GE GSE23GGKCC User Manual
Safety Instructions .................2–3
Operating Instructions
Automatic Icemaker ..................12,13
Care and Cleaning ...................15,16
Crispers and Pans .......................11
ExpressChill
Ice and Water Dispenser ................14
Refrigerator Doors ......................10
Replacing the Light Bulbs .............16,17
Shelves and Bins .......................8, 9
Temperature Controls ....................4
TurboCool
Side by Side
ClimateKepper2 ..........................5
Water Filter ..............................7
Installation Instructions
Installing the Refrigerator ............ 23–26
Moving the Refrigerator .............19–22
Preparing to Install
the Refrigerator .........................18
Water Line Installation ..............27–29
Troubleshooting Tips ............31–33
Normal Operating Sounds ...............30
Consumer Support
Consumer Support .............Back Cover
Performance Data Sheets ............34,35
Warranty ...............................36
™
™
.............................5
..............................5
Owner’s Manual
and Installation
Models 22, 23, 25,26,27 and 29
Côte à Côte
Réfrigérateurs
Manuel d’utilisation
et d’installation
La section française commence à la page 40
Lado a Lado
Refrigeradores
Manual del propietario
e instalación
La sección en español empieza en la página 75
Write the model and serial numbers here:
Model # _________________________
Serial # __________________________
Refrigerators
Find these numbers on a label inside the
refrigerator compartment at the top on the
right side.
200D8074P051 49-60646-5 05-16 GE
IMPORTANT SAFETY INFORMATION.
READ ALL INSTRUCTIONS BEFORE USING.
GE Appliances Website
For more information on your refrigerator’s operation, visit www.GEAppliances.com or
call 800.GECARES (800.432.2737). In Canada visit GEAppliances.ca or call 800.561.3344.
REFRIGERATOR SAFETY INFORMATION
This is the safety alert symbol. This symbol alerts you to potential hazards that can kill or hurt you and others. All
safety messages will follow the safety alert symbol and the word “DANGER”, “WARNING”, or “CAUTION”. These words are
defined as:
DANGER
Indicates a hazardous situation which, if not avoided, will result in death or serious injury.
WARNING
Indicates a hazardous situation which, if not avoided, could result in death or serious injury.
CAUTION
Indicates a hazardous situation which, if not avoided, could result in minor or moderate injury.
IMPORTANT SAFETY INSTRUCTIONS
WARNING
This refrigerator must be properly installed and located in
accordance with the Installation Instructions before it is used.
Unplug the refrigerator before making repairs, replacing a light
bulb, or cleaning.
Note: Power to the refrigerator cannot be disconnected by any
setting on the control panel.
Note: Repairs must be performed by a qualified service
professional.
Replace all parts and panels before operating.
Do not store or use gasoline or other flammable vapors and
liquids in the vicinity of this or any other appliance.
To reduce the risk of fire, explosion, electric shock, or injury when using your
refrigerator follow these basic safety precautions:
Because of potential safety hazards under certain conditions,
we strongly recommend against the use of an extension cord.
However, if you must use an extension cord, it is absolutely
necessary that it be a UL-listed (in the United States) or a CSA
certified (in Canada), 3-wire grounding type appliance extension
cord having a grounding type plug and outlet and that the electrical
rating of the cord be 15 amperes (minimum) and 120 volts.
To prevent suffocation and entrapment hazards to children,
remove the fresh food and freezer doors from any refrigerator
before disposing of it or discontinuing its use.
Do not allow children to climb, stand or hang on the door
handles or the shelves in the refrigerator. They could seriously
injure themselves.
State of California Proposition 65 Warnings:
WARNING
CAUTION
Do not clean glass shelves or covers with warm water
when they are cold. Glass shelves and covers may break if
exposed to sudden temperature changes or impact, such
as bumping or dropping. Tempered glass is designed to
shatter into many small pieces if it breaks.
Keep fingers out of the “pinch point” areas; clearances
between the doors and between the doors and cabinet are
necessarily small. Be careful closing doors when children
are in the area.
2
This product contains one or more chemicals known to the State of California to cause cancer and birth
defects or other reproductive harm.
IMPORTANT SAFETY INSTRUCTIONS
To reduce the risk of injury when using your refrigerator, follow these basic
safety precautions.
Do not touch the cold surfaces in the freezer compartment
when hands are damp or wet, skin may stick to these
extremely cold surfaces.
Do not refreeze frozen foods which have thawed
completely.
In refrigerators with automatic icemakers, avoid contact
with the moving parts of the ejector mechanism, or with the
heating element that releases the cubes. Do not place fingers
or hands on the automatic ice making mechanism while the
refrigerator is plugged in.
GEAppliances.com
INSTALLATION
WARNING
Explosion Hazard.
Keep flammable materials and vapors, such as gasoline, away from refrigerator. Failure to do so can
result in fire, explosion, or death.
CONNECTING ELECTRICITY
WARNING
Plug into a grounded 3-prong outlet
Do not remove the ground prong
Do not use an adapter
Failure to follow these instructions can result in death, fire, or electrical shock.
Electrical Shock Hazard.
Do not, under any circumstances, cut or remove the third (ground) prong from the power cord.
For personal safety, this appliance must be properly grounded.
The power cord of this appliance is equipped with a
3-prong (grounding) plug which mates with a standard
3-prong (grounding) wall outlet to minimize the
possibility of electric shock hazard from this appliance.
Have the wall outlet and circuit checked by a qualified
electrician to make sure the outlet is properly
grounded.
Where a standard 2-prong wall outlet is encountered,
it is your personal responsibility and obligation to have
it replaced with a properly grounded 3-prong wall
outlet. Do not use an adapter.
The refrigerator should always be plugged into its own
individual electrical outlet which has a voltage rating
that matches the rating plate.
A 115 Volt AC, 60 Hz, 15- or 20-amp fused, grounded
electrical supply is required. This provides the best
performance and also prevents overloading house
wiring circuits which could cause a fire hazard from
overheated wires.
Never unplug your refrigerator by pulling on the power
cord. Always grip plug firmly and pull straight out from
the outlet.
Repair or replace immediately all power cords that
have become frayed or otherwise damaged. Do not
use a cord that shows cracks or abrasion damage
along its length or at either end.
When moving the refrigerator away from the wall, be
careful not to roll over or damage the power cord.
PROPER DISPOSAL OF YOUR OLD REFRIGERATOR
WARNING
Remove fresh-food and freezer doors from the refrigerator, prior to disposal. Failure to do so can
result in child entrapment which can lead to death or brain damage.
IMPORTANT:
Suffocation and child entrapment hazard.
Child entrapment and suffocation are not problems
of the past. Junked or abandoned refrigerators are
still dangerous even if they will sit for “just a few
days.” If you are getting rid of your old refrigerator,
please follow the instructions below to help prevent
accidents.
Before You Throw Away Your Old Refrigerator or
Freezer:
Take off the fresh food and freezer doors.
Leave the shelves in place so that children may
not easily climb inside.
Refrigerants
All refrigeration products contain refrigerants,
which under federal law must be removed prior
to product disposal. If you are getting rid of an old
refrigeration product, check with the company
handling the disposal about what to do.
