GE GE Monogram ZICS360N RH, Monogram ZIC360NRH, Monogram ZICS360NRH, Monogram ZICS360NLH Design Manual

Installation Instructions

ZIC360NRH,ZIC360NLH, ZICS360NRH,ZICS360NLH

Built-In Bottom-Freezer Refrigerators

Design 6uide

With Installation Instructions

Monogram:

Safety Information

BEFORE YOU BEGIN

Read these instructions completely and carefully.

•IMPORTANT - heseinstructions

for h)cal inspector's use. Obserxe all goxerning codes and ordinances.

• Note to Installer -- Be sure to leaxe these

instructions with the (:onsmner.

• Note to Consumer -- Kee I) these instructions

with your Owner s Manual for flmue reference.

WARNING:

This appliance must be properly grounded. See "(;tom, cling tile Refrigerator," page 9.

AVERTISSEMENT

Cet appareil (hilt &tre correctement mis _'lla terre. Consulter <_ Mise _'lla terre du r(_frig_ratem" _>,I)age, 9.

If you receixed a damaged refrigerator, you should immediatelx contact xom" dealer or builder.

CAUTION:

Due to tile weight and size of this refrigerator, and to reduce tile risk of personal ii_jur) or damage to tile product--THREE PEOPI,E ARE REQUIRED

FOR PROPER ]NSTAI,I,ATION.

PRUDENCE

_ cause du poids et de la taille de ce r_frig&'ator et pore" r&luire le risque de blessure et de dommages,

li, E&UT TROIS PERSONNES POUR EMILE I,'INSTAI,LATION CORRECTEMENT.

Skill Level -- Installation of this refrigerator

requires basic mechanical, carpent_ T and plmnl)ing skills, Proper installation is the responsibility of the installer. Product tailure due to improper installation is not covered trader tile GE Appliance _,Varrantv.

See tile Owner's Manual fin" warranty infl)rmation.

WARNING:

• These refl'igerators are top-heavy and must be secm'ed to prevent the possibility of tipping forward. Anti-Tip protection is required. See page

l l fl)r details.

• Use this appliance only for its intended pm])ose.

• Immediately repair or replace electric service cords that become fl'ayed or damaged.

• Unl)lug tile refrigerator befln'e cleaning or making repairs.

• Repairs should be made by a qualified service technician.

AVERTISSEMENT

• Ces r_ffig_rateurs sont lom'ds en haut et il taut les arrimer pore" _\'iter leur basculement, ll taut a\'oir tm s):st_me de protection contre le renversement.

Voir les d_tails page 11.

• 11ne taut utiliser cet appareil que pore" l'utilisation aI)I)ropd_e.

• R_parer ou remplacer imm&liatement tout cordon _lectrique efliloch_ ou endommag_.

• 11taut d_brancher le r_frig_ratem" awmt le nettoyage ou route intervention.

• i,es r_parations doivent &tre taites par tm technicien qualifi_.

For Monogrmn local service in your area, call

1.800.444.1845.

For Monogrmn service in Canada, call

1.888.880.3030

For Monogrmn Parts and Accessories, call

1.800.626.2002.

www. monogram.corn

CONTENTS

PlanningGuide

The Installation Space ............................3

Dimensions and Clearances ..................3

130° Door Swing ......................................4

90° DoorSwing ........................................5

Customization Basics ..............................6

Panel Dimensions ....................................7

Side Panels................................................8

ZU62 Grille Panel Dimensions ..............8

InstallationInstructions

Tools,Hardware, Materials ....................9

6rounding the Refrigerator ....................9

Step 1, RemovePackaging ..................10

Step 2, Install Water Line......................10

Step 2A, ROWater Line ........................11

Step3, Install Side Panels ....................11

Step4, Install Anti-Tip Brackets..........11

Step 5, Level Refrigerator ....................12

Step6, Secure Refrigerator to

Cabinetry....................................12

Step 7, Adjust Door Swing ....................13

Step 8, Install Grille Panel ....................13

Step 9, Install FramedPanels ..............14

Step 9A, Install Overlay Panels............15

Step 10, ConnectWater Supply ..........16

Step 11, ConnectPower ........................16

Step 12,Start Icemaker ........................16

Step 13, Install Toekick..........................17

Design Guide

THE INSTALLATION SPACE

35-I/2"

FinishedWidth

The linished _1_ Wal,View

.to.t width/llg 2-8/1B''

mustbe /11 _T ,,

/ Im :8

maxL10

84-1/ ]] 75"From

83-1/2"min of ElectricalArea

Finished ]L_24" CutoutDepth ]] FloortoBottom Opening I ] E

I 115' WaterSupply_

| ])¢) _:: (_

_' 31/2" 31/2" '

Water And Electrical Locations

Electrical and water suppl) must be located as shown.

