GE GSHF9NGYACWW, GSHF9NGYACBB Owner’s Manual

GEAppliances.com

Safety Instructions ........... 2-3

Operating Instructions

Automatic lcemoker .............. 11

Care and Cleaning ............ 13, 14

Crispers and Pans ............ 10

Ice and Water Dispenser ........ 12, 13

Refrigerator Doors ................. 9

Replacing the Light Bulbs ......... 1S

Shelves and Bins ................. 7, 8

Temperature Controls ............ 4

TurboCoof ..................... 4

Water Filter .................... 5, 6

Installation Instructions

Installing the Refrigerator . , 21-24

Moving the Refrigerator .......... 17-20

Preparing to Install

the Refrigerator ............. 16

Water Line Installation .......... 25-27

Troubleshooting Tips , , ,28-31

Normat Operating Sounds ........ 28

Consumer Support

Consumer Support .......... Back Cover

Performance Data Sheet , ,32, 33 State of California Water

Treatment Device Certificate 34, 35

Warrantg (Canadian} .......... 36

Warrantg (U S) .......... 37

Models 22, 23, 25, 25, 27 and 29

CSte h C6te

R frig rateurs

La section fran_aise commence 6 la page 38

Ladoa Lado

Refrigeradores

La secci6n enespafiol empieza en la p@ina 74

Write the model and serial numbers

here: Model #

Serial #

Findthese numbers ona label inside the refrigerator compartment at the

top on the right side

200D8074P037 49-50587 02-09 JR

IMPORTANT SAFETYINFORMATION.

_,_ _L:, ,__, : • L i :•

_ii__,i :i:_i_::i

v A

w ° .

vn trt

READ ALL INSTRUCTIONS BEFOREUSING.

HIIIIIIIIIIIIII,IIiH, iii .......................

A WARNING!

Use this appliance onfg for its intended purpose as described in this Owner's Manual,

SAFETYPRECAUTIONS

When using electrical appliances, basic safet_lprecautions should be followed, including the following:

Thisrefligerator must be properlg installed and located in accordance with theInstallation

Instructionsbeforeit is used Donot allow childrento climb,stand or hang

on the shelvesinthe refligerator.Theycould damagethe refrigeratorand seriously injure

themselves

Do not touch the cold surfaces in the freezer compartment when hands are damp or wet

Skinmay stick to these extremely cold surfaces. Do not store or use gasoline or other flammable

vapors and liquids in the vicinity of this or any other appliance

ii:¸•

In refrigerators with automatic icemakers, avoid contact with the moving parts of the ejector mechanism or with the heating element

located on the bottom of the icemaker. Do not place fingers or hands on the automatic

icemaking mechanism while the refrigerator is plugged in

Keepfingersout of the "pinchpoint" areas; clearancesbetween the doorsand between

the doorsand cabinet are necessarilysmall Becareful closingdoorswhen childrenare in the area

:: Unplug the refligerator beforecleaning and making

repairs NOTE:We strongly recommendthat any servicing

beperformed b_laqualifiedindividual

::::::Do not refreezefrozenfoodswhich have

thawed completely

NOTE:Turning the refrigerator off vio the controls on the touch panel does not shut off dectricat power to the refrigerator.

0 0

A ,

tt. i

u'l

GEAppliances,:,com

................ OAr G::ER:RISK OF CHILD

ENTRAPMENT

PROPERDISPOSALOF THEREFRIGERATOR

Childentrapment andsuffocation arenot problems ofthe past Junkedor abandoned refrigeratorsare stilldangerous evenifthey willsit for '_iustafew days" Ifyou aregetting ridof your old refrigerator_ pleasefollow the instructionsbelow to help prevent

accidents

Before You ThrowAway Your Old Refrigerator or Freezer:

_:::Takeoff the doors :::::Leavethe shelvesin place so that childrenmay not

easilyclimb inside

Refrigerants

All refrigeration products contain refrigerants,which

under federal law must be removed prior to product

disposal If gou are getting rid of an old refrigeration

product, check with the company handling the

disposal about what to do

i!::!..........USEOF EXTENSIONCORDS

Because of potentia! safety hazards under certain conditions we strongtg recommend against the use

dan extension cord

However,if you must useon extensioncord.it is absolutely necessarythat it be o UL-listed(inthe UnitedStates} or e CSA-listed(inCanada}.3-wiregrounding type applianceextension cord having a grounding type plug and outlet and that the electrical rating of the cord be 15amperes(minimum}and 120volts

v,* lJ,_

\ll S

A WARNING!

HOW TOCONNECTELECTRICITY

Do not, under ang circumstances, cut or remove the third (ground) prong from the power cord Forpersonal safety, this appliance must be properlg grounded

Thepower cord of thisappliance is equipped with o 3-prong (grounding)plugwhich mates with o standard5-prong (grounding}wa!loutlet to minimizethe possibilityofelectric shock hazard from this appliance

Havethewall outlet and circuitcheckedby a qualified electricianto make surethe outlet isproperly grounded

ifthe outlet is a standard 2-prong outlet, itis your personalresponsibilityand obligation to hoveit replaced with a properly grounded

3-prong wall outlet Therefrigerator shouldalwagsbe plugged intoits

own individualelectricaloutlet which hasovoltage rating that matchesthe rating plate.

Thisprovidesthe bestperformance end alsoprevents overloadinghousewiring circuitswhich couldcausea

firehazard from overheatedwires

Never unplug your refrigerator by pulling on the power cord Always grip plug firmly and pull straight out from the outlet,

Repairor replaceimmediately allpower cordsthat havebecomefrayed or otherwisedamaged Donot usea cordthat shows cracksor abrasion damage along its lengthor at eitherend

Whenmoving the refrigeratorawag from thewall, be carefulnot to rolloveror damage the power cord

v A

0 0

READAND FOLLOWTHISSAFETYINFORtVlATIONCAREFULLY, SAVETHESEINSTRUCTIONS

About the temperature controls.

Not of! features are on all models

l,e

Gu,boq

larm_

LCooLj

:_:_i¢_(:::i:_i_ i:i/:i_i::_•:ii_:/:!:

_ _: "L _ • :

v A

t.T m 1"i,_

0 0

O_F is Recammended 37_F is. Recommer_ded

0. ® ® • •

Hold 3 Seconds to Reset Hold 3 5econds

Thetemperaturecontrolsarepresetin thefactoryat37°FfortherefrigeratorcompartmentandO°Fforthe

freezercompartmentAllow24hoursforthetemperatureto stabilizetotilepresetrecommendedsettings

ThetemperaturecontrolscbndisplayboththeSETtemperatureaswellastheactualtemperatureinthe

refrigeratorandfreezer,TireactualtemperaturemayvaryslightlyfromtheSETtemperaturebasedon usageandoperatingenvironment

Onsamemodels,settingbothcontrolstothewarmestsettinguntilthedisplayflashes[off)willstop coatinginboththefreezerandrefrigeratorcompartments

i::: Onothermodels,settingeithercontroltothewarmestsettinguntilthedisplayflashesloft)willstop

thecoolingtothefreezerandrefrigerator. NOTE:Turningtherefrigeratoroffvia thecontrolsonthetouchponddoesnotshutoffeleddcalpower

totherefrigerator

NOTE:Therefrigeratorisshippedwithprotectivefilmcoveringthetemperaturecontrolstfthisfilmwas notremovedduringinstotfotionremoveit now

Performance Air Flow System

ThePerformanceAir-FlowSystemisdesignedto

maximizetemperaturecontrolintherefrigerator andfreezercompartments.Thisuniquespecial

featureconsistsoftile AirToweralongthe back

walloftherefrigeratorandtheAirTunnelonthe

bottomportionofthefreezerrearwallPtacing foodinfrontof thelouversonthesecomponents

About TurboCool:" (on some models}

will not affect performance Although the Air Tower andthe AirTunnelcon beremoved, doing so will

affect temperature performance (Forremoval k_structions,on-line contact us atgecam or

coil800GECARESInCanada,contact usat geappliancesca or call 1800 56t 33/44}

tt.