READ AND FOLLOW THIS SAFETY INFORMATION CAREFULLY.
SAVE THESE INSTRUCTIONS
3
About the temperature controls.
Not all features are on all models. Your controls may be similar to the following:
OR
The temperature controls are preset in the factory at 37°F for the refrigerator compartment and
0°F for the freezer compartment. Allow 24 hours for the temperature to stabilize to the preset
recommended settings.
The temperature controls can display both the SET temperature as well as the actual temperature
in the refrigerator and freezer. The actual temperature may vary slightly from the SET temperature
based on usage and operating environment.
On some models, setting both controls to the warmest setting until the display flashes (off) will
stop cooling in both the freezer and refrigerator compartments.
On other models, setting either control to the warmest setting until the display flashes (off) will
stop the cooling to the freezer and refrigerator.
NOTE: Turning the refrigerator off via the controls on the touch panel does not shut off electrical
power to the refrigerator.
NOTE: The refrigerator is shipped with protective film- covering the temperature controls. If this film
was not removed during installation, remove it now.
Performance Air Flow System
The Performance Air-Flow System is designed
to maximize temperature control in the
refrigerator and freezer compartments. This
unique special feature consists of the Air
Tower along the back wall of the refrigerator
and the Air Tunnel on the bottom portion of
the freezer rear wall.
4
Placing food in front of the louvers on these
components will not affect performance.
Although the Air Tower and the Air Tunnel can
be removed, doing so will affect temperature
performance. (For removal instructions,
on-line, 24 hours a day, contact us at
GEAppliances.com or call 800.GE.CARES. In
Canada, contact us at geappliances.ca or call
1.800.561.3344.)
About ClimateKeeper2.
How it Works
The ClimateKeeper2™ is the industry’s most
advanced refrigeration system, delivering
optimum temperature and humidity
performance to keep food garden fresh
longer and reduce freezer burn.
The ClimateKeeper2™ system features two
HYDSRUDWRUV³RQHIRUWKHUHIULJHUDWRUDQGRQH
for the freezer.
This provides two separate cooling systems,
and separates the airflow between the fresh
food and freezer compartments during
normal cooling operations.*
This ensures that the humidity levels in the
fresh food compartment are significantly
higher than in a conventional system,**
allowing fresh produce and other unsealed
foods to retain their moisture content and
freshness longer. Moisture sensitive foods
such as fresh fruit, salads, rice, etc., can now
be stored on open shelves without excessive
moisture loss.
™
(on some models) GEAppliances.com
Due to the higher humidity in the refrigerator,
you may on occasion experience fog or
small amounts of moisture in the refrigerator
compartment. This is normal and may
come and go as different food loads and
environmental conditions change. Wipe dry
with a paper towel if desired.
The separate airflow system minimizes the
mixing of air between the two compartments,
which reduces fresh food odor transfer to
improve the taste of ice.
The ClimateKeeper2™ system also reduces
the number of defrosting cycles in the freezer
evaporator, thereby reducing freezer burn.
* Freezer air is used in the CustomCool™
feature.
** Testing shows a higher level of humidity in
the Fresh Food section in ClimateKeeper2™
refrigerators versus conventional units.
About TurboCool.™ (on some models)
How it Works
TurboCool ™ rapidly cools the refrigerator
compartment in order to more quickly cool
foods. Use TurboCool ™ when adding a
large amount of food to the refrigerator
compartment, putting away foods after they
have been sitting out at room temperature or
when putting away warm leftovers. It can also
OR
be used if the refrigerator has been without
power for an extended period.
Once activated, the compressor will turn
on immediately and the fans will cycle on
and off at high speed as needed for eight
hours. The compressor will continue to run
until the refrigerator compartment cools to
approximately 34°F (1°C), then it will cycle
on and off to maintain this setting. After 8
hours, or if TurboCool ™ is pressed again, the
refrigerator compartment will return to the
original setting.
How to Use
Press TurboCool.™ The TurboCool ™
temperature display will show Tc and the
LED will be activated.
After TurboCool ™ is complete, the TurboCool
™ indicator light will go out.
NOTES: The refrigerator temperature cannot
be changed during TurboCool ™.
The freezer temperature is not affected
during TurboCool ™.
When opening the refrigerator door
during TurboCool ™, the fans will
continue to run if they have cycled on.
5
About ExpressChill™. (on some models)
How it Works
The ExpressChill™ feature is a system of
dampers, a fan and a temperature thermistor.
The pan is tightly sealed to prevent the pan’s
temperature from causing temperature
fluctuations in the rest of the refrigerator.
How to Use
Empty the pan. Place the Chill tray in the
pan. Place the items on the tray and close
the pan completely.
Select the ExpressChill™ pad. On some
models, you can then select the chill time
(use chart to determine best setting). Other
ExpressChill™
models will only have one option (45
minutes). On models with multiple settings,
tap the pad until the light appears next to
The controls for this pan are located in the top
of the refrigerator or on the dispenser with the
temperature controls.
the desired setting.
To stop a feature before it is finished, tap
that feature’s pad until no options are
selected and the display is off.
During ExpressChill™, the display on the
controls will count down the time in the
cycle.
How to Remove and Replace the Drawer
To remove:
Pull the drawer out to the stop position.
Rotate all four swing locks to the unlock
position.
Lift the front of the drawer up and out.
To replace:
Make sure all four swing locks are in the
unlock position.
Place the sides of the drawer into the
drawer supports, making sure the swing
locks fit on the drawer slots.
Lock all four swing locks by rotating them
to the lock position.
ExpressChill™ Chart (on some models)
NOTE: Results may vary depending on packaging, starting temperature and other food traits.
15 Minutes
1 Beverage Can (12 oz)
2 Small Juice Boxes
(6–8 oz each)
30 Minutes
2 to 6 Beverage Cans
(12 oz each)
2 Plastic 20 oz Bottles
of Beverage
4 to 6 Small Juice Boxes
(6–8 oz each)
3 Foil Juice Packets
Wine (750 ml bottle)
*HODWLQ³SDFNDJH
45 Minutes
2 Liters of Beverage
1/2 Gallon of Juice
6
About the water filter. (on some models) GEAppliances.com
Water Filter Cartridge
The water filter cartridge is located in the back upper right
corner of the refrigerator compartment.
When to Replace the Filter on Models With a
Replacement Indicator Light
There is a replacement indicator light for the water filter
cartridge on the dispenser. This light will turn orange to tell you
that you need to replace the filter soon.
The filter cartridge should be replaced when the replacement
indicator light turns red or if the flow of water to the dispenser or
icemaker decreases.
When to Replace the Filter on Models Without a
Replacement Indicator Light
The filter cartridge should be replaced every six months or
earlier if the flow of water to the water dispenser or icemaker
decreases.
Removing the Filter Cartridge
If you are replacing the cartridge, first remove the old one by
slowly turning it to the left. Do not pull down on the cartridge. A
small amount of water may drip down.
Installing the Filter Cartridge
If you are replacing a SmartWater cartridge with an
adapter, it must be removed before installing the cartridge.
To remove the adapter, turn it to the left about 1/4 turn.
