GE GSS23QGTMWW, GSS23QGTMBB, GSS23QGTLWW, GSS23QGTLCC, GSS23QGTLBB Owner’s Manual

...

Safety Instructions. ........... 2-4

ge.com

Operating Instructions

Additional Features ............ 10

Automatic Icemaker ............ 12

Care and Cleaning .......... 14, 15

Crispers and Pans .............. 11

Ice and Water Dispenser ..... 13, 14

Refrigerator Doors .......... 10, 11

Replacing the i,ight Bulbs ....... 16

Shelves and Bins .............. 8, 9

Temperature Controls ........... 5

TurboCool'" .................... 6

Water Filter .................... 7

Installation Instructions

Installing the Refrigerator .... 22-25

Preparing to Install

the Refrigerator ............ 17-19

Removing and

Replacing Doors ............ 19-21

Water Line Installation ....... 26-28

Troubleshooting Tips ....... 30-32

Normal Operating Sounds ....... 29

Models23and25

C6te fiC6te

Rdfrigdrateurs

La section fran_aise commence a la page 42

Lado a Lado

Refrigeradores

La seccidn en espa_ol empieza en la pagina 76

Consumer Support

Consumer Support ..... Back Cover

Performance Data Sheet ........ 38

Product Registration

(Canadian) ................ 35, 36

Product Registration

(U.S.) ..................... '.43, '.44

State of California Water

Treatment Device Certificate ..... 39

Warranty (Canadian) ........... 40

Warranty (U.S.) ................ 41

Write the model and serial numbers here:

Find these numbers on a label inside the refrigerator compartment at the

top on the right side.

2001)8074['004 49-60413-1 02-08JR

IMPORTANTSAFETYINFORMATION. READALLINSTRUCTIONSBEFOREUSING.

a, WARNING'!

Use this appliance only for its intended purpose as described in this Owner's Manual

SAFETYPRECAUTIONS

When using electrical appliances, basic safety precautions should be followed, including the following:

This refligerator must be properly installed and located in accordance with the Inst_fllation

Instructions before it is used.

Do not allow children to climb, stand or hang on the shelves in the reffigeramI: They could

&mmge the refrigerator and seriously i_jure themseNes.

{{Do not touch the cold surfaces in the fleezer

compamnent when hands are damp or wet. Skin may stick to these extremely cold surfaces.

{{Do not store or use gasoline or other flammable

vapors and liquids in the vicinity of this or any other appliance.

In refl_igeramrs wit1 automatic icemakers, avoid contact with the moving parts of the

ejector mechanism, or with the heating element locamd on the bottom of the icemake_.

Do not place fingers or hands on the automatic icemaking mechanism while the refligeramr

is plugged in.

Keep fingers out of the "pinch point" areas; clearances between the doors and between

the dooIs and cabinet are necessarily small. Be careflfl closing doors when children are

in the area.

Unplug file refligemmr before cleaning and making repai,_.

NOTE:Westrong/}/recommendthatan}/servicingbe performedbyaquafifiedindividual

{{Setting either or both controls to 0FFdoes not

remove power to the light circuit.

{{Do not refleeze flozen foods which have

thawed completel):

ge.com .............

DANGER! RISK OFCHILDENTRAPMENt---

PROPERDISPOSALOFTHEREFRIGERATOR

GhiM entrapment and suffbcadon are not problems CFCDisposal of tile past. Junked or abandoned refligeratoI_ are

still _l)mgerous...even if they will sit for "just a few Your old refl-igerator may have a cooling syst days. If you are getting _q_dof your old refl_igeratoi, that used CFCs (chlorofluorocarbons). ,uc

please follow the instructions below to help prevent believed to harm stratospheric ozone. _} accidents. If you are throwing away your old refligemto_; make

BeforeYouThrowAway YourOldRefrigerator surethe GFGrefligerantisremovedfor proper

Freezer: disposal by a qualified serviceL If you intentionally _,

• lke off the doors, fines and imprisonment under provisions of I,eave the shelves in place so that children may enviromnenml legislation. '_'a

not easily climb inside.

release this CFC refl-igerant, you can be subject to q

USEOFEXTENSIONCORDS

Because of potential safety hazards under certain conditions, we strongly recommend against the use of an extension cord. -_"

CFCs

However, if you must use an extension cord, it is absolutely necessaD_ that it be a UIAisted (in the United _' States) or a GSA-listed (in Ganada), _gwire grounding type appliance extension cord having a grounding

type plug and outlet and that the electrical rating of the cord be 15 amperes (minimum) and 120 volts. _"

IMPORTANTSAFETYINFORMATION. READALLINSTRUCTIONSBEFOREUSING.

A WARNING'!

HOWTOCONNECTELECTRICITY

Do not, under any circumstances, cut or remove the third (ground) prong from the power cord. For personal safety, this appliance must beproperly grounded.

The power cord of dlis appliance is equipped with a 3-prong (grounding) plug which mates wifll a standard 3-prong (grounding) waU outlet

to minimize the possibilil 0, of electric shock hazard

fiom this appliance.

Have the wall oudet and circuit checked by

a qualified electrician to make sure the outlet

is properly grounded.

If die oudet is a standard 2-prong oudet, it is

your personal responsibility and obligation m

have it replaced with a properly grounded

3-prong waU oudet.

The refligerator should ahvays be plugged into

its own indMdual electrical oudet which has

a voltage rating that matches the rating plate.

This provides the best performance and also prevents overloading house wiring circuits which

could cause a fire hazard flom overheated wires. Never unplug your refligerator by pulling on

the power cord. Ahvays grip plug firefly and pull straight out flom the outlet.

Repair or replace immediamly aU power cords dlat have become flayed or otherwise damaged. Do not

use a cord that shows cracks or abrasion damage along its length or at either end.

x_qlen moving the refligerator away flom the waU, be careflfl not to roll over or damage the

power cord.

