tim well. Soak until the deposits disappear or become loose enough to rinse away.

Thedispensercradle (on some models).

Before cleaning, lock the dispenser by" pressing and holding the LOCKCONTROL pad for 3 seconds. Clean with warm water

and baking soda solution--al)out a tablespoon (15 ml) of baking soda m a

quart (1 1)ofwatel: Rinse thoroughly and wipe dry:

Cleaning the Inside

TOhelp prevent odors,leave an open box of

baking soda in the fi'esh food and fi'eezer compartments.

Unplugthe refrigerator before cleaning. If dais

is not practical, wring excess moisture out of sponge or cloth when cleaning around

switches, lights or controls.

Use warm water and baking soda solution-- about a tablespoon (15 ml) of baking soda

to a quart (1 1)ofwatel: 'l]lis both cleans and neutralizes odors. Rinse and wipe dry.

_ter cleaning the door gaskets, apply" a thin layer of petroleum jelly to the door

gaskets at the hinge side. This helps keep the gaskets from sticking and bending out

of shape.

The door handles and trim. Clean with a

cloth dampened with soapy water. DIT with a soft cloth.

Keep the outside clean. Wipe with a clean cloth lightly" dampened with kitchen appliance wax or mild liquid dish detergent.

D W and polish with a clean, soft cloth.

Donot wipetherefrigeratorwith a soileddish

cloth or wet towel Thesemayleavea residue

thatcanerodethepaint. Donotusescouring

pads,powderedcleaners,bleachor cleaners containingbleachbecausetheseproductscan

scratchandweakenthepaint finish.

Drainopeningin freezercompartment.

During yearly cleaning, remove bottonl fi'eezer basket and flush a solution of

baking soda--1 Waspoon (5 ml) and 2 cups

(500 ml) of hot (not boiling) watm_

through dm drain line with the help of a meat basmE _illis will help eliminate odor

and reduce the likelihood of a clogged drain line. If drain becomes clogged, use a

meat basmr and baking soda solution to force the clog through the drain line.

Avoidcleaningcoldglassshelveswithhot water becausetheextremetemperaturedifferencemay

causethemtobreak.Handleglassshelves carefuflgBumpingtemperedglasscancauseit to

shatte_

Donot washanyplasticrefrigeratorpartsin the

dishwasher

Condenser

There is no need fbr routine condenser cleaning in normal home operating

enviromnents. Howew-_; in enviromnents that may be particularly dusty or greasy; the

condenser should be cleaned periodically for efficient refl'igerator operation.

Cleaning the condenser.

The condenser is located inside the back of the refrigeratol: _Ib access it, first unplug

the refi'igerato_: Then remove the access covel: The condenser is on tim right side.

Careand cleaning ofthe refrigerator.

Behind the Refrigerator

Be careflll when moving the refi'igerator away from the wall. All types of floor

coverings can be damaged, particularly cushioned coverings and those with

embossed surfaces.

Pull the refiigerator straight out and remm it to position by"pushing it straight in.

Moving the refrigerator in a side direction may result in damage to tim floor covering

or refiigeraton

Preparing for Vacation

For long v'acations or absences, remove food and unplug the refiigeraton Clean the

interior with a baking soda solution of one tablespoon (15 ml) of baking mda to one

quart (1 1) ofwatel: Leave the doors open. Set the icemaker power switch to the 0 (Off)

position and shut off the water supply to tim refiigeraton

Whenpushingtherefrigeratorback,makesure youdon'traftoverthepowercordor icemaker supplyline [on somemodels).

If"the temperature can drop below freezing, have a qualified servicer drain the

water supply system (on some models) to prevent serious property damage due to

flooding.

Preparing to Move

Secure all loose items such as grille, shelves and drawers by taping tbem securely in place to prevent damage.

Be sure the refrigerator stays in an upright position during moving.

Replacingthe lightbulbs. .. .GEA ,i..oos*om

Turning the control to the 0 (off) position does not remove power to the light circuit.

Fresh Food Compartment--Upper Light

Unplug the refrigerator.

