GE CDWT980R10SS, GDWF100R10BB, GDWF100R10WW, GDWF100R30BB, GDWF100R30WW Installation Guide

...

GE CDWT980R10SS, GDWF100R10BB, GDWF100R10WW, GDWF100R30BB, GDWF100R30WW, GDWF160R10SS, GDWF160R30SS, GDWT100R05BB, GDWT100R05WW, GDWT100R10BB, GDWT100R10WW, GDWT100R30BB, GDWT100R30WW, GDWT160R05SS, GDWT160R10SS, GDWT160R30SS, GDWT200R10BB, GDWT200R10WW, GDWT200R30BB, GDWT200R30WW, GDWT260R10SS, GDWT260R30SS, GDWT300R10BB, GDWT300R10WW, GDWT300R30BB, GDWT300R30WW, GDWT360R10SS, GDWT360R30SS, GHDA690P04BB, GHDA690P04WW, GHDA696P04SS, GHDF300R10BB, GHDF300R10WW, GHDF360R10SS, GLD4404R00BB, GLD4404R00CC, GLD4404R00WW, GLD4406R00BB, GLD4406R00WW, GLD4408R00BB, GLD4408R00WW, GLD4456R00CS, GLD4458R00CS, GLD4464R00SS, GLD4466R00SS, GLD4468R00SS, GLD4500R00BB, GLD4500R00CC, GLD4500R00WW, GLD4550R00CS, GLD4560R00SS, GLD5600R00BB, GLD5600R00CC, GLD5600R00WW, GLD5660R00SS, GLD6904R10BB, GLD6904R10WW, GLD6906R10BB, GLD6906R10WW, GLD6908R10BB, GLD6908R10WW, GLD6964R10SS, GLD6966R10SS, GLD6968R10SS, GLD7400R10BB, GLD7400R10CC, GLD7400R10WW, GLDA690P02BB, GLDA690P02WW, GLDA690P03BB, GLDA690P03WW, GLDA696P02SS, GLDA696P03SS, GSD2100R00BB, GSD2100R00CC, GSD2100R00WW, GSD2100R15BB, GSD2100R15CC, GSD2100R15WW, GSD2101R00BB, GSD2101R00WW, GSD2101R15BB, GSD2101R15WW, GSD2300R00BB, GSD2300R00WW, GSD2300R15BB, GSD2300R15WW, GSD2301R00BB, GSD2301R00WW, GSD2301R15BB, GSD2301R15WW, GSD2340R00SA, GSD2340R15SA, GSD2350R00CS, GSD2350R15CS, GSD3300R00BB, GSD3300R00CC, GSD3300R00WW, GSD3300R15BB, GSD3300R15CC, GSD3300R15WW, GSD3360R15SS, GSD4000R00BB, GSD4000R00WW, GSD4000R15BB, GSD4000R15WW, GSD4060R15SS, GSM2200N15BB, GSM2200N15WW, GSM2260N15SS, PDWF600R10BB, PDWF600R10WW, PDWF600R30BB, PDWF600R30WW, PDWF680R10SS, PDWF680R30SS, PDWF800R10BB, PDWF800R10WW, PDWF800R30BB, PDWF800R30WW, PDWF880R10SS, PDWF880R30SS, PDWT100R10BB, PDWT100R10WW, PDWT100R30BB, PDWT100R30WW, PDWT180R10SS, PDWT180R30SS, PDWT300R10BB, PDWT300R10WW, PDWT300R30BB, PDWT300R30WW, PDWT380R10SS, PDWT380R30SS, PDWT400R10BB, PDWT400R10WW, PDWT400R30BB, PDWT400R30WW, PDWT480R10SS, PDWT480R30SS, PDWT500R10BB, PDWT500R10WW, PDWT500R30BB, PDWT500R30WW, PDWT502R10II, PDWT502R30II, PDWT505T10BB, PDWT505T10WW, PDWT505T30BB, PDWT505T30WW, PDWT580R10SS, PDWT580R30SS, PDWT585T10SS, PDWT585T30SS Installation Guide

04 _,Mf

Appliances

Installation Instructions

Built-In Dishwasher

If you have questions, call 800.GE.CARES(800.432.2737) or visit our Website at: GEAppliances.com In Canada call 1.800.561.3344 or www.GEAppliances.ca

BEFORE YOU BEGIN

Readthese instructions completely and carefully.