READANDFOLLOWTHISSAFETYINFORMATIONCAREFULLY. SAVETHESEINSTRUCTIONS

Aboutthe temperaturecontrols, geoom

The temperature controls are preset in the factory at5 for both the refrigerator and freezer compartments. Allow 24 hours for the temperature to stabilize to the preset recommended settings.

Several adjustments may be required. Each time you adjust controls, allow 24 hours for the refrigerator to reach the setting you have selected.

Setting either or both controls to 0 stops cooling in both the freezer and refrigerator compartments, but does not shut off electrical power to the refrigerator.

Control settings will vary based on personal preferences, usage and operating conditions and may require more than one adjustment.

NOTE: The refrigerator is shipped with protective film covering the temperature controls. If this film was not removed during installation,

remove it now.

PerformanceAir FlowSystem

The Performance Air Flow Sysmm is designed to maximize mmperaulre conuol in file iefligerator and fleezei compartments. This unique special feaulre consists of the Air Tower along the back waU of the

refligerator and the Air Tunnel on the bottom portion of the fieezer rear wall. Placing food in fiont of the louvers on these components will not aftbct perfommnce. Although the Air Tower and the Air Tunnel can

be removed, doing so will aft>ct temperature pe_foimance. (Fox removal insuucfions, on-line, contact us at ge.com o, call 800.GE.(;ARES. In (;anada, contact us at geappliances.ca or call 1.800.561.3344.)

About TurboCooLTM (onsome models)

How it Works

TurboCoolral)idly cools file refligermor

compamnent in order m more quickly cool foods. Use rurboCoolwhenadding a

large amount of food to the refrigerator

compartment, putting away foods after they have been sitting out at room temperature

or when putdng away warn1 leftovers. It can

also be used if the refligeramr has been without power for an exmnded period.

Once activamd, the compressor will mrn on immediately and the fans will cycle on and

off at high speed as needed for eight horns.

The compressor will continue m run until

the reflJgerator compartment cools m

approximately 34°F (1°C), then it will cycle

on and off to maintain this setting. Afker 8 hours, or if rur/JoCoolis pressed again, the

refligeramr compartment will return m tile original set6ng.

Howto Use

Press TurboCool.The refligemtor mmpemmre display will show 9 (die coldest

setting).

AtXerTurboCooliscomplete, the

refligeramr compartment will return m the origdnal setting.

NOTES:The refligeramr mmperamre

cannot be changed during

rurboCoot

The fleezer mmperamre is not affbcmd dining TurboCool.

When opening the refrigerator

door during TurboCootthe f.ns

will continue to run if they have

cycled on.

Aboutthe water filter.(onsome models)

On some models

ge.com

Water Filter Cartridge

The water filter cartridge is located in the back upper fight corner of the reflJgerator compartment.

When to Replace the Filter on Models With a

Replacement Indicator Light

There is a replacement indicator light for the water filter cartridge on the dispenser. This light will utrn orange to roll

you that you need m replace the filmr soon.

The filter cartridge should be replaced when the replacement indicator light turns red or if the flow of water

to the dispenser or icemaker decreases.

When to Replace the Filter on Models Without a

Replacement Indicator Light

The filter cartridge should be replaced evecy six months or earlier if the flow ofwamr m the wamr dispenser or

icemaker decreases.

Removing the Filter Cartridge

If you are replacing the cartridge, first remove the old one by slowly unning it m the left. DOnotpull down on the

cartridge. A small amount of water mW drip down.

Installing the Filter Cartridge

O Slowly turn it to the fight until the filter cartridge stops.

DONOTOVERTIGHTEN.As you unn the cartridge, it will atttomafically raise itself into position. The cartridge will move about 1/2 turn.

O Run water from the dispenser for 3 minutes (about

1-1/2 gallons) to clear the system and prevent

sputtering. Press and

FILTERpad

(on some

;) on

RESETWATERFILTER the dispenser

HOLD3SECS lot" ,_ seconds.

t",,a

=4"

....7::,_ii,?iiiiil

iiiiiiii_iiiii(iiiiii_i_i'ii

_,,:iiiiLii_i_iii_ii,ii

t{i_iiiitiiii{ii_ii

=4"

O If you are replacing a SmartWatercartrklge with an

adapter, the adapter illttst be removed before installing the cartridge. To remove the adapter; turn it to the left about 1l/4 unn.

If you are replacing a Waterby Cu/figancartridge, leave the adapter in place. This adapter will stay in the

refligerator when you replace future camidges.

i _ _i i i _ii

,, r -,

With adapter Withoutadapter

(appearance may vary)

On models without a replacement indicator light, apply the month and ),eat sticker to the new caruidge

to remind you to replace the filter in six months.

Fill the replacement cartridge with water flom the mp to allow for better flow flom the dispenser immediately

after installation.

O IJne tap the arrow on the cartridge and the cartridge

holder. Place the top of the new cartridge up inside the holder. Donot push it up into the holder.

NOTE:A newly-installed water filter cartridge may cause

Filter B! ,,,,,

waterto sourtfl-o_e_,_,, dispensel_

Youmus _ L_J] ssi:, --_--_ ' relent

_,......... _Filter/ .JI ,-." LHter/" _ _ tl.o

n:tc/ _a_ _ _ _ xc. B,,n_ee _ ....

icemake, _uPgass _ irt,, PlYu_g"°° ; :r

bypass pl

SmartWater WaterbyCulligan

To use the filter bypass plug on WaterbyCulliganmodels, yott IIlttst f]pstremove the filter adapter flom the cartridge

hoMer by unning it to the left.

ffyou have questions--visit our Website at ge.com,

or call 1.800.GE.CARES 11.800.432.2737).

Replacementfilters: Toorderadditionalfiltercartridgesin theUnitedStates,

visitourWebsiteatge.com,orcall GEPartsandAccessories,

t",,a

=4"

,,,=z=,,,

,mla4 ,,,w=,|

r,,/,3

;:x

Abouttheshelvesandbins.

Not all features are on all models.

' Refrigerator Door Bins

The refligerator door bins are adjusmble.