OThe bulb is located Ix-hind the controls.

Replace with an appliance bulb of the

same or lower wattage.

Plug the refiigerator back in.

Fresh Food Compartment--Lower Light (onsomemodels)

This light is located above the top drawer _ _M_er replacing with an appliance

v bulb of the same or lower wattage,

Unplug the refrigeraml: replace the shield.

_ Grasp the lip at the bottom of the light _ Plug the refrigerator back in.

shield and pull it up and forward.

Freezer Compartment

Unplug dm refiigerator.

_ Remove the shelf just below light shield.

(The shelf will be easier to remove if it

is emptied first.)

Lift up on the light shield to remove.

_M}er replacing with an appliance

bulb of the same or lower wattage, reinstall the shield by hanging it

fi-orn the three tabs.

_ Reinstall the shelf and plug the

refiigerator back in.

Dispenser

Unplug the refiigerator.

_The bulb is located on the dispenser

under the control panel. Remove the lightbulb by turning

it counterclockwise.

Replace the bulb with a bulb of the same size and wattage.

Plug the refrigerator back in.

Installation

Refrigerator

Instructions

I Questions?Call800.GE.CARES(800.432.2737)orVisitour Wehsite at: www.GEAppliances.com

BEFORE YOU BEGIN

Read these instructions completely and carefully.

•IMPORTANT - Savethese

instructions for local inspector's use.

•IMPORTANT - Observeall

governing codes and ordinances.

• Note to Installer _ Besureto leavethese

instructions with the Consumm:

• Note to Consumer _ Keep these instructions

fbr future reference.

• Skill level - Installation of this applimlce requires basic mechanical skills.

In Canada,call 1.800.361.3400orVisitourWebsit_at:www.geappliances.ca

CLEARANCES

:Mlow the following clearances for ease of installation, proper air circulation and plumbing mad electrical

conllectiolls.

• Sides 1/8" (4 mm)

• Top 1" (25 mm)

• Back 1" (25 mm) A door clearance of 3/4" (19 mm) is needed for a 90 °

door opening which provides better access to the food storage area.

Models 20, 22,25

ROLLERS

• Completion time - Refrigerator Installation

• Proper installation is the responsibility of the installer.

• Product failure due to improper installation is not covered under the Warranty.

WATER SUPPLY TO THE ICEMAKER (on some models)

If the refrigerator has an icemakm, it will have to be connected to a cold v_-ater line. AGE water supply kit

(containing tubing, shutoff valve, fittings and

instructions) is available at extra cost fi'om your dealm, by"visiting our Website at www.GEAppllances.eom

(in Canada, at www.geappliances.ea) or fi'om Parts

mad Accessories, 800.626.2002.

15 minutes

The rogers have 3 purposes:

• Rollers adjust so the door closes easily when opened

about halfway. Rollers adjust so the refrigerator is firmly positioned

on tim floor and does not wobble. Rollers allow you to move the refiigerator away fi'om

the wall for cleaning.

To adjust the rollers, remove the base grille by pulling it out at the bottom.

Turn the roller at_usting screv_ clockwise to raise the refi'igerato_; counterclockwise to lower it. Use an

adjustable wrench (3/8" hex head bolt) or pliers.

REFRIGERATOR LOCATION

• Do not install the refiigerator where the temperature

will go below 60°F (16°C) becmlse it will not run often enough to maintain proper mmperatures.

• Install it on a floor strong enough to support it flfily loaded.

To replace base grille, line up tim clips on back of grille between the bar and the hottom of the cabineL Push

forward until grille snaps into place.

Installation Instructions

DOOR ALIGNMENT

Mter leveling, make sure that doors are even at the top. To make the doors even, adjust the refrigerator door.

O Using a 5/16' socket wrench, turn the door adjusting

screw to tim right to raise the door, to the left to lower it. (A nylon plug, embedded in the threads of the pin,

prevents tim pin from turning unless a wrench is

O used.)

zM'ter one or two turns of the wrench, open and close

the fresh fbod door and check the alignment at tim top of tim doors.