Gurbo

k coo,_J

How it Works

TurboCoolrapidlycoolstherefrigerator compartmentinordertomorequicklycoolfoods.

UseTurboCoolwhenaddingalargeamount

offoodtotherefrigeratorcomportment,putting awayfoodsaftertheyhavebeensittingoutat

roomtemperatureorwhenputtingawaywarm leftovers.Itcanalsobeusediftherefrigeratorhas

beenwithoutpowerforanextendedperiod

Onceactivatedthecompressorwillturnon immediatelyandthefanswiltcycleonand offathighspeedas neededforeighthours Thecompressorwillcontinuetorununtilthe refrigeratorcompartmentcoolstoapproximately

34°F(1°C1,thenitwillcycleonandofftomaintain thissettingAfter8hour&orifTurbaCoolis

pressedagain,therefrigeratorcompartment

wi! returntotheorgna settng

HowtoUse

PressTurboCoolTheTurboCooltemperature

displaywillshowTcendtheLEDwillbeactivated AfterTurboCooliscomplete,theTurboCool

indicatortightwillgoout NOTES:Therefrigeratortemperaturecannotbe

changedduringTurboCool Thefreezertemperatureisnataffected

duringTurboCao/ Whenopeningtherefrigeratordoor

duringTurboCool.thefanswillcontinue toruniftheyhavecycledon

About the water filter, tonsomemodels)

GEAppliances.com

i,,111 ii ii I iiiiii

Water Filter Cartridge

Thewater filter cartridge islocatedin the backupper right cornerof the refrigeratorcomportment

When to Replace the Filter on Models Without

a Replacement Indicator Light

Thefilter cartridge should bereplaced everg sixmonths or earlierif theflow ofwater to the waterdispenseror icemaker

decreases

Removing the Filter Cartridge

If gou are replacingthe cartridge,first removetheold one bg slowlgturning it to the left. Do not pulldown on the

cartridge A smallamount of water mag dripdown

Installing the Filter Cartridge

0 if gou arereplacinga SmartWatercartridgewith

an adapter,it must be removedbeforeinstallingthe cartridge To removethe adapter,turn it tothe left

about 1/4 turn

O Siowlgturn it to the rightuntil the filter cartridge stops

DONOTOVERTIGHTEN,As gouturn the cartridge, it will

automaticallg raise itself into position Thecartridge will move about 1/2 turn

CanridgeHolder

Runwater from the dispenserfor 3 minutes(about

1-1/2galions)to clearthe sgstemand prevent sputtering

Pressandhold the WATERFILTERpad tonsome models) on the dispenserfor 3 seconds

"teLJ

Hold 3 seconds to Reset

NOTE:A newlginstalledwater filter cartridge mag cause

water to spurt from thedispenser.

:_,/i_:? _i _::

:A L_:I"_-_, _::

XL :L_?_:C: :

v,F irl

With Adapter Wilhou[ Adapter

fappe_rancemayvary)

On modelswithout a replacementindicator light,apptg the month and gearstickerto the newcartridge to remind you to replacethe filter in six months,

_) Fillthe replacementcartridge withwater fromthe top to

allowfor betterflow from thedispenserimmediatelgafter installation

O Lineup thearrow on the cartridge and the cartridge

holder.Placethetop of the new cartridge up inside theholder`Do nat push it up into the holder.

Filter Bypass Plug

Youmust usethe filter bgpassplug when areplacementfilter cartridge is not available Thedispenserand the icemaker will not operatewithout the filter or filter bgpassplug

FiRer_ Bypass _)w,,_

Plug

Smarf#$gter

tf gou havequestions-visit ourWebsiteat GEAppliances,com or call 1.800GECARES11800/4322737)

Replacementfilters: Toorder additional filter cartridges in the United States,

visit our Websiteat GEAppliances.com,or call GEParts and

Accessories,800.5262002.

Filter Hodel MSWF

Customersin Canadashould consult the gellow pages for the nearestHabe ServiceCenter.

g,)

0 0

:::t"

About the water filter. (on some models) (cont.)

On some models Water" Niter Cartridge

Thewater fiitercartridge is located in the beckupper right cornerof the refrigeratorcomportment

When to Replace the Niter on Models Without a Replacement Indicator Light

Thefilter cartridgeshould be replacedeverysix months or earlierifthe flow of water tothe water dispenseror

icemakerdecreases

Removing the Filter Cartridge

Ifyou are replacingthecartridge first removetheold

one by slowly turning it to the left Do not pulldown on the cartridge Asmell amountof water maydrip down

Installing the Filter Cartridge

If youare replacinga SmartWatercartridge with an adopter,it must be removedbeforeinstalling

the cartridge Toremove the adapter,turn it

tothe left about 1/4turn.

O Slowlyturn it to the right until the filter cartridge stops

DONOTOVERTIGHTEN.Asyou turn the cartridge, it will automaticallyraise itself into position Thecartridge will

moveabout 1/2 turn

O Runwater from the dispenserfor 3 minutes (about 1-t/2

gallons)to clear the system and preventsputtering Pressand holdthe WATERFILTERpad (onsome models)

on the dispenserfor 3 seconds

"teLJ

Hold 3 secondsto Reset

NOTE:A newlyinstalledwater filter cartridge may cause water' to spurt from the dispenser.

With Adapter Without Adapter

(appearance may vary)

On modelswithout a replacementindicatorlight,

applg the month and year stickerto the new cartridge

to remind you to replacethe filter insix months.

Fillthe replacement cartridge with water from the tap to

allow for better flow from the dispenserimmediatelLjafter installation

Lineup the arrow on the cartridgeand the cartridge

holder PIacethe top of the new cartridge up insidethe holder_Do not push it up into the holder

Filter Bgpass Plug

Youmustusethe filterbypassplug when a replacementfilter cartridge is not available.Thedispenserand the icemakerwifl not operatewithout the filteror filter bypassplug

Bypass _ Plug

u n i

Stoat:Water

If you have questions-visit our Website at GEApptiances cam,

or call :L800GE CARES(t 800.432 27371

Replacement filters: To order additional filter cartridges in the United States,

visff our Webs!re at GEAppfiances.com, or call GE Parts and Accessories, 800.626°2002.

Filter Model HWF Customers in Canada should consult the yellow pages

for the nearest Habe Service Center:

About the shelvesand bins.

