GE GSHS5MGXBESS, GSHS5KGXBCSS, GSHS3KGXBCSS, GSHL5MGXBELS, GSHL5KGXBCLS Owner’s Manual

0

€11

0

Olllll

€11

ge.com

Safety Instructions ........... 2-4

Operating Instructions

Automatic Icemaker ............... 12

Care and Cleaning ............. 14, 15

ClimateKeeper2". ................... 6

Crispers and Pans ................. 11

CustomCooP . ...................... 6

Ice and Water Dispenser ........... 13

Refrigerator Doors ................. 10

Replacing the Light Bulbs .......... 16

Shelves and Bins .................. 8, 9

Temperature Controls ............... 5

TurboCool T" ......................... S

Water Filter ......................... 7

Models 23, 25, 26, 27 ond 29

Profile C6te 5 C6te

R frig rateurs

La section frangaise commence 6 la page 46

Installation Instructions

Installing the Refrigerator ....... 26-29

Moving the Refrigerator ........ 22-25

Preparing to Install

the Refrigerator .................... 21

Trim Kits and Panels ............ 17-20

Water Line Installation ......... 50-32

Troubleshooting Tips ...... 33-36

Normal Operating Sounds .......... 33

Consumer Support

Consumer Support ........ Back Cover

Performance Data Sheet ........... 41

Product Registration ............ 45, 44

State of California Water

Treatment Device Certificate ....... 42

Warrantg (Canadian) ............... 39

Warrantg (U.S.) .................... 40

ProfileLadoa Lado

Refrigeradores

La secci6n en espafial empieza en la p6gina 88

Write the model and serial numbers
here:

Model #

Serial #

Find these numbers on a label inside
the refrigerator compartment at the top

on the right side.

200D8074P020 49-60543-1 02-08 JR

IMPORTANT SAFETY INFORMATION.
READ ALL INSTRUCTIONS BEFORE USING.

WARNING!

Use this appliance only for its intended purpose as described in this Owner's Manual.

SAFETYPRECAUTIONS

When using electrical appliances, basic safetg precautions should be followed, including the following:

_',_Thisrefrigerator must be properlg installed

and located in accordance with the Installation
Instructions before it is used.

Do not allow children to climb,stand or hang
on the shelvesinthe refrigeratonThegcould

damage the refrigerator and seriouslg injure
themselves.

::_:_Do not touch the cold surfaces in the freezer

compartment when hands are damp or wet.
Skinmag stick to these extremelg cold surfaces.

_,',_Do not store or usegasoline or other flammable

vapors and liquidsin the vicinitg of this or ang
other appliance.

In refrigerators with automatic icemakers,
avoid contact with the moving parts of the ejector

mechanism, or with the heating element located
on the bottom ofthe icemakenDonot placefingers

or hands on the automatic icemaking mechanism
while the refrigerator is plugged in.

_,',_Keepfingers out of the "pinch point" areas;

clearances between the doors and between
the doors and cabinet are necessarilgsmall.

Be careful closing doors when children are
in the area.

:¢;Unplug the refrigerator before cleaning and making

repairs.

NOTE:Westrongly recommendthat anblservicing
be performed bblaqualified individual.

:¢;Setting either or both controls to OFFdoes not

remove power to the light circuit.

::_:_Do not refreezefrozen foods which have thawed

completelg.

II, DANGER! RISK OF CHILD ENTRAPMENT

PROPERDISPOSAL OF THE REFRIGERATOR

ge.com

'C:IIIZ¸

ii//i/i!ii)i))iiii/

Childentrapment and suffocation are not problems
of the past. Junked or abandoned refrigerators are

still dangerous_.evenif they will sit for '_justafew
days." Ifyou are getting rid of your old refrigerator,

pleasefollow the instructions below to help prevent
accidents.

Refrigerants

All refrigeration products contain refrigerants,
which under federal law must be removed prior

to product disposal. If you are getting rid of an
old refrigeration product, check with the company

handling the disposal about what to do.

Before You ThrowAway Your Old
Refrigerator or Freezer:

iTake off the doors.

i;ffLeavethe shelves in place so that children may not

easily climb inside.

USEOFEXTENSIONCORDS

Because of potential safety hazards under certain conditions, we strongly recommend against the use
of an extension cord.

However,if you must use an extension cord,it isabsolutely necessary that it bea UL-listed(inthe UnitedStates)
or a CSA-listed(inCanada),3-wire grounding type appliance extension cord having a grounding type plug and

outlet and that the electrical rating of the cord be 15 amperes (minimum) and 120volts.

t_

q-

0

_° f,m

g
2=

€,n

¢b

o

IHPORTANT SAFETY INFORHATION.
READ ALL INSTRUCTIONS BEFORE USING.

WARNING!

HOW TO CONNECT ELECTRICITY

Do not, under ang circumstances, cut or remove the third (ground) prong from the power cord.
For personal safetg, this appliance must be properlg grounded.

The power cord of this appliance is equipped

with a 3-prong (grounding)plug which mates
with a standard 3-prong (grounding)wall outlet

to minimizethe possibility of electric shock hazard
from this appliance.

Have the wall outlet and circuit checkedby
a qualified electrician to make sure the outlet is

properly grounded.
If the outlet isa standard 2-prong outlet, it isyour

personal responsibility and obligation to have it
replaced with a properly grounded 3-prong wall

outlet.

The refrigerator should always be plugged into its

own individual electricaloutlet which has a voltage
rating that matches the rating plate.

Thisprovides the best performance and also prevents
overloading house wiring circuits which could cause

a fire hazard from overheatedwires.
Never unplug your refrigerator by pulling on the

power cord.Alwags grip plug firmly and pull straight
out from the outlet.

Repairor replaceimmediately all power cords that
have become fraged or otherwise damaged. Do not

usea cord that shows cracks or abrasion damage
along its length or at either end.

When moving the refrigerator away from the wall,
be careful not to roll overor damage the power cord.

READAND FOLLOWTHISSAFETYINFORMATIONCAREFULLY.

SAVETHESEINSTRUCTIONS

4

About the temperature controls, ge.com

Nat all features are an all models.

Hold 3 seconds Hold 3 seconds

to Reset

Thetemperaturecontrolsorepresetinthefoctor_tat37°FfortherefrigeratorcompartmentandO°Fforthe
freezercomportment.Allow24hoursforthetemperatureto stabilizetothepresetrecommendedsettings.

ThetemperaturecontrolscondisplogboththeSETtemperatureaswellastheactualtemperaturein
therefrigeratorandfreezenTheactualtemperaturemay varyslightlyfromtheSETtemperaturebased
onusageandoperatingenvironment.

i_ Onsomemodels,settingbothcontrolstothewarmestsettinguntilthedisplogflashes(off)willstop

coolinginboththefreezerandrefrigeratorcompartments.