Toremovethebase grille,ogenthedoo_s

andthen pullthe grillestraightout

5/16"Socket

/ Wrench

--_1_ Raise

Installation Instructions

INSTALLING THE WATER LINE

BEFORE YOU BEGIN

Recommended copper w-ater supply kits are WX8X2, WX8X3 or WX8X4, depending on the amount of

robing you need. Approved plastic water supply lines are GE SmartConnect TM Refrigerator 'lllbing

(WX08X10002, WX08X10006, WX08X10015 and

WX08X10025). When connecting your refrigerator to a GE Reverse

Osmosis Water System, the only approved installation is with a GE RVKit. For other reverse osmosis water

systems, follow the manufacturer's recommendations. If the water supply to the refrigerator is from a Reverse

Osmosis Water Fihration System P-xND the refrigerator also has a water filter, use the refrigerator's filter bypass

plug. Using the refrigerator's water filtration cartridge in col_junction with the RO filter can resuh in hollow

ice cubes and slower water flow from the w-ater dispensen

This water line installation is not warranted by the refrigerator or icemaker manulgcturer. Follow these

instructions carefully to minimize the risk of expensive water damage.

Water hammer (water bmlging in the pipes) in house plumbing can cause damage to refrigerator parts and

lead to w-ater leakage or flooding. Call a qualified plumber to correct water hammer before installing

the wamr supply line to the reli'igeramr. _ib prevent burns and product damage, do not hook

up the w-ater line to the hot water line. If you use your refrigerator before connecting the

water line, make sure the icemaker power swdtch is in the 0 (Off) position.

Do not install the icemaker tubing in areas where temperatures fall below freezing.

When using any electrical device (such as a power drill) during installation, be sure the device is double

insulated or grounded in a manner to prevent the hazard of electric shock, or is battery powered.

zM1installations must be in accordance with local

plumbing code requirements.

WHAT YOU WILL NEED

• Copper or GE SmartConnect TM Refrigerator Tubing kit, 1/4" outer diameter to connect the refrigerator

to the water supply. If using copper, be sure both ends of the tubing are cut square.

To determine how much tubing you need: measure

the distance fi'om the w-ater valve on the back of the refrigerator to the water supply pipe. Then add 8'

(2.4 m). Be sure there is sufficient extra robing (about

8' [2.4 m] coiled into 3 turns of about 10" [25 cm] diameter) to allow the refrigerator to move out from

the wall after installation. GE SmartComlect TM Refrigerator Tubing Kits are

available in the following lengths: 2' (.6 m) -WX08X10002

6' (1.8 m) -WX08X10006

15' (4.6 m) - WX08X10015

25" (7.6 m) - WX08X10025 Be sure that the kit you select allows at least 8' (2.4 m)

as described above.

NOTE: The only GE approved plastic tubing is that supplied in GE SmartConnect TM Refrigerator Tubing kits. Do not use any other plastic water supply line because the line is under pressure at all times. Certain types of plastic will crack or rupture with age and cause water damage to your home.

Installation Instructions

WHAT YOU WILL NEED (CONT.)

Install the shutoffvalve on the nearest frequently used drinking wamr line.

• AGE water supply kit (containing tubing, shutoff valve and fittings listed below) is available at extra cost fi'om your dealer or from Parts and Accessories,

800.626.2002.

• A cold water supply. The water pressure must be bem_een 20 and 120 p.s.i. (1.4_8.2 bar) on models without a water filter and between 40 and 120 p.s.i.

(2.8-8.2 bar) on models with a ,a-ater filten

• Power drill.

• 1/2" or adjustable wrench.

• Straight and Phillips blade screwdriver.

• Two 1/4" outer diameter compression nuts and 2 ferrules (sleeves)--to connect the copper tubing

to the shutoff valve and the refi'igerator

water valve.

• If you are using a GE SmartConnecff MRefrigerator Tubing kit, the necessary fittings are preassembled to the tubing.

• If your existing copper water line has a flared fitting at the end, you will need an adapter (available at plumbing supply stores) to connect the water line to the refi'igerator OR you can cut off the flared fitting with a tube cutter and then use a compression fitting.