Toremove:I,iff the fiont of the bin straight

up, then lift up and out.

Toreplaceorrelocate:Engage file back side

of the bin in file molded supports of the dooL Then push down on the flont of the

Refrigerator bin

bin. Bin will lock in place.

Deep Door Shelves

Thesnugger helps prevent tipping, spilling

or sliding of small items stored on the door shelf. Place a finger on either side of the snugger near the rear and move it back

and forth m fit your needs.

Press tab andpull shelf forward to remove

Detachable shelf exmnders deepen and

enclose fixed door shelves, providing

more sm_ge room and greater storage flexibility.

Slide-Out Spillproof Shelf

The slide-out spillproof shelf aUows you

m reach imms stored behind others. The

special edges are designed m help prevent spills flom dripping to lower sheNes.

Toremove:

Slide the shelf out until it reaches the stop, then press down on the tab and slide the

shelf smdgbt out.

Toreplaceorrelocate:

I,ine the shelf up with the supports and slide it into place. The shelf can be

reposidoned when the door is at 90 ° or

more. To reposidon the shelf, slide the shelf

past the stops and angle downward. Slide shelf down m the desired position, line up with the supports and slide into place.

Makesureyoupushtheshelvesall thewayback

in beforeyoudose thedoor.

Toremove:I,ift the shelf extender straight

up then pull out.

Toreplace:Engage the shelf extender in the

molded supports on the door and push in. It will lock in place.

Not all features are on all models.

ge.com

This shelf splits in half and slides under

itself for storage of tall items on the shelf

below.

OuickSpace TM Shelf

This shelf can be removed and replaced

or relocatedj ust like Slide-.Out Spillproof Shelves.

Slide-Out Freezer Shelves

Toremove, slide out to the stop position,

lift the fiont past the stop position, and slide out.

Fixed Freezer Shelves

Toremove, lift the shelf up at the left side

and then bring the shelf out.

On some models, this shelf can not be used in the lowest position.

Makesureyoupushtheshelvesall the wayback in beforeyouclosethe door.

Abouttheadditional features.

Not all features are on all models.

ShelfSaver TM Rack

(onsomemodels)

Use this rack to store

beverage cans for easy

access.

It can also hoM a 9" x 13"

baking dish.

Removable Beverage Rack

The beverage rock is designed to hold a bottle on its side. It can be attached

to any slide-.out shel£

Door Can Rack

(onsomemodels)

This door rack holds up to 9 cans.

NOTE:Thisrackcanonlybe mountedin thetopposition

underthedairybin.

Toinstall:

O I,ine up the huge part of the slots on

the top of the rack with the robs under the shelf.

O Then slide the rack back to lock it

in place.

Abouttherefrigeratordoors.

Refrigerator Doors

The refligerator doors may feel diffbrent

fllan die ones you are used to. The special

door opening/closing feature makes sure

the doors close all the way and are securely sealed.

When opening and closing die door you will notice a stop position. If the door is

opened past this stop point, the door will

remain open m allow you m load and

unload food more easily.When the door is only partially open, it will automatically

close.

When the door is only partially open,

it will automatically close. Beyond this stop the door will

stay open.

The resistance you feel at the stop position will be reduced as the door

is loaded with food.

Door Alignment

ge.com

If (loots are uneven, adjust tile refrigerator

(loot;

O Using a 7/16" wrench, utrn tlle (loot

adjusting screw to the dght to raise the

door; to the left m lower it.

(A nylon plug, imbedded in the

threads of the pin, prevents the pin

from utrning unless a wrench is used.)

Aboutthe crispersandpans.

Not all features are on all models.

Fruit and Vegetable Crispers

Excess water dmt may accumulate in the bottom of the drawers should be wiped dry.

0 At_er one or two turns of tile wrench,

open and close the refligerator door and check the aligmment at the top

of the doors.

Adjustable Humidity Crispers

Slide the control all tile way to tlle H/setting to provide high humidil),

recommended for illost vegetables.

Aboutcrisperremoval

Not all features are on all models.

Crisper Removal

Crispers can easily be removed by pulling tlle drawer straight out and lifting tile

drawer tap and over tile stop location.

Slide the control all the way to the LOsetting to provide lower humidity

levels recommended for most fluits.

If die door prevents you flom taking out the drawers, first try m remove the door

bins. If this does not oflbr enough clearance, the refligerator will need m

be rolled forward until the door opens enough to slide the drawet_ out. In some

cases, when you roll the refligeramr out,

you will need m move the refligerator

m the left or right as you roll it out.

Abouttheautomaticicemaker.

A newly-installed refrigerator may take 12to 24 hours to begin making ice.

]cemaker

Switch ]erArm

Ice Drawer

Pull the upper freezer sheff straight out to access the icemaker. Always be sure to replace the shelf. The shelf can be used for storage.

Automatic Icemaker

The icemaker will produce seven cubes per cycle--approximately 100-1,30 cubes

in a 24-hour pedod, depending on fleezer

comparmlent temperature, room

mmperamre, number of door openings and other use conditions.

If the refligerator is operated before the water connection is made to the icemake_,

set the power switch in the OFFposition.

_qlen the refligemtor has been connected

to the water suppl}; set the power switch to

the 0N position. The icemaker will fill wifll water when it

cools to 15°F (-10°C). A newly4nstalled

reflJgemtor m W take 12 m 24 horns m begin making ice cubes.

Throw away the first few batches of ice

to allow the water line to cleaL

Be sure nothing interferes with the sweep

of the feeler arm.

X_rhenfile bin fills to file level of file feeler

arm, file icemaker will stop producing ice. It is normal for several cubes m be joined

mgetheL If ice is not used flequently, old ice cubes

will become cloudy, tasm stole and shrink.

IceDrawer

Ice Storage Drawer

Toaccessice, pull the drawer forward.

Toremove the drawer, pull it smdght out and

lift it past the stop location.

Aboutthe ice and water dispenser.(onsome models) ge.com

On some mode/s

To Use the Dispenser

SpillShelf

Select CUBEDICE_, CRUSHEDICE

or WATER_.