IM PORTANT Observeallgoverning codesand

ordinances.

• Note to Installer - Besure to leave these instructions for the consumer's and local inspector's use.

• Note to Consumer - Keep these instructions with your Owner's Manual for future reference.

• Skill Level- Installation of this dishwasher requires

basic mechanical, electrical and plumbing skills. Proper

installation is the responsibility of the installer. Product failure due to improper installation is not covered under the GEAppliance Warranty. Seewarranty information.

• Completion Time - 1to 3 Hours. New installations require more time than replacement installations.

READ CAREFULLY. KEEP THESE INSTRUCTIONS.

Stainless SteelTub Models

| L J l"_t'_ _'T'A k |'It

I Ivli_Ui_ | _l_l| - The dishwasherMUST

be installedtoallowforfutureremovalfromtheenclosure

if service is required.

If you received a damaged dishwasher, you should

immediately contact your dealer or builder.

Optional Accessories - See the Owner's Manual for available custom panel kits.

FOR YOUR SAFETY

Read and observe all CAUTIONSand WARNINGS shown throughout these instructions, While performing

installations described in this booklet, gloves and either safety glasses or goggles should be worn,

imagination at work

Installation Preparation

PARTS SUPPLIED WITH INSTALLATION KIT:

[] Two #8-18 x 5/8" Phillips special head screws, to

secure dishwasher to underside of countertop or

sides of cabinets. [] Junction box cover and #!0-1/2" hex-head screw [] Side and top trim

[] Trim Panel Accessorg Kit (not shown)

(Custom panel models onlg) [] Sound upgrade kit (some models) [] Drain hose (78"), drain hose hanger and hose

clamp [] Literature, product samples and/or coupons [] Hard water test strip (Models with Bulk Dispenser)

MATERIALS YOU WILL NEED:

[] Ferrule, compression nut and 90° Elbow (5/8" NPT

external thread on one end, opposite end sized to

fit water supplg)

[] Thread seal tape [] UL-listed wire nuts (3)

Screw Kit

#8 Phillips Special Head Screws

5/8" long

_ound Upgrade Kit

{Some Models)

tl Hard Water Test Strip

J(Models with

Bulk Dispenser)

90° Elbow, Hand Thread Wire Nuts (3) Ferrule and Shut-Off Seal Tape Compression Nut Valve

#10 Hex-Head J-Box Screw 1/2" long

Trim Pieces

Drain Hose Hanger

Drain Hose (78")

Side Trim

Top Trim

Junction Box Cover

Hose Clamp

Materials For New Installations Only:

[] Air gap for drain hose, if required [] Waste tee for house plumbing, if applicable [] Electrical cable or power cord, if applicable [] Screw-tgpe hose clamps [] Strain relief for electrical connection

[] Hand shut-off valve [] Water line 5/8" min. copper

[] Coupler for extending drain line, if applicable [] GPF10L !0' drain hose, if needed

TOOLS YOU WILL NEED:

[] Phillips-head screwdriver [] !/4" and 5/16" nutdriver

[] 6" Adjustable wrench [] Level

[] Carpenter's square [] Measuring tape [] Safetg glasses [] Flashlight [] Bucket to catch water when flushing the line

[] !5/16" socket [] Gloves

Waste Tee

_ Air

Gap

Head Screwdriver

114"and 15116" Socket

Hot Water Line

Electrical Cable (or Power Cord, if applicable)

Screw-Tgpe Strain Relief Coupler Hose Clumps

5/16" Nutdriver

6" Adjustable Tubing Cutter

Wrench Carpenter's

GPF20L 20' Drain Hose

Level

For New Installations Only:

[] Tubing cutter [] Drill and appropriate bits [] Holesaw set

Flashlight

Gloves

Safetg Glasses Measuring Tape

Bucket Hole Saw Set Drill and Bits

Installation Preparation-Enclosure

PREPARE DISHWASHER ENCLOSURE

To reducethe riskofshock,fire,orinjurg topersons,the installermust ensurethat thedishwasheriscompletelgenclosedat

thetimeof installation.