Do not cut formed end from GE SmartConnect TM Refi'igerator tubing.

[] SHUT OFF THE MAIN WATER

SUPPLY

Turn on the nearest faucet long enough to clear the line of water.

[] CHOOSE THE VALVE LOCATION

Choose a location for the valve that is easily accessible. It is best to connect into the side of a

vertical w-ater pipe. When it is necessary to connect

into a horizontal ,a-ater pipe, make the connection to the top or side, rather than at the bottom,

to avoid drawing off any sediment from the

w-ater pipe.

[] DRILL THE HOLE FOR THE VALVE

Drill a 1/4" hole in the water pipe (even if using a self-piercing valve) using a sharp bit. Remove may burrs resuhing from drilling tim hole in the pipe.

Take care not to allow water to drain into the drill. Failure to drill a 1/4" hole may"result in reduced

ice production or smaller cubes.

• Shutoff valve to connect to the cold water line.

The shutoff valve should have a wamr inlet with a minimum inside diamemr of 5/32" at the point of

connection to the COLD WATER LINE. Saddle-type shutoff valves are included in many water supply kits. Before purchasing, make sure a saddle-ty'pe valve complies with your local plumbing codes.

Installation Instructions

INSTALLING THE WATER LINE (cont.)

[] FASTEN THE SHUTOFF VALVE

Fasten the shutoffvalve to the cold water pipe with the pipe clamp.

PipeClamp

Saddle_TyDe_4 VerticalCold ShutoffValve Water Pipe

NOTE: Commonwealth of Massachusetts Plumbing Codes 248CMR shall be adhered to. Saddle valves

are illegal and use is not permitmd in Massachusetts. Consult with your licensed plumben

[] TIGHTEN THE PIPE CLAMP

Tighten the clamp screws until the sealing washer begins to swell.

NOTE: Do not overtighten or you may crush the tubing.

_lnlet End

Washer

[] CONNECT THE TUBING TO THE

VALVE

Place the compression nut and ferrule (sleeve) for

copper robing onto the end of the tubing and

commct it to the shutoff valve.

Make sure the tubing is fhlly inserted into the valve. Tighten the compression nut securely.

For plastic tubing from a GE SmartConnect TM

Refrigerator Tubing kit, insert the molded end

of the tubing into the shutoff valve and tighten

compression nut until it is hand tight, then tighten

one additional turn with a wrench. Overtightening

may cause leaks.

SaddleTyDe ShutoffValve SrnartConnectTM

Tubing

PackingNut

OutletValve

NOTE: Commonwealth of Massachusetts Plumbing Codes 248CMR shall be adhered to. Saddle valves

are illegal and use is not permitted in Massachusetts. Consult with your licensed plumber.

\ Ferrule{sleeve)

Nut

[] ROUTE THE TUBING

Route the tubing between the cold water line and the refrigerator.

Route the tubing through a hole drilled in the wall or floor (behind the refi'igerator or adjacent base

cabinet) as close to the wall as possible.

NOTE: Be sure there is sufficient extra tubing

(about 8' [2.4 m] coiled into 3 turns of about 10"

[25 cm] diameter) to allow the refrigerator to move

out from the wall after installation.

[] FLUSH OUT THE TUBING

Turn the main ,a-ater supply on and flush out the

tubing until the water is clear.

Shut the water off at the water valve after about

one quart (1 liter) of water has been flushed

through the robing.

Installation Instructions

[] CONNECT THE TUBING TO THE

REFRIGERATOR

NOTES:

• Befbre making the connection to the refrigerator,

be sure the refrigerator power cord is not plugged into the wall outlet.

• If your refrigerator does not have a water filtm, we recommend installing one if your ,_-aWr supply

has sand or particles that could clog the screen of the refrigerator's water valve. Install it in the

water line near the refrigeramn If using a GE SmartConnect TM Refrigerator Tubing kit, you will need an additional robe (WX08X10002)

to connect the fllren Do not cut plastic tube to install fiher.