Press the ,glass gently against the top of the

dispenser cradle.

The spill shelf is not self-draining. To

reduce water spotting, the shelf and its

grille shouM be cleaned regularly.

If no wateris dispensedwhen therefrigeratoris first installed,theremaybe air in thewaterline

system.Pressthedispenserarmforat least two minutesto removetrappedairfromthewater

line andtofill the watersystem.Toflushout impuritiesin the waterline, throwawaythe first

sixglassfulsof water. CAUTION:Neverputfingersoranyother

objectsinto theicecrusherdischargeopening.

Locking the Dispenser

@ Press the LOCKCONTROL

,__ padfor 3seconds to

:, unlock, press and

HOLD3SEeS hold the pad again

lock the dispenser and control panel. To

for 3 seconds.

Dispenser Light

This pad turns the night light in the dispenser on

and off: The light also comes on when the

LIGHT dispenser cradle is

pressed. If tiffs light burns out, it should be

replaced with a 6 watt

12 V maximum bulb.

QuickIce

@ _rhen you need ice

..... in a hurry, press this

pad to speed lap ice production. This will

QUICK ICE

Door Alarm

DOORALARM

increase ice production for the following

48 hours or until you press the pad again.

To set die alarm, press tiffs pad until die

indicator light comes on. This alarm will

sound if either door is open for more than

3 minums. The light goes out and the

beeping stops when you close the dooL

Important Facts About Your Dispenser

Do not add ice flom trays or bags to the storage draweL It may not crush or

dispense well.

Avoid overfilling glass Mill ice and use

of narrow glasses. Backed-up ice can jam the chum or cause the door in the chute

m freeze strut. If ice is blocking the clmm, poke it through with a wooden spoon.

Beverages and foods should not be quick-chilled in file ice storage draweL

Cans, bottles or food packages in the storage drawer may cause the icemaker

or attger to jam. To keep dispensed ice flom missing

the glass, put the ,glass close to, but not touching, the dispenser opening.

Some crushed ice may be dispensed even fllough you selected CUBEDICE.This

happens occasionally when a few cubes accidentally get direcmd m the cmsheL

AfYer crushed ice is dispensed, some water may drip flom the clmte.

Sometimes a small mound of snow will form on fl_e door in d_e ice chute. This

condition is nomml and usually occurs

when you have dispensed crushed ice

repeatedly: The snow Mll eventuMly evaporate.

Aboutthe ice and water dispenser.

Ice Storage Drawer on Dispenser Models

Toremove:

Set the icemaker power switch to the OFFposidon. Pull tlle drawer straight out

and then lift past the stop position.

Toreplace:

When replacing the drawe_, be sure to

press it fimdy into place. If it does not go

all the way back, remove it and romm the

drNe mechanism 1/4 turn. Then push the drawer back again.

Careand cleaning of therefrigerator.

i( ¸ : / (J

Dispenser drip area.

Cleaning the Outside

Thedispenserdriparea,(on some models)

beneath file glille, should be wiped dD_.Water left in this area mW leave deposits. Remove

the deposits by adding undilumd vinegar m

the well. Soak until the deposits disappear

or become loose enough m _Jnse away.

Thedispensercradle(on some models).

Before cleaning, lock file dispenser by

pressing and holding the LOCKCOIVTROt

pad for 3 seconds. Clean with warn1 wamr and baking soda solution--about

a tablespoon (15 ml) of baking soda to a quart (1 liter) ofwamL Rinse thoroughly and wipe dxT.

Thedoorhandlesandtrim.Clean with

a cloth dampened with soap}, wateL Dry with a soft cloth.

Drive Mechanism

Thestainlesssteelpanelsanddoorhandles

(on some models) can be cleaned Mttl a commercially available stainless steel cleaner such as Stainless Sted M(_ic'"

Stainless StealM(_ic is available at Ace, True

Value, Servismx; H1_I and other leading

stores. It is also available duougb GE Parts and Accessories, 800.626.2002. Order part

number _rX] OX] 5.

Do not use appliance wax or polish on the stainless steel.

Keep the outside clean, gripe Mtb a clean clod1 lighdy dampened Mill kitchen

appliance wax or mild liquid dish detergent. DU and polish wkh a clean, soft cloth.

Donotwipetherefrigeratorwithasoileddish clothor wet towel Thesemayleavea residue

thatcanerodethepaint.Donot usescouring pads,powderedcleaners,bleachorcleaners

containingbleachbecausetheseproductscan scratchandweakenthepaintfinish.

Cleaning the Inside

Tohelp prevent odors, leave an open box

of baking soda in the flesh food and fleezer compamnents.

Unplugtherefrigeratorbeforecleaning.If dds is not practical, wlJng excess moisane out of sponge or cloth when cleaning around

switches, lights or conuols.

Use warm wamr and baking soda solution-- about a tablespoon (15 ml) of baking soda

to a quart (1 liter) ofwateL Tiffs bodl cleans

and neutralizes odors. Rinse and wipe d_y.

Useof anycleaningsolution otherthanthat

which isrecommended,especiallythosethat

containpetroleumdistillates,can crackor damagetheinterioroftherefrigerator.

Avoidcleaningcoldglassshelveswith hotwater becausetheextremetemperaturedifference

maycausethemto break.Handleglassshelves carefully.Bumpingtemperedglasscancause it toshatter.

Donotwashany.plastic refrigeratorparts in

thedishwasher.

Behind the Refrigerator

ge.com

Be careflll when moving file refligemtor away from file wall. All Wpes of floor

coverings can be damaged, particularly cushioned coverings and fllose Mtb

embossed stnTaces.

Pull the reflq_gerator straight out and return

it to position by pushing it smdght in.

Moving the reflJgeramr in a side direction

m W result in damage m the floor covering or refligeratoL

Preparing for Vacation

For long vacations or absences, remove food and unplug file refligemtoL Clean

the interior with a baking soda solution of one tablespoon (15 ml) of baking soda m one quart (1 limr) ofwateL I,eave the

doo,s open.