Pare reducir el riesgo de choque, incendio

o lesi6n a personas, el instalador se

debe cerciorar de que la lavadora est_ completamente cerrada en elmomento

de lainstalaci6n.

•The rough cabinet opening must have a minimum width

and depth of 24" and height of ]4-1/2" _+1/4" from the floor to the underside of the countertop.

• The back wall should be free of pipes or wires. Adjacent cabinets should be square and plumb to ensure a good fit. Referto Figure A

For a corner installation, allow 2" minimum clearance between the dishwasher and the adjacent wall.

Provide at least 28-5/8" in front of the dishwasher to allow the dishwasher door to open fully. Referto Figure B

• The dishwasher must be installed no more than 10 feet from sink for proper drainage.

The dishwasher must be fullg enclosed on the top, sides and back.

The dishwasher must not support any part of the enclosure.

[

Countertop

Dishwasher

28-3/8" Minimum

2" Minimum

Figure B

Clearances: In a corner installation, provide at

least 2" clearance between the dishwasher and the adjacent cabinet, wall, or other appliance.

Provide at least 28-3/8" of clearance in front of the dishwasher.

34-1/2" + 1/4"

Underside of

Countertop

to Floor

Squore

ond

J 24" Min:

Plumb

Floor MUST

be Even with

Room Floor

Figure A

Plumbing and Electric Service

Must Enter Shaded Area

• Moke sure the floor is level inside the opening and even with the finished floor of the kitchen. This will facilitate removal

of the dishwasher at a later date for service, if needed.

Special consideration for a dishwasher installed on a elevated platform The elevated platform must beflat and level.

InstallationPreparation-Drain

PREPARE DRAIN PLUMBING

Drain Requirements

• Drain hose must not exceed 10 feet in length.

• A high drain loop or air gap is required. See below.

Drain Method

The tgpe of drain installation depends on the following:

• Do local codes or ordinances require an air gap?

• Iswaste tee less than 18" above the floor? If the answer to either question is yes, an air gap must be used.

Referto Method 1 (Figure C)in the adjacent illustrations.

If both answers are no, either an air gap or high drain loop mag be used. Refer to Method 1 (Figure C)or Method 2 (Figure D) in the adjacent illustrations

NOTE: Drain hose elevation must not exceed 48".

Special consideration for a dishwasher installed on

a elevated platform

Ifthe dishwasher isinstalled on an elevated platform, a high

drain loop of at least 32" above the platform must be provided

in addition to the air gap or drain loop requirement determined

above. This is necessmrgfor proper drain performance.

METHOD 1-Air Gap with Waste Tee or Disposer

Figure C

Waste TeeInstallation

Disposer Installation

METHOD 2-High Drain Loop with Waste Tee

or Disposer

Usethe drain hose hanger included in the installation kit to attach the drain hose to the underside of the countertop. Attachment will be made in a later step.

in.

_ Figure D

Waste Tee Installation

DisposerInstallation

CAUTION

An air gap MUSTBEUSEDif the drain hose is connected to waste tee or disposer lower than 18" above the floor level.

Failure to provide the proper drain connection height with

an air gap or 32" minimum, high drain loop will result in

improper draining of the dishwasher, which may cause

damage.

PRECAUCION

SEDEBEUSARun espacio de aire si la manguera

de drenaje se conecta a la T de desechos o al triturador

menos de 18" por encima del nivel del piso. No disponer la altura correcta de la cone×i6n del drenaje con

un espacio de aire o 32" de minimo, una curva alta de drenaje resultar_ en un drenaje incorrecto de la lavadora, Io que pude causar da6os.