Some models have the refrigerator connection at the end of tubing located outside the compressor

compartment access coven On other models, the compressor compartment access cover must he

removed in order to access the refrigerator connection at the water valve.

[]

CONNECT THE TUBING TO THE

REFRIGERATOR (CONT.)

Insert the end of the tubing into the refrigerator connection as far as possible. While holding the

tubing, tighten the fitting.

For plastic tubing from a GE SmartConnect Refrigerator 'lklbing kit, insert the molded end of

the robing into the refrigerator connection and tighten the compression nut until it is hand tight,

then tighten one additional turn with a wrench. Overtighrening may cause leaks.

Fasten the tubing into the clamp provided as shown to keep it in position. You may need to pry

open the clamp.

One of the illustrations below will look like the connection on your refrigerator.

Clamp

1/4" Compression,__

Nut

Tubing

On models using the refrigeration connection at the water valve, remove the plastic flexible cap.

Place the compression nut and ferrule (sleeve) onto the end of the tubing 2_sshown. On a GE

SmartCommct Refrigerator Tubing kit, the nuts are already assembled to the tubing.

Ferrule (sleeve)

Connection Tubing

Clamp

Ferrule

{sleeve)_

Connection Tubing

_SmartConnect _a

1/4"

SmartConnectTM

1/4"

Tubing

1_ TURN THE WATER ON AT THE

SHUTOFF VALVE

Tighten any commctions that leak.

Reattach the access cover.

Installation Instructions

INSTALLING THE WATER LINE (cont.)

[] PLUG IN THE REFRIGERATOR

zM'range the coil of tubing so that it does not vibrate against the back of the refl'igerator or against the

wall. Push the refl'igerator back to the wall.

START THE ICEMAKER

Set the icemaker power switch m the I (On}position. The icemaker will not begin m operate until it

reaches its operating temperature of 15°F (-9°C)

or below. It will then begin operation automatically

if the icemaker power switch is in the I (On}position.

NOTE: Ill lower water pressure conditions, the water valve may"turn on up to 3 times to deliver

enough water to the icemaker.

Notes.

"m_ b

"ml b

Normal operatingsounds.

The new high efficiency compressor rtlns fhster and will have a higher pitch hum or pulsating sound while operating.

throughout.

sound during the defi'ost cycle.

The flow of refrigerant through the freezer cooling coils sounds like boiling

during defrost and refiigeration fbllowing defrost.

Water dripping as it melts from the evaporator and flows to the drain pan

circulating air inside the fi'eezer which keeps the temperatures

on the defi'ost heater causing a sizzling, hissing or popping

gmgling noise.

,_of cooling coils cruised by expansion and contraction

tim defi'ost cycle.

Icemaker (on some models)

The icemaker water valve will buzz when the icemaker fills with water, ff the power switch is in the I {on) position, it will buzz even if it has not yet been hooked

up to water. Keeping the power switch in the I (on)position lx-fbre it is hooked up to water can damage tim icemaken rib prevent this, set the power switch to the 0

(Off} position. This will stop the buzzing. The sound of cubes dropping into the bin and water running in pipes as

icemaker refills.

These sounds are normal

and are due mostly to highly efficient operation.

Before youcall forservice...

Troubleshooting tips

Save time and money/.Review the charts on the following pages first and you may not need to call for service.

Possible Causes What To Do

Refrigerator in defrost cycle. * Wait about 30 minutes for defi'ost cycle to end. Freezer control * Move the freezer control to a temperature setting.

in 0 (off) position. Refrigerator is unplugged. * Push the plug completely into the outlet.

The fuse is blown/circuit • Replace fuse or reset the breaker. breaker is tripped.

Vibration_i rattling : :

Front rollers need adjusting. • See Rollers.

i i Oili i!i! iii!i:i¸'iiiiiiiiiiiiiii!ii iiii!ii iiii!ii iiii!ii iiii!ii iii!i i

ww_.GEAppliances.com

Possible Causes What ToDo

lllloto_operate_ Normal when refrigerator * Wait 24 hours ioi" the refrigerator re completely

is First plugged in. cool down.

