GE GPS12FSHCSB, GPS12FGHCWW, GPS12FGHCBB, GPS12FGHBSB, GPS12FGHBBB Owner’s Manual

GEAppliances.com

Safety Instructions..............2,3

Operating Instructions

Control Settings ....................... 4

Storage Drawers ....................... 4

Ice Service .............................. 5

Care and Cleaning .................. 6, 7

Installation Instructions

Advanced Planning ................... 8

Refrigerator Features .................. 9

Reversing the Door Swing ........ 1O,11

GPS72FG GPS72FS

Congelateur superieur

Rdri urs

Troubleshooting Tips

Normal Operating Sounds ........... 12

Problem Solver ................... 13, 14

Consumer Support

Warranty ........................... 16

Consumer Support .......... Back Page

Lc_section frc_nqc#se commence 2_Ic_pc_ge 77

Congelador superior

Refg ad

Lc_seccion en e.sfoc_ho/empieze_ en Ic_pc)ginc_ 33

rl er ores

Write the model and serial

numbers here: Model// Serial #

You can find them on a label inside the refrigerator,

752B2658PO07 49-60707 04- 74 GE

IMPORTANT SAFETYINFORMATION. READALL INSTRUCTIONSBEFOREUSING.

IMPORTANT SAFETY INFORMATION READ ALL INSTRUCTIONS BEFORE USING

GEAppliances website

For more information on your refrigerator's operation, visit www, GEAppliances.com or call 800, GECARES (800, 432,2737), In Canada visit GEAppliances.ca or call 800, 567,3344,

REFRIGERATOR SAFETY INFORMATION

A This is the safety alert symbol, This symbol alerts you to potential hazards that can kill or hurt you and others, All safety

messages will follow the safety alert symbol and the word "DANGER", "WARNING", or "CAUTION", These words are defined as:

Indicates a hazardous situation which, if not avoided, will result in death or serious injury,

Indicates a hazardous situation which, if not avoided, could result in death or serious injury,

Indicates a hazardous situation which, if not avoided, could result in minor or moderate injury,

IMPORTANT SAFETY INSTRUCTIONS

To reduce the risk of fire, explosion, electric shock, or injury when using your

refrigerator follow these basic safety precautions:

This refrigerator must be properly installed and located in

accordance with the Installation Instructions before it is used,

Do not allow children to climb, stand or hang on the shelves in the refrigerator, They could damage the refrigerator and

seriously injure themselves, Do not touch the cold surfaces in the freezer compartment,

particularly when hands are damp or wet, Skin may stick to

these extremely cold surfaces,

Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance,

, In refrigerators with automatic ice makers, avoid contact

with the moving parts of the ejector mechanism, or with the heating element that releases the cubes, Do not place

fingers or hands on the automatic ice making mechanism while the refrigerator is plugged in,

Keep fingers out of the "pinch point" areas; clearances between the doors and between the doors and cabinet are

necessarily small, Be careful closing doors when children are in the area,

Unplug the refrigerator before cleaning and making repairs,

NOTE: We strongly recommend that any servicing be

performed by a qua/ified individual,

Turning the control to the COLD position does not remove

power to the light circuit, Do not refreeze frozen foods which have thawed

completely,

Before replacing a burned-out light bulb, the refrigerator shouldbe unpluggedin order to avoid contact with a live

wire filament, (A burned-out light bulb may break when

being replaced,)

IMPORTANT SAFETYINFORMATION. READALL INSTRUCTIONSBEFOREUSING.

GEAppliances. corn

_ Explosion Hazard.

Keep flammable materials and vapors, such as gasoline, away from refrigerator. Failure to do so can

result in fire, explosion, or death.

CONNECTING ELECTRICITY

Electrical Shock Hazard.

Plug into a grounded 3-prong outlet Do not remove the ground prong

IDonot use an adapter

lFailure to follow these instructions can result in death, fire, or electrical shock.

Do not, under any circumstances, cut or remove the third (ground) prong from the power cord. For personal safety, this appliance must be properly grounded.