Install waste tee or disposer and the air gap according to the manufacturer's instructions.

Cabinet Preparation for drain line

Drill a 1-1/2" diameter hole in the cabinet wall within the shaded area shown in Figure A for the drain hose. Make

sure there are no sharp edges. The drain hose will be passed

through this hole and connected to the drain in a later step.

IMPORTANT-when

connecting the drain line to a disposer, check to be sure that drain plug has been removed.

Dishwasher will not drain if plug is left in place.

Drain

Plug

_ Remove

Installation Preparation-Electrical Supplg

PREPARE ELECTRICAL WIRING

FOR PERSONAL SAFETY: Remove house fuse

or open circuit breaker before beginning installation. Do not use an extension cord or

adapter plug with this appliance.

I I

/ I

Alternate q',

Receptacle , \

I \

Location

1-1/2" Dia.

Hole (Max.)

PARASEGURIDAD PERSONAL: Retire el

fusible de la casa o abra el interruptor de

circuitos antes de empezar la instalaci6n. No use un cable de extensi6n o enchufe

adaptador con este aparato.

Electrical Requirements

• This appliance must besupplied with 120V,60Hz., and connected to an individual properlg grounded branch circuit

protected bg a 15- or 20-ampere circuit breaker or time-

delag fuse.

• Wiring must be 2 wire with ground and rated for 75°C(176°F).

• If the electrical supplg does not meet the above

requirements, call a licensed electrician before proceeding.

Grounding Instructions-Permanent Connection This appliance must be connected to a grounded-metal,

permanent wiring sgstem, or an equipment-grounding

conductor must be run with the circuit conductors and be connected to the equipment-grounding terminal or lead on

the appliance.

Grounding Instructions-Power Cord Hodels This appliance must be grounded. Inthe event of a malfunction or breakdown, grounding will reduce the risk of electric shock

by providing a path of least resistance for electric current. This appliance is equipped with a cord having an equipment- grounding conductor and a grounding plug. The plug must

be plugged into an appropriate outlet that is installed and grounded inaccordance with all local codes and ordinances.

_The improper connection of the equipment

grounding conductor can result in a risk of electric shock. Check with a qualified

electrician or service representative if gou are in doubt that the appliance is properlg

grounded.

3" from

Cabinet

Location

Area

Figure E White

For models equipped with power cord: Do not modifg the plug provided with the appliance; if it will not fit the outlet, have a proper outlet installed by a qualified technician.

Cabinet Preparation and Wire Routing

• The wiring mag enter the opening from either side, rear or the floor within the shaded area dimensioned in Figure A

and illustrated above. Cut a !-!/2" max. diameter holeto admit the electrical cable.

Cable direct connections mag pass through the same hole as the drain hose and hot water line, if convenient. If cabinet

wall is metal, the hole edge must be covered with a bushing.

Note: Power cords with plug must pass through a separate

hole.

Electrical Connection to Dishwasher

Electrical connection is on the right front of dishwasher.

Forcable direct connections the cable must be routed as

shown in Figure E.Cable must extend a minimum of 24" from the rear wall.

Forpower cord connections, install a ]-prong grounding tgpe receptacle inthe adjacent cabinet rear wall, 6" min. or 18" max. from the opening, 6" to 18" above the floor. The receptacle must be accessible and therefore cannot

be installed in the back wall of the dishwasher enclosure.

La conexi6n incorrecta del conductor de

conexi6n a tierra del equipo puede resultar en choque el6ctrico. Consulte con un electricista calificado o representante

de servicio si tiene dudas de la conexi6n a tierra del aparato.

Installation Preparation-Hot Water Supply

PREPARE HOT WATER SUPPLY

Hot Water Line

• The line meg enter from either side, rear or floor within the shaded area shown in Figure F.

• The line meg pass through the same hole as the electrical cable and drain hose, or an additional 1-!/2" diameter hole

meg be cut to accommodate the water line. Ifa power cord

with plug is used, the water line must not pass through the

power cord hole.