(Mode_ Often occurs when large • 'Ilfis is normal.

amounts of food are

placed in refrigerator.

_ezer_uire_O_ Door left open. • Check to see if package is holding door open.

Hot weather or frequent • 'llfis is normal. door openings.

Temperature controls • See About the controls.

........... ....... setting.

O_froze_fo_ ; :

set at the coldest

Temperature control not set • See About the controls. cold enough.

Warm weather or frequent • Set the temperature control one step colden

door openings. See About the controls. Door left open. • Check to see if package is holding door open. Door left open. • Check to see if package is holding door open.

Too frequent or too long door openings.

Automatic energy saver • This helps prevent condensation on the outside.

system circulates warm liquid around front edge of freezer compartment.

Icemaker power switch • Set the power switch to the I (on) position.

is in the O (off) position. Water supply turned off or • See Installing the water line.

not connected.

Freezer compartment • Wait 24 hours tor the refrigerator re completely too warm. cool down.

Piled up cubes in the storage • Level cubes by hand. bin cause the icemaker

to shut off.

Ice cubes stuck in icemaker. • 'lhrn off the icemakel; remove cubes, and turn the

(Green power light on icemaker back on.

icemaker blinking). Ice storage bin needs cleaning. • Empty and wash bin. Discard old cubes.

Food transmitting odor/taste • Wrap tbods well. to ice cubes.

Interior of refrigerator • See Care and cleaning. needs cleaning.

Water Filter clogged. • Replace filter cartridge with new cartridge or with plug. Door left open. • Check to see if package is holding door open.

Temperature control not set • See Aboot the controls.

..........................................................................cold enough.

Door gasket on hinge side _pply petroleum jelly on Face of gasket. sticking or folding over.

Defrost heater is on. • This is normal.

•£

Before youcall forservice...

Possible Causes What ToDo

Icemaker turned off or * _ihrn on icemaker or water supply: water supply turned off.

Ice cubes are frozen to * Remove cubes. icemaker feeler arm.

Irregular ice clumps in * Break up with fingertip pressure and discard storage container, remaining clumps.

Dispenser is LOCKED. • Press and hold the LOCKCONTROLpad for 3 seconds. Water dispenser has not been • Dispense water until all water in system is replenished.

nsed for a long time. Normal when refrigerator • Wait 94 hours for dm refrigerator to completely

is First installed, cool down. Water dispenser has not been • Dispense water until all water in system is replenished.

used for a long time. Water system has been drained. • :Mlow several hours for replenished supply to chill. Water supply line turned • See Installing the water line.

off or not connected.

• Freezer may be too warm. Adjust the freezer control

m a colder setting, one position at a time, until clmnps do not form.

Water filter dogged. • Replace filter camidge or remove filter and install plug. Air may be trapped in the • Press dm dispenser arm for at least two minutes.

water system. Dispenser is LOCKED. • Press and hold the LOCKCONTROLpad for 3 seconds.

Newly-installed Filter cartridge. • Run water from the dispenser for 3 minutes (about

one and a half,gallons).

Water in reservoir is • Call for service.

f ozeu.

Supply line or shutoff • Call a plumber. valve is clogged.

Water filter dogged. • Replace filter camidge or remove filter and install plug. Dispenser is LOCKED. • Press and hold the LOCKCONTROLpad for 3 seconds.

Foods transmitting • Foods with strong odors should be tightly wrapped. odor to refrigerator. • Keep an open box of baking soda in the refiigerator;

replace every dn'ee months.

Interior needs cleaning. • See Care and cleaning. Defrost water drainage • See Care and cleaning.

system needs cleaning. Not unusual during • Wipe surface dry.

periods of highhumidity.

Too frequent or too

long door openings.

No power at outlet. • Replace fuse or reset the breaker: Light bulb burned out. • See Replacing the light bulbs.

Drain in the bottom of • See Care and cleaning. the freezer clogged.

Cubes jammed in chute. • Poke ice through with a wooden spOOll.

CUBEDICEwa_Ie#ted butCRUSHEDICEwas;

Your refrigerator is warranted to be free of defects in material and workmanship.