The power cord of this appliance is equipped with a 3-prong (grounding) plug which mates with a standard 3-prong (grounding) wall outlet to minimize the possibility of electric shock hazard from this appliance,

Have the wall outlet and circuit checked by a qualified

electrician to make sure the outlet is properly grounded, Where a standard 2-prong wall outlet is encountered, it is

your personal responsibility and obligation to have it replaced with a properly grounded 3-prong wall outlet, Do not use an adapter,

The refrigerator should always be plugged into its own

individual electrical outlet which has a voltage rating that matches the rating plate,

This provides the best performance and also prevents overloading house wiring circuits which could cause a fire

hazard from overheated wires,

Never unplug your refrigerator by pulling on the power cord,

Always grip plug firmly and pull straight out from the outlet, Repair or replace immediately all power cords that have

become frayed or otherwise damaged, Do not use a cord that shows cracks or abrasion damage along its length or at

either end, When moving the refrigerator away from the wall, be careful

not to roll over or damage the power cord,

PROPERDISPOSAL OF YOUR OLD REFRIGERATOR

Suffocation and child entrapment hazard. Remove flesh-food and freezer doors from the refrigerator, prior to disposal. Failure to do so can result in child entrapment which can lead to death or brain damage.

IMPORTANT:

Child entrapment and suffocation are not problems of the past, Junked or abandoned refrigerators are still dangerous even if they will sit for '_ust a few days," If you are getting rid of your old refrigerator, please follow the

instructions below to help prevent accidents, Before You Throw Away Your Old Refrigerator or

Freezer:

Take offthe fresh food and freezer doors,

Leave the shelves in place so that children may not easily climb inside,

Refrigerants

All refrigeration products contain refrigerants, which

under federal law must be removed prior to product

disposal, If you are getting rid of an old refrigeration

product, check with the company handling the disposal

about what to do,

READANDFOLLOWTHISSAFETYINFORMAflON CAREFULLX SAVETHESEINSTRUCTIONS

About the control on the refrigerator.

There is a temperature control in the fresh food compartment as well as the freezer

compartment./nit/ally set the control to the recommended normal settings in the fresh food

and freezer compartments. Allow 24 hours for the temperature to stabilize.

Temp Control

Freezer Temp Control

Min is Cold Middle is Normal

Max is Coldest

Contro/ Settings

The fresh food control and the freezer control should be

adjusted one increment at a time, Allow 12 hours after each adjustment for the compartment to reach the temperature you

have set,

Temp Control

Fresh Food Temp Control

1 is Cold

4 is Normal

7 is Coldest

After each adjustment, check both the freezer and the fresh food compartments, Changing the fresh food control will affect

the temperature of the freezer compartment, Likewise, changing the freezer control can affect the temperature of the fresh food compartment,

Control settings will vary based on personal preferences, usage and operating conditions and may require more than one

adjustment, Factors that affect temperature include the amount of food in the fresh food and freezer compartments, frequency

of door opening, and temperature of food when placed in either compartment,

About the storage drawers.

Fruit and Vegetable Drawers

These storage drawers provide space to store fruits, vegetables and meats,

To remove and replace the drawers and the

cover above them, the door must be fully opened, In some installations, the refrigerator

may have to be moved away from the wall for

the door to be fully opened,

About ice service. GEAppliances.com

Ice Trays

To make ice, fill the ice tray with water and set it on a level surface in the freezer compartment,

Ice cubes will form in a few hours, To release ice cubes, turn the tray upside down,

hold it over a container and twist both ends,

Ice maker Accessory Kit

An ice maker accessory kit is available from your dealer, The IM-4D or IM-6D accessory

kit will work with your refrigerator, To order, go to GEApplianceparts,com or call

800,626,2002, In Canada call 800,661,1 616, NOTE: The step shelf in the freezer MUST be

placed in the lowest position when the ice maker is installed,

Water Supply Kits

Kits containing copper tubing, shutoff valve, fittings and instructions needed to connect the

ice maker to your cold water line are available at extra cost from your dealer or from Parts and

Accessories, In the U,S,,call 800,626,2002, In Canada, call 800,661,1616

For only one or two ice cubes, leave the tray right-side up, twist both ends slightly and

remove as many cubes as you want,

Wash icetrays in lukewarm water only- do notput them in an automatic dishwasher,

The water valve cover assembly that came with the Owner's Manual must be

installed when installing the optional ice maker kit, Please call 1-800-432-2737 and

order part WR13X20070 if the water valve cover assembly is missing, In Canada, call

800,561,3344,

Care and cleaning of the refrigerator.

