Consumer SupportTroubleshooting TipsOperating InstructionsSafety Instructions
Options
The light above the selected pad will be ON to indicate which OPTION has been selected.
POWER For use with heavily soiled and/or dried-on, baked-on soils. This option
MUST
be selected
PRIOR
to starting the cycle.
PRESOAK
This option adds 16 minutes to the cycle time.
SPEED DRY/ Shuts off the drying heat option. Dishes air dry naturally and energy is saved. You can prop the door open after the
HEATED DRY
CLEAN
light illuminates.
OFF
SPEED DRY/ Turns the heater on for fast drying. This cycle will extend the time to your wash cycle by 23 minutes for the
NORMAL
HEATED DRY cycle and 30 minutes for the
SANI WASH
cycle.
NOTE:
Cannot be selected with
RINSE ONLY
cycle.
ON
LOCK
When the
LOCK
pad is touched twice within 3 seconds, all pads become inoperative.
You can lock the controls to prevent any selections from
being made. Or you can lock the controls after you have
started a cycle or selected DELAY START so the cycle or DELAY START is not interrupted.
Children cannot accidentally start dishwasher by touching pads with this option selected.
To unlock the dishwasher after it has been locked, touch the
LOCK
pad twice within 3 seconds. The light above the
LOCK
pad will turn off.
DELAY START You can delay the start of a wash cycle for up to 8 hours. Press the
DELAY START
pad to choose the number of hours you want
to delay
the start of the cycle. The machine will count down and start automatically
at the correct time. Pressing the
START/RESET
button will cancel the
DELAY START
selection.
NOTE:
If you forget to latch the door, a reminder signal will beep until you do so.
RESET To change a cycle after washing starts, touch the
START/RESET
pad to cancel the cycle. After water is pumped out and the
motor stops, you can reprogram and restart the dishwasher. This will take approximately 90 seconds.
Load Selections
The light above the selected pad will be ON to indicate which LOAD SELECTION has been selected
.
SANI WASH This cycle raises the water temperature in the final rinse to sanitize your dishware. The cycle length will vary depending
on the temperature of your inlet water.
NOTE:
The SaniWash cycle is monitored for sanitization requirements. If the cycle is interrupted during or after the main wash
portion or if the incoming water temperature is so low that adequate water heating cannot be achieved, the sanitizing conditions
will not be met. In these cases, the sanitized light will not illuminate at the end of the cycle.
POTS & PANS For heavily soiled dishes or cookware with dried-on or baked-on soils.
Everyday dishes may be included.
This cycle will not remove burned-on foods.
NORMAL
For loads of everyday dishes, glasses and cookware with medium soils.
NOTE:
Many dishes have lighter soil than normal.
Choosing
a cycle other than
NORMAL
will save energy and water.
SPEED WASH/ For dishes with light soils.
LIGHT WASH
CHINA CRYSTAL For lightly soiled china and crystal.
RINSE ONLY For rinsing partial loads that will be washed later.
Do not use detergent.
The Status
The Status display tells you what is happening while the dishwasher is in operation and also any malfunctions if they occur (see page 6). The lights
will come ON indicating the sequence of operation the dishwasher is in.
SENSING Displayed during periods using CleanSensor technology to measure the amount of soil in the load and decide if another prewash
is needed. The SENSING light is displayed only during NORMAL and POTS & PANS cycles.
WASHING Displayed during prewash and main wash periods.
RINSING Displayed during rinse periods.
DRYING Displayed during
SPEED DRYING/HEATED DRYING
.
SANITIZED Displayed when cycle has met sanitization conditions. Light remains ONuntil door is opened.
Start
Close and latch the door. Touch the
START/RESET
pad to begin the cycle. Water fill begins, and approximately 40 seconds
later the wash action begins.
NOTE:
The dishwasher remembers your last cycle so you don’t have to reprogram each time. When the dishwasher is loaded
and the door latch is in the locked position, the control panel lights will be
ON
and display the last settings you selected.
If you don’t want to change any of the settings, simply touch the
START/RESET
pad to begin the cycle.
Also, if a power failure occurs,
NORMAL
and
SPEED DRY/HEATED DRY
will automatically be programmed. Make any new
selections and touch the
START/RESET
pad to begin the cycle.
Control Settings
GEAppliances.com
Clean
This light is illuminated when a wash cycle is complete. The light will stay
ON
until the door is opened.
5