What is covered How Long Warranted Parts Labour

Compressor Five (5) Years Five (5) Years Five (5) Years

Sealed System (including Five (5) Years Five (5) Years Five (5) Years evaporator, condenser tubing and refrigerant)

All Other Parts One (1) Year One (1) Year One (1) Year

ww_.GEAppliances.com

Possible Causes What ToDo

Normal air flow cooling motor. In the refrigeration

process, it is normal that heat be expelled in the area under the refiJgerator. Some floor coverings are

sensitive and will discolor at

these normal and safe temperatures. Last setting was CRUSHED ICE. • A few ctdx-s were left in the crusher from the previous

setting. This is normal.

CONSUMER WARRANTY

(for customers in Canada)

(From Date of Sale) Repair or Replace

at Camco's Option

TERMS AND CONDITIONS:

This warranty applies only for single family domestic use in Canada when the

Refrigerator has been properly installed

WHAT IS NOT COVERED:

• Service trips to your home to teach you how

to use the product.

• Damage to finish after delivery.

according to the instructions supplied by Camco and is connected to an adequate

and proper utility service.

Damage due to abuse, accident, commercial use, and alteration or defacing of the serial plate cancels all obligations of this warranty.

• Improper installation--proper installation includes adequate air circulation to the

refrigeration system, adequate electrical, plumbing and other connecting facilities.

• Replacement of house fuses or resetting of circuit breakers.

Service during this warranty must be performed

by an Authorized Camco Service Agent.

Neither Camco nor the Dealer is liable for any claims or damages resulting from any failure of the Refrigerator or from service delays

beyond their reasonable control. To obtain warranty service, purchaser must

present the original bill of sale. Components repaired or replaced are warranted through the

remainder of the original warranty period only.

• Replacement of lightbulbs.

• Damage to product caused by accident, fire, floods or acts of God.

• Loss of food due to spoilage.

• Proper use and care of product as listed

in the owner's manual, proper setting of controls.

• WARRANTOR iS NOT RESPONSIBLE

FOR CONSEQUENTIAL DAMAGES.

This warranty is in addition to any statutory warranty.

IMPORTANT Keep this warranty and your bill of sale as proof of original purchase and purchase date.

Camco Service is available coast to coast.

If further help is needed concerning this warranty, contact: Manager, Consumer Relations, Camco Inc.,

Suite 310, 1 Factory Lane, Moncton, N.B. ElC 9M3

Staple your receipt here.

Proofof the original purchase

date is needed to obtain service

under the warranty.

RefrigeratorWarranty.(Forcustomers in the United States)

All warranty service provided by our Factory Service Centers,

or an authorized Customer Care® technician. Toschedule service, on-line, 24 hours a day, visit us at www.GEAppliances.com, or call

800.GE.CARES (800.432.2737).

GE Will Replace:

Anypartof the refiigerator which Pails due to a defect in materials or workmanship.

During this full one-year warranty,,GE will also provide, free ofcha_e, all labor and in-home

service to replace tim defective part.

Anypartofthesealedrefrigeratingsystem(the compressor, condensm; evaporator and all connecting robing) which fails due m a defect in mamrials or workmanship.

During this full five-yearsealed refrigeratingsystemwartang GE will also provide, free of cha_e,

all labor and in-home service to replace the defective part in the sealed refiigerating system.

/_)_Service trips to your home to teach you how to use the

product.

_ Improper installation. /_)_Failure of the product if it is abused, misused, or used for

other than the intended purpose or used commercially.

_ Loss of food due to spoilage. /_ Replacement of house fuses or resetting of circuit

breakers.

Staple your receipt here.

Proof of the original purchase

date is needed to obtain service

under the warranty.

/_ Replacement of the water f'titer cartridge due to water

pressure that is outside the specified operating range or due to excessive sediment in the water supply.

/_S_Replacement of water filter cartridge after its expected

useful life.

/_ Damage to the product caused by accident, fire, floods or

acts of God.

/_ Incidental or consequential damage caused by possible

defects with this appliance.