:_ Onothermodels,settingeithercontroltothewarmestsettingund thedisplayflashes(off)willstop

thecoolingto thefreezerandrefrigerator.

_,_NOTE;Turningtherefrigeratoroffviathecontrolsonthetouchpaneldoesnotshutoffelectricalpower

totherefrigerator.

NOTE:Therefrigeratorisshippedwithprotectivefilmcoveringthetemperaturecontrols.Ifthisfilmwas
notremovedduringinstallation,removeitno_z

e,,l,

t_

0

iiiiiiii_;iiiiiiil

i_iii_ii,:,::,iiiii

L{'

Performance Air Flow Sgstem

ThePerformanceAir-FlowSystemisdesignedto

maximizetemperaturecontrolintherefrigerator
andfreezercompartments.Thisuniquespecial
featureconsistsoftheAirToweralongthe back
wallof therefrigeratorandtheAirTunnelonthe

bottomportionofthefreezerrearwall.Placing
foodinfrontof thelouversonthesecomponents

About TurboCool ." Ionsome models)

Ill

ITURBOCOOL I

How it Works

TurboCoolrapidlycoolstherefrigerator

compartmentinorderto morequicklycoolfoods.
UseTurboCoolwhen addinga largeamount

offood totherefrigeratorcompartment,putting
awayfoodsaftertheyhavebeensittingout at

roomtemperatureorwhenputtingawaywarm
leftovers.Itcan alsobeusediftherefrigeratorhas

beenwithoutpowerfor anextendedperiod.
Onceactivated,the compressorwillturnon

immediatelyandthefanswill cycleonandoff
athighspeedasneededfor eighthours.

Thecompressorwill continuetorununtilthe

refrigeratorcompartmentcoolsto approximately
34°F(1°C),thenitwill cycleonandofftomaintain

thissetting.After8 hours,or ifTur6oCaolis

pressedagain,the refrigeratorcompartment

willreturnto theoriginalsetting.

willnot affectperformance.AlthoughtheAirTower
andtheAirTunnelcanbe removed,doingsowill
affecttemperatureperformance.(Forremoval
instructions,on-line,contactusatge.comor
call800.GE.CARES.InCanada,contactusat
geappliances.caorcall1.800.561.3344.)

Howto Use

PressTurboCool.TheTur6oCoolternperature
displaywillshowTcandthe LEDwillbeactivated.

AfterTur6oCoolis complete,the Tur6oCool
indicatorlightwillgoout.

NOTES;Therefrigeratortemperaturecannot

bechangedduringTur6oCaol.

Thefreezertemperatureisnot affected

duringTur6oCaol.

Whenopeningtherefrigeratordoor

duringTur6oCaol,thefanswillcontinue

to runifthey havecycledon.

8

('b
o

R

About ClimateKeeper2.TM

How it Works

The new ClimateKeeper2TM isthe industrg's

most advanced refrigeration system,

delivering optimum temperature and

humidity performance to keepfood
garden fresh longerand reduce freezer

burn,while maintaining Estar-level efficiency.

The new ClimoteKeeper2 system features
two evaporators--one for the refrigerator

and one for the freezeE

This providestwo separate cooling systems
for the entire unit, and separatesthe airflow

between the fresh food and freezer sections
during normal coolingoperations.

This ensuresthat the humidity levels inthe
fresh food section are significantly higher

than in a conventional system,* allowing
fresh produce and other unsealedfoods to

retain their moisture content and freshness
IongeEMoisture sensitivefoods such asfresh

About CustomCool/'(on somemodels)

How to Use

0 Empty the pan. Placethe Chill/Thaw tray

in the pan.Placethe items on the tray

and closethe pan completely.

LCDModels:

Accessb&/:Home > Options >

Refrigerator Options > CustomCool Pan

F_xpressThawTM

ExpressChill"

Non-LCD Models:

Selectthe ExpressThawTM, ExpressChill_"
or SelectTemp_"pad.The display and SET
light will come on. Tapthe pad until the

light appears next to the desired setting.
Usethe following chart to determine the

best setting to use.
_;: ExpressChillcan be setto 15,30 or45

minutes.Thedefault is15 minutes.

i_:);Tostop a feature before it isfinished:

For LCDModels:
Go into that feature's menu and press

the OFFbutton.

fruit, salads,rice,etc.,can now be stored on
open shelveswithout excessivemoisture loss.
Dueto the higher humidity in the refrigerator,

you may on occasion experience fog or small
amounts of moisture in the refrigerator

compartment. This isnormal and may
come and go as different food loads

and environmental conditions change.
Wipe dry with a paper towel if desired.

The separate airflow system minimizes

the mixing of air between the two
compartments, which reduces odor

transfer to improve the taste of ice.

The ClimateKeeper2 system also reduces

the number of defrosting cycles in the freezer
evaporator,thereby reducing freezer burn.

*Testingshows a higher levelof humidity in

the FreshFoodsection in ClimoteKeeper2
refrigeratorsversus conventionalunits.

For Non-LCD Models:

Tapthat feature's pad until nooptions
are selected and the display isoff.

;';;: During ExpressThaw and

ExpressChill,the display onthe
controlswill count down the time

inthe cycle (onsome models).

_: After the ExpressThaw cycle is

complete,the pan will resetto the
MEATsetting (32°F[0°C])to help

preservethawed items until they
are used.

i::)_ Thedisplayed actual temperature

ofthe CustomCool pan may vary
slightly from the SETtemperature

basedon usage and operating
environment.

NOTE:Forfood safety reasons,it is
recommended that foods bewrapped in

plastic wrap when usingExpressThaw.
Thiswill help contain meatjuices and improve

thawing performance.

How to Remove and Replace the Drawer

Toremove: _ Lockall four swing locks by rotating them

Pullthe drawer out to the stop position, to the lock position.

0 Rotate all four swing locks to the unlock

position.

Lift the front of the drawer up andout.

Toreplace:

Make sure allfour swing locksare in

the unlock position.

Placethe sidesof the drawer into

6

the drawer supports, making sure

the swing locks fit onthe drawer slots.

About the water filter. (onsome models)

ge.com

Water Filter Cartridge

Thewater filter cartridge islocated in the back upper right
comer of the refrigerator compartment.

When to Replace the Filter on Models With

a Replacement Indicator Light

Thereis a replacement indicator light for the water filter
cartridge on the dispenseEThislight will turn orange to tell

you that you need to replace the filter soon.
Thefilter cartridge should be replaced when the replacement

indicator light turns redorif the flow of water to the dispenser
or icemaker decreases.

When to Replace the Filter on Models Without

a Replacement Indicator Light

Thefilter cartridge should be replaced every sixmonths or
earlier if the flow of water to the water dispenser or icemaker

decreases.

Removing the Filter Cartridge

If you are replacingthe cartridge, first remove the old one
by slowly turning it to the left. Do not pull down on the

cartridge. A small amount of water may drip down.

