GE Appliances
GSD3200GWW/CC/BB—GE Nautilus™ Built-In Dishwasher
Built-In Dishwasher Dimensions |
Rough-In Installation Information |
(in inches) |
(in inches) |
25-3/4 |
24 |
|
MAX. |
|
|
|
|
|
23-3/8* |
|
|
|
24-3/4 |
Hot |
|
water |
|
|
|
line on |
34 MIN. |
|
left |
adj. to 35 |
|
|
21-1/2
90°
24"
MIN.
34-1/2±1/4" Underside 6
of countertop to floor
2
|
|
Countertop |
|
This wall area |
|
|
must be free of |
90° |
|
pipes or wires |
|
4 |
4 |
Electrical |
|
|
wiring is |
|
4 |
3" from |
5 |
5 |
cabinet |
|
||
|
|
Electrical |
|
6 |
wiring on |
|
|
right |
Plumbing and electrical service must enter inside shaded area
19" MIN. from wall |
24" From wall |
|
White (neutral) |
|
Ground |
|
Black (line) |
24" MIN.
3-1/4
4 (Adjustable)
Note: Dishwasher must not be installed more than 10 feet from |
|
sink for proper drainage. All plumbing and electrical work must |
|
be in accordance with local codes. |
|
Electrical Rating |
|
Voltage AC....................................................... |
120 |
Hertz .................................................................. |
60 |
Total connected load amperage....................... |
6.2 |
Calrod® heater watts....................................... |
500 |
For use on adequately wired 120-volt, 15-amp |
|
circuit having 2-wire service with a separate |
|
ground wire. This appliance must be grounded |
|
for safe operation. |
|
Specification Created 11/01
Wood Insert Cut-Out
Dimensions (in inches)
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Door insert |
|
|
|
|
|
A |
|
Panel Thicknes |
||||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
3/4 |
|
|
|||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Front |
|||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
of |
||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Panel |
|||||||||||
|
|
Access insert |
|
|
|
|
|
C |
||||||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
1-1/2 |
|
|
|
|
|
|
|
|
|||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
1/2 |
|
|
|
|
|||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
B |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
1/4 |
||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Panel |
|||||||
Models/Kits |
A |
|
|
B |
|
|
|
|
C |
|
Thickness |
|||||||||||||||
GE Models |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
||
GPF325 Kit |
18-7/8” |
|
23-9/16” |
|
|
3-11/16” |
|
|
|
|
|
1/4” |
||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
4-1/4” to |
|
|
|
|
|
|
|
|
|
|
|
||
GPF375 Kit |
18-15/16” |
|
23-5/8”* |
|
|
3-3/4”** |
|
|
|
|
|
3/4” |
*Bottom of panel must be notched 1-1/2" x 1/2" to clear across panel
**Adjustment required to match adjcent cabinets fronts due to leveling leg adjustment, 4" nominal.
For answers to your Monogram,® GE Profile™ or GE appliance questions, visit our website at GEAppliances.com or call
GE Answer Center® service, 800.626.2000.
Listed by
Underwriters
R Laboratories