Cleaning the Outside

Keep the outside clean. Wipe with a clean

cloth lightly dampened with mild liquid dish detergent, Dry with a clean, soft cloth,

Do not wipe the stainless steel door with a soiled dishcloth or wet towel, These may

leave a residue that can erode the finish, Do not use scouring pads; powdered cleaners,

bleach or cleaners containing bleach because these products can scratch and

weaken the finish, Use only a liquid cleanser

f/'ee of grit and rub in the direction of the brush lines,

Cleaning the Inside

Tohelp prevent odors, leave an open box

of baking soda in the fresh food and freezer compartments,

Unplug the refrigerator before cleaning.

If this is not practical, wring excess moisture out of sponge or cloth when cleaning around

switches, lights or controls, Use warm water and baking sod(] solution-

about a tablespoon (15 ml) of baking soda to a quart (1 liter) of water, This both cleans and

neutralizes odors, Rinse and wipe dry,

Other parts of the refrigerator-including door gaskets,fruit and vegetable drawers, and all

plastic parts--can be cleaned the sameway.

The stainless steel door and door handle can be cleaned with a commercially

available stainless steel cleaner, Cleaners with oxalic acid (e,g, Bar Keepers Friend

Soft Cleanser) will remove rust, lime, and other tarnish, Do not use appliance wax or

polish on the stainless steel, Protect thepaint finish. The finish on the

outside of the refrigerator is a high quality,

baked-on paint finish, With proper care, it

will stay new-looking and rust free for years, Apply a coat of kitchen/appliance wax when

the refrigerator is new, and then at least twice a year,

After cleaning the door gaskets, apply a thin layer of petroleum jelly to the door gaskets

at the hinge side, This helps keep the gaskets from sticking and bending out of shape, Do

not use cleansing powders or other abrasive cleaners,

Do not wash any plastic refi'igerator parts in the dishwasher,

Avoid cleaning cold glass shelves (on some

models) with hot water because the extreme temperature difference may cause them to

break, Handle glass shelves carefL/l_ Bumping

tempered glass can cause it to shatter,

Bulb

Replacing the Light Bulb

NOTE: Turn off the appliance or disconnect

the electricity at the main power supply before

removing the light bulb, Failure to do so could result in electric shock or personal injur_

0 Unplug the refrigerator, 0 Remove the shelves (if necessary),

GEAppliances.com

The bulb may be replaced with an incandescent appliance bulb 25W or

less, To replace with a new LED bulb, please call 800,GE,CARES (800,492,2737)

during normal business hours, In Canada, call 800,661,1616

0 The light bulb is located behind a light lens

in the ceiling of the refrigerator section, The light lens is snapped in, To remove the light

lens, use a flat head screw driver to push one of the tabs

Unscrew the LED light bulb and tilt the

bulb up 30 to 45 ° to remove it from the socket,

Preparing for Vacation

For long vacations or absences, remove food and unplug the refrigerator, Clean the interior

with a baking soda solution of one tablespoon (15 ml) of baking soda to one quart (1 liter) of

water, Leave the doors open,

Preparing to Move

Remove food and unplug the refrigerator, Secure all loose items such as shelves and

drawers by taping them securely in place to prevent damage,

Using a bulb rated higher than 25W/120V may damage the control housing and light

lens,

Replace the light lens,

Be sure the refrigerator stays in an upright position during moving,

Installation

,efrigerator

Instructions

Models GPS12

ff you have questions, call 1.800. GE.CARES or visit our Website at: GEAppliances.com In Canada, call 1.800.561.3344 or Visit our Website at: www.geapp/iances.ca

BEFOREYOU BEGIN

Read these instructions completely and carefully.

"IMPORTANT - Save these instructions for local

inspector's use,

.IMPORTANT- Observea,,governingcodes

and ordinances,

. Note to Installer - Be sure to leave these instructions

with the Consumer,

. Note to Consumer - Keep these instructions

for future reference,

. Skill level - Installation of this appliance requires basic

mechanical skills,

. Completion time - Refrigerator Installation

15 minutes Reversing the Door Swing

1 hour

. Proper installation isthe responsibility of the installer, . Product failure due to improper installation is not covered

under the Warranty,

UNPACKING YOUR REFRIGERATOR

. Remove tape and any labels (except for the rating label)

from your refrigerator, Tape or glue residue can also be removed by rubbing a small amount of liquid dish soap over the adhesive with your fingers, Wipe with warm

water and dry,

, Do not use sharp instruments, rubbing alcohol,

flammable fluids, or abrasive cleaners to remove tape or glue, These products can damage the surface of your

refrigerator,

, When moving the refrigerator, do not tilt the refrigerator

beyond 45 °from upright position,

LEVELING LEGS

Adjustable legs at the front corners of the refrigerator should be set so the refrigerator is firmly positioned

on the floor, and the front is raised just enough that the door closes easily when opened about halfway,