Installing the Filter Cartridge

O If you are replacing a SmartWater cartridge with

an adapter, it must be removedbefore installing the
cartridge. Toremove the adapter,turn it to the left

about 1/4turn.

Lineup the arrow on the cartridge and the cartridge
holdeEPlacethe top of the new cartridge up inside

the holdeEDo not push it up into the holder

Slowly turn it to the right until the filter cartridge stops.

DONOTOVERTIGHTEN.Asyou turn the cartridge, it will

automatically raiseitself into position.The cartridge will

move about 1/2turn.

Hoder _//I

O Runwater from the dispenserfor Sminutes (about

1-1/2 gallons)to clear the system and prevent sputtering.

Pressand hold the WATERFILTERpad (onsome models)
on the dispenserfor 5 seconds.

NOTE:A newly-installed water filter cartridge mag cause
water to spurt from the dispenser

Filter Bypass Plug

You must usethe filter bypass plug when a replacement filter

cartridge is not available.The dispenser and the icemaker will
not operate without the filter or filter bypass plug.

-,,,,,,,

¢b

0

#iiiiiJiiii#

L_

If you are replacing a Water by Culligoncartridge,
leavethe adapter in place.Thisadapter will stay in

the refrigerator when you replacefuture cartridges.

With adapter Without adapter

(appearance may vary)

O On models without a replacement indicator light, apply

the month and gear sticker to the new cartridge to remind
you to replacethe filter in six months.

Fillthe replacement cartridge with water from the tap to
allow for better flow from the dispenser immediately after

installation.

,_.,. _ Bypass

r _er .----'_ Plu_ ,

Bgpass _ _

SmartWater Water by Cuttigan

Filter

Touse the filter bgpassplug on Water bg Culliganmodels,

you must first remove the filter adapter from the cartridge
holder bgturning it to the left.

If you have questions-visit our Website at ge.com,
or call 1.800.GECARES(1.800.432.2737).

Replacement filters:
Toorder addffional filter cartridges in the United States,

visff our Website at ge.com, or call GEParts and

Accessories, 800.626.2002.

MSWF
Suggested Retail $36.95-41.95

Customers in Canada should consult the yellow pages

for the nearest Habe Service Center

:b"

8

¢b

o

About the shelves and bins.

Not all features ore on oil models.

Refrigerator Door Bins and Freezer Door Tilt-Out Bins

Large Bins Thesnugger helps prevent tipping, spilling

The larger refrigerator door bins and freezer
tilt-out door bins are adjustable.

Toremove: Lift the front of the bin straight
up,then lift up and out.

Refrigerator bin

/

Toreplace or relocate: Engagethe back side

of the bin in the molded supports on the dooE
Then push down on the front of the bin. Bin

will lock in place.

Small Bins

Toremove: Lift the front of the bin straight up

then out.

or sliding of small items stored onthe door
shelf.Placea finger on either side ofthe

snugger near the rear and move it back
and forth to fit your needs.

Donotblock CAUTION:

Becareful when

placing items in

the top bin,Hake
surethat items do

not block or fall
into the icechute.

Freezer tilt-out bin

Presstab and pull shelf forward

to remove

Toreplace: Positionthe bin above the

rectangular molded supports on the door.

Then slidethe bin down onto the support
to lock it in place.

Slide-Out Spillproof Shelf

The slide-out spillproof shelf allows gou
to reach items stored behind others.

The specialedges are designedto help

prevent spillsfrom drippingto lower shelves.

Toremove:

Slidethe shelf out untilit reaches the stop,

then press down on the tab and slide
the shelf straight out.

Top freezer bin

CAUTION:

II

Do not block

Port must bein

place as shown

for proper ice
dispensing.Food

cannot be stored
in this location.

Top freezer bin (on some models)

Toreplace or relocate:

Linethe shelf up with the supports and slide
it into place.The shelf can be repositioned

when the door is at 90° or more. To reposition
the shelf,slide the shelf past the stops and

angle downward. Slideshelf down to the
desiredposition, lineup with the supports

and slide into place.
Hake sure you push the shelves oll the wag

back in before _jou close the door.

QuickSpace TM Shelf

This shelf splitsin half and slidesunder itself
for storage of tall items on the shelf below.

This shelf can be removed and replaced

or relocatedjust likethe Slide-OutSpillproof
Shelves.

8

Onsome models, this shelfcannot be used
in the lowest position.

Not all features are on oil models.

Freezer Baskets

ge.com

Toremove, push the basket all the wag to
the back of the freezeELift up until the back

pinsare disengaged. Liftthe entire basket

up and pull out.

Slide-Out Freezer Shelves

Toremove, slide out to the stop position,

lift the front pastthe stopposition and
slideout.

Fixed Freezer Shelves

Thereare two tgpes of fixed freezer shelves.

Toremove this type of shelf:

0 Lift the shelf up at the left side.
0 Bring the shelf out.

Toremove this type of shelf:

Make sure you push the baskets all the
way back in before you close the door.

Make sure you push the shelves all the way
back in before you close the door

NOTE FOR DISPENSER MODELS: In order to

take full advantage of the tilt-out ice bin, only
store items on the shelf below the ice bin that

are no toiler than the lowest point on the bin.

0

iijiiiii_Jiiiijjil

L_

° It"

Lift up the left side of the shelf and slideit
left into the center ofthe shelf supports.

Rotatethe right side of the shelf up
and out of the shelf supports.

Door Wine/Beverage Rack fan some models)

This rack holds up to 5 cans,one bottle

of wine or one 2-liter bottle of soda.
Therack hangs from the sides

of the dairg bin.

Toremove:

Emptg the wine/beverage rack.
Holdingthe bottom of the dairg bin,

lift the front straight up, then lift up
and out.

o Todetachtherackfromthedairybin

pull the rack's sidewires out ofthe holes
on each side of the dairy bin.

To replace:

Reattach the rack to the sides of the bin.
Engage the back side of the bin in

the molded supports on the dooE

Then push down on the front of

the bin. The bin willlock into place.

oo

€,n

¢b

o

About the refrigerator doors.

Refrigerator Doors

illii_

LL_

When the door is only partially open,
it will automatically close.

Beyond this stop the door will

stay open.

The refrigerator doors mag feel different than
the ones gou are used to. The special door

opening/closing feature makes sure the
doors close all the wag and are securelg

sealed.

When opening and closing the door gou will

notice a stop position. If the door is opened
past this stop point, the door will remain

open to allow gou to load and unload food
more easilg. When the door is onlg partiallg

open, it will automaticallg close.

Door Alignment

If doors are uneven, adjust

the refrigerator dooE

O Usinga 7/16" wrench, turn the door

adjusting screw to the right to raisethe
door,to the left to lower it.(Anglonplug,

imbedded in the threads of the pin,

preventsthe pin from turning unless

a wrench isused.)