If you are replacing a Water by Culligan cartridge, leave the
adapter in place. This adapter will stay in the refrigerator
when you replace future cartridges.
Some models
With adapter
(appearance may vary)
On models ithout a replacement indicator light, apply the
month and year sticker to the new cartridge to remind you
to replace the filter in six months.
Fill the replacement cartridge with water from the tap to
allow for better flow from the dispenser immediately after
installation.
Line up the arrow on the cartridge and the cartridge holder.
Place the top of the new cartridge up inside the holder. Do
not push it up into the holder.
Slowly turn it to the right until the
filter cartridge stops. DO
NOT OVERTIGHTEN. As you turn
the cartridge, it will automatically
raise itself into position. The
cartridge will move about 1/2
turn.
Without adapter
use this type of
water filter.
Cartridge
Holder
Run water from the dispenser 1-1/2 gallons (about three
minutes) to clear the system and prevent sputtering.
Press and hold the WATER FILTER pad (on some models) on
the dispenser for 3 seconds.
NOTE: A newly-installed water filter cartridge may cause water
to spurt from the dispenser upon first use.
Filter Bypass Plug
You must use the filter bypass plug when a replacement filter
cartridge is not available. The dispenser and the icemaker will
not operate without the filter or filter bypass plug.
Filter
Filter
Bypass
Plug
SmartWater
To use the filter bypass plug on Water by Culligan models, you
must first remove the filter adapter from the cartridge holder by
turning it to the left.
For the maximum benefit of your filtration system, GE
Appliances recommends the use of GE Appliances branded
SmartWater filters only. Using GE Appliances branded
filters in GE Appliances and Hotpoint refrigerators provides
optimal performance and reliability. GE Appliances branded
SmartWater filters are always the right choice because they are
patented and designed specifically for GE Appliances products.
SmartWater filters meet rigorous industry NSF standards for
safety and quality that are important for products that are
filtering your water. GE Appliances has not qualified non-GE
Appliances branded filters for use in GE Appliances and Hotpoint
refrigerators and there is no assurance that non-GE Appliances
branded filters meet GE Appliances standards for quality,
performance and reliability.
,I\RXKDYHTXHVWLRQV³YLVLWRXU:HEVLWHDWGEAppliances.com,
or call 1.800.GE.CARES (1.800.432.2737).
Replacement filters:
To order additional filter cartridges in the United States, visit our
Website at GEAppliances.com, or call GE Appliances Parts and
Accessories, 877.959.8688.
See filter label for type of filter to order (MWF or MSWF).
Customers in Canada should consult the yellow pages for the
nearest Mabe Service Center.
Bypass
Plug
Water by Culligan
7
About the shelves and bins.
Not all features are on all models.
Snugger
Refrigerator bin
Refrigerator Door Bins and Freezer Door Tilt-Out Bins
Large Bins
The larger refrigerator door bins and freezer
tilt-out door bins are adjustable.
To remove: Lift the front of the bin straight up,
then lift up and out.
To replace or relocate: Engage the back side of
the bin in the molded supports of the door. Then
push down on the front of the bin. Bin will lock
in place.
Small Bins
To remove: Lift the front of the bin straight up
then out.
The snugger helps prevent tipping, spilling or
sliding of small items stored on the door shelf.
Place a finger on either side of the snugger near
the rear and move it back and forth to fit your
needs.
Top freezer bin
NOTE:
Be careful when
placing items in
the top bin. Make
sure that items do
not block or fall
into the ice chute.
Freezer bin
Freezer tilt-out bin
Press tab and pull shelf
forward to remove
To replace: Position the bin above the
rectangular molded supports on the door. Then
slide the bin down onto the support to lock it in
place.
Slide-Out Spillproof Shelf
The slide-out spillproof shelf allows you to
reach items stored behind others. The special
edges are designed to help prevent spills from
dripping to lower shelves.
To replace or relocate:
Line the shelf up with the supports and slide it
into place. The shelf can be repositioned when
the door is at 90° or more. To reposition the
shelf, slide the shelf past the stops and angle
downward. Slide shelf down to the desired
To remove:
Slide the shelf out until it reaches the stop,
then press down on the tab and slide the shelf
straight out.
position, line up with the supports and slide into
place.
Make sure you push the shelves all the way
back in before you close the door.
Freezer Baskets (on some models)
To remove, slide out to the stop position, lift the
front past the stop position, and slide out.
Make sure you push the baskets all the way
back in before you close the door.
Freezer Baskets (on some models)
To remove, push the basket all the way to the
back of the freezer. Lift up until the back pins
are disengaged. Lift the entire basket up and
pull out.
Make sure you push the baskets all the way
back in before you close the door.
8
About the shelves and bins.
Not all features are on all models.
QuickSpace™ Shelf (on some models)
This shelf splits in half and slides under itself for
storage of tall items on the shelf below.
This shelf can be removed and replaced or
relocated just like Slide-Out Spillproof Shelves.
Slide-Out Freezer Shelves
To remove, slide out to the stop position, lift the
front past the stop position, and slide out from
rib.
Fixed Freezer Shelves
To remove, lift the shelf up at the left side and
then bring the shelf out.
Door Wine/Beverage Rack
(on some models)
This rack holds up to 5 cans, one bottle of
wine or one 2-liter bottle of soda.
The rack hangs from the sides of the dairy bin.
To remove:
Empty the wine/beverage rack.
GEAppliances.com
On some models, this shelf can not be used in
the lowest position.
Make sure you push the shelves all the way
back in before you close the door.
NOTE FOR DISPENSER MODELS: In order to
take full advantage of the tilt-out ice bin (on
some models), only store items on the shelf
below the ice bin that are no taller than the
lowest point on the bin.
Holding the bottom of the dairy bin, lift the
front straight up, then lift up and out.
To detach the rack from the dairy bin, pull
the rack’s side wires out of the holes on
each side of the dairy bin.
ShelfSaver™ Rack
(on some models)
Use this rack to store
beverage cans for easy
access.
It can also hold a 9” x 13”
baking dish.
Removable Beverage Rack
(on some models)
The beverage rack is designed to
hold a bottle on its side. It can be
attached to any slide-out shelf.
To replace:
Reattach the rack to the sides of the bin.
Engage the back side of the bin in the
molded supports on the door. Then push
down on the front of the bin. The bin will
lock into place.
Door Can Rack
(on some models)
This door rack holds up to 9 cans.
NOTE: This rack can only be
mounted in the top position under
the dairy bin.
1
2
To install:
Line up the large part of the
slots on the top of the rack with
the tabs under the shelf.
Then slide the rack back to lock
it in place.
9
About the refrigerator doors.
Refrigerator Doors
The refrigerator doors may feel different
than the ones you are used to. The special
door opening/closing feature makes sure
the doors close all the way and are securely
sealed.
When opening and closing the door you will
notice a stop position. If the door is opened
past this stop point, the door will remain
open to allow you to load and unload food
more easily. When the door is only partially
open, it will automatically close.
When the door is only partially
open, it will automatically close.
Beyond this stop the door will stay
open.
Door Alignment
If doors are uneven, adjust the refrigerator
door.