Set the icemaker power switch to the OFFposifion and strut off the water supply

to the reflJgeratoL

Whenpushingtherefrigeratorback,makesure

youdon't roll overthepowercordor icemaker supplyline (onsomemodels).

If die mmperamre can drop below fleezing, have a qualified servicer drain the wamr

supply system (on some models) m prevent serious property damage due m flooding.

....Z??ii]ii]

Z?:_IIIIIIIII'II

iiiiiiii_iiiii{iiiiii_i_i_ii

_i'iiiiiLii_i_iii_ii,ii

t{i_iiiitiiii{ii_ii

Preparing to Move

Secure all loose items such as shelves and drawers by roping them securely in place

to prevent damage.

When using a hand track m move die

reflq_geramI;do not rest file flont or back of the refligeramr against the hand track.

This could damage the refligeramL Handle

only flom the sides of the refligeramL

Be sure the refrigerator stays in an upright

position during moving.

Replacingthe lightbulbs.

Setting either or both controls to 0 does not remove power to the light circuit.

_ _ Refrigerator Compartment--Upper Light

0 Unplug the refligeratoL

0 The bulb is located at file top of file

compartment, inside file dome light shield. To remove file shield, place your

Pocket

finger in file pocket at file back of file shield. Pull file shield forward and down.

Refrigerator Compartment--Lower Light

After replacing the bulb with an appliance bulb of the same or lower

wattage, replace the light shield.

Plug the refrigerator back in.

This light is located above the top drawer.

O Unplug the refrigeratoL 0 I,ift the light shield up and pull it out.

Freezer Compartment

Unplug the refl_igeratoL

Remove file shelf just above the light

shield. (The shelfMll be easier m remove if it is emptied fi_st.) On some

models, a screw at the mp of the light shield will need m be removed.

To remove file light shield, press in on

file sides, and lift up and out. On some models, lift the light shield up and pull

it out.

MYer replacing the bulb with an

appliance bulb of the same or lower

wattage, replace the shield.

Plug the refligerator back in.

Replace the bulb with an appliance bulb of the same or lower wattage,

and reinstall the light shield. When reinstalling the light shield, make sure the top robs snap securely

into place. Replace the screw (on some models).

O Reinstall the shelf and plug the

refligerator back in.

Dispenser

0 Unplug the reffigeratoL O The bulb is located on the

dispenser under the control panel. Remove the light bulb by turning

it counterclockwise.

0 Replace the bulb with a bulb of the

same size and wattage.

Plug the refligerator back in.

Installation

Refrigerator

Instructions

Questions? Call 800.GE.CARES (800.432.2737) or Visit our Website at: ge.com

In Canada, call 1.800.561.3344 or Visit our Website at: www.geappliances.ca

BEFORE YOU BEGIN

Read these instructions completely and carefully.

IMPORTANT - Savethese

instructions for local inspector's use.

• IMPORTANT - Observeall

governing codes and ordinances.

• Note to Installer- Be sure to leave these instructions with the Consumer.

• Note to Consumer- Keep these instructions for future reference.

• Skill level - Installation of this appliance requires basic mechanical skills.

• Completion time- Refrigerator Installation

30 minutes Water Line Installation

30 minutes

PREPARATION

WATER SUPPLY TO THE ICEMAKER

If the refrigerator has an icemaker, it will have to be connected to a cold water line. AGE

water supply kit (containing tubing, shutoff valve, fittings and instructions) is available at extra cost from your dealer, by visiting our Website at ge.com (in Canada at

www.geappliances.ca) or from Parts and

Accessories, 800.626.2002 (in Canada

1.800.661.1616).

TOOLS YOU WILL NEED

Models 23 & 25

• Proper installation is the responsibility of

the installer.

• Product failure due to improper installation is not covered under the Warranty.

If the refrigerator has already been installed, remove the base grille (see Step 2 in Moving

the Refrigerator), then skip to Step 5 in Installing the Refrigerator.

3/8" and 5/16" Socket 1/2" and 7/16" Wrench

Plastic Putty Knife

Phillips Head Screwdriver

Installation Instructions

MOVING THE REFRIGERATOR

ITI LOADING THE RERIGERATOR

ONTO A HAND TRUCK

Leave all tape and door pads on doors until the refrigerator is in its final location.

To move the refrigerator, use a padded

hand truck. Center the refrigerator on the hand truck and secure the strap around

the refrigerator. DO NOT OVERTIGHTEN THE STRAP.

If the refrigerator must go through any entrance that is less than 38" wide, the doors must be removed.

Proceed to Step 3.

DO NOT remove the handles.

If all entrances are more than 38" wide, skip to Installing

the Refrigerator.

131DISCONNECT THE WATER

COUPLING (on some models)

If the refrigerator has a water dispenser,

there is a water line from the cabinet into the bottom hinge on the freezer door that

must be disconnected. To disconnect, push in on the white collar

of the coupling and pull out the tubing.

White collar

121REMOVE THE BASE GRILLE

Remove the grille by removing the two Phillips head screws.

Bottom

freezer

hinge

Installation Instructions

[_] DISCONNECT THE POWER

COUPLING (on some models)

If the refrigerator has a water dispenser,

there is a power line (harness) from the cabinet into the bottom hinge on the

freezer door that must be disconnected. To disconnect, pull apart at the coupling.

[] DISCONNECT THE ELECTRICAL

CONNECTORS (on some models)

If the refrigerator has a refreshment center, there are electrical connectors

(harnesses) from the cabinet into the bottom hinge on the refrigerator door

that must be disconnected. To disconnect, pull apart each connector.

[] CLOSE THE FREEZER AND

REFRIGERATOR DOORS

171REMOVE THE FREEZER DOOR

[_] Remove the freezer door top hinge cover

by either squeezing it and pulling it up or by prying it off with a plastic putty knife.

[]

Remove the two 5/16" hex head screws, then lift the hinge straight up to free the hinge pin.