The resistance gou feel at the stop position

will be reduced as the door is loaded
with food.

0 After oneor two turns of the wrench,

open and closethe refrigerator door
and check the alignment at the top

of the doors.

10

About the crispers and pans. ge.com

Not all features are on all models.

Fruit and Vegetable Crispers

Excesswater that mag accumulate in the

bottom of the drawers should be wiped dry.

On some models, the bottom drawer has
full extensionslidesthat allow full access
to the drawer

Q

e,,l,

O_

t_

0

#iiiii]iiii#

i'_iiiii_iiii#i

HI _ LO

Adjustable Humidity Crispers

Slidethe control all the wag to the HI setting
to provide high humidity recommended for

most vegetables.

Convertible Deli Pan

Theconvertible deli pan has its own cold

air duct to allow a stream of cold air from
the freezer compartment or fresh food

compartment to flow to the pan.

The variable temperature control regulates
the air flow from the Climate Keeper Air

Towe_:

About crisperremoval.

Slidethe control all the wag to the LO
setting to provide lower humidity levels

recommended for most fruits.

Setthe control to the coldest setting to store
fresh meats.

Setthe control to cold to convert the pan
to normal refrigerator temperature and

provide extra vegetable storage space.The
cold air duct isturned off.Variablesettings

between these extremes can be selected.

i_iii_ii,i,:>iiiii

......._m,,i,

to

g

Not all features ore on oil models.

Crisper Removal

Crisperscan easilg be removedbg pulling
the drawer straight out and lifting the drawer

up and over the stop location.

If the door prevents gou from taking out
the drawers,first trg to remove the door

bins. Ifthis doesnot offer enough clearance,
the refrigerator will needto be rolledforward

until the door opens enough to slide the
drawers out. Insome cases,when gou roll

the refrigerator out, gou will need to move
the refrigerator to the left or right as gou

roll it out.

t_

o

11

About the automatic icemaker.

A newly installed refrigerator may take 12 to 24 hours to begin making ice.

Automatic Icemoker

On dispenser models,
to access ice or reach

the power switch:

o Lift the bin, then pull it

forward until the bin stops.

o Lower the bin to access ice

or reach the power switch.

NOTE: In order to take full
advantage of the tilt-out ice bin,

only store items on the shelf below
the ice bin that are no taller than

the lowest point on the bin.

The icemakerwill produce seven cubes

per cycle-approximately 100-130cubes
in a 24-hour period,depending on freezer

compartment temperature, room

temperature, number of door openings

and other use conditions.
If the refrigerator is operated before the

water connection is made to the icemaker,

setthe power switch in the OFFposition.

When the refrigerator has been connected
to the water supply, set the power switch
to the ON position.

Theicemaker willfillwith water when it cools
to 15°F(-10°C).A newly installedrefrigerator

mag take 12to 24hoursto begin making
icecubes.

Youwill hear a buzzingsoundeach time
the icemaker fillswith water

Throw awag the first few batches of ice
to allow the water line to clear

Besure nothing interferes with the sweep
ofthe feeler arm.

When the bin fills to the levelof thefeeler

arm, the icemaker will stop producing ice.
It isnormal for several cubes to bejoined

together

If iceis not used frequently, oldicecubes will
become cloudy, taste stale and shrink.

Special note about dispenser models:

:_:_Dispenser models have a tilt-out ice bin.

:i:_Torestore your ice level from an empty

O 12 hours after the first batch of ice has

These stepswill restore your ice levelin

the shortest amount of time.

Switch FeelerArm

The bin can be tilted out as shown in the

illustrations, and it will hold itself upwhile

you take ice out or turn the icemaker
power switch on and off. Besureto put the

bin back in placebefore closing the dooE

bucket stage, the following steps are
recommended:

fallen into the bin,dispense Bto 4 cubes.
After an additional 6 hours, dispense

Bto 4 cubes again.

!cemaker

o Lift the bin. then oull it

forward until the bin stoos.

O Lift andpull forward again

to remove the bin.

12

Removing Ice Bin (dispenser models)

CAUTION:The ice bin is heavy when full....................................................................................................

Set the power switch to the OFFposition
before removing the bin.

When replacing the bin, be sure to press
it firmly into place. Ifit does not go all the

wag back, remove it and rotate the drive

mechanism 1/4 turn. Then push the bin
back again.

Dispenser Models only

About the ice and water dispenser. Ionsomemodds) ge.com

To Use the Dispenser

SpillShelf

SelectCUBEDICE,CRUSHEDICEorWATER.

Presstheglassgentlyagainstthetop ofthe
dispensercradle.

Thespillshelfisnot self-draining.Toreducewater
spotting,theshelfanditsgrilleshouldbecleaned

regularlg.

Ifnowaterisdispensedwhentherefrigeratoris

firstinstalled,theremaybeairinthewaterline
system.Pressthedispenserarmfor atleasttwo
minutestoremovetrappedairfromthewaterline
andtofill thewatersystem.Toflushoutimpurities
in thewaterline,throwaway thefirstsixglassfuls

of water.

CAUTION:Neverputfingersorany otherobjects
intotheicecrusherdischargeopening.

Locking the Dispenser

PresstheLOCKpadfor 3secondsto lockthe
dispenserandcontrolpanel.Tounlock,press
and holdthepadagainfor 3 seconds.

Precise Fill

DispenserLight

TheLIGHTpadturnsthenight light inthe
dispenseron andoff.Thelightalsocomeson
whenthe dispensercradleispressed.Onsome
models,ifthis lightburnsout,it shouldbereplaced

witha Bwatt 12Vmaximumbulb.

Quick Ice

Whenyouneediceina hurrg,presstheQUICK
ICEpadto speedupice production.Thiswill
increaseiceproductionforthefollowing48hours
or untilgoupressthe padagain.

Door AIorm

Tosetthealarm,presstheDOORALARMpaduntil
theindicatorlightcomeson.Thisalarmwill sound
ifeitherdoorisopenfor morethan 3minutes.
Thelightgoesoutandthebeepingstopswhen
gouclosethedoor.

t_

0

iijiiiii_]iiiijjil

i'_ii[ii_iiiiii_l

Thiswaterdispenseris equippedwith afeature

called"precisefill."Thisfeatureallowsyouto
choosea preciseamountof water(cupsor
ounces)that gouwouldlikedispensed.

0 Pressthe WATERpad.
0 Pressthe CUPSor OUNCESpad.

Selectthe preciseamountofwatergou
wouldlikedispensed.

Ifyou selectedOUNCES,pressthearrow

padsoneithersideofthedisplagtoselect
the numberofouncesgouwouldliketo have
dispensedbetween1-99ounces.

Ifyou selectedCUPS,pressthearrowpads
on theleftofthedisplagtoselectthewhole
cups(1-16cups)and/orthearrowpadson
the rightsideofthe displagto selectfractions
of acup(1/4-3/4cups).