Using a 7/16” socket wrench, turn the
door adjusting screw to the right to raise
the door; to the left, to lower it. (A nylon
plug, imbedded in the threads of the pin,
prevents the pin from turning unless a
wrench is used.)
(on some models)
The resistance you feel at the stop position
will be reduced as the door is loaded with
food.
After one or two turns of the wrench,
open and close the refrigerator door
and check the alignment at the top of
the doors.
To remove the base
grille, open the doors,
remove the screw at
each end of the base
grille and then pull
the grille straight out.
10
7/16” Socket Wrench
Raise
About the crispers and pans. GEAppliances.com
Not all features are on all models.
Fruit and Vegetable Crispers
Excess water that may accumulate in the
bottom of the drawers should be wiped dry.
On some models, the bottom drawer has full
extension slides that allow full access to the
drawer.
HI
LO
Adjustable Humidity Crispers
Slide the control all the way to the HI setting to
provide high humidity recommended for most
vegetables.
D
L
O
C
C
O
L
D
E
S
T
Convertible Deli Pan (on some models)
The convertible deli pan has its own cold
air duct to allow a stream of cold air from
the freezer compartment or refrigerator
compartment to flow to the pan.
The variable temperature control regulates the
air flow from the Climate Keeper.
About crisper removal.
Not all features are on all models.
Crisper Removal
Crispers can easily be removed by pulling the
drawer straight out and lifting the drawer up
and over the stop location.
Slide the control all the way to the LO setting to
provide lower humidity levels recommended for
most fruits.
Set the control to the coldest setting to store
fresh meats.
Set the control to cold to convert the panto
normal refrigerator temperature and provide
extra vegetable storage space. The cold air
duct is turned off. Variable settings between
these extremes can be selected.
If the door prevents you from taking out the
drawers, first try to remove the door bins.
If this does not offer enough clearance, the
refrigerator will need to be rolled forward
until the door opens enough to slide the
drawers out. In some cases, when you roll the
refrigerator out, you will need to move the
refrigerator to the left or right as you roll it out.
11
About the automatic icemaker.
A newly installed refrigerator may take 12 to 24 hours to begin making ice.
Automatic Icemaker
7KHLFHPDNHUZLOOSURGXFHVHYHQFXEHVSHUF\FOH³
approximately 100–130 cubes in a 24-hour period, depending
on freezer compartment temperature, room temperature,
number of door openings and other use conditions.
If the refrigerator is operated before the water connection is
made to the icemaker, set the power switch in the OFF position.
When the refrigerator has been connected to the water supply,
set the power switch to the ON position.
The icemaker will fill with water when it cools to 15°F (–10°C).
A newly installed refrigerator may take 12 to 24 hours to begin
making ice cubes.
You will hear a buzzing sound each time the icemaker fills with
water.
Throw away the first few batches of ice to allow the water line
to clear.
Be sure nothing interferes with the sweep of the feeler arm.
When the bin fills to the level of the feeler arm, the icemaker will
stop producing ice. It is normal for several cubes to be joined
together.
If ice is not used frequently, old ice cubes will become cloudy,
taste stale and shrink.
CAUTION
the ejector mechanism, or with the heating element (located
on the bottom of the ice maker) that releases the cubes.
Do not place fingers or hands on the automatic ice making
mechanism while the refrigerator is plugged in.
Avoid contact with the moving parts of
Special note about dispenser models:
Some models have a tilt-out ice bin. The bin can be tilted
out as shown in the illustrations, and it will hold itself up
while you take ice out or turn the icemaker power switch on
and off. Be sure to put the bin back in place before closing
the door.
To restore your ice level from an empty bucket stage, the
following steps are recommended:
12 hours after the first batch of ice has fallen into the bin,
dispense 3 to 4 cubes.
After an additional 6 hours, dispense 3 to 4 cubes again.
These steps will restore your ice level in the shortest amount of
time.
Power
Switch
Green
Power Light
(on some models)
Icemaker
Feeler Arm
Power
Switch
(on some models)
Icemaker
Feeler Arm
NOTE:
In homes with lower than average water pressure,
you may hear the icemaker cycle multiple times
when making one batch of ice.
12
About the automatic icemaker. (cont) GEAppliances.com
Accessing Ice and Reaching the Power Switch on
Dispenser Models
There are two types of ice storage bins on dispenser models.
One has a shelf above the bin, the other does not.
Special note for models with tilt-out ice bin:
These models have a tilt-out ice bin. The bin can be tilted
out as shown in the illustrations, and it will hold itself up
while you take ice out or turn the icemaker power switch
on and off. Be sure to put the bin back in place before
closing the door.
NOTE: In order to take full advantage of the tilt-out ice bin, only store items
on the shelf below the ice bin that are no taller than the lowest point on the
bin.
Models with a shelf above the ice bin
Shelf
Ice Bin
To reach the power switch, pull the
shelf straight out. Always be sure to
To access ice, pull the bin forward.
replace the shelf.
Shelf
Ice Bin
Models with tilt out ice bin
To access ice and reach the icemaker power switch:
Lift the bin, then pull it forward
until the bin stops.
Removing Ice Bin
CAUTION
The ice bin is heavy when full.
(dispenser models)
Lower the bin to access ice or
reach the power switch.
Set the power switch to the OFF position before removing the
bin.
When replacing the bin, be sure to press it firmly into place. If
it does not go all the way back, remove it and rotate the drive
mechanism 1/4 turn. Then push the bin back again.
On some models, to access ice or reach the power switch:
Pull the bin forward until the
bin stops.
Rotate
Lower the bin to access ice or
reach the power switch.
Drive
Mechanism
Dispenser Models only
13
About the ice and water dispenser. (on some models)
To Use the Dispenser
Spill Shelf
Select CUBED ICE , CRUSHED ICE
or WATER .
Press the glass gently against the top of the
dispenser cradle.
The spill shelf is not self-draining. To reduce
water spotting, the shelf and its grille should be
cleaned regularly.
If no water is dispensed when the
refrigerator is first installed, there may be air
in the water line system. Press the dispenser
arm for at least two minutes to remove
trapped air from the water line and to fill the
water system. To flush out impurities in the
water line, throw away the first six glassfuls
of water.
CAUTION: Never put fingers or any other
objects into the ice crusher discharge
opening.
Locking the Dispenser
Press the LOCK pad for
3 seconds to lock the
dispenser and control
panel. To unlock, press and
hold the pad again for 3
seconds.
Dispenser Light
This pad turns the light in the
dispenser on and off. The
light also comes on when the
dispenser cradle is pressed.
For models with a bulb, if
the light burns out, it should
be replaced with a 6 watt
12V maximum bulb. For LED
models, contact Factory
Service.
Quick Ice (on some models)
When you need ice in a
hurry, press this pad to speed
up ice production. This will
increase ice production for
the following 48 hours or until
you press the pad again.
Door Alarm (on some
models)
To set the alarm, press this
pad until the indicator light
comes on. This alarm will
sound if either door is open
for more than 3 minutes.
The light goes out and the
beeping stops when you
close the door.
14
Important Facts About Your Dispenser
Do not add ice from trays or bags to the
storage drawer. It may not crush or dispense
well.