Not all features are on all models,

Refrigerator Door Bins and Freezer Door Tilt-Out Bins Large Bins

Thelarger refrigerator door binsand freezer tilt-out door binsare adjustable

Toremove: Lift the front of the bin straight

up. then lift up and out

To replace or relocate: Engage the back side of the bin inthe molded supports of the door,

Then push down on the front of the bin Bin wil!tack in place

SmallBins Toremove: Liftthe front of thebin straight up

thenout Toreplace: Positionthebin abovethe

Freezerbin

rectangularmoldedsupportson the door. Thenslidethe bin down ontothe support to lockit in place

GEAppliances,com

Thesnuggerhelpsprevent tipping spilling

or sliding of small itemsstoredonthe door shelf Placea finger on eithersideof the snuggernearthe rear and move it beck

and forth tofit gour needs

JJnt_J_ulunl_l_l n

CAUTION:

Onmodelswith an

ice chute inside the top freezer door bin.

be careful when placing items in the

bin Makesurethat itemsdonot block or fall into the ice chute

Freezer till-out bin

Pless tab and pull shell forward Io romove

Slide-Out Spillproof Shelf

Theslide-outspillproofshelfallows gou to reachitems storedbehind others The

specialedgesoredesignedto helpprevent spillsfrom dripping to lowershelves,

Toremove:

Slidethe shelfout until itreachesthe stop. then pressdown on the tab and slidethe shelf

straight out

Toreplace or relocate:

Linethe shelf up with the supports andslide

it intoplace Theshelfcan be repositioned when the door isat 90°or more To reposition the shelf,slidethe shelfpast the stopsand angle downward Slideshelfdown to the desiredposition,lineup with the supports and slide into place

Hake sure gou push the shelves all the wag back in before gou close the door

About the shelves and bins. rcontJ

Not all features are on all models

quickSpace'* Shelf (onsomemodels)

Thisshelfsplitsin half and sIidesunder itself

forstorage of tallitems on the shelf beIow

Thisshetfcan be removedand replaced

or-relocatedjust likeSlide-OutSpiltproof Shelves.

Freezer Baskets

Onsome models,this shelf cannot be used in the lowest position

Toremove slideoutto thestopposition lift the front past the stop position and

slideout.

Toremove, push the basket all theway to the backofthe freezer.Liftup until theback pinsaredisengaged Liftthe entirebasket up and pullout,

Slide-Out Freezer Shelves

Toremove, slideout tothe stopposition, lift the front pastthe stop position,andslide outfrom rib

Fixed Freezer Shelves Toremove, lift the shelfup at the left sideand

then bring the shelfout

Make sure gou push the basketsatt the way back in before you close the door:

Hake sure you push the basketsall the

wag back in beforegou close the door

Make sure gou push the shelvesall the wag back in before gou close the door

NOTEFORDISPENSERMODELS:In order

totake fulladvantageof the tilt-out icebin [onsome models[ only storeitems on the

shelfbelowthe icebin that are no taller than thelowest point on the bin

Door Wine/Beverage Rack (onsome models)

Thisrock holds up to 5cans or one bottle ofwine

Therack hangsfrom thesides of thedairy bin

Toremove:

O Emptythewine/beverage rack 0 Holdingthe bottom of the dairy bin.

lift the fiontstraight up,then lift up and out

O Todetach the rack from the dairy bin,

pull the rack'ssidewires out of the holes on each side of the dairy bin

Toreplace:

Reattachthe rackto the sidesof the bin Engagetheback side of the bin in

the moldedsupports on the door. Thenpush down on the front of

the bin The binwill lockinto place

About the refrigerator doors.

Refrigerator Doors

The refrigerator doors mag feel different

than the ones you ore used to. The special door opening/closing feature makes sure the doors close alI the wag and are

securelg sealed When opening and closing the door, you

wil! notice a stop position if the door is opened past this stop point, the door will

remain open to allow gou to goadand unload food more easiig When the door

is onlg portialtg open. it ,will outomaticallg close

Whenthe doorisonly partiallyopen. il wil; automaticallyclose

Beyondthisslop lhe doorwill stayopen

Door Alignment

Ifdoors ore uneven, adjust the refrigerator door.

O Usinga 7/16" socketwrench,turn the

door adjustingscrew to the right to raisethe door; to the left, to lower it.

(Anylonplug.imbedded in the threads of thepin, preventsthe pin from turning unlesso wrench isused}

GEAppliances.com

Theresistancegou feetat thestop

positionwill be reducedasthe door isloadedwith food

O After oneor twoturns ofthe wrench.

openand closethe refrigeratordoor and check the alignment at thetop

of the doors

_J r_

0 0

About the crispers and pans.

Not all features are on a!! models

Fruit and Vegetable Crispers

Excesswaterthat magaccumulate in the bottom of the drawersshouldbe wiped dry

Onsome models, the bottom drawer has fullextensionslidesthat alfowfull access

tothe drawer

HI _ LO

AdJustable Humidity Crispers

Slidethe control afl the wag to the HIsetting to providehigh humiditg recommended for

mostvegetables

Convertible Dell Pan fan some models] Theconvertible deli pan has its owncold air

duct to allow a stream ofcoldair from the fleezer compartment or refrigerator

compartment to flow to the pan

The variable temperature control regulates the air flow from the Climate Keeper Air

Tower.

Aboutcrispe r removal.

Not all features are on all models

Slidethe controi oil thewag to the LO setting toprovide lower humiditg levels

recommendedfor most fruits

Setthe control to thecoldest setting to store freshmeats

Set the contmi to cold to convert the pan

to normal refrigerator temperature and

provide extra vegetable storage space The

cold air duct is turned off Variable settings between these extremes can be selected

Crisper Removal

Crisperscan eas{igbe removedbg puiiingthe drawerstraight out and lifting the drawer up

andover the stop location

Ifthe door prevents goufrom taking out thedrawers,first trg to removethe door bins

ifthis does not offer enough clearance the refrigeratorwill needto be roiledforward

until thedoor opensenough to slidethe drawers out Insome cases,when gou rolt

the refrigeratorout, gou will needto move the refrigeratorto the left or rightasgou roll

it out

About the automatic icemaker.

A newlg installed refrigerator may take 12 to 24 hours to begin making ice

Automatic icemaker

GEAppliances.com

iii iii [11 ii ii ii ii ii/,11111II II ii ii ij i,j/i, i/i _11

Powsr

Switd_

Gi'88ri

PowerLight FeelerA.n

Models without a shelf

above the ice bin

To access ice end reach the

icemaker power switch:

Icemaker

The icemuker will produce seven cubes

per cgcle-appro×imotelg 100-130cubes

in a 24-hour period, depending on freezer compartment temperature, room temperature, number of door openings

and other use conditions See below for how to access ice and reach

the power switch on dispenser models If the refrigerator is operated before the

water connection ismade to the icemaker, set the power switch in the 0 (off/position

When the refrigerator has been connected to the water supplg, set timepower switch to the

I ton) position

Theicemokerwillfillwith waterwhen itcools to 15°F(-IO°C}Anewlginstalledrefrigerator

maLjtake12to24hourstobeginmakingice cubes

Youwill heara buzzingsoundeachtime

theicemaker fillswith water.