Important Facts About Your Dispenser

i;__Donotaddicefrom tragsor bagsto

thestoragedrawer.Itmag notcrushor

dispensewell.

i_ Avoidoverfillingglasswithiceanduseof

narrowglasses.Backed-upicecanjam the
chuteorcausethedoorinthe chuteto freeze

shut.Ificeisblockingthechute,pokeitthrough
withawoodenspoon.

i;_Beveragesandfoodsshouldnotbequick-

chilledintheicestoragedrawenCans,bottles
orfoodpackagesinthestoragedrawermag
causetheicemakeroraugertojam.

:_Tokeepdispensedicefrommissingtheglass,

putthe glasscloseto,butnottouching,the
dispenseropening.

Pressthe cupagainstthecradleandwater
willbegindispensing.Itwillautomaticallg

stopwhentheamountsethasbeen
dispensed.Thedisplagwillshowthere
isnowater leftto dispense,then reset.

NOTE:Donotleavethedispenserunattended
whenwateris beingdispensed.

If youwouldliketostopdispensingwater
beforethespecifiedamounthasbeen

dispensed,justremovethe cupfromthe
cradle.Thedisplagwillshowthe amount

lefttodispense.

i;_Somecrushedicemagbedispensedeven

thoughgouselectedCUBEDICE.Thishappens

occasionallgwhen afewcubesaccidentallyget
directedtothe crushe[

iqAftercrushediceisdispensed,somewatermag

dripfromthechute.

i;_Sometimesa smallmoundof snowwillform

onthedoorinthe icechute.Thisconditionis
normalandusuallgoccurswhengouhave

dispensedcrushedicerepeatedlg.Thesnow

willeventuallyevaporate.

13

t_

:b-

oo

€'b
o

Careand cleaning of the refrigerator.

Cleaning the Outside

Dispenser drip area.

Thedispenser drip area, beneaththe grille,

shouldbe wipeddry.Water left in this area
may leave deposits.Remove the deposits

bg adding undiluted vinegar to the well. Soak
until the deposits disappear or become loose

enough to rinseaway.
Thedispenser cradle. Beforecleaning,

lock the dispenser bg pressing and holding

the LOCKpad for 3 seconds.Cleanwith
warm water and baking soda solution-

about a tablespoon (15ml) of bakingsoda

to a quart (1 liter)of water. Rinsethoroughly

and wipe dry.
Thedoor handles and trim. Clean with

a cloth dampened with soapy water.
Drgwith a soft cloth.

Cleaning the Inside
To help prevent odors, leave an open box

of baking soda in the fresh food and freezer
compartments.

Unplug the refrigerator before cleaning.

Ifthis is not practical, wring excess moisture
out of sponge or cloth when cleaning around

switches, lights or controls.
Use warm water and baking soda solution-

about a tablespoon (15 ml) of baking soda to
a quart (1 liter)of water. This both cleans and

neutralizes odors. Rinse and wipe dry.

Use of any cleaning solution other than

that which is recommended, especially
those that contain petroleum distillates,

can crock or damage the interior of the
refrigerator.

The stainless steel panels and door handles

(on some models) can be cleaned with
a commercially available stainless steel

cleaner. A sprag-on stainless steel cleaner
works best.

Do not useappliance wax or polish
on the stainlesssteel.

Keep the outside clean. Wipe with a
clean cloth lightly dampened with kitchen

appliance wax or mild liquid dish detergent.
Dry and polish with a clean, soft cloth.

Do not wipe the refrigerator with a soiled
dish cloth or wet towel. These may leave

a residue that can erode the paint. Do not
use scouring pods, powdered cleaners,

bleach or cleaners containing bleach
because these products can scratch

and weaken the point finish.

Avoid cleaning cold glass shelves with hot

water because the extreme temperature
difference may cause them to break.

Handle gloss shelves carefully. Bumping
tempered gloss can cause it to shatter.

Do not wash any plastic refrigerator ports
in the dishwasher.

Thechill/thaw tra_l is dishwasher safe.

14

Behind the Refrigerator

Becareful when moving the refrigerator
away from the wall.All types of floor

coveringscan be damaged, particularly
cushioned coverings and those with

embossedsurfaces.
Pullthe refrigerator straight out and return

itto position by pushing it straight in. Moving
the refrigerator in a sidedirection may result

in damage to the floor covering or
refrigeratoE

Preparing for Vacation

Forlong vacations or absences,remove
food and unplug the refrigerator. Clean

the interior with a baking soda solution of
one tablespoon (15ml) of baking sodato one

quart 11liter)of wateE Leavethe doors open.
Setthe icemaker power switch to the OFF

position and shut off the water supply to
the refrigeratoE

ge.com

When pushing the refrigerator back, make
sure you don't roll over the power cord or

icemaker supply line.

If the temperature can drop below freezing,
have a qualified servicer drain the water

supply system to prevent serious property
damage due to flooding.

r",l,

0

iiiiiiii_Jiiiiiiil

i_iii_ii,i,::,iiiii

Preparing to Move

Secureoil looseitems such as shelvesand
drawers by taping them securely in place
to prevent damage.

When using a hand truck to move the
refrigerator,do not rest the front or back
of the refrigerator against the hand truck.

This could damage the refrigerator.Handle

only from the sidesof the refrigeratoE

Be sure the refrigerator stays in an upright
position during moving.

L_

oo

o

15

R

Replacingthe light bulbs.

Setting the controls to OFF does not remove power to the light circuit.
Reveal ®appliance bulbs ore used on some models. They can be identified by their blue color when they

ore not illuminated.
Not oil features ore on oil models.

Your light shield will look like
one of the following:

Tabs

OR

Pocket

Refrigerator Compartment--Upper Light

0 Unplug the refrigeratoE

Thebulbs are located at the top of
the compartment, insidethe light shield.
On some models, a screw at the front

of the light shieldwill have to be

removed.On other models,

the screw is located in the pocket

located at the back of the light shield.

Toremove the light shield,on some

models,pressin on the tabs on the sides

of the shield and slideforward and out.
On other models,just slidethe shield

forward and out.

Refrigerator Compartment--Lower Light

This light is located above the top drawer.

Unplugthe refrigerator`
Removethe convertible meat drawer

control knob bg pullingstraight out.

After replacing the bulb with an
appliance bulb of the same or lower

wattage, replace the light shieldand
screws (on some models).When

replacingthe light shield,make
surethat the tabs at the back
of the shieldfit into the slots at

the back of the light shieldhousing.

Plugthe refrigerator back in.

After replacing the bulb with an
appliance bulb of the same or lower

wattage, replace the shieldand the knob.

Plug the refrigerator back in.

16

Liftthe light shieldup and pull it out.

Freezer Compartment

Unplugthe refrigerator.