To adjust the leveling legs, turn the legs clockwise to raise the refrigerator, counterclockwise to lower it,

LOCATION REQUIREMENTS

. Do not install the refrigerator where the temperature will go

below 55°F (13°C) because it will not run often enough to maintain proper temperatures,

. Install it on a floor strong enough to support it fully loaded,

CLEARANCES

. Free-standing installation only, . If the refrigerator is being installed next to a wall, leave

sufficient space on the hinge side to allow the door to swing open enough to access the clear bins inthe refrigerator compartment,

. Do not install within 5" (13 cm) of the range, . Minimum Clearances:

Back - 3" from the wall

To raise [he refrigerator

POWER CORD

. Plug the refrigerator power cord into its own properly

grounded wall outlet with a voltage rating matching that on the refrigerator rating plate,

. Do not use an extension cord, . Read all safety precautions on pages 2 and 3,

REFRIGERATOR FEATURES

Freezer Shelf

Freezer Temp Control

Refrig, Lamp

Refrigerator Temp Control

Lamp

Refrig Shelves

Cris F

Installation Instructions

Clear Freezer

Bins

Clear Refrigerator Door Bins

Adjustable Feet

Installation Instructions

REVERSINGTHE DOOR SWING

IMPORTANT NOTES

When reversing the door swing:

. Read the instructions all the way through before starting, . Handle parts carefully to avoid scratching paint, . Set screws down by their related parts to avoid using

them in the wrong places, . Provide a non-scratching work surface for the doors, . It is recommended that 2 people perform this task,

IMPORTANT; Once you begin, do not move the cabinet until door-swing reversal is completed,

These instructions are for changing the hinges from the right side to the left side-if you ever want to change

the hinges back to the right side, follow these same instructions and reverse all references to left and right,

Unplug the refrigerator from its electrical outlet. Empty all door shelves.

TOOLS YOU WILL NEED

[] REMOVE THE FRESH FOOD DOOR

Tape the door shut with masking tape,

Remove the center hinge by removing the screws, Lift

up the hinge to remove it, NOTE: Some models have a washer between the center hinge and the top of the fresh food door, Be

careful not to lose them,

Remove the tape holding the door shut,

Lift the fresh food door up and off the bottom hinge,

Set the door outside-up on a non-scratching surface, NOTE: When removing the door, watch for washer(s)

between the bottom hinge and the bottom of the fresh food door that may stick to the door, Do not lose,

8 mm Socket driver

Masking tape

Phillips screwdriver

Putt}/knife or

thin-blade screwdriver

ET1REMOVE THE FREEZER DOOR

Remove the hinge cover, Unscrew and remove the top hinge,

Lift the freezer door up and away from the

appliance, Set the door on a non-

scratching surface with the outside up,

Do not let door drop to the floor,

Doing so could damage the door stop,

Do not let door drop to the floor,

Doing so could damage the door stop,

F3qBOTTOM HINGE

Remove the screws and bottom hinge from the right

side, Remove the screw covers from the left corner,

Using the left hinge included with the parts that came

with your refrigerator along with the screws (and washers if applicable) removed earlier, install the left

hinge onto the bottom left of your refrigerator,

Place the screw covers into the holes now vacant on

the right,

Installation Instructions

REVERSINGTHE DOOR SWING (CONT.)

[] TRANSFER FRESH FOOD DOOR STOP

TO THE LEFT

Remove the door stop from the bottom of the right side of the door, Transfer the screw covers from the

bottom left side to the right side, Using the left door stop included with the parts that

came with your refrigerator, install the left door stop,

[] REHANG THE FRESH FOOD DOOR

Make sure the washer(s) are in place on the bottom hinge pin, Make sure the door is aligned horizontally

and vertically, Place the fresh food door on the bottom hinge, close the door and tape it in place with masking tape, / /"

[][] INSTALL CENTER HINGE ON

THE LEFT (CONT.)