Avoid overfilling glass with ice and use of
narrow glasses. Backed-up ice can jam
the chute or cause the door in the chute to
freeze shut. If ice is blocking the chute, poke it
through with a wooden spoon.
Beverages and foods should not be quick-
chilled in the ice storage drawer. Cans,
bottles or food packages in the storage
drawer may cause the icemaker or auger to
jam.
To keep dispensed ice from missing the
glass, put the glass close to, but not touching,
the dispenser opening.
Some crushed ice may be dispensed
even though you selected CUBED ICE. This
happens occasionally when a few cubes
accidentally get directed to the crusher.
After crushed ice is dispensed, some water
may drip from the chute.
Sometimes a small mound of snow will form
on the door in the ice chute. This condition is
normal and usually occurs when you have
dispensed crushed ice repeatedly. The snow
will eventually evaporate.
Care and cleaning of the refrigerator. GEAppliances.com
Cleaning the Outside
Dispenser drip area.
The dispenser drip area, beneath the grille,
shou l d b e w i p e d dr y . W a t e r left in this area may
leave deposits. Remove the deposits by adding
undiluted vinegar to the well. Soak until the
deposits disappear or become loose enough to
rinse away.
The dispenser cradle. Before cleaning, lock the
dispenser by pressing and holding the LOCK
pad for 3 seconds. Clean with warm water and
EDNLQJVRGDVROXWLRQ³DERXWDWDEOHVSRRQ
ml) of baking soda to a quart (1 liter) of water.
Rinse thoroughly and wipe dry.
The door handles and trim. Clean with a cloth
dampened with soapy water. Dry with a soft
cloth.
Cleaning the Inside
To help prevent odors, leave an open box
of baking soda in the fresh food and freezer
compartments.
Unplug the refrigerator before cleaning. If
this is not practical, wring excess moisture
out of sponge or cloth when cleaning around
switches, lights or controls.
8VHZDUPZDWHUDQGEDNLQJVRGDVROXWLRQ³
about a tablespoon (15 ml) of baking soda to
a quart (1 liter) of water. This both cleans and
neutralizes odors. Rinse and wipe dry.
The stainless steel doors and door handles
(on some models) can be cleaned with a
commercially available stainless steel cleaner.
Cleaners with oxalic acid such as Bar Keepers
Friend Soft Cleanser™ will remove rust,
tarnish and small blemishes. Use only a liquid
cleanser free of grit and rub in the direction of
the brush lines with a damp soft sponge.
Do not use appliance wax or polish on the
stainless steel.
Keep the outside clean. Wipe with a clean cloth
lightly dampened with kitchen appliance wax or
mild liquid dish detergent. Dry and polish with a
clean, soft cloth.
Do not wipe the refrigerator with a soiled dish
cloth or wet towel. These may leave a residue
that can erode the paint. Do not use scouring
pads, powdered cleaners, bleach or cleaners
containing bleach because these products
can scratch and weaken the paint finish.
CAUTION
or covers with warm water when they are
cold. Glass shelves and covers may break
if exposed to sudden temperature changes
or impact such as bumping or dropping.
Tempered glass is designed to shatter into
many small pieces if it breaks.
Do not wash any plastic refrigerator parts in
the dishwasher.
The chill/thaw tray is dishwasher safe.
Do not clean glass shelves
Use of any cleaning solution other than that
which is recommended, especially those that
contain petroleum distillates, can crack or
damage the interior of the refrigerator.
15
Care and cleaning of the refrigerator. (cont.)
Behind the Refrigerator
Be careful when moving the refrigerator away
from the wall. All types of floor coverings can
be damaged, particularly cushioned coverings
and those with embossed surfaces.
Pull the refrigerator straight out and return it
to position by pushing it straight in. Moving the
refrigerator in a side direction may result in
damage to the floor covering or refrigerator.
Preparing for Vacation
For long vacations or absences, remove food
and unplug the refrigerator. Clean the interior
with a baking soda solution of one tablespoon
(15 ml) of baking soda to one quart (1 liter) of
water. Leave the doors open.
Set the icemaker power switch to the OFF
position and shut off the water supply to the
refrigerator.
Preparing to Move
Secure all loose items such as shelves and
drawers by taping them securely in place to
prevent damage.
When pushing the refrigerator back, make
sure you don’t roll over the power cord or
icemaker supply line (on some models).
If the temperature can drop below freezing,
have a qualified servicer drain the water supply
system (on some models) to prevent serious
property damage due to flooding.
Be sure the refrigerator stays in an upright
position during moving.
When using a hand truck to move the
refrigerator, do not rest the front or back of the
refrigerator against the hand truck. This could
damage the refrigerator. Handle only from the
sides of the refrigerator.
Replacing the light bulbs. (on some models)
WARNING
live wire filament. (A burned-out light bulb may break when being replaced.)
Turning the control to the OFF position does not remove power to the light circuit.
Your light shield will look like
one of the following:
Before replacing a burned-out light bulb, the refrigerator should be unplugged in order to avoid contact with a
5HIULJHUDWRU&RPSDUWPHQW³8SSHU/LJKW
Unplug the refrigerator.
The bulbs are located at the top of the
compartment, inside the light shield. On
Tabs
OR
Pocket
some models, a screw at the front of the
light shield will have to be removed. On
other models, the screw is located in the
pocket located at the back of the shield.
To remove the light shield, on some models,
press in on the tabs on the sides of the
shield and slide forward and out. On other
models, just slide the shield forward and
out.
After replacing the bulb with an appliance
bulb of the same or lower wattage, replace
the light shield and screw. When replacing
the light shield, make sure that the tabs at
the back of the shield fit into the slots at the
back of the light shield housing.
Plug the refrigerator back in.
16
Replacing the light bulbs. (cont) GEAppliances.com
WARNING
live wire filament. (A burned-out light bulb may break when being replaced.)
Turning the control to the OFF position does not remove power to the light circuit.
Before replacing a burned-out light bulb, the refrigerator should be unplugged in order to avoid contact with a
5HIULJHUDWRU&RPSDUWPHQW³/RZHU/LJKW
This light is located above the top drawer.
Unplug the refrigerator.
Lift the light shield up and pull it out.
Freezer Compartment
Unplug the refrigerator.
Remove the shelf just above the light shield.
(The shelf will be easier to remove if it is
emptied first.) Remove the screw at the top
of the light shield.
To remove the light shield, press in on the
sides, and lift up and out.
After replacing the bulb with an appliance
bulb of the same or lower wattage, replace
the shield.
Plug the refrigerator back in.
Replace the bulb with an appliance bulb
of the same or lower wattage, and
reinstall the light shield. When reinstalling
the light shield, make sure the top tabs
snap securely into place. Replace the
screw.
Reinstall the shelf and plug the
refrigerator back in.
Dispenser (on some models)
Unplug the refrigerator.
The bulb is located on the dispenser under
the control panel. Remove the light bulb by
turning it counterclockwise.
Replace the bulb with a bulb of the same
size and wattage.
Plug the refrigerator back in.
Replacing the lights on models with LED lighting
Setting the controls to OFF does not remove power to the light circuit. Not all features are on all models.
Refrigerator Compartment (on some models)
There is an LED lighting display in the top and sides of the fresh food compartment and in the rear
LED
Lighting
Display
and side of the freezer compartment on some models.