Accessing Ice and Reaching the Power Switch on Dispenser

Models Thereare two types of ice storage bins

on dispensermodels, Onehasa shelfabove

the bin,the other does not

Throwowag the firstfew batches of ice to allow thewater lineto clear,

Besurenothing interfereswith thesweep

of thefeeler arm

When the bin fills to the level of the feeler arm. the icemuker will stop producing ice

Itis normal for several cubes to be joined

together,

If ice is not usedfrequentlg,old ice cubes willbecome cloudg,taste stale end shrink.

NOTE:In homeswith lower-than-average water pressure,you may hearthe icemaker cyclemuttiptetimes when makingone batch

ofice

Hodels with a shelf

above the ice bin

_. O"

_: :( Ji?L >:_

.:. ,-<. :,

://:/-14 _j::

;<7/_ ,::_m

z_ % t :: :>: q_

:x : :L:_:-A :-

i_/ L _ z_,_,/_

i .

o Lift the bin. tl_enpull it

forward until the bin stops

O Lewer the bin to access ice

or reach the power switch

NOTE:In orderto take full

advantage of the tflt_out ice bin,

on0 store items on the shelf below

the ice bin that are no taller than the lowest point on the bin

Specialnote about dispenser models without a shelfabove the icebin:

Thesemodelshavee tilt-out ice bin. Thebincan be tiltedout asshown in the illustrations,andit will hold itself

up while goutake iceout or turn the icemokerpower switch on and off Besureto put the bin beck in place beforedosing the door.

To restore gour icelevelfrom an emptg

bucket stage,the following steps are recommended:

O 12hoursafter the first botch of ice

hasfallen into the bin,dispense 3to 4 cubes

After an additional 6 hours, dispense 3 to 4 cubes again

These steps will restore t.,Jourice Ievei

in the shortest amount of time

To access ice.pull the bin forward

Toreach the power switch, pull the shelfstraight out Always be sure to

replace the shelf

0 0

Itl

' O

;/ i:_::!: I::

i:,i!?:i?ii

:-: L_.: ¸ ::

:XI:: _:(::!i!::

!.- 11_

About the ice and water dispenser. (on somemodels)

,,,,,,,,,,,,,,,,,, ........................................... ,,,,, ,,, ,

To Use the Dispenser

SpillSherf

SetectCOBEO,CE cRus.ED,CE

or WATER_. Pressthe glassgentlgagainst the top of the

dispensercradle

Thespillshelf isnot self-draining Toreduce water spotting,the shelf and its grilleshould

becleanedregularlg,

finD water is dispensed when the refrigerator is first installed there may be air in the water line sgstem Press the dispenser arm far at least two minutes to remove trapped air from the water fine end to fill the water sgstem To flush out

impurities in the water line, throw uwag the first six glassfuls of water

CAUTION: Never put fingers or ang other objects into the ice crusher discharge

opening

Locking the Dispenser

PresstheLock Controls

pad for3 secondsto lock the dispenserand canboI panel To unlock press

ntro_ll

Hold 3 Seconds

and hold the pod again for 3 seconds

Dispenser Light

igh andoff Thelight also

Door Alarm tansomemodels)

L2U°r

Thispad turnsthe night

comeson when the dispenser-cradleis

pressed If thislight burns out, it should be replaced

with o 6 watt 12V

maximum bulb

Toset the alarm. pressthis pad until the

indicator light comes on Thisalarm wilt sound if

eitherdoor isopen for more than 3 minutes

Thelight goesout and the beepingstopswhen

gou closethe door,

Important Facts About Your Dispenser

0 0

Donot add icefrom trags or bags to the storagedrawer:It mag nat crushor dispensewetl

Avoidoverfillingglasswith iceand use ofnarrow glasses Backed-upice canjam

thechute or causethedoor inthe chute to

freezeshut If ice isblockingthechute,poke

itthroughwith a wooden spoon

Beveragesandfoods shouldnat be quick-chilledin the icestoragedrawer, Cans.bottlesor food packages inthe storagedrawer mag causethe icemaker or auger tojam

i::::Tokeepdispensedicefrom missing

theglass,put theglass closeto,but not touching,the dispenseropening,

Somecrushed icemag be dispensed eventhough gau selectedCUBEDICE.This happensoccasionallgwhen a few cubes accidentallgget directedto the crusher,

:::After crushediceisdispensed,somewater

mag drip from the chute

!.:Sometimesa smallmound af snow will

form onthe door inthe ice chute This condition is normal and usuallgoccurs

when gou have dispensedcrushed ice

repeatedlg Thesnow will eventuallg evaporate

GEAppliancesocom

Models without a shelf above the ice bin

To remove

Lift the bin then _ull i_

forward until the bin stops

Lift and pull forward again

to remove the bin

Removing and Replacing the Ice Storage Bin on Dispenser Models

Thereare two types of ice storage bins on dispenser models,One has ashelf above

the bin,the otherdoesnot Alwagssetthe icemakerpowerswitch to the

O(off) positionbeforeremovingthe icebin When replacing either typeof ice bin:

Alwagsbe sureto pressit firmlg intoplace If it does not go all the wag back removeit

and rotate the drivemechanism 1/4turn

Thenpush the bin backagain

Models with a shelf

above the ice bin

Toremove:

Pull _hebin straight ouL then lift past the stop position

,__i: _ ,,,, i _

: : i- -<::Zi: _,

Careand cleaning of the refrigerator.

Cleaning the Outside Thedispenser drip area ion some models),

beneaththegrille,shouldbewipeddrg Water left in thisarea mag leave deposits Remove

thedeposits bg adding undilutedvinegarto

Dispenserdriparea

thewell Soakuntil thedepositsdisappear or become looseenough to rinseowog

Thedispenser cradle(on somemodels) Beforecleaning,lockthe dispenserbg

pressingand holding theLock Controlspad for 3seconds Cleanwith worm waterand

bakingsoda solution- about a tablespoon (15ml}of bakingsoda toa quart (t liter) of water`Rinsethoroughkj and wipe drg

Cleaning the Inside

Tohelpprevent odors, leavean openbox ofbakingsoda in the freshfoodand freezer compartments

Unplug the refrigerator before cleaning,, If this isnotpractical,wring excessmoisture out of spongeorcloth when cleaning around switches,lights or controls

Usewarm water and baking soda solution- about a tablespoon(15mi)of baking soda to a quart (1liter)of water.Thisboth cleansand neutralizesodors Rinseandwipe drg

Thedoor handlesand trim, Cleanwith a cloth dampenedwith soapgwater,

Drgwith a softcloth

Keeptheoutside clean_Wipewith a cleancloth lightly dampened with kitchen appliancewax or mild liquiddish detergent

Drgand polishwith a clean,soft cloth

Do not wipe the refrigerator witi_ a sailed dish cloth or wet towel Thesema_/leave a residue that con erode the point Do not use scouring pads, powdered cleaners, bleach or cleaners containing bleach

because these products can scratch and weaken the paint finish

Useof ang cleaning solution other than that which is recommended,especially

thosethat contain petroleum distillates, can crack or damage the interior of the refrigerator..