ATTENTION: The screws must be

properly tightened. Turn the screws until

snug, Then tighten the screws a minimum of

1/2 turn using both

hands,

[]

TRANSFERTOP HINGE TO THE LEFT

Using a putty knife with the edge covered with masking tape, remove the screw cover on the left,

Be careful of the paint finish,

Reinstall the screw

cover on the right side,

TRANSFER FREEZER DOOR STOP TO THE LEFT

Remove the screw covers from the left edge of the door and insert it into the hole on the opposite side,

Screw Covers

r-eqINSTALL CENTER HINGE ON THE LEFT

Remove the three screw covers on the left side and install two of them on the right, Using the middle hinge and screws (and washers if

applicable) removed earlier, install the left middle hinge on the left side,

Remove the tape holding the door

shut,

assembled correctly, the

hinge is tight against the cabinet,

the bottom of the right side of ___:-- ........ --_

the door, Transfer the screw __ covers from the bottom left 0 1

side to the right side, Using the left door stop g

included with the parts that came with your refrigerator, install the left door stop,

[]_ REHANG THE FREEZER DOOR

Transfer the Screw Cover screw cover on top of the door to

the opposite side, Place the freezer [ ° door on the center hinge over the pin, Assure the door

is aligned horizontally and vertically, and that the gasket seals on all sides,

Attach the top hinge removed earlier on the left side of

your refrigerator and replace the hinge cover

Normal operating sounds.

Newer refrigerators sound different from older refrigerators. Modern refrigerators have more features and use newer technology.

Do you hear what I hear? These sounds are normal

HUMMM...

--WHOOSH...

The new high efficiency compressor may run faster and longer than your old refrigerator and you may hear a

high-pitched hum or pulsating sound while it is operating.

, You may hear a whooshing sound when the doors close.

This is due to pressure equalizing within the refrigerator.

CLICKS,POPS,

CRACKSand CHIRPS

, You may hear cracking or popping sounds when

the refrigerator is first plugged in. This happens , as the refrigerator cools to the correct temperature.

, The compressor may cause a clicking or chirping sound ,

when attempting to restart (this could take up to 5 minutes).

, Expansion and contraction of cooling coils during and ,

after defrost can cause a cracking or popping sound.

, On models with an ice maker, after an ice making

cycle, you may hear the ice cubes dropping into the ice , bucket.

WHIR./

, You may hear the fans spinning at high speeds.

This happens when the refrigerator is first plugged in, when the doors are opened frequently or when a large

amount of food is added to the refrigerator or freezer compartments. The fans are helping to maintain

the correct temperatures.

WATERSOUNDS

The flow of refrigerant through the freezer cooling coils may make a gurgling noise like boiling water.

Water dropping on the defrost heater can cause a sizzling, popping or buzzing sound during the defrost

cycle. A water dripping noise may occur during the defrost

cycle as ice melts from the evaporator and flows into the drain pan.

Closing the door may cause a gurgling sound due to pressure equalization.

Before you call for service... GEAppliances.com

Troubleshooting Tips Save time and money,/Review the charts on the following pages first and you may not need to call for service.

Possible Causes

Refrigeratordoesnot Refrigeratordefrostcycle.

, Refrigerator is unplugged.

The fuse is blown/circuit breaker is tripped.

Vibration or rattling Front leveling legs need adjusting. (slight vibration is normal)

Motoroperatesforlong Normalwhenrefrigeratorisfirstplugged

periods or cycles on and in.

off frequently. (Modern refrigerators with more food are placed in refrigerator.

storage space and a larger freezer require Door left open. Check to see if a package is holding door open,

more operating time, Hot weather or frequent door openings. This is normal,

Theystart andstop Temperature control set at the coldest See About the control, often to maintain even setting.

temperatures.) Fresh foodor freezer Temperature control not set cold See About the control,

compartment too warm enough.

Frost or ice crystals on Door left open. Check to see ira package is holding door open, frozen food (frost within Too frequent or too long door openings.

package is normal)

Ice cubes have odor/

Slow ice cube freezing

Refrigerator has odor

Moisture forms on outside of refrigerator Moisture collects inside (in humid weather, air

carries moisture into refrigerator when doors

are opened)

Often occurs when large amounts of This is normal,

Warm weather or frequent door Set the temperature control one step colder, See openings. About the control,

Door left open. Check to see if a package is holding door open,

Food transmitting odor/taste to ice Wrap foods well, cubes.

Interior of refrigerator needs cleaning. See Care and cleaning, Door left open. Check to see if package is holding door open, Temperature control not set cold See About the control,

enough. Foods transmitting odor to refrigerator. Foods with strong odors should be tightly wrapped,

Interior needs cleaning. See Cnre and cleaning, Not unusual during periods of high Wipe surface dry,

humidity. Too frequent or too long door openings.