If this assembly needs to be replaced, call GE Appliances Service at 1.800.432.2737 in the United
States or 1.800.561.3344 in Canada.
17
Installation
Refrigerator
Instructions
Questions? Call 800.GE.CARES (800.432.2737) or Visit our Website at: GEAppliances.com
In Canada, call 1.800.561.3344 or Visit our Website at: www.geappliances.ca
Models 22, 23, 25, 26, 27 & 29
BEFORE YOU BEGIN
Read these instructions completely and carefully.
•
IMPORTANT ³6DYHWKHVHLQVWUXFWLRQVIRU
local inspector’s use.
•
IMPORTANT ³2EVHUYHDOOJRYHUQLQJ
codes and ordinances.
Note to Installer – Be sure to leave these
•
instructions with the Consumer.
• Note to Consumer – Keep these instructions for
future reference.
• Skill level – Installation of this appliance requires
basic mechanical skills.
• Completion time –
• Proper installation is the responsibility of the
installer.
• Product failure due to improper installation is not
covered under the Warranty.
If the refrigerator has already been installed, remove
the base grille (see Step 2 in Moving the Refrigerator),
then skip to Step 5 in Installing the Refrigerator.
Refrigerator Installation
30 minutes
Water Line Installation
30 minutes
PREPARATION
WATER SUPPLY TO THE ICEMAKER
If the refrigerator has an icemaker, it will have to
be connected to a cold water line. A GE Appliances
water supply kit (containing tubing, shutoff valve,
fittings and instructions) is available at extra
cost from your dealer, by visiting our Website at
GEAppliances.com (in Canada at www.geappliances.
ca) or from Parts and Accessories, 877.959.8688 (in
Canada 1.800.661.1616).
TOOLS YOU WILL NEED
3/8” and 5/16” Socket 1/2” and 7/16” Wrench
Plastic Putty Knife
18
Phillips Head Screwdriver
Installation Instructions
MOVING THE REFRIGERATOR
LOADING THE REFRIGERATOR
1
ONTO A HAND TRUCK
Leave all tape and door pads on doors until the
refrigerator is in its final location.
To move the refrigerator, use a padded hand
truck. Center the refrigerator on the hand truck
and secure the strap around the refrigerator.
DO NOT OVERTIGHTEN THE STRAP.
If the refrigerator must go through any
entrance that is less than 38” wide, the
doors must be removed. Proceed to
Step 3.
DO NOT remove the handles.
If all entrances are more than 38” wide,
skip to Installing the Refrigerator.
DISCONNECT THE WATER COUPLING
3
(on some models)
If the refrigerator has a water dispenser,
there is a water line from the cabinet into the
bottom hinge on the freezer door that must be
disconnected.
To disconnect, push in on the white collar of
the coupling and pull out the tubing.
White collar
REMOVE THE BASE GRILLE
2
Remove the grille by removing the two
Phillips head screws.
Bottom
freezer
hinge
19
Installation Instructions
MOVING THE REFRIGERATOR (CONT.)
DISCONNECT THE POWER COUPLING
4
(on some models)
If the refrigerator has a water dispenser,
there is a power line (harness) from the cabinet
into the bottom hinge on the freezer door that
must be disconnected.
To disconnect, pull apart at the coupling.
Bottom
freezer
hinge
DISCONNECT THE ELECTRICAL
5
CONNECTORS (on some models)
If the refrigerator has a refreshment center,
there are electrical connectors (harnesses)
from the cabinet into the bottom hinge on the
refrigerator door that must be disconnected.
To disconnect, pull apart each connector.
CLOSE THE FREEZER AND
6
REFRIGERATOR DOORS
REMOVE THE FREEZER DOOR
7
Remove the freezer door top hinge cover (if
A
equipped) by either squeezing it and pulling it
up or by prying it off with a plastic putty knife.
Remove the two 5/16” hex head screws, then
B
lift the hinge straight up to free the hinge pin.
5/16” Hex Head
Bottom
refrigerator
hinge
20
Open the freezer door to 90.°
C
90°
Installation Instructions
REMOVE THE FREEZER DOOR (cont.)
7
As one person slowly lifts the freezer door up
D
and off the bottom hinge, the second person
should carefully guide the water line and power
line (harness) through the bottom hinge.
90°
Set the door on a non-scratching surface with
E
the inside up.
8
REMOVE THE REFRIGERATOR DOOR
Remove the refrigerator door top hinge cover
A
(if equipped) by either squeezing it and pulling it
up or by prying it off with a plastic putty knife.
REMOVE THE REFRIGERATOR DOOR
8
(cont.)
Remove the two 5/16” hex head screws, then
B
lift the hinge straight up to free the hinge pin.
5/16” Hex Head
C
Open the refrigerator door to 90.°
90°
21
Installation Instructions
MOVING THE REFRIGERATOR (CONT.)
REMOVE THE REFRIGERATOR DOOR
8
(cont.)
Lift the refrigerator door up and off the bottom
D
hinge.
If the refrigerator has a refreshment center,
one person should slowly lift the door up and
off the bottom hinge and the second person
should carefully guide the electrical lines
(harnesses) through the bottom hinge.
90°
REPLACING THE DOORS
9
To replace the doors, simply reverse steps 3
through 8.
However, please note the following:
• When lowering the doors onto the bottom
hinges, make sure the second person
carefully guides the tube and harnesses
through the holes in the hinges.
• When connecting the water line, make sure
you insert the tubing all the way to the mark.
Refreshment Center Models only
Set the door on a non-scratching surface with
E
the inside up.
Mark
• Do not pinch the tubing and harnesses when
placing the doors on the bottom hinges.
• When connecting the power line and the
electrical lines (refreshment center models
only), be sure that the connectors are seated
together fully.
22
Installation Instructions
INSTALLING THE REFRIGERATOR
REFRIGERATOR LOCATION
• Do not install the refrigerator where the
temperature will go below 60°F (16°C) because
it will not run often enough to maintain proper
temperatures.
• Do not install the refrigerator where the
temperature will go above 100°F (37°C) because
it will not perform properly.
• Do not install the refrigerator in a location exposed
to water (rain, etc.) or direct sunlight.
• Install it on a floor strong enough to support it
fully loaded.
CLEARANCES
Allow the following clearances for ease of
installation, proper air circulation and plumbing
and electrical connections:
23‘/25‘ 23‘ (33” wide),
CustomStyle™ 25‘, 26‘, 27‘, 29‘
Sides 1/8” (4 mm) 1/8” (4 mm)
Top 1” (25 mm) 1” (25 mm)
Back 1/2” (13 mm) -1” (25 mm)
DIMENSIONS AND SPECIFICATIONS (for
23‘ CustomStyle
™
models)
701ø4” (178.4 cm)
36”
(91.4 cm)
24” (61 cm)
DIMENSIONS AND SPECIFICATIONS (for
25‘ CustomStyle
™
models)
DIMENSIONS AND SPECIFICATIONS
Electrical
25” (63.5 cm)
Countertop
24” (61 cm)
Cabinet
Water
3/4” (19 mm)
Airspace
(1/2” [13 mm] Gap
+ 1/4” [6 mm] Wall
Plates)
721ø4” (183.5 cm)*
36”
(91.4 cm)
24” (61 cm)
* 721/4” (183.5 cm) required for full adjustment
of mobility wheels. If cabinets installed above
refrigerator have doors that are flush to the
top of the opening for the refrigerator, then
an additional 1/8” may be required to provide
clearance for cabinet doors to open freely.