This warranty is extended to the original purchaser and any succeeding owner for products purchased for home

use within the USA. In Alaska, the warranty excludes the cost of shipping or service calls to your home. Some states do not allow the exclusion or limitation of incidental or consequential damages. This warranty gives

you specific legal rights, and you may also have other rights which vary from state to state. Toknow what your legal rights are, consult your local or state consumer affairs office or your state's Attorney General

Warrantor: General Electric Company.Louisville, KY 40225

Performance Data Sheet

GESmartWater Filtration System

GWF Cartridge

Health Claim Performance Certified by NSF/ANSI*

'I00% safety factors built in for unmetered usage)

Standard No. 42: Aesthetic Effects

Parameter

Chlorine T&O Particulate**

Parameter

Turbidity

Cysts

Lead at PH 6.5 Lead at pH 8.5

Lindane Atrazine

2,4-D Asbestos

* Testedusing a flow rate of 0.5 gpm; pressure of 120psig; pH of Z5-+0.5;temp. of 20-+2.5C ** Measurement #7partioles/ml *** NTU = Nephelometrio Units

USEPA

MCL

USEPA

MCL

1 NTU***

99.95% Reduction 15 ppb

15 ppb

0.0002 ppm

0.003 ppm

0.100 ppm 99%

Influent

Challenge

1.9 ppm

200,000

Standard No. 53: Health Effects

Influent Effluent

Challenge

24.3 NTU

Average Maximum

0.02 ppm 0.05 ppm

3,978 7,800

Average

0.07 NTU

105,750

160 ppb 150 ppb

0.00062 ppm

0.0084 ppm

0.272 ppm

690 MFL/ml

1 ppb

1.8 ppb

0.00005 ppm

0.002 ppm

0.042 ppm

0.32 MFL/ml

Effluent

Maxinlunl

0.1 NTU 55

1 ppb

4.3 ppb

0.00005 ppm

0.003 ppm

0.090 ppm

1.2 MFL/ml

% Reduction

Average Minimum

98.90% 97.37%

98.00% 96.10%

% Reduction

Average

99.71%

99.97%

99.37%

98.80%

91.93%

76.19%

84.89%

99.95%

Minimum

99.59%

99.95%

99.37%

97.13%

91.93%

64.28%

67.63%

99.82%

Operating Specifications

_ Capacity: certified for up to 300 gallons (1135 1); up to six months for models without a replacement fiher indicator

light; up to one year for models with a replacement filter indicator light

_/_Pressure requirement: 40-120 psi (2.8-8.2 bar), non-shock N'Ibmperature: 33-100 F (0.6-38 C)

_Flow rate: 0.5 gpm (1.9 lpm)

General Installation/Operation/Maintenance Requirements

_/Flush new cartridge at full flow J[br 3 minutes to purge out trapped ail: _ Replace cartridge when flow becomes too slow.

Special Notices

_/Installation instructions; parts and smwice availability; and standard warranty are included with the product when shipped. _This drinking v_-ater system must be maintained according to manufacturer's instructions, including replacement of

filter cartridges.

_Do not use with water that is microbiologically unsafe or of tmknown quality without adequate disinfection before or

after the system. Systems certified for cyst reduction may be used on disinfected v_-ater that may" contain filterable cysts. N/The contaminants or other substances removed or reduced by this water treatment system are not necessarily in your waten _ Check for compliance with the state and local laws and regulations.

System 'l_-sted and Certified by NSF International against ANSI/NSF Standard 42 & 53 for the reduction off

Standard No. 42: Aesthetic Effects Chemical Unit

'Paste and Odor Reduction (]hlorine Reduction, (]lass i

Mechanical Filtration Unit

Particulate Reduction, Class 1

Standard No. 53: Health Effects Chemical Reduction Ulfit

Lead and Atrazine Rc(hmtion Lindane and 2,4-D Reduction

Mechanical Filtration Unit

'liirbidity Reduction

Cyst and Asbestos Reduction

Manufactured for: General Electric Compmly, Louisville, KY 40225 2 7

+ 61 hidden pages