Avoid cleaning cold glass shelves with hot

water because thee_treme temperature

difference may cause them to break Handle glass shelves carefully Bumping

tempered glass can cause it to shutter

Donot wash one plastic refrigerator

parts in the dishwasher

. J --

0 0

¢b

I/)

:i:• •••':::3"

!:I_LI:¸: ; ii Ji•

i_:;: _,/_: ,::

Care and cleaning of the refrigerator. CcontJ

Behind the Refrigerator

Becareful when movingthe refrigerator awag from the wall Afltgpes of floor'

coveringscan be damaged,particuladg cushionedcoveringsand thosewith embossedsurfaces

Puilthe refrigerator straight out and return itto position bg pushingit straight in Movingthe refrigeratorin a sidedirection

mag resultin damage to the floor covering or refrigerator.

Preparing for Vacation

For long vacations or absences, remove food and unplug the refrigerator. Clean the

interior with a baking soda solution of one tablespoon (15 ml)of baking soda to one quart (1liter) of water: Leave the doors open

Set the icemaker power switch to the O (off) position and shut offthe water

supplg to the refrigerator:

When pushing the refrigerator back. make sure gou don't roll over the power cord or icemaker supplg line (on some modelsL

If the temperature can drop below freezing. have o qualified servicer drain the water supply system (on some models} to prevent serious property damage due to flooding

4::

it.

Preparing to love

Secure all loose items such as shelves end drawers bg toping them securely in place

to prevent damage

When usinga hand truck to move the

refrigerator,donot restthe front or back ofthe refrigerator againstthe hand truck,

Thiscoulddamage therefrigerator:Handle onty from thesidesof therefrigerator,

Be sure the refrigerator stags in an upright position during moving

0 0

Ill

Replacing the light bulbs.

iiiiiiiiiiiiiiiii ii ...................... ii I1..111 i .111 i.i1 ii I I I I

GEAppliances,,com

NOTE: Turning the refrigerator off via the controls on the touch panel does not shut off electrical power to the refrigerator

Yourlight shield will look like one o! the following:

Refrigerator Compartment--Upper Light

0 Unplug the refrigerator, 0 0 Thebulbsare locatedat the top of

the compartment, insidethe light shield Onsome models,a screw at the front of

the lightshieldwiIihave to be removed Onother models,the screw is located in the pocket locatedat the backof

the shieid

0 Toremovethe lightshield,on some

models,pressin onthetabs on the sides ofthe shield and slideforward and out

Onothermodels,justslidethe shield forward and out

Refrigerator Compartment--Lower Light Thislight islocated above the top drawer

Unplugthe refrigerator. Lift the light shieldup and pull it out

0 After replacing the bulb with an appliance

O Plug the refrigerator back in

After replacingthe bulb with an appliance

bulbof thesame orlowerwattage. replacethe light shieldand screw When replacingthe light shield,make surethat

the tabs at the back of the shieldfit into the slotsat the backof the light shield

housing

Plugtherefrigerator back in

butbof the sameor lower wattage. replacethe shield

:_L :L i _ :

• V,,xz _

: / 7<, _

w A

tl f illgh!

Freezer Compartment O Unplugthe refrigerator. O

Removetheshelfjust above the light

shield (TheshetfwilIbe easier to remove

ifit isemptiedfirst )Removethe screwat

the topof the light shield Toremovethe light shield,pressinon the

sides,andlift upand out

Dispenser

Unplugthe refrigerator

0 Replacethe bulb with a bulb

Thebulb islocatedon the dispenser underthe control panel Removethe light

O Plug the refrigerator back in

bulb bg turningit counterclockwise

Refrigerator Compartment ton some modetsl

Thereis an LEDlightingdisplay in the top of the refrigeratorcompartment on some

models tfthis assembIgneedsto be

replaced,cattGEServiceat 1,8004322737 in the UnitedStatesor 1800 5613344

in Canada

Replace the bulb with an appliance bulb of the same or lower wattage,

and reinstall the light shield When reinstalling the light shield, make sure

the top tabs snap securely into place Replacethe screw

Reinstallthe shelf and plug the

refrigerator back in

of the same sizeand wattage

;:::x"

0 o

Installation

Refri erator

Instructions

Questions? Call 800.GE,CARES1800,432.2737} or Visit our Website at: GEAppliances.com

In Canada, call 1300.5613344 or Visit our Website at: www.GEAppliances_ca

BEFORE YOU BEGIN

Read these instructions completelg

and carefully,

• IMPORTANT - Save these instructions

for local inspector's use.

• IMPORTANT - Observe all governing

codes and ordinances

• Note to Installer - Be sure to leave these instructions with the Consumer_

- Note to Consumer - Keep these instructions

for future reference

• Skill level - installation of this appliance requires basic mechanical skiJls

• Completion time - Refrigerator Installation

30 minutes Water Line Installation

30 minutes

Proper installation is the responsibilitg of the installer

Product failure due to improper installation is not

covered under the Warrantg

If the refrigerator has alreadg been installed, remove the base grille (see Step 2 in Moving

the Refrigerator), then skip to Step 5 in Installing the Refrigerator.

Models

PREPARATION

WATER SUPPLY TO THE ICEMAKER

If the refrigerator has an icemoker; it will have to be connected to o cold water line. AGE water

supplg kit (containing tubing, shutoff valve, fittings and instructions} is available at extra

cost from LJOUrdealer, bg visiting our Website at GEAppliances,com (in Canada at

wwwoGEAppliances.ca} or from Ports and Accessories, 800 626 2002 (in Canada

:[888.261 30551

TOOLS YOU WILL NEED

22, 23, 25, 26, 27 end 29

,,,,,,,,,i, i1,,,,, ,, ,i i

3/8" and 5/16" Socket

Plastic Putty Knife

i,,/11,iul,/,/,/,/,/,/ui/ulJl,,i

1/2" and7/t6" Wrench

Phillips-HeadScrewdriver

Installation Instructions

MOVING THE REFRIGERATOR

[_ LOADING THE RERIGERATOR

ONTO A HAND TRUCK

Leave all tape and door pads on doors until

the refrigerator is in its final location To move the refrigerator, use a padded hand

truck Center the refrigerator on the hand truck and secure the strap around the refrigerator

DO NOT OVERTIGHTEN THE STRAR

If the refrigerator must go through ang entrance that is Jessthan 38" wide,

the doors must be removed Proceed to

Step 3 DO NOT remove the handles°

if all entrances are more than 38" wide,

skip to Installing the Refrigerator.

lU,I,,,I U U

[_] DISCONNECT THE WATER COUPLING

(on some models}

If the refrigerator has a water dispenser,

there is a water line from the cabinet into the bottom hinge on the freezer door that

must be disconnected.

To disconnect, push in on the white collar of the coupling and pull out the tubing

White collar

[] REMOVE THE BASE GRILLE

Remove the grille bg removing the two Phillips head screws

Bottom freezer

hinge

1.7

Installation Instructions

MOVING THE REFRIGERATOR(CONT.)

[] DISCONNECT THE POWER COUPLING

(on some models)

If the refrigerator has a water' dispenser,

there is a power line (harness) from the cabinet

into the bottom hinge on the freezer door that must be disconnected

To disconnect, pull apart at the coupling.

