GE GLC5604V00BB, GLC5604V00WW, GLD2800V00WW, GLD2850V00CS, GLD4500V00BB Installation Guide

...

_ _ ° r¸_i _L_+° _._-._

_ #_'J_'_c__ _ _]I/ /II_]

Appliances

Installation Instructions

Built-In Dishwasher

If you have questions, call 800.GE.CARES{800.432.2737) or visit our Website at: GEAppliances.com. In Canada, please call 1.800.561.3344or visit www.geappliances.ca

BEFOREYOU BEGIN

Read these instructions completely and carefully.

IM PORTANT - Observe allgoverningcodes and

ordinances.

• Note to Installer - Be sure to leave these instructions for the consumer's and local inspector's use.

• Note to Consumer - Keep these instructions with your Owner's Manual for future reference.

• Skill Level - Installation of this dishwasher requires basic mechanical, electrical and plumbing skills. Proper installation is the responsibility of the installer. Product failure due to improper installation is not covered under the GE Appliance Warranty. See warranty information.

• Completion Time - i to 3 Hours. New installations require more time than replacement installations.

READ CAREFULLY. KEEP THESE INSTRUCTIONS.

IM PORTANT - The dishwasher MUST be installed

toallowforfutureremoval from the enclosureifserviceis

required.

If you received a damaged dishwasher, you should immediately contact your dealer or builder.

Optional Accessories - Seethe Owner's Manual for available custom panel kits.

FOR YOUR SAFETY

Read and observe all CAUTIONSand WARNINGS shown

throughout these instructions. While performing

installations described in this booklet, gloves, safety glasses or goggles should be worn.

31-30283 05-11GE

Installation Preparation

PARTS SUPPLIED IN INSTALLATION PACKAGE:

[] Two #8-18 x 5/8" Phillipsspecial head screws, to

secure dishwasher to underside of countertop

[] Junction box cover and #10 hex-head screw [] Hose clamp

[] Drain hose (approximately 78" long) [] Drain hose hanger [] Side and top trim pieces (some models) [] Literature, samples and/or coupons [] 2 Top-mounting brackets for wood countertops [] 2 Side-mounting brackets (on some models) for

non-wood countertops

[] Four#8 Phillips 3/8" pan-head screws

MATERIALS YOU WILL NEED:

[] Ferrule, compression nut and 90° elbow (3/8"NPT

external thread on one end, opposite end sized to fit water supply)

[] Thread seal tape [] UL-listed wire nuts (:3)

[] GPF65Side-Mounting Kit if countertop is

granite or similar material

Drain Hose

HoseClamp

Screw Kit

#8 Phillips #10 Special Hex-Head HeadScrews J-BoxScrew

5/8" long 112"long

90° Elbow, Hand

Ferrule and Shut-Off Thread

Compression Nut Valve Seal Tape

Side and Top Trim Pieces Ion some models)

Drain Hose Hanger

Mounting Kit

#8 Phillips 3/8"

Pan-head Top-Mounting

Screws Side-mounting Brackets

brackets (on some models)

Wire Nuts (3)

Junction

Box Cover

Materials Needed for

New Installations:

[] Air gap for drain hose, if required [] Waste tee for house plumbing, if applicable [] Electrical cable or power cord [] Screw-type hose clumps

[] Strain relief for electrical connection [] Hand shut-off valve (recommended)

[] Water line-3/8" minimum copper tubing [] GPF10Ldrain hose (10' long),if needed

TOOLS YOU WILL NEED:

[] Phillips-head screwdriver [] 1/4" and 5/16" nutdriver

[] 6" Adjustable wrench [] Level

[] Carpenter's square [] Measuring tape [] Safety glasses [] Flashlight [] Bucket to catch water when flushing the line [] 15/16" socket (optional for skid removal)

[] Gloves

Air Gap

Phill_

Screwdriver

15/16" Socket

Waste Tee

GPF65 Hose Clamps

Side-Mounting

Kit

Nutdriver

Electrical Cable (or Power Cord, if applicable)

Hot Water Line

Strain Relief

Optional

10' Drain Hose

GPFIOL

Level

Carpenter's

Square

Tubing Cutter

Measuring Tape

For New Installations Onlg:

[] Tubing cutter [] Drill and appropriate bits

[] Hole saw set

Gloves

Flashlight

Bucket

SafetyGlasses

Hole Saw Set

Installation Preparation

PREPARE DISHWASHER ENCLOSURE

AWARNING:

Toreducethe riskofelectric shock,fire,or injury to persons,the installermustensurethat the dishwasheriscompletelyenclosedat

thetime of installation.

ThisWallArea must beFree

of Pipesor wires

Cabinets

.Square

and Plumb

i 241,

Min.

Figure A

s4-1/2"_+1/4" Undersideof

Countertop

to Floor

With RoomFloor

MUSTbeEven

• The rough cabinet opening must be at least 24"deep, 24" wide and approximately 34-1/2" high from floor to underside of the countertop.

DRAIN REQUIREMENTS

• Follow local codes and ordinances.

• Do not exceed 10' distance to drain.

ADVERTENCIA:

Pororeducirel riesgode descorgoel6ctrico,incendioolesioneso personas,elinstolodordebeosegurorsedeque el Iovoplotosest6 completomentecerrodo enelmomenta deIoinstoloci6n.

• The dishwasher must be installed so that drain hose is no more than 10' in length for proper drainage.

• The dishwasher must be fully enclosed on the top, sides and back, and must not support any part of the enclosure.