The cutout depth must be 24"

The refrigerator will project forward, slighfl_ bexond ac!iacent cabinetry, dei)ending, on _our installatilm.

Cutout depth beneath a soffit:

When installed beneath a soffit, the soffit cannot

exceed the 24" installation depth shown. The top case trim overlaps the bottom of the soffit.

Additional Specifications

• A 115 volt 60Hz., 15 or 20 amp power supply is required. An indMdual properly grounded branch

circuit or circuit breaker is recommended. Install a properly grounded 3-prong electrical receptacle

recessed into the back wall. Electrical must be located on rear wall as shown.

Note: GFI (ground tault interrupter) is not

recollllllended.

• Water line can enter the opening through the

floor or back wall. The water line should be 1/4" O.D. copper tubing or GE SlnartConnect ''_ kit

between the cold water line and water connection location, long enough to extend to the fl'ont of the

refl'igerator. Installation of an easily accessible sh ut-ott wflve in the water line is required.

DIMENSIONS AND CLEARANCES

35" 25-3/4"FramedModels

CaseWidth 25-3/4"StainlessSteelModels

CaseOept,,

_Shippingheight.The

--'_ ] refrigerator can be adjustedto fit intoa cutoutthat is

_'84"From 83-1/2"min.to 84-1/2" max.

_83-1'2"1 _ I Floorto height.Notethat thetop

TopFrame casetrim at the frontis

36_Fr'd 1/2" higherandwill overlap

uppercabinetryorsoffit. Uselevelinglegsandwheels foramaximum1" height adjustment.

" me to

FrameWidth

DepthIncludingHandles: 26-7/8"FramedModels 27-3/4"StainlessSteelModels

Product Clearances

These refrigerators are equipped with a 2-position

door stop. The factory set 130 ° door swing can be

a@Bted to 90 ° if clearance to a@_cent cabinets or

walls is restricted.

130° Door Swing

, 25"_

Minimum

to Wall

[,,,

130° ,

Allow 25" minimum clearance for a flfll

130 ° door swing. Allow 15" fl_r pan remoxal.

90° DoorSwing

, ]13_,/8,,

] Behind

/ Frame

L_ '[

(

!36-3/4"

90° :j

4" Minimum

toWall

4" minimum clearance is required when door swing

is a(!justed to 90 °. If the 90 ° door stop position is

used, pan access is maintained, but pan removal is restricted.

See illustrations pages 4 and 5 to deteHnine door swing

interaction with a@_cent cabinets or countertops.

ZUG2, ZUGSS2 Unified Grille Panel Kit

• If you are installing two reli'igerators, side b_,side,

the installation space must be 71-1/2" wide.

Note:Additional cutout width may be required when side panels are used. Addside panelthickness to the finished cutout to

calculate rough-in width.

• The water and electrical locations fl_r each product mtlst be located as shown.

• A separate l ISV, 60Hz., 15 or 20 amp power supply is recommended fin" each product.

-_71-1/2"FinishedWidth--

84-1/2"max

83-1/2"rain

Finished Opening

.............................

_)6" ; F6"

10" 10"

24"Cutout

Depttl

WaterSupply_5

_-/ 26"_ _26 "_

3-1/2"

WallView

75"From

Floorto Bottom

of ElectricalArea

3-1/2"

Design Guide

Refrigerator

Top View

130 ° DOOR SWING (factory setting)

Scale 1:1

23-7/8"From

Rearof

Refrigerator

Case Trim

Door

FramelessCabinets:The case trim overlaps cabinets at the top and sides.

Therefore, frameless cabinets may require filler strips to prevent interference with

cabinet door swing. The opening must allow for filler strips.