[] CLOSE THE FREEZER AND

m,,um,,,,,,uuluIH,,IHli,,li,i,ll ml II II luLm

H,,,,H,,lUUll IIm IIIIIIII IIIJ IIIII I

REFRIGERATOR DOORS

[_ DISCONNECT THE ELECTRICAL

CONNECTORS (on some models)

tf the refrigerator' has a refreshment center,

there are electrical connectors (harnesses) from the cabinet into the bottom hinge on the

refrigerator door that must be disconnected To disconnect, pull apart each connector:

Bottom refrigerator

hinge

[]_] REMOVE THE FREEZER DOOR

[_] Remove the freezer door top hinge cover bg

either squeezing it and pulling it up or bg prging it off with a plastic puttg knife

[] Remove the two 5/16" hex head screws, then

lift the hinge straight up to free the hinge pin,

5/t6" HexHead

[] Open the freezer door to 90 °

90°

Installation Instructions

IT) REMOVE THE FREEZER DOOR (cont.)

i_ As one person slowlg lifts the freezer door up

and off the bottom hinge, the second person should carefullg guide the water line and power

line (harness) through the bottom hinge

[] Set the door on a non-scratching surface with

the inside up.

[] REMOVE THE REFRIGERATOR DOOR

[] Remove the refrigeretor door top hinge cover

bg either squeezing it and pulling it up or bg prging it off with a plastic puttg knife

I_ REMOVE THE REFRIGERATOR DOOR

(canto)

t-_ Remove the two 5/16" he× head screws, then

lift the hinge straight up to free the hinge pin

5/16"HexHead

[_ Open the refrigerator door to 90°

98°

1,9

Installation Instructions

MOVING THE REFRIGERATOR(CONT.)

REMOVE THE REFRIGERATOR DOOR

(cont.)

Lift the refrigerator door up and off the bottom hinge

If the refrigerator has a refreshment center,

one person should slowlg lift the door up and off the bottom hinge and the second person should carefullg guide the electrical lines

(harnesses) through the bottom hinge

[_Z]REPLACING THE DOORS

.. ,, ,,,, , , , ,

To replace the doors, simplg reverse steps 3 through 8

However, please note the following:

• When lowering the doors onto the bottom hinges, make sure the second person

carefully guides the tube end harnesses through the holes in the hinges

• When connecting the water line, make sure you insert the tubing oil the wag to the mark,

Re{reshment Center Models only

[]

Set the door on a non-scratching surface with the inside up.

i,iu,llllunu

Mark

- Do not pinch the tubing and harnesses when placing the doors on the bottom hinges

° When connecting the power line and the

electrical lines (refreshment center models only), be sure that the connectors ore seated together fully

Installation instructions

INSTALLING THE REFRIGERATOR

REFRIG ERATOR LOCATION

• Do not install the refrigerator where the temperature will go below 60°F (16°C) because

it wil! not run often enough to maintain proper temperatures

o Do not install the refrigerator where the

temperature will go above 100°F (37°C) because it will not perform properlg

° Install it on o floor strong enough to support

it futtg loaded

CLEARANCES

Allow the following clearances for ease of installation, proper air circulation end plumbing

and electrical connections: Sides 1/8" (4 mm) Top 1" (25 mm)

Back 1" (25 ram)

Installation Instructions

INSTALLING THE REFRIGERATOR (CONT.}

ril

CONNECTING THE REFRIGERATOR

TO THE HOUSE WATER LINE

(icemaker and dispenser models}

A cold water suppiy is required for automatic icemaker and dispenser operation, If there is not a cold water supplg, gou wiil need to

provide one, See "Installing the Water Line" section

NOTES:

• Before making the connection to the refrigerator, be sure the refrigerator power

cord is not plugged into the wall outlet

- If your refrigerator does not have a water filter, we recommend installing one if gour

water supply has sand or particles that could clog the screen of the refrigerator's water

valve install it in the water line near the refrigerator If using GESmartConnect"

Refrigerator Tubing Kit, you will need an additional tube (wx08×100021 to connect

the filter, Do not cut plastic tube to instot! filter

[]

If gou are using copper' tubing, place a

compression nut and ferrule (sleeve) onto the end of the tubing coming from the house cold

water supply If gou ore using the GE SmartConnect'"

tubing, the nuts ore alreadg assembled to the tubing

[]

If gou ore using copper tubing, insert the end of the tubing into the refrigerator

connection at the back of the refrigerator, as far as possible While holding the tubing,

tighten the fitting,

If gou ore using GE SmortConnect'" tubing, insert the molded end of the tubing into the refrigerator connection, at the back of the

refrigerator, and tighten the compression nut until it is hand tight, Then tighten one additional turn with a wrench Overtightening

mag cause leaks

[][] CONNECTING'THEREFRIGERATOR{cont.}

[C1 Fasten the tubing into the clamp provided to

hold it in position You meg need to pry open the clamp

CompressionNut

Ferrule (sleeve)

Refrigerator Connection SrnartConnecffTubing

[] TURN ON THE WATER SUPPLY

Turn the water on at the shutoff valve (house water supply) end check for any leaks

I_ PLUG IN THE REFRIGERATOR

Before plugging in the refrigerator, make sure

the icemaker power switch is set to the 0 (off} position.

I/4" Tubin

See the grounding information attached to the power cord

Installation Instructions

J_ PUT THE REFRIGERATOR IN PLACE

Hove the refrigerator to its final location

[] LEVEL THE REFRIGERATOR

The refrigerator can be leveled bg adjusting

the rollers located near the bottom hinges

"_. Rollers

Raise

Rollers have three purposes: . Rollers adjust so the door closes easilg when

opened about halfwag (Raise the front about

5/8" [16 mm] from the floor,)

° Rollers adjust so the refrigerator is firmly

positioned on the floor and does not wobble

• Rollers allow you to move the refrigerator away from the wall for cleaning

To adjust the rollers:

° Turn the roller

adjusting screws clockwise to raise

the refrigerator, counterclockwise

to lower it Use a 3/8" hex socket or

wrench, or an adjustable wrench

j_ LEVEL THE DOORS

Adjust the refrigerator door to make the doors even at the top

To align:

Using a 7/16" wrench, turn the door adjusting screw to the right to raise the door, to the left

to lower it NOTE:

A nylon plug, imbedded in the threads

of the pin, prevents the pin from turning unless a wrench is used

After one or two turns of the wrench, open

and close the refrigerator door and check

the alignment at the top of the doors

,_ Doors should beeven at top

Roller adjusting screw

Installation instructions

INSTALLING THE REFRIGERATOR(CONT.)