5/16" Hex Head

Bottom refrigerator

hinge

[]

Open the freezer door to 90.°

90 °

Installation Instructions

MOVING THE REFRIGERATOR (CONT.)

[] REMOVE THE

FREEZER DOOR (cont.)

[] As one person slowly lifts the freezer door

up and off the bottom hinge, the second person should carefully guide the water line and power line (harness) through the bottom hinge.

90°

['_ Set the door on a non-scratching surface

with the inside up.

[] REMOVE THE

REFRIGERATOR DOOR (cont.)

[] Remove the two 5/16" hex head screws,

then lift the hinge straight up to free the hinge pin.

5/16" Hex Head

[_] Open the refrigerator door to 90. °

i i

1-81REMOVE THE

REFRIGERATOR DOOR

[_] Remove the refrigerator door top hinge

cover by either squeezing it and pulling

it up or by prying it off with a plastic putty knife.

90 °

Installation Instructions

181REMOVE THE

REFRIGERATOR DOOR (cont.)

[] Lift the refrigerator door up and off the

bottom hinge.

If the refrigerator has a refreshment center, one person should slowly lift the

door up and off the bottom hinge and the second person should carefully guide the electrical lines (harnesses) through the

bottom hinge.

90°

[] REPLACING THE DOORS

To replace the doors, simply reverse steps 3 through 8.

However, please note the following:

• When lowering the doors onto the

bottom hinges, make sure the second person carefully guides the tube and harnesses through the holes in the hinges.

• When connecting the water line, make sure you insert the tubing all the way

to the mark.

Refreshment Center Models only

[] Set the door on a non-scratching surface

with the inside up.

Mark

• Do not pinch the tubing and harnesses

when placing the doors on the bottom

hinges.

• When connecting the power line and

the electrical lines (refreshment center

models only), be sure that the connectors are seated together fully.

Installation Instructions

INSTALLING THE REFRIGERATOR

REFRIGERATOR LOCATION

• Do not install the refrigerator where the temperature will go below 60°F (16°C)

because it will not run often enough to maintain proper temperatures.

• Do not install the refrigerator where the temperature will go above 100°F (37°C)

because it will not perform properly.

• Install it on a floor strong enough to support it fully loaded.

CLEARANCES

Allow the following clearances for ease of installation, proper air circulation and plumbing and electrical connections:

23' and 25'

Sides 1/8" (4 mm) Top 1" (25 mm)

Back 1" (25 mm)

Installation Instructions

ITI CONNECTING THE REFRIGERATOR

TO THE HOUSE WATER LINE

(icemaker and dispenser models)

A cold water supply is required for automatic icemaker and dispenser operation. If there is not a cold water supply, you will need to provide one. See "Installing the Water Line" section.

NOTES:

• Before making the connection to the refrigerator, be sure the refrigerator power cord is not plugged into the wall

outlet.

• If your refrigerator does not have a

water filter, we recommend installing

one if your water supply has sand or particles that could clog the screen of

the refrigerator's water valve. Install it

in the water line near the refrigerator. If using GE SmartConnect TM Refrigerator

Tubing Kit, you will need an additional tube (WX08X10002) to connect the filter.

Do not cut plastic tube to install filter.

[_] If you are using copper tubing, place a

compression nut and ferrule (sleeve) onto the end of the tubing coming from the

house cold water supply.

If you are using the GE SmartConnect TM tubing, the nuts are already assembled to

the tubing.

[_] If you are using copper tubing, insert

the end of the tubing into the refrigerator connection, at the back of the refrigerator, as far as possible. While holding the tubing, tighten the fitting.

If you are using GE SmartConnect TM tubing, insert the molded end of the

tubing into the refrigerator connection, at the back of the refrigerator, and tighten the compression nut until it is hand tight. Then tighten one additional turn with a wrench. Overtightening may cause leaks.

rc--] Fasten the tubing into the clamp provided

to hold it in position. You may need to pry open the clamp.

Tubing Clamp 1/4" Tubing

1/4"

Compression Nu

Ferrule (sleeve)

Refrigerator Connection

SmartConnect TMTubing

[] TURN ON THE WATER SUPPLY

Turn the water on at the shutoff valve (house water supply) and check for

any leaks.

[] PLUG IN THE REFRIGERATOR

Before plugging in the refrigerator, make sure the icemaker power switch is set to the OFF position.

See the grounding information attached to the power cord.

Installation Instructions

INSTALLING THE REFRIGERATOR (CONT.)

141PUT THE REFRIGERATOR

IN PLACE

Move the refrigerator to its final location.

[] LEVEL THE REFRIGERATOR

The refrigerator can be leveled by adjusting the rollers located near the

bottom hinges.

[] LEVEL THE DOORS

Adjust the refrigerator door to make the doors even at the top.

To align:

Using a 7/16" wrench, turn the door adjusting screw to the right to raise the door, to the left to lower it.

NOTE:

A nylon plug, imbedded in the threads of the pin, prevents the pin from turning

unless a wrench is used.

[]

After one or two turns of the wrench, open and close the refrigerator door and check the alignment at the top of the doors.

Doors should be even at top

Raise

Rollers have three purposes:

Rollers adjust so the door closes easily

when opened about halfway. (Raise the front about 5/8" [16 mm] from the floor.)

Rollers adjust so the refrigerator is

firmly positioned on the floor and does

not wobble. Rollers allow you to move the

refrigerator away from the wall for

cleaning.

To adjust the rollers on 23' and 25' models:

• Turn the roller II

adjusting screws S

clockwise to

raise the _.

refrigerator,

counterclockwise to lower it. Use a 3/8" hex socket

or wrench, or an adjustable

wrench.

Roller adjusting screw

Installation Instructions

171REPLACE THE BASE GRILLE

Replace the grille by installing the two Phillips head screws.

[] START THE ICEMAKER

Set the icemaker power switch to the ON position. The icemaker will not begin to operate until it reaches its operating temperature of 15°F (-9°C) or below. It will then begin operation automatically. It will take 2-3 days to fill the ice bin.