0 Removethe shelfjust abovethe light

shield.(Theshelfwill be easierto remove
if it isemptied first.) On some models,

a screw at the top ofthe light shield
will need to be removed.

Toremove the light shield,pressin
on the sides,and lift up and out.

Dispenser (on some models)

Unplugthe refrigerator`

Thebulb islocated on the dispenser

under the control panel. Removethe light
bulb bg turning it counterclockwise.

Replace the bulb with an appliance

bulb of the same or lower wattage,
and reinstall the light shield. When

reinstalling the light shield, make sure
the top tabs snap securelg into place.

Replace the screw (on some models).

Reinstall the shelf and plug
the refrigerator back in.

Replace the bulb with a bulb
of the same size and wattage.

Plug the refrigerator back in.

Trim kits and decorator panels.

For CustomStgld" models

Read these instructions completely and carefully.

Before You Begin

Some models ore equipped with trim kits that allow you to install door panels. You con order
pre-cut block, white, bisque or stainless steel decorator panels from GE Ports and Accessories,

800.626.2002, or you con odd wood panels to match your kitchen cabinets.

Panels less than 1/4" (6 mm) thick

When installing wood panels less then 1/4" (6 mm) thick, you need to create a filler panel, such as 1/8"
cardboard, that will fit between the face of the door and the wood panel, If Uou are installing the pre-cut

decorator panels, pre-cut filler panels are included in the kit, The combined thickness of the decorator
or wood panel and the filler panel should be 1/4" (6 mm),

Panels1/4"thickor less

i/4" max

3/4" (19 mm) or Raised Panel

A raised panel design screwed or glued to a 1/4" (6 mm) thick backing, or a 3/4" (19 mm) routed board can
be used. The raised portion of the panel must be fabricated to permit clearances of at least 2" (5.1cm) from

the handle side for fingertip clearance.
Panels thicker than 1/4" (6 mm), up to 3/4" (19 mm) max, will require that the outer 5/16" (8 mm) of panel

perimeter be no thicker than 1/4" (6 mm).

Weight limitations for custom panels:
Fresh Food38 lbs. (17 kg) max.

Freezer Door 28 lbs. (13 kg) mex.

Panelsthicker than 1/4" (6 mm)

5/16" (8 ram)

1/4" (6mm)

Thick Backing

¢"

2" (5.1 cm)
Clearance

1/4"(6 mm) max

3/4"(19mm)

Handle Side

Appearance
Panel

(19 mm)

Refrigerator
Door

17

(

|

(

°.

(

i

(

|

4

1

m

(

|

.!

(

i

(

|
1

|
1

L

(

|

C

Trim kits and decorator panels.

23' Dimensions for Custom Wood Panels

The areas at the top of the panels need to be cut out of the panels,

Freezer Panel Freezer Panel

Without Dispenser With Dispenser

Cutout ---, I_,.- 1/8" (3 mm)

.... J ,

Cutout --,-_ _-1/8" (3 mm)

',

i i

t

5/16"

(8ram)

18ram/|/

| 177/8"

II ?cm'

m

6P/s/"

{170.9 cm)

FRONT

I FRONT

Fresh Food Panel

1/8" (3 mm) "-_l I'- Cutout

',',..._!s/16"

I....1 (8 ram)

679/3Z'

(170.9 cm)

FRONT

4-- (36.8 cm) °

141s/s/' _

|(36.8 cm)

33_/8"

(85.4 cm)

19_5/s/'

_'(49.5 cm) "-_

I

25' CustDmStyle TM Dimensions for Custom Wood Panels

The areasat the top of the panels needto be cut out of the panels,

(

1

1
|

°.

(
(

.4

(

.4

Freezer Panel

Without Dispenser

Cutout --_I 14- 1/8" (3 mm)

.... J

''

, !

t

5/16"

(8 ram)

FreezerPanel

With Dispenser

Cutout --"l I"-1/8" (3 mm)

',

i i

/8mm/|/

FreshFoodPanel

1/8" (3 mm).-_ I I'- Cutout

', ',___! 5/16"
I-

---_ (8 ram)

i

(

|
1

L

(

1

|

(

L

69"

(175.3 cm)

FRONT

._ 14_s/s2" -,,-

'(56.8 cm)

i FRONT

14_%2" .

(36.8 cm)

36V_"

(92.0 cm)

69"

(175.5 cm)

FRONT

19_s/s2"

"(49.5 cm)" "-"

18

Inserting the door panels.

Read these instructions completely and carefullg.

0 Insert the Freezer Panel and Fresh Food Panel.

Carefully push the freezer panel in until it slidesinto If your model has a dispenser,thissteponly applies
the slot behind the door handle.Pushthe filler panel to the fresh food panel and top freezer panel.

(requiredwith some door panels)in behind the
decorator panel. Repeatfor fresh food panel.

0 Insert the Bottom Freezer Panel (an dispenser models).

Carefully push the panel in until it slidesinto the slot with some door panels)in behind the decorator panel.

behind the door handle. Pushthe filler panel (required

Attach the Top Trim on the Freezer and Fresh Food Doors.

TheTopTrim can be found insidethe refrigerator each dooEHandtighten only. Make surethat
compartment, the top of eachpanel fits snugly behind the lip

With a T-20Tar×driver,attach the TopTrim,using ofthe TopTrim.
two screws on each TopTrimpiece,to the top of

Cut-Out

Side Trim

t

19

|

(

°.

Inserting the door panels.

i

|

4

(

O Install the Side Trim.

Thesepieces are tucked insidethe refrigerator
door handle.

Do not remove the protective film on the outside
of the Side Trim until the Side Trim is instolled.

Holdthe SideTrim against the front face
of the decorator panels and fit the SideTrimunder

theTop Trim. Hake sure the magneticall9 attached
SideTrim isfitted correctl9 andthat 9ou are satisfied

with the appearance of all the parts.

Fitthe bottom of the SideTrim under the Bottom Trim

m

|

as illustrated.

.!

i

|

(

|

L

(

|

C

"4

,4

€

(

|

°.

(
(

€

1

(

|

L

(

1

i

|

(

20

Installation

Refrigerator

Instructions

I Questions? Call 800.GE.CARES (800.432.2737) or Visit our Website at: ge.com

BEFORE YOU BEGIN

Read these instructions completely
and carefully.

IMPORTANT - savetheseinstructions

for local inspector's use.

IMPORTANT - Observeallgoverninc

codes and ordinances.

• Note to Installer - Be sure to leave these
instructions with the Consumer.

• Note to Consumer- Keep these instructions
for future reference.

• Skill level -Installation of this appliance requ,res
basic mechanical skills.