,ill J Jl

I_ REPLACE THE BASE GRILLE

Replace the grille bg installing the two Phillips head screws

[] START THE ICEMAKER

Set the icemoker power switch to the i Ion] position The icemaker will not begin to operate until it reaches its operating temperature of

15°F (-9°C) or below It will then begin operation

outometicollg It will take 2-3 dags to fill the ice bin

NOTE: In lower water pressure conditions, the water

valve mag turn on up to 3 times to deliver enough water to the icemaker

,,i iJll Jlill i i i

,w,,c,-_ll_

i I

JllJllJllJllJlllJllllllJII I II Ill

[] SET THE CONTROLS

set the controls to the recommended setting

0 _F IS RECOM_(tSNDED 37 *F _S RECOMMEND ED

Installation Instructions

INSTALLING THE WATER LINE {ICEMAKER &DISPENSERMODELS)

BEFORE YOU BEGIN

Recommended copper water supplg kits are WX8X2,

WX8X3 or WX8X4, depending on the amount of tubing you need Approved plastic water supplg lines are GE

SmartConnect '_ Refrigerator Tubing (WXO8XIO002, WXO8XIO006, WXO8XtO015 and WXO8X10025)

When connecting your refrigerator to a GEReverse Osmosis Water Sgstem, the only approved installation

iswith a GERVKit For other reverse osmosis water systems, folIow the manufacturer's recommendations

if the water supplg to the refrigerator is from a Reverse Osmosis Water Filtration System AND

the refrigerator also has a water filte_ use the refrigerator's filter bypass plug Using the refrigerator's water filtration cartridge in

conjunction with the ROfilter con result in hollow

ice cubes and slower water flow from the water

dispenser This water line installation is not warranted bg

the refrigerator or icemaker manufacturer Follow these instructions carefulIg to minimize the risk

of expensive water damage, Water hammer {water bonging in the pipes)in

house plumbing con cause damage to refrigerator ports and lead to water leakage or flooding Call a

qualified plumber to correct water hammer before installing the water supplg line to the refrigerator,

To prevent burns and product damage, do not hook

up the water line to the hot water line If you use your refrigerator before connecting the

water line, make sure the icemaker power switch is

in the O (off) position Do not install the icemaker tubing in areas where

temperatures fa!l below freezing When using any electrical device (such as o power

drill} during installation, be sure the device is double insulated or grounded in a manner to prevent the

hazard of electric shock, or is batterg powered

All installations must be in accordance with local

plumbing code requirements

WHAT YOU WILL NEED

o Copper or GE SmartConnect'" Refrigerator

Tubing kit, 1/4" outer diameter to connect the refrigerator to the water supplg If using copper, be sure both ends of the tubing are cut square,

To determine how much tubing gou need: measure the distance from the water valve on the back of

the refrigerator to the water supptg pipe Be sure there is sufficient extra tubing to allow the

refrigerator to move out from the wall after installation

GE SmartConnect'" Refrigerator Tubing Kits are available in the following lengths: 2' (0,6 m) - W×08×10002

6' (18 m) - WXO8XIO006

15'(46 mt - WXO8X10015

25'(76 m} -WX08X10025

Installation instructions

INSTALLING THE WATER LINE (CONT.)

Install the shutoff valve on the nearest frequentlg

WHAT YOU WILL NEED (CONT.)

NOTE: The onlg GE approved plastic tubing is that supplied in GE SmartConnect"

Refrigerator Tubing kits. Do not use ang other

plastic water supplg line because the line is under pressure at all times. Certain tapes of plastic wilt crack or rupture with age and cause

water' damage to gour home. , A GE water supplg kit (containing tubing,

shutoff vatve and fittings listed below) is available at extra cost from gout dealer or from Parts and Accessories, 800 626 2002 (in Canada

1888261 3055[

° A cold water supptg. The water pressure must be

between 20 and 120 p s L(t 4-8 t bar)

• Power drill.

• 112" or adjustable wrench.

• Straight and Phillips blade screwdriver.

used drinking water line

[_] HUT OFF THE MAIN WATER SUPPLY

Turn on the nearest faucet long enough to clear the line of water'

. ..,.,11,, u Ji i i

CHOOSE THE VAWE LOCATION

Choose a location for the valve that is easilg accessible It is best to connect into the side of

a vertical water pipe.. When it is necessarg to connect into a horizontal water pipe, make

the connection to the top or side, rather' than at the bottom, to avoid drawing off ang

sediment from the water pipe

• Two 114" outer diameter compression nuts and 2 ferrules (sleeves)-to connect the copper

tubing to the shutoff valve and the refrigerator water valve

• If gou are using a GE SmartConnect" Refrigerator Tubing kit, the necessary fittings are preassembted to the tubing

• If gour existing copper water line has a flared

fitting at the end, you will need on adopter

(available at plumbing supplg stores) to connect the water line to the refrigerator OR you con cut

off the flared fitting with o tube cutter and then use o compression fitting Do not cut formed end

from GE SmartConnect'" Refrigerator tubing

• Shutoff valve to connect to the cold water line. The shutoff valve should have a water inlet with o

minimum inside diameter of 5/32" at the point of connection to the COLD WATERLINE Saddte-tgpe shutoff valves are included in many water supplg

kits Before purchasing, make sure o saddle-tape valve complies with your local plumbing codes

[] DRILL THE HOLE FOR THE VALVE

Drill o 1/4" hole in the water pipe (even if using

a self-piercing valve), using a sharp bit. Remove ang burrs resulting from drilling the hole in

the pipe Take care not to allow water to drain into

the drill.

Failure to drill a 1/4" hole meg result in reduced ice production or smaller cubes

Installation Instructions

[] FASTEN THE SHUTOFF VALVE

Fasten the shutoff valve to the cold water pipe

with the pipe clamp

Saddle-Type Vertical CoidWater Pipe Shutoff Valve

NOTE:Commonwealth of Massachusetts

Plumbing Codes 248CHR shall be adhered to Saddle valves are illegal and use is not permitted

in Hassachusetts Consult with your licensed plumber

[] TIGHTEN THE PIPE CLAMP

Tighten the clamp screws until the sealing washer begins to swell

NOTE: Do not overtighten or you meg crush the tubing

Washer

Pipe

Clamp

inlet End

I_ CONNECT THE TUBING TO THE VALVE

Place the compression nut and ferrule (sleeve) for copper tubing onto the end of the tubing and

connect it to the shutoff valve Hake sure the tubing is fully inserted into

the valve. Tighten the compression nut securely.

For plastic tubing from a GE SmartConnect"

Refrigerator Tubing kit, insert the molded end of the tubing into the shutoff valve and tighten compression nut until it is hand tight, then

tighten one additional turn with a wrench. Overtightening may cause leaks.

Saddle-Type

Shutoff Valve_.

PackingNut

0u[let Valve Ferrule (sleeve)

NOTE: Commonwealth of Hassachusetts Plumbing Codes 248CHR shall be adhered to

Saddle valves ore illegal and use is not permitted in Massachusetts Consult with your licensed plumber.

FLUSH OUT THE TUBING

Compression Nut

,Ill, H,,,,,,,, HIIIIII I I ,,,,

[] ROUTE THE TUBING

Route the tubing between the cold water line

and the refrigerator

Route the tubing through a hole drilled in the

wall or floor (behind the refrigerator or adjacent

base cabinet) as close to the wall as possible

NOTE: Be sure there is sufficient extra tubing to allow the refrigerator to move out from the wall

after installation.

Turn the main water supply on and flush out the tubing until the water is clear

Shut the water off at the water valve after about one quart (t liter) of water has been flushed through the tubing

.,u iiiiii uul

To complete the installation of the refrigerator, go back to Step I in Installing the Refrigerator.

Normal operating sounds.