Power_" '-- .........!

switch

SET THE CONTROLS

Set the controls to the recommended setting.

I.ECOMME.OEOCO.T.O'SETT..OS]

0 °F IS RECOMMENDED 37 °F IS RECOMMENDED

Installation Instructions

INSTALLING THE WATER LINE (ICEMAKER &DISPENSERMODELS)

BEFORE YOU BEGIN

Recommended copper water supply kits are

WX8X2, WX8X3 or WX8X4, depending on the

amount of tubing you need. Approved plastic

water supply lines are GE SmartConnect TM

Refrigerator Tubing (WX08X10002,

WX08X10006, WX08X10015 and WX08X10025).

When connecting your refrigerator to a GE

Reverse Osmosis Water System, the only approved installation is with a GE RVKit. For other reverse osmosis water systems, follow

the manufacturer's recommendations.

If the water supply to the refrigerator is from a Reverse Osmosis Water Filtration System

AND the refrigerator also has a water filter,

use the refrigerator's filter bypass plug. Using

the refrigerator's water filtration cartridge in

conjunction with the RO filter can result in hollow ice cubes and slower water flow from

the water dispenser. This water line installation is not warranted

by the refrigerator or icemaker manufacturer. Follow these instructions carefully to minimize the risk of expensive water damage.

Water hammer (water banging in the pipes)

in house plumbing can cause damage to refrigerator parts and lead to water leakage or flooding. Call a qualified plumber to correct

water hammer before installing the water

supply line to the refrigerator.

To prevent burns and product damage, do not

hook up the water line to the hot water line. If you use your refrigerator before connecting

the water line, make sure the icemaker power

switch is in the OFF position. Do not install the icemaker tubing in areas

where temperatures fall below freezing. When using any electrical device (such as a

power drill) during installation, be sure the device is double insulated or grounded in a manner to prevent the hazard of electric shock, or is battery powered.

All installations must be in accordance with

local plumbing code requirements.

WHAT YOU WILL NEED

• Copper or GE SmartConnect TM Refrigerator Tubing kit, 1/4" outer diameter to connect the refrigerator to the water supply. If using copper, be sure both ends of the tubing are

cut square.

To determine how much tubing you need: measure the distance from the water valve on

the back of the refrigerator to the water supply pipe. Then add 8' (2.4 m). Be sure there is sufficient extra tubing (about 8' [2.4 m]

coiled into 3 turns of about 10" [25 cm] diameter) to allow the refrigerator to move

out from the wall after installation. GE SmartConnect TM Refrigerator Tubing Kits

are available in the following lengths: 2' (0.6 m) -WX08X10002 6' (1.8 m) -WX08X10006

15' (4.6 m) -WX08X10015

25' (7.6 m) -WX08X10025

Be sure that the kit you select allows at least

8' (2.4 m) as described above.

Installation Instructions

WHAT YOU WILL NEED (CONT.)

NOTE: The only GE approved plastic tubing is that supplied in GE SmartConnect TM Refrigerator Tubing kits. Do not use any other plastic water supply line because the line is under pressure at all times. Certain

types of plastic will crack or rupture with age

and cause water damage to your home.

• AGE water supply kit (containing tubing, shutoff valve and fittings listed below) is available at extra cost from your dealer or

from Parts and Accessories, 800.626.2002

(in Canada 1.800.661.1616).

• A cold water supply. The water pressure must be between 20 and 120 p.s.i. (1.4-8.1 bar).

• Power drill.

• I12" or adjustable wrench.

• Straight and Phillips blade screwdriver.

Install the shutoff valve on the nearest

frequently used drinking water line.

[TI SHUT OFF THE MAIN WATER

SUPPLY

Turn on the nearest faucet long enough to clear the line of water.

[] CHOOSE THE VALVE LOCATION

Choose a location for the valve that is

easily accessible. It is best to connect into

the side of a vertical water pipe. When it is

necessary to connect into a horizontal water pipe, make the connection to the top or side, rather than at the bottom, to avoid drawing off any sediment from the water pipe.

• Two 1/4" outer diameter compression nuts and 2 ferrules (sleeves)into connect the

copper tubing to the shutoff valve and the refrigerator water valve.

• If you are using a GE SmartConnect TM Refrigerator Tubing kit, the necessary

fittings are preassembled to the tubing.

• If your existing copper water line has a

flared fitting at the end, you will need an

adapter (available at plumbing supply stores) to connect the water line to the

refrigerator OR you can cut off the flared

fitting with a tube cutter and then use a

compression fitting. Do not cut formed end

from GE SmartConnect TM Refrigerator tubing.

• Shutoff valve to connect to the cold water line. The shutoff valve should have a water inlet with a minimum inside diameter of

5/32" at the point of connection to the COLD

WATER LINE. Saddle-type shutoff valves are

included in many water supply kits. Before purchasing, make sure a saddle-type valve complies with your local plumbing codes.

[] DRILL THE HOLE FOR THE VALVE

Drill a 1/4" hole in the water pipe (even if using a self-piercing valve), using a sharp bit. Remove any burrs resulting from drilling the hole in the pipe.

Take care not to allow water to drain into the drill.

Failure to drill a 1/4" hole may result in reduced ice production or smaller cubes.

Installation Instructions

INSTALLING THE WATER LINE (CONT.)

[] FASTEN THE SHUTOFF VALVE

Fasten the shutoff valve to the cold water

pipe with the pipe clamp.

Pipe Clamp

Saddle-Type Shutoff Valve

NOTE: Commonwealth of Massachusetts Plumbing Codes 248CMR shall be adhered

to. Saddle valves are illegal and use is not permitted in Massachusetts. Consult with your licensed plumber.

Vertical Cold Water Pipe

[] TIGHTEN THE PIPE CLAMP

Tighten the clamp screws until the sealing washer begins to swell.

NOTE: Do not overtighten or you may crush the tubing.