CLEARANCES:When installed into a corner,

allow 2" min. clearance between dishwasher

and adjacent cabinet, wall or other appliances. Allow 28-3/8" min. clear- once from the front of

the dishwasher for door opening. Figure B.

Figure B

___ r_

Countertop

__ _I-3/8"

/ Clearance for Door

Opening2"Minimum

NOTE:Air gap must be used, if waste tee or disposer

connection is less than 18" above floor to prevent siphoning.

DETERMINE DRAIN METHOD

The type of drain installation depends on the following

questions. [] Dolocal codes or ordinances require an air gap? [] Iswaste tee lessthan Z8" above floor?

If the answer to either question is YES,Method 1MUST be used.

• If the answers are NO,either method may be used.

CABINET PREPARATION

• Drill a l-l/2" diameter hole in the cabinet wall within the shaded areas shown in Figure A for the drain hose connection. The hole should be smooth with no sharp edges.

IMPORTANT --When

connecting drain line to disposer, check to be sure that drain plug has

been removed. DISHWASHERWILL NOTDRAINIF PLUGISLEFTIN PLACE.

Drain

Plug

4 Remove

Figure C

Method 1 - Air Gap with Waste Tee or Disposer

Anair gapmust beusedwhen requiredbylocal codesandordi- nances.Theair gapmust beinstalledaccordingto manufacturer's

instructions.

__ DrainHoleo

Method 2 - "High Drain Loop" with Waste Tee or Disposer

Hanger

32"

_ _ DrainHoseHanger

Figure D

Tip: Avoid unnecessarg service call charges.

Always be sure disposer drain plug has been removed before attaching dishwasher drain hose to the disposer.

Installation Preparation

PREPARE ELECTRICAL WIRING

IkWARNING:

FOR PERSONAL SAFETY: Remove house fuse or open circuit breaker

beforebeginninginstallation.Do not usean extensioncord or

adapter plugwith thisappliance.

Ik ADVERTENCIA:

PARASEGURIDADPERSONAL:Quiteelfusible o abrael interruptor decircuitosantes decomenzarla instalaci6n.Noutilice uncable

deextensi6no un enchufeadaptadorconesteartefacto.

Electrical Requirements

• This appliance must be supplied with Z20V,60 Hz.,and

connected to on individual properly grounded branch circuit, protected by o Z5- or 20-ampere circuit breaker or time-delay

fuse.

• Wiring must be 2 wire with ground and rated for 75°C (176°F).

• If the electrical supply does not meet the above requirements,

coil o licensed electrician before proceeding.

Grounding Instructions-Permanent Connection This appliance must be connected to o grounded metal,

permanent wiring system, or on equipment-grounding

conductor must be run with the circuit conductors and be connected to the equipment-grounding terminal or lead on

the appliance.

Grounding Instructions-Power Cord Models This appliance must be grounded. In the event of o malfunction or breakdown, grounding will reduce the risk of electric shock

by providing o path of least resistance for electric current. This appliance is equipped with u cord having on equipment- grounding conductor and o grounding plug. The plug must

be plugged into an appropriate outlet that is installed and grounded in accordance with oil local codes and ordinances.

AWARNING:

Theimproper connectionof theequipmentgroundingconductor can resultin ariskof electricshock.Checkwith a qualified

electricianor servicerepresentativeifyou are indoubt that the applianceis properlygrounded.

/ t Receptacle

/'i Alternate

t Location

Figure E White

For models equipped with power cord: Do not modify the plug provided with the appliance; if it will not fit the outlet, have o proper outlet installed by o qualified technician.

Cabinet Preparation &Wire Routing

• Thewiring may enter the opening from either side, rear or the floor within the shaded area illustrated above in Figure Eand defined in Figure A.

• Cut o Z-l/2" maximum diameter hole to admit the electrical cable. Permanent wiring connections may pass through the

same hole as the drain hose and hot water line, if convenient. If cabinet wall is metal, the hole edge must be covered with o

bushing. NOTE:Power cords with plug must pass through oseparate

hole.

Electrical Connection to Dishwasher Electrical connection is on the right front of dishwasher.

• For permanent connections the cable must be routed us shown in Figure E.Cable must extend o minimum of 24" from

the rear wall.

• For power cord connections, install o 3-prong grounding type receptacle in the sink cabinet rear wall, 6" min. or Z8" maximum from the opening, 6" to Z8" above the floor.

I \ I \

Cabinet

ADVERTENCIA:

Laconexi6ninadecuadadelconductordeconexi6natierradel equipamientopuedeprovocarunriesgodedescargael6ctrica.

Consultea unelectricistacalificadoo representantedeservicio

t@cnicositienedudassabrelacorrectaconexi6na tierradelaparato.

Installation Preparation

PREPARE HOT WATER LINE

• The line may enter from either side, rear or floor within the shaded area shown in Figure F.

• The line may pass through the same hole as the electrical cable and drain hose. Or,cut an additional i-i/2" diameter

hole to accommodate the water line. If power cord with plug is used, water line must not pass through power cord hole.

ii Shut-off ,

Hot

From

Cabinet

FigureF

2" From Floor

Water Line Connection

•Turn off the water supply.

• Install a hand shut-off valve in an accessible location, such as under the sink. (Optional, but strongly recommended and may be required by local codes.)

• Water connection ison the left side of the dishwasher. Install

the hot water inlet line, using no less than 3/8" copper tubing.

Route the line as shown in Figure F and extend forward at least 19" from rear wall.

• Adjust water heater for 120°F to 150°F temperature.

• Flush water line to clean out debris.

• The hot water supply line pressure must be 20-120 PSI.

Turn page to begin dishwasher installation.

+ 11 hidden pages