23
Installation Instructions
INSTALLING THE REFRIGERATOR (CONT.)
CONNECTING THE REFRIGERATOR TO
1
THE HOUSE WATER LINE
(icemaker and dispenser models)
A cold water supply is required for automatic
icemaker and dispenser operation. If there
is not a cold water supply, you will need to
provide one. See “Installing the Water Line”
section.
NOTES:
• Before making the connection to the
refrigerator, be sure the refrigerator power
cord is not plugged into the wall outlet.
• If your refrigerator does not have a water
filter, we recommend installing one if your
water supply has sand or particles that could
clog the screen of the refrigerator’s water
valve. Install it in the water line near the
refrigerator.
If using SmartConnect
Tubing Kit, you will need an additional tube
(WX08X10002) to connect the filter. Do not
cut plastic tube to install filter.
If you are using copper tubing, place a
A
compression nut and ferrule (sleeve) onto the
end of the tubing coming from the house cold
water supply.
If you are using the SmartConnect
nuts are already assembled to the tubing.
If you are using copper tubing, insert the end of
B
the tubing into the refrigerator connection, at
the back of the refrigerator, as far as possible.
While holding the tubing, tighten the fitting.
If you are using SmartConnect
insert the molded end of the tubing into the
refrigerator connection, at the back of the
refrigerator, and tighten the compression nut
until it is hand tight. Then tighten one additional
turn with a wrench. Overtightening may cause
leaks.
™
Refrigerator
™
tubing,
™
tubing, the
Fasten the tubing into the clamp provided to
C
hold it in position. You may need to pry open
the clamp.
Tubing Clamp
1/4”
Compression Nut
Ferrule
(sleeve)
Refrigerator
Connection
TURN ON THE WATER SUPPLY
2
Turn the water on at the shutoff valve (house
water supply) and check for any leaks.
PLUG IN THE REFRIGERATOR
3
Before plugging in the refrigerator, make sure
the icemaker power switch is set to the OFF
position.
SmartConnect™ Tubing
1/4” Tubing
Option 2
24
See the grounding information attached to the
power cord.
Installation Instructions
PUT THE REFRIGERATOR IN PLACE
4
Move the refrigerator to its final location.
LEVEL THE REFRIGERATOR (cont.)
5
To adjust the
rollers on 23
CustomStyle
‘/25‘
™
models:
LEVEL THE REFRIGERATOR
5
The refrigerator can be leveled by adjusting the
rollers located near the bottom hinges.
Rollers
Rollers have three purposes:
• Rollers adjust so the door closes easily when
opened about halfway. (Raise the front about
5/8” [16 mm] from the floor.)
• Rollers adjust so the refrigerator is firmly
positioned on the floor and does not wobble.
• Rollers allow you to move the refrigerator
away from the wall for cleaning.
To adjust the rollers on 23‘ (33” wide), 25‘, 26‘,
27‘ and 29‘ models:
• Turn the roller
adjusting screws
clockwise to raise
the refrigerator,
counterclockwise
to lower it. Use a
3/8” hex socket
or wrench, or an
adjustable wrench.
Raise
Turn the front roller
adjusting screws
clockwise to raise
the refrigerator,
counterclockwise to
lower it. Use a 3/8” hex
wrench with extension, or an adjustable wrench.
These models also have rear adjustable
rollers so you can align the refrigerator with
your kitchen cabinets. Use a 3/8” hex wrench
with extension to turn the screws for the rear
UROOHUV³clockwise to raise the refrigerator,
counterclockwise to lower it.
LEVEL THE DOORS
6
Adjust the refrigerator door to make the doors
A
even at the top.
To align:
B
Using a 7/16” wrench, turn the door adjusting
screw to the right to raise the door, to the left
to lower it.
NOTE:
A nylon plug, imbedded in the threads of the
pin, prevents the pin from turning unless a
wrench is used.
After one or two turns of the wrench, open
and close the refrigerator door and check the
alignment at the top of the doors.
Doors should be even at top
Roller adjusting screws
Roller adjusting screw
Raise
7/16” wrench
25
Installation Instructions
INSTALLING THE REFRIGERATOR (CONT.)
REPLACE THE BASE GRILLE
7
Replace the grille by installing the two Phillips
head screws.
START THE ICEMAKER
9
Set the icemaker power switch to the I (on)
position. The icemaker will not begin to operate
until it reaches its operating temperature of
15°F (–9°C) or below. It will then begin operation
automatically. It will take 2–3 days to fill the ice
bin.
Power
switch
Power
switch
SET THE CONTROLS
8
Set the controls to the recommended setting.
NOTE:
In lower water pressure conditions, the water
valve may turn on up to 3 times to deliver
enough water to the icemaker.
26
Installation Instructions
INSTALLING THE WATER LINE (ICEMAKER & DISPENSER MODELS)
BEFORE YOU BEGIN
Recommended copper water supply kits are WX8X2,
WX8X3 or WX8X4, depending on the amount of tubing
you need. Approved plastic water supply lines are
SmartConnect
WX08X10015 and WX08X10025).
When connecting your refrigerator to a Reverse
Osmosis Water System, the only approved installation
is with a GE Appliances RVKit. For other reverse
osmosis water systems, follow the manufacturer’s
recommendations.
If the water supply to the refrigerator is from
a Reverse Osmosis Water Filtration System
AND the refrigerator also has a water filter,
use the refrigerator’s filter bypass plug. Using
the refrigerator’s water filtration cartridge in
conjunction with the RO filter can result in hollow
ice cubes and slower water flow from the water
dispenser.
This water line installation is not warranted by
the refrigerator or icemaker manufacturer. Follow
these instructions carefully to minimize the risk of
expensive water damage.
™
Refrigerator Tubing (WX08X10006,
WHAT YOU WILL NEED
• Copper or SmartConnect™ Refrigerator Tubing kit,
1/4” outer diameter to connect the refrigerator
to the water supply. If using copper, be sure both
ends of the tubing are cut square.
To determine how much tubing you need: measure
the distance from the water valve on the back of the
refrigerator to the water supply pipe. Be sure there
is sufficient extra tubing to allow the refrigerator to
move out from the wall after installation.
™
SmartConnect
available in the following lengths:
Refrigerator Tubing Kits are
8’ (2.8 m) – WX08X10006
15’ (4.6 m) – WX08X10015
25’ (7.6 m) – WX08X10025
Water hammer (water banging in the pipes) in
house plumbing can cause damage to refrigerator
parts and lead to water leakage or flooding. Call a
qualified plumber to correct water hammer before
installing the water supply line to the refrigerator.
To prevent burns and product damage, do not hook
up the water line to the hot water line.
If you use your refrigerator before connecting the
water line, make sure the icemaker power switch is
in the OFF position.