Washer

Pipe

Clamp Screw

Inlet End

171CONNECT THE TUBING

TO THE VALVE

Place the compression nut and ferrule (sleeve) for copper tubing onto the end of the tubing and connect it to the

shutoff valve.

Make sure the tubing is fully inserted into the valve. Tighten the compression nut securely.

For plastic tubing from a GE

SmartConnect TM Refrigerator Tubing kit,

insert the molded end of the tubing into

the shutoff valve and tighten compression

nut until it is hand tight, then tighten one additional turn with a wrench.

Overtightening may cause leaks.

Saddle-Type Shutoff Valve

_t / SmartConneet TM

,. _ Tubing

Packing Nut

Outlet Valve

NOTE: Commonwealth of Massachusetts Plumbing Codes 248CMR shall be adhered

to. Saddle valves are illegal and use is not

permitted in Massachusetts. Consult with

your licensed plumber.

Ferrule (sleeve)

Compression Nut

161ROUTE THE TUBING

Route the tubing between the cold water line and the refrigerator.

Route the tubing through a hole drilled in the wall or floor (behind the refrigerator or adjacent base cabinet) as close to the wall as possible.

NOTE: Be sure there is sufficient extra

tubing (about 8' [2.4 m] coiled into 3 turns

of about 10" [25 cm] diameter) to allow the refrigerator to move out from the wall after

installation.

[] FLUSH OUT THE TUBING

Turn the main water supply on and flush

out the tubing until the water is clear. Shut the water off at the water valve after

about one quart (1 liter) of water has been

flushed through the tubing.

To complete the installation of the refrigerator,

go back to Step 1 in Installing the Refrigerator.

Normal operatingsounds, geoom

Newer refrigerators sound different from older refrigerators. Modem refrigerators have more features and use newer

technology.

Do you hear what I hear? These sounds are normal.

HUMMM...

--WHOOSH...

• The new high efficiency compressor may run faster and longer than your old refligerator and you may

hear a high-pitched hum or pulsating sound while it is operating.

• Sometimes the refligemtor runs for an extended period, especially when the doors are opened fiequently. This

means flint the Frost GuardTM feature is working to prevent fleezer burn and improve food preservation.

• You mW hear a whooshing sound when the doors close. This is due to pressure equalizing within the refligeramL

CLICKS, POPS,

CRACKS and CHIRPS

• You may hear cracking or popping sounds when the refligerator is first plugged in. This happens as the

refrigerator cools to the correct temperature.

• Electronic dampers click open and closed to provide optimal cooling and energy savings.

• The compressor may cause a clicking or chirping sound when attempting to restart (this could take

tap to 5 minutes).

• The electronic conuol board may cause a clicking sound when relays activate to control refligerator

components.

• Expansion and conuacdon of cooling coils during and after deflost can cause a cracking or popping

sotlnd.

On models with an icemaket; after an icemaking cycle, you may hear the ice cubes dropping into

the ice bucket.

WHIRl

• You may hear the fans spinning at high speeds. This happens when the refligerator is first plugged

in, when the doors are opened flequenfly or when a large amount of food is added to the refrigerator

or fleezer compamnents. The fans are helping to maintain the correct temperatures.

• If either door is open for over 3 minutes, you may hear the fans come on in order to cool the light

bulbs.

The fans change speeds in order to provide optimal cooling and energy savings.

WATERSOUNDS

• The flow of refligerant through the fleezer cooling coils may make a gurgling noise like boiling watm.

• X_rater dropping on the deflost heater can cause a sizzling, popping or buzzing sound during the

deflost cycle.

• A water dripping noise may occur during the deflost cycle as ice melts flom the evaporator and flows into

the drain pan.

• Closing the door m W cause a gmgling sound due to pressure equalization.

Beforeyoucall forservice...

i_ii{iiii!iiiiiii!ii

Troubleshooting -tips Save time and money! Review the charts on the following pages first and you may not need to call for service.

Possible Causes What ToDo

Refrigerator does not Refrigerator in defrost cycle. * \_rait about 30 minutes for deflost cycle to end. operate Either or both controls set to O. * Set the controls to a temperature setting.

Refrigerator is unplugged. * Push the plug completely into the outlet. The fuse is blown/circuit • Replace fl_se o1 reset the breakeL

breaker is tripped. Refrigerator is in the showroom • Unplug the refligerator and plug it back in.

mode.

Vibration or rattling Rollers need adjusting. * See Rollers.

(slight vibration

is normal)

Motor operates for Normal when refrigerator * \_rait 24 hours for the refligerator to completely long periods or cycles is first plugged in. cool down.

on and offfrequently. (Modern refrigerators Often occurs when large " This is hernial.

with more storage

space and a larger placed in refrigerator.

freezer require more Door left open. • Check to see if package is hoMing door open.

operating time. They

start and stop often Hot weather or frequent • This is hernial. to maintain even door openings.

temperatures.! Temperature controls • See About the controls.

Refrigerator orfreezer Temperature control not set • See About the controls. compartment too warm cold enough.

Frostor ice crystals Door left open. * Gheck to see if package is holding door open. on frozen food

(frost within package is normal) door openings.

amotmts of food are

set at the coldest

setting.

Warm weather or frequent • Set the temperature control one step coldeL

door openings. See About the controls. Door left open. • Check to see if package is hoMing door open.

Too frequent or too long

Divider between Automatic energy saver • This helps prevent condensation on the outside. refrigerator and freezer system circulates warm

compartments liquid arotmd front edge

feels warm of freezer compartment.

Automaticicemaker Icemaker power switch • Set the power switch to the ONposition.

does not work is in the OFFposition.

Water supply turned off or • See Installing the water line.

m m

not connected.

Freezer compartment • \_rait 24 hours for the refligerator to completely too warm. cool down.

Piled up cubes in the storage • 1,evel cubes by hand. bin cause the icemaker

to shut off.

Ice cubes stuck in icemaker.

• Turn off the icemake_; remove cubes and mrn the icemaker back on.

+ 82 hidden pages