Newer refrigerators sound different from older refrigerators Modem refrigerators have more features

end use newer technology,

Do you hear what I hear? These sounds are normal.

l.I

Ill

-- ° .

_,ti El'h

: _L _ !:_

: _/ •: X¸

k :_ ', _ L

_::/!i/!i ! V,

HUMMM...

_WHOOSH...

[] The new high efficiencg compressor mag run foster

and longer than gour old refrigerator and gou mag heor a high-pitched hum or pulsating sound while it is operating

111Sometimesthe refrigerator runs for an extended period

especiallgwhen the doorsare openedfrequentlg This means that theFrost Guard'_feature isworking to prevent

freezerburn and improve food preservation

[] Youmag hear a whooshing soundwhen the doors close

Thisisdue to pressureequalizingwithin the refrigerator:

CLICKS,POPS,

CRACKSand CHIRPS

I Youmug hear cracking or popping sounds when the

refrigerator is first plugged in, This happens as the refrigerator cools to the correct temperature

[]

Electronic dampers click open and closed to provide

optimal cooling and energg savings.

[]

The compressor mog cause a clicking or chirping sound when attempting to restart (this could take up to 5 minutes)

[] The electronic control board mag cause a clicking

sound when relags activate to control refrigerator components

lU Expansion and contraction of cooling coils during and

after defrost can cause a cracking or popping sound.

i On models with an icemaker: after an icemaking cgde,

gou mag hear the ice cubes dropping into the ice bucket

WHIRl

Im You mag hear the fans spinning at high speeds,

This happens when the refligerator is first plugged in, when the doors are opened frequentlg or when a large

amount of food is added to the refligerator or freezer compartments The fans are helping to maintain the correct temperatures

[] If either door is open for over 3 minutes, gou mag hear

the fans come on in order to cool the light bulbs

[] The fans change speeds in order to provide optimal

cooling and energg savings

WATER SOUNDS

lU The flow of refrigerant through the freezer-cooling coils

mag make a gurgling noise like boiling water_

[] Water dropping on the defrost heater can cause a

sizzling, popping or buzzing sound during the defrost cgcle

[] A water dripping noise mag occur during the defrost

cgcle as ice melts from the evaporator and flows into the drain pan

II1 Closing the door mag cause a gurgling sound due to

pressure equalization

tt.

Before gou call for service...

GEAppliances,com

Troubleshooting Tips

Savetime and money! Reviewthe charts on the following pages first end gou meg not need to cal!for service

Possible Causes What To Do

Refrigerator does not Refrigerator in defrost cycle. •Wait about i0 minutes for defrost cgcle to end operate Eitheror both controls set to OFF° o Set the controls to a lower temperature setting

Refrigerator is unplugged, o Push the plug completelg into the outlet

The fuse is blown/circuit • Replace fuse or reset the breake[ breaker is tripped°

Refrigerator is in showroom mode, ° Unplug the refrigerator and plug it back in.

Vibration or rattling Rollers need adjusting, • See Rollers

(slight vibration is normal)

Motor operates for Normal when refrigerator o Wait 24 hours for the refrigerator to completeig long periods or cgcles is first plugged in. cool down

on and off frequentlg. (Modem refrigerators Often occurs when large • This is normat.

with more storage amounts of food ore space and a larger placed in refrigerator,.

freezer require more Door left open, - Check to see if package is holding door open

operating time, Theg

start and stop often Hot weather or frequent ° This is normal to maintain even door opening&

temperatures,) Temperature controls • SeeAbout the controls

Refrigerator or freezer Temperature control not set o See About the controls compartment too worm cold enough.

Frost or ice crgstals Door left open. o Check to see if package is holding door open on frozen food

(frostwithin package Too frequent or too long is normal) door openings_

Divider between Automatic energg saver ° This heips prevent condensation on the outside refrigerator and freezer sgstem circulates warm

compartments liquid around front edge feels warm of freezer compartment.,

set at the coldest setting,,

Warm weather or frequent • Set the temperature control one step coIder. door openings.. See About the controls

Door left open. • Check to see if package is holding door open

¢3

vn f _,,,k r'IP

. ° __

v A

:: :: :

i:_!:!_z_i_!?,:i:i(I

,/!:i_:!L!:i :_:!:_:

Automatic icemaker Icemaker power switch , Set the power switch to the I (on; position

does not work is in the O (of_ position,

Water supplg turned offer • See Installing the water line not connected,,

Freezer compartment • Wait 24 hours for the refrigerator to completelg too warm° cool down

Piled up cubes in the storage , Level cubes bg hand bin cause the icemaker

to shut off_ Ice cubes stuck in icemaker.,

(Green power light on icemaker blinking).,

° Turnoffthe icemoker,removecubes,and turn the

icemakerbackon

O _J

w-. 1-11 n

v A

Before you call for service,,,......

Troubleshooting Tips

Possible Causes What To Do

ice cubes have Ice storage bin needs cleaning.. • Emptg and wash bin Discard old cubes

odor/taste

Small or hollow cubes Water filter clogged° • Replace filter cartridge with new cartridge or with plug Slow ice cube freezing Door left open.. • Check to see if package is holding door open.

Orange glow in Defrost heater is on.. • This is normal the freezer

Cube dispenser does not lcemaker turned off or • Turn on icemoker or water supplg work (on some models) water supplg turned off.

Food transmitting odor/taste , Wrap foods well

to ice cubes.

Interior' of refrigerator • SeeCare andcleaning

needs cleaning.

Temperature control not set • See About the controls cold enough.

Ice cubes ore frozen to • Remove cubes. icemaker feeler arm.

An item is blocking or has fallen ° Remove ang item that might be blocking, or has fallen

into the ice chute inside the top into. the chute

door' bin of the freezer'.

_i.i!_:i:i::IL_1

iiiii !

i!blii(;:):i(i:

(J1

Irregular'iceclumpsin

storage container,

° Breakupwith fingertippressureand discard

remainingclumps

• Freezermagbe too warm Adjustthe freezercontrol to a coldersetting, oneposition at a time,untit clumps

do not form

Dispenser is LOCKED. • Press and hold the Lock Controls pad for 3 seconds

Water has poor taste/ Water' dispenser has not been • Dispense water until all water in sgstem is replenished odor (onsome models] used for a long time_

Water in first glass is Normal when refrigerator • Wait 24 hours for the refrigerator to completelg warm !on same models) isfirst installed., cool down

Water dispenser has not been • Dispense water until eli water in sgstem isreplenished used for a long time.

Water sgstem has been drained° • Allow several hours for-replenished supplLJto chill

Water dispenser does Water supplg line turned ° See Installing the water line

not work fan some off or not connected..

models)

Water spurting from Newlg-installed filter cartridge_ • Run water from the dispenser for 3 minutes (about dispenser tonsome models) one and a half gallons}

Water is not dispensed Water in reservoir" is ° Call for service (on some models} but frozen,.

icemaker is working

30 is too cold,

Water' filter clogged,, • Replace filter cartridge or remove filter and install plug, Air mag be trapped in the • Pressthe dispenser arm for at least two minutes

water' sgstem.

Dispenser is LOCKED. • Pressand hold the Lock Controls pod for3 seconds.

Refrigerator control setting , Set to a warmer setting,

+ 82 hidden pages