Design Guide

Refrigerator

Top View 90 ° DOOR SWING

(optional setting)

Scale 1:1

Door

CaseTrim

FramelessCabinets:The case trim overlaps cabinets atthe top andsides.

Therefore, frameless cabinets may require filler

strips to prevent interference with cabinet door swing. The

opening must allow for filler strips.

23-7/8"

FromRearof

Refrigerator

' ' 1/4".... t .... i.... t--

i i i i i

.... _ .... _ -- -- -- _ ..... 112

,,LiL ::

i i i .

................... 1 "

I ',:'::'_--I-1 --'_........... 1-1/

ell .....

, t .... _=t,--7-1--t ............. 1-1/2

i i

, I ,, ', ,, I ,,

,, I ,, ! ,, I ,, I

i i | i

i i i | i i i i i i

i i i i i

,, I ,, |

, I ' ' ' | ' i i i i

, I ' ' ' | '

i i

, , | ,

i i i i i

i I ' !

i 1 i i i i i i i i

i i i | i i i

i i i | i i i i i i

' I ' ' | ' 1 i i i i

I I 1 1 I ! 1

i i | i

i i i i i i i i | i

i i i | i i i i i i

i i i | i

.... I ...... 3/4 Overlay

I ,

' ' _ Panel

I i i i

i i " "

.... | (Nom,nalSize)

II' " " " I

1/2 ....

I ', ,' |

I ' ' !

I qt/l" ,,l

I _'C" ,, I I , I

I 1',,!

I ! ,

I | 1-1/4"

I I

Design Guide

CUSTOMIZATION BASICS:

Framed Or Overlay Panels, Custom Handles and Accessory Kits

Models Available

Stainless Steel Wrapped Models: ZICS360N RH (right-handed door) ZICS360N I,H (leli-handed door)

Trimmed models: ZIC360N RH (right-handed door)

ZIC360N I,H (lett-handed door)

Overlay panels

You may also choose to install custom overlay panels

fl'om your cabinet manufacturer. This design provides a seamless appearance which integrates smoothly with surrounding cabinetr>

Stainless Steel Wrapped Refrigerators

Stainless Steel wrapped refrigerators have wrapped doors and grille panel, beveled edges, and tubular

stainless steel handles that coordinate with other Monogram appliances. These models are shii)ped

readv for installation.

Trimmed Refrigerators

Trimmed refrigerators are designed to be customized with decorative panels. Field installed custom door and grille panels are required.

Overlay Panel Standard pacer Panel Door Handle I/4" Thick Backer Panel

Standard supplied handles shown in 3/4" overlay panel position.

Framed panels

You may install 1/4" thick custom panels from your

cabinet manufacturer. The decorative panel slides into the thctorv installed trim. Or, order black,

white and stainless steel accessory panels ti'om w)ur Monogram dealer.

Door and Drawer Handles

The standard supplied handles can be a(!iusted to accommodate both fl'amed or overlay panels. Custom handles of your choice, supplied by your cabinet maker can also be installed on overlay panels. If desired, you may order ZKHCSS2 Monogram stainless steel tubular handle kit tot 3/4" overlay panels.

Side Panels

Side panels must be used whenever the sides ol the refl'igerator will be exposed.

StandardDoorHandle FramedPanel

Standard supplied handles shown in 1/4"panel position.

Optional Accessory Kits

• ZKHCSS2: Monogram Tubular Stainless Steel handles designed to fit 3/4" overlay panels. This kit also

includes a handle side trim fi)r custom handles.

• ZUG2: For side-bwside installation of two trimmed bottom-freezer refrigerators. This kit provides tot the

installation of a unified custom grille panel to span the

width of two units using a framed or oveday panel.

• ZUGSS2: For side-by-side installation of two stainless steel wrapped bottom-ti'eezer refl'igerators. This kit

provides a unified stainless steel grille panel to span the width of two units.

Accessory Panels

White, black and stainless steel accessory panels are available fl'om your Monogram dealer. Panels are cut

to size and readv to install. ZPBC360-Black, ZPWC360-X4'hite,

ZPSC360-Sminless Steel Panels

+ 14 hidden pages

GE GE Monogram ZICS360N RH, Monogram ZIC360NRH, Monogram ZICS360NRH, Monogram ZICS360NLH Design Manual

Specifications and Main Features

Frequently Asked Questions

User Manual