In Canada, call 2.800.561.3344 or Visit our Website at: geappliances.ca

PREPARATION

WATER SUPPLY TO THE ICEMAKER

connected to a cold water line. AGE water supplg
kit (containing tubing, shutoff valve, fittings and
instructions) is available at extra cost from gour
dealer, bg visiting our Website at ge.com (in Canada
at geappliances.ca) or from Parts and Accessories,

800.626.2002 (in Canada 1.800.661.1616).

TOOLS YOU WILL NEED

Models 23, 25, 26, 27 & 29

If the refrigerator has an icemaker, it will have to be

I

• Completion time- Refrigerator Installation

30 minutes
Water Line Installation

30 minutes

• Proper installation is the responsibilitg
of the installer.

• Product failure due to improper installation
is not covered under the Warrantg,

If the refrigerator has already been installed,
remove the base grille (see Step 2 in Moving

the Refrigerator), then skip to Step 5 in Installing
the Refrigerator.

3/8" and 5/16" Socket

1/8" Hex Wrench

Phillips Head Screwdriver

1/2" and 7/16" Wrench

]

U

Plastic Puttg Knife

21

Installation Instructions

MOVING THE REFRIGERATOR

[] LOADING THE REFRIGERATOR

ONTO A HAND TRUCK

Leave all tape and door pads on doors until

the refrigerator is in its final location.
To move the refrigerator, use a padded hand

truck. Center the refrigerator on the hand truck
and secure the strap around the refrigerator.

DO NOT OVERTIGHTEN THE STRAP.

If the refrigerator must go through

ong entrance that is less than 38" wide,
the doors must be removed. Proceed to

Step 3.
DO NOT remove the handles.

If all entrances are more than 38" wide,

skip to Installing the Refrigerator.

[] DISCONNECT THE WATER COUPLING

(on some models}

If the refrigerator has a water dispenser,
there is a water line from the cabinet into

the bottom hinge on the freezer door that
must be disconnected.

To disconnect, push in on the white collar
of the coupling and pull out the tubing.

White collar

[] REMOVE THE BASE GRILLE

Remove the grille by removing the two Phillips

head screws.

Bottom

freezer
hinge

22

Installation Instructions

[] DISCONNECT THE POWER COUPLING

(on some models)

If the refrigerator has a water dispenser,
there is a power line (harness) from the cabinet
into the bottom hinge on the freezer door that

must be disconnected.
To disconnect pull apart at the coupling.

Bottom _ _ LJ o _/'J

freeze,- ! _ -'-'L--"a_J------------

hin

[] DISCONNECT THE ELECTRICAL

CONNECTORS (on some models)

If the refrigerator has a refreshment center,
there are electrical connectors (harnesses)

from the cabinet into the bottom hinge
on the refrigerator door that must be

disconnected.
To disconnect, pull apart each connecton

[] CLOSE THE FREEZER AND

REFRIGERATOR DOORS

[] REMOVE THE FREEZER DOOR

[] Remove the freezer door top hinge cover

(if equipped) bg either squeezing it and pulling
it up or bg prging it off with a plastic puttg

knife.

[] Remove the two 5/16" or 1/8" hex head

screws, then lift the hinge straight up to free
the hinge pin.

5/16" or 1/8" hex head

Bottom
refrigerator

hinge

[] Open the freezer door to 90.°

r_

90°

23

Installation Instructions

MOVING THE REFRIGERATOR(CONT.)

[] REMOVE THE FREEZER DOOR (cont.)

[] As one person slowlg lifts the freezer door up

and off the bottom hinge, the second person
should carefullg guide the water line and power
line (harness) through the bottom hinge.

_

90°

[] Set the door on a non-scratching surface with

the inside up.

[] REMOVE THE REFRIGERATOR DOOR

[] Remove the refrigerator door top hinge

cover (if equipped) bg either squeezing it and
pulling it up or bg prging it off with a plastic
puttg knife.

[] REMOVE THE REFRIGERATOR DOOR

(cont.)

[] Remove the two 5/16" or 1/8" hex head

screws, then lift the hinge straight up to free

the hinge pin.

5/16" or 1/8" hex head

<

[] Open the refrigerator door to 90.°

_ H

90°

24

Installation Instructions

[] REMOVE THE REFRIGERATOR DOOR

(cont.)

[] Lift the refrigerator door up and off the bottom

hinge.
If the refrigerotor hos o refreshment center,

one person should slowly lift the door up and
off the bottom hinge and the second person
should carefully guide the electrical lines
(harnesses) through the bottom hinge.

90°

Refreshment Center Models Only

[] Set the door on a non-scratching surface with

the inside up.

[] REPLACING THE DOORS

To replace the doors, simplg reverse
steps 3 through 8,

However, please note the following:

• When lowering the doors onto the bottom
hinges, make sure the second person
carefully guides the tube and harnesses
through the holes in the hinges.

• When connecting the water line, make sure
you insert the tubing all the way to the mark.

L

Hark

• Do not pinch the tubing and harnesses when
placing the doors on the bottom hinges,

• When connecting the power line and the
electrical lines (refreshment center models

only), be sure that the connectors are seated
together fullg,

25

Installation Instructions

INSTALLING THE REFRIGERATOR

REFRIGERATOR LOCATION

• Do not install the refrigerator where the
temperature will go below 60°F (16°C) because
it will not run often enough to maintain proper

temperatures.

• Do not install the refrigerator where the
temperature will go above 100°F (37°C) because
it will not perform properlg.

• Install it on a floor strong enough to support it
fullg loaded.

CLEARANCES

Allow the following clearances for ease
of installation, proper air circulation and plumbing

and electrical connections:

23' (33" wide},

23'/25' CustomStyle T" 25', 26', 27', 29'

Sides 1/8" (4 mm) 1/8" (4 mm)

Top 1" (25 mm) 1" (25 mm)

Back 1/2" (13 mm) 1" (25 mm)

DIMENSIONS AND SPECIFICATIONS

{for 23' CustomStyle" models}

70_" {178.4 cm)

o

_" 36"_

(91.4 cm}

24" (61 cm}_

\ h

DIMENSIONS AND SPECIFICATIONS

{for 25' CustomStyle TM models}

DIMENSIONS AND SPECIFICATIONS

Electrical

(19mm)

Airspace

24" (61 cm)

(1/2" [13 mm] Gap +

1/4" [6 mm] Wall

Plates)

Countertop

' J'L

o o

....... ........

72]/4" (183.5 cm)*

o

o

"721/4" (183.S cm) required for full adjustment

of mobilitg wheels, If cabinets installed above
refrigerator have doors that are flush to the top of

the opening for the refrigerator, then an additional

1/8" mag be required to provide clearance for
cabinet doors to open freelg.

26

Installation Instructions

[] CONNECTING THE REFRIGERATOR

TO THE HOUSE WATER LINE
(icemaker and dispenser models)

A cold water supply is required for automatic
icemaker and dispenser operation. If there
is not a cold water supply, you will need to
provide one. See Installing the Water Line

section.
NOTES:

• Before making the connection to the
refrigerator, be sure the refrigerator power
cord is not plugged into the wall outlet.