What To Do

Wait about 30 minutes for defrost cycle to end,

Push the plug completely into the outlet, Replace fuse or reset the breaker,

See Leveling Legs,

Wait 24 hours for the refrigerator to completely cool down,

Keep an open box of baking soda in the refrigerator; replace every three months,

Before you carl for service...

Troubleshooting Tips Save time and money,/Review the charts on the following pages first and you may not need to call for service.

Interior light does not work

Food is freezing in the refrigerator

Rust, tarnish, or grime on

stainless steel doors

Possible Causes

No power at outlet, Light bulb burned out.

Food too close to the air vent at the back of the refrigerator.

Refrigerator control is set too cold.

Moist environment or salt air.

What To Do

Replace fuse or reset the breaker. See RepA?cingthe light bulb,

Move the food away from the air vent.

Move the refrigerator control to a warmer temperature setting one increment at a time. See

About the controls:

Clean stainless steel with cleaners containing oxalic acid (e.g. Bar Keepers Friend Soft

Cleanser) will remove rust, lime,and other tarnish. Do not wipe the refrigerator with a

soiled dish cloth or wet towel. Do not use scouring pads, powdered cleaners, bleach or

cleaners containing bleach because these products cGn scrGtch Gnd ruin the brush finish

of the stainless steel.

Notes. GEAppliances.com

Refrigerator Warranty.

For US Customers, all warranty service provided by our Factory Service Centers, or an authorized Customer Care '_technician. To schedule

service, on-line, 24 hours a day, visit us at OEAppliances.com, or call

800.GE.CARES (800.432.2737). Please have serial number and model number a vailable when calling for service.

In Canada, ca//800. 561.3344.

Servicing your refrigerator may require the use of the onboard data port for diagnostics. This gives a GE

Factory Service technician the ability to quickly diagnose any issues with your appliance and helps GE ,improve its products by providing GE with information on your appliance. If you do not want your appliance data to be

sent to GE, please advise your technician NOT to submit the data to GEat the time of service.

GE Will Replace

One Year Anypartofthe refrigerator which fails due to adefect in materials or workmanship. From thedate ofthe original Duringthe limited one-year warranty, GEwill also provide,freeofcharge, all labor and related service purchase to replacethe defective part.

Service trips to your home to teach you how to use the product.

Improper installation, delivery or maintenance. Failure of the product if it isabused, misused, or used for other

than the intended purpose or used commercially.

Lossof food due to spoilage. Replacement of house fuses or resetting of circuit breakers.

Damage caused after delivery. Replacement of the water filter cartridge, if included, due to water

pressure that is outside the specified operating range or due to

excessive sediment in the water supply.

Replacement of the light bulbs, if included, or water filter cartridge, if included, other than as noted above.

Damage to the product caused by accident, fire, floods or acts of God.

Incidental or consequential damage caused by possible defects

with this appliance. Product not accessible to provide required service. Damage to finish (rust, tarnish, or small blemishes) must be

reported within 48 hours following delivery of appliance.

Products which are not defective, broken, or which are working as

described in the owner's manual.

EXCLUSION OF IMPLIED WARRANTIES--Your sole and exclusive remedy is product repair as provided in this Limited Warranty. Any implied warranties, including the ,implied warranties of merchantability or fitness for a particular purpose, are limited to one year or the shortest period allowed by law

For US Customers: This warranty is extended to the original purchaser and any succeeding owner for products purchased for home use within the USA. If the product is located in an area where service by a GE Authorized Servicer is not available, you may be responsible for a trip charge or you may be required to bring the product to an Authorized GE Service location for service. In Alaska, the warranty excludes the cost of shipping or service calls to your home.

Some states do not allow the exclusion or limitation of incidental or consequential damages. This warranty gives you specific legal rights, and you may also have other rights which vary from state to state. To know what your legal rights are, consult your local or state consumer affairs office or your state's Attorney General.

Wa rra ntor US: General Electric Company. Louisvifle, KY 40225

For Customers in Canada: This warranty is extended to the original purchaser and any succeeding owner for products purchased in Canada for home use within Canada. In-home warrant service will be provided in areas where it is available and deemed reasonable by Mabe to provide.

Warrantor Canada: MC Commercial, Burlington, Ontario, LTt?5B6

+ 36 hidden pages