Do not install the icemaker tubing in areas where
temperatures fall below freezing.
When using any electrical device (such as a power
drill) during installation, be sure the device is double
insulated or grounded in a manner to prevent the
hazard of electric shock, or is battery powered.
All installations must be in accordance with local
plumbing code requirements.
27
Installation Instructions
INSTALLING THE WATER LINE (CONT.)
Install the shutoff valve on the nearest frequently used
WHAT YOU WILL NEED (CONT.)
NOTE: The only GE Appliances approved plastic
tubing is that supplied in SmartConnect
Tubing kits. Do not use any other plastic water supply
line because the line is under pressure at all times.
Certain types of plastic will crack or rupture with age
and cause water damage to your home.
• A GE Appliances water supply kit (containing
tubing, shutoff valve and fittings listed below) is
available at extra cost from your dealer or from
Parts and Accessories, 877.959.8688 (in Canada
1.800.661.1616).
• A cold water supply. The water pressure must be
between 20 and 120 p.s.i. (1.4–8.1 bar).
™
Refrigerator
drinking water line.
1
SHUT OFF THE MAIN WATER SUPPLY
2
CHOOSE THE VALVE LOCATION
Choose a location for the valve that is easily
Turn on the nearest faucet long enough to clear
the line of water.
accessible. It is best to connect into the side of
a vertical water pipe. When it is necessary to
connect into a horizontal water pipe, make the
connection to the top or side, rather than at the
bottom, to avoid drawing off any sediment from
the water pipe.
• Power drill.
• 1/2” or adjustable wrench.
• Straight and Phillips blade screwdriver.
• Two 1/4” outer diameter compression nuts and 2
ferrules (sleeves)³WRFRQQHFWWKHFRSSHUWXELQJWR
the shutoff valve and the refrigerator water valve.
OR
• If you are using a SmartConnect
Tubing kit, the necessary fittings are preassembled
to the tubing.
• If your existing copper water line has a flared fitting
at the end, you will need an adapter (available
at plumbing supply stores) to connect the water
line to the refrigerator OR you can cut off the
flared fitting with a tube cutter and then use a
compression fitting. Do not cut formed end from
SmartConnect
™
Refrigerator tubing.
™
Refrigerator
DRILL THE HOLE FOR THE VALVE
3
Drill a 1/4” hole in the water pipe (even if using
a self-piercing valve), using a sharp bit. Remove
any burrs resulting from drilling the hole in the
pipe.
Take care not to allow water to drain into the
drill.
Failure to drill a 1/4” hole may result in reduced
ice production or smaller cubes.
• Shutoff valve to connect to the cold water line.
The shutoff valve should have a water inlet with a
minimum inside diameter of 5/32” at the point of
connection to the COLD WATER LINE. Saddle-type
shutoff valves are included in many water supply
kits. Before purchasing, make sure a saddle-type
valve complies with your local plumbing codes.
28
Installation Instructions
4
FASTEN THE SHUTOFF VALVE
Fasten the shutoff valve to the cold water pipe
with the pipe clamp.
Pipe Clamp
Saddle-Type
Shutoff Valve
NOTE: Commonwealth of Massachusetts
Vertical Cold Water Pipe
Plumbing Codes 248CMR shall be adhered to.
Saddle valves are illegal and use is not permitted
in Massachusetts. Consult with your licensed
plumber.
TIGHTEN THE PIPE CLAMP
5
Tighten the clamp screws until the sealing
washer begins to swell.
NOTE: Do not overtighten or you may crush the
tubing.
Washer
Pipe Clamp
Inlet End
7
CONNECT THE TUBING TO THE VALVE
Place the compression nut and ferrule (sleeve)
for copper tubing onto the end of the tubing and
connect it to the shutoff valve.
Make sure the tubing is fully inserted into the
valve. Tighten the compression nut securely.
For plastic tubing from a SmartConnect
™
Refrigerator Tubing kit, insert the molded end
of the tubing into the shutoff valve and tighten
compression nut until it is hand tight, then
tighten one additional turn with a wrench.
Overtightening may cause leaks.
Saddle-Type
Shutoff Valve
Packing Nut
Outlet Valve
Compression Nut
SmartConnect™ Tubing
Ferrule (sleeve)
NOTE: Commonwealth of Massachusetts
Plumbing Codes 248CMR shall be adhered to.
Saddle valves are illegal and use is not permitted
in Massachusetts. Consult with your licensed
plumber.
Clamp
Screw
ROUTE THE TUBING
6
Route the tubing between the cold water line
and the refrigerator.
Route the tubing through a hole drilled in the
wall or floor (behind the refrigerator or adjacent
base cabinet) as close to the wall as possible.
NOTE: Be sure there is sufficient extra tubing to
allow the refrigerator to move out from the wall
after installation.
8
FLUSH OUT THE TUBING
Turn the main water supply on and flush out the
tubing until the water is clear.
Shut the water off at the water valve after about
one quart (1 liter) of water has been flushed
through the tubing.
To complete the installation of the refrigerator, go back
to Step 1 in Installing the Refrigerator.
29
Normal operating sounds.
Newer refrigerators sound different from older refrigerators. Modern refrigerators have more features and
use newer technology.
Do you hear what I hear? These sounds are normal.
HUMMM...
WHOOSH...
The new high efficiency compressor may run faster
and longer than your old refrigerator and you may
hear a high-pitched hum or pulsating sound while it is
operating.
Sometimes the refrigerator runs for an extended period,
especially when the doors are opened frequently. This
means that the Frost Guard™ feature is working to
prevent freezer burn and improve food preservation.
You may hear a whooshing sound when the doors close.
This is due to pressure equalizing within the refrigerator.
You may hear
the fans spinning at high speeds. This happens when
the refrigerator is first plugged in, when the doors are
opened frequently or when a large amount of food is
added to the refrigerator or freezer compartments. The
fans are helping to maintain the correct temperatures.
If either door is open for over 3 minutes, you may hear
the fans come on in order to cool the light bulbs.
The fans change speeds in order to provide optimal
cooling and energy savings.
CLICKS, POPS,
CRACKS and CHIRPS
You may hear cracking or popping sounds when the
refrigerator is first plugged in. This happens as the
refrigerator cools to the correct temperature.
Electronic dampers click open and closed to provide
optimal cooling and energy savings.
The compressor may cause a clicking or chirping sound
when attempting to restart (this could take up to 5
minutes).
The electronic control board may cause a clicking
sound when relays activate to control refrigerator
components.
Expansion and contraction of cooling coils during and
after defrost can cause a cracking or popping sound.
On models with an icemaker, after an icemaking cycle,
you may hear the ice cubes dropping into the ice
bucket.
WATER SOUNDS
The flow of
refrigerant through the freezer cooling coils may make
a gurgling noise like boiling water.
Water dropping on the defrost heater can cause a
sizzling, popping or buzzing sound during the defrost
cycle.
A water dripping noise may occur during the defrost
cycle as ice melts from the evaporator and flows into
the drain pan.
Closing the door may cause a gurgling sound due to
pressure equalization.
For additional information on normal
icemaker and dispenser operating sounds,
see the About the automatic icemaker and
About the ice and water dispenser sections.
30
Loading...