• If your refrigerator does not have a water
filter, we recommend installing one if your
water supply has sand or particles that could
clog the screen of the refrigerator's water

valve. Install it in the water line near the
refrigerator. If using GESmartConnect TM

Refrigerator Tubing Kit, you will need an

additional tube (WXO8XIO002) to connect
the filter. Do not cut plastic tube to install

filter.

[] If gou are using copper tubing, place a

compression nut and ferrule (sleeve) onto
the end of the tubing coming from the house
cold water supply.

If gou are using the GE SmartConnect"
tubing, the nuts are already assembled to
the tubing.

[] If you are using copper tubing, insert

the end of the tubing into the refrigerator
connection, at the back of the refrigerator,
as far as possible. While holding the tubing,
tighten the fitting.

If gou are using GE SmartConnect TM tubing,
insert the molded end of the tubing into the
refrigerator connection, at the back of the
refrigerator, and tighten the compression
nut until it is hand tight. Then tighten one
additional turn with a wrench. Overtightening
may cause leaks.

[] Fasten the tubing into the clamp provided to

hold it in position. You may need to pry open
the clamp.

1/4"

Compression Nut

(sleeve)

Refrigerator
Connection

SmartConnect " Tubing

[] TURN ON THE WATER SUPPLY

Turn the water on atthe shutoff valve
(house water supply) and check for any leaks.

[] PLUG IN THE REFRIGERATOR

Before plugging in the refrigerator, make sure
the icemaker power switch is set to the OFF
position.

27

See the grounding information attached
to the power cord.

Installation Instructions

INSTALLING THE REFRIGERATOR(CONT.}

[] PUT THE REFRIGERATOR IN PLACE

Hove the refrigerator to its final location.

[] LEVEL THE REFRIGERATOR

The refrigerator can be leveled bg adjusting
the rollers located near the bottom hinges.

Rollers have three purposes:

• Rollers adjust so the door closes easily when
opened about halfway. (Raise the front about

5/8" [16 mm] from the floor.)

• Rollers adjust so the refrigerator is firmly
positioned on the floor and does not wobble.

• Rollers allow gou to move the refrigerator
awag from the wall for cleaning.

To adjust the rollers on 23' (33" wide}, 25', 26',

27' end 29' models:

Turn the roller
adjusting screws

clockwise to raise
the refrigerator,

counterclockwise
to lower it. Use

a 3/8" hex socket
or wrench, or

an adjustable
wrench.

Raise

[] LEVEL THE REFRIGERATOR

(cont.}

To adjust the rollers on 23'/25' CustomStgle"
models:

Turn the front roller
adjusting screws

clockwise to raise
the refrigerator,

cou nterclockwise
to lower it. Use a

3/8" hex wrench
with extension, or

an adjustable wrench.
These models also have rear adjustable rollers

so gou can align the refrigerator with gour
kitchen cabinets. Use a 3/8" hex wrench with

extension to turn the screws for the rear rollers-
clockwise to raise the refrigerator,

counterclockwise to lower it.

[] LEVEL THE DOORS

Adjust the refrigerator door to make the doors
even at the top.

To align:

[]

Using a 7/16" wrench, turn the door adjusting

screw to the right to raise the door, to the left
to lower it.

NOTE:
A nglon plug, imbedded in the threads

of the pin, prevents the pin from turning unless
a wrench is used.

[]

After one or two turns of the wrench, open
and close the refrigerator door and check
the alignment at the top of the doors.

Doors should be even at top

Roller adjusting screws

Roller adjusting screw

28

Installation Instructions

[] REPLACE THE BASE GRILLE

Replace the grille bg installing the two Phillips

head screws.

[] START THE ICEMAKER

Set the icemaker power switch to the ON
position. The icemaker will not begin to operate
until it reaches its operating temperature
of 15°F (-9%) or below. It will then begin
operation automaticallg. It will take 2-3 dags

to fill the ice bin.

sw,tch_

[] SET THE CONTROLS

Set the controls to the recommended setting,

5 5

bCOMME°OEOCO°'ROLSsl

0 _FISRECOMMENDED 37 "FIS RECOMMENDED

29

Installation Instructions

INSTALLING THE WATER LINE (ICEMAKER &.DISPENSER MODELS)

BEFORE YOU BEGIN

Recommended copper water supply kits are WX8X2,
WX8X] or WX8X4, depending on the amount of tubing
you need. Approved plastic water supply lines are GE
SmartConnect T"Refrigerator Tubing (WX08X10002,

WX08X10006, WX08X10015 and WX08X10025).
When connecting your refrigerator to a GEReverse

Osmosis Water System, the only approved installation
is with a GE RVKit. For other reverse osmosis water

systems, follow the manufacturer's recommendations.

If the water supply to the refrigerator is from
a Reverse Osmosis Water Filtration System
AND the refrigerator also has a water filter,
use the refrigerator's filter bypass plug. Using
the refrigerator's water filtration cartridge in
conjunction with the ROfilter can result in hollow

ice cubes and slower water flow from the water
dispenser.
This water line installation is not warranted by

the refrigerator or icemaker manufacturer. Follow
these instructions carefully to minimize the risk
of expensive water damage.

Water hammer (water banging in the pipes)in
house plumbing can cause damage to refrigerator
parts and lead to water leakage or flooding. Call a
qualified plumber to correct water hammer before
installing the water supply line to the refrigeraton

To prevent burns and product damage, do not hook
up the water line to the hot water line.

If you use your refrigerator before connecting
the water line, make sure the icemaker power
switch is in the OFF position.

Do not install the icemaker tubing in areas where
temperatures fall below freezing.

When using any electrical device (such as a power
drill) during installation, be sure the device is double
insulated or grounded in a manner to prevent the
hazard of electric shock, or is battery powered.
All installations must be in accordance with local

plumbing code requirements.

WHAT YOU WILL NEED

J

• Copper or GE SmartConnect TM Refrigerator
Tubing kit, 1/4" outer diameter to connect the

refrigerator to the water supply. If using copper,
be sure both ends of the tubing are cut square.

To determine how much tubing you need:
measure the distance from the water valve

on the back of the refrigerator to the water supply
pipe. Then add 8' (2.4 m). Be sure there is sufficient
extra tubing (about 8' [2.4 m] coiled into 3 turns

of about 10" [25 cm] diameter) to allow the
refrigerator to move out from the wall after

installation.
GE SmartConnect T' Refrigerator Tubing Kits are

available in the following lengths:
2' (0.6 m) - WX08X10002

6' (1.8 m) - WX08X10006
15' (4.6 m) - WXO8X10015
25' (7.6 m) - WXO8X10025

Be sure that the kit you select allows at least
8' (2.4 m) as described above.

3O