I \

I \ I \ I \

/ I

_1-1/2" Oi,

ii Shut-off7

Valve Y

Hot_ i:::::::::: ,%.:',::',:':

:: L.

_2"

From

Cabinet

Hole

I__.!9" From Wall

I I

The hot water supplg line pressure must be at least 20 PSI.

Lower pressures could cause the water valve to leak and

cause water damage.

La linea de presi6n del suministro de ague caliente debe ser al menos 20 PSI.Presiones inferiores podrian causer que la v61vula del ague gotee g causer da_os por ague.

CAUTION

PRECAUCI6N

2" From Floor

CabinetFace_,-

Figure F

Water Line Connection

• Turn offthe water supplg.

• Install a hand shut-off valve in an accessible location, such as under the sink. (Optional, but stronglg recommended

and meg be required bg local codes.)

• The water connection is on the bottom-left side of the dishwasher. Install the hot water inlet line, using 3/8"

or larger copper tubing. Routethe line as shown in Figure F and extend forward at least 19" from rear wall.

• Adjust the water heater to deliver water between 120°F and !50°F.

• Flush water line to clean out debris. Use a bucket to catch water and debris.

• The hot water supplg line pressure must be between 20 and 120 PSI.

Dishwasher Installation

CAUTION

Do not remove the wood base until you are ready to install the dishwasher. The dishwasher will tip over

when the door isopened if the base is removed.

PRECAUCION

No retire la base de madera hasta que est_ listo para

instalar la lavadora de platos. Cuando la puerta se abra, la lavadora de platos se inclinar6 si la base se retira.

STEP 1 - LOCATE INSTALLATION ITEMS

• Locate the items in the installation package and set aside for use in the listed steps.

• Trim pieces - Step 2

Junction box cover - Step 7 or Step 18

Drain hose and clamp - Step 10 Screw Kit - Step 15

Drain hose hanger - Step 17 Owner's Manual - Step 19 and Step 24 Hard Water test strip - Step 21 Sound upgrade kit (selected models) - Step 22 Product samples and/or coupons - Step 24

Tgpe 1 - One-hole cable

Adjust tension bg moving spring hook to one of the three holes on the tub leg.

!INCREASE

DECREASE

One Hole

Figure H

Tgpe 2 - Three-hole cable

Adjust tension bg moving spring hook to one of the three holes on the pulley cable.

STEP 2 - INSTALL TRIM PIECES

Inthis step, gou will need the trim pieces set aside in Step 1.

Presstop trim piece onto top of tub flange. Start with the right edge and work gour wag to the left. Repeat process with the left and right trim pieces working

from the top down.

Open and close the door to check that trim does not bind and does not interfere with door latch or door hinges.

TrimStrip

Trim - Strip

Figure G

STEP 3 - CHECK DOOR BALANCE

• With dishwasher on the wood skid, check the door balance bg opening and closing the door.

If the door drops when released, increase the spring tension.

If the door rises when released, decrease the tension. There are two tgpes of counterbalance and therefore two methods of adjustment. Identifg which counterbalance is present and adjust tension accordinglg. Please note: Ifthere are 3 holes on the cable, use the cable to adjust; if there is one hole on cable, use the tub legto adjust.

Decrease

Increase

Figure I

After adjusting spring tension, open and close the door to

make sure the door operates smoothlg. If the door is hard to move or if the spring cable binds, check the routing of the spring cable. The cable should be routed between the

shoulders of the pulleg cable roller. If the cable isoff the roller:

latch door, remove spring tension and route the cable between the shoulders of the roller.See Figure J.

Pulle__

Shoulder

Figure J

Correct Spring Cable Routing

Tension

IncorrectSpring CableRouting 7

Dishwasher Installation

STEP 4 - REMOVE WOOD BASE,

INSTALL LEVELING LEGS

IMPORTANT- Donotkickoffwoodbase!Damage

will occur.

. Move the dishwasher close to the installation location and lag

it on its back.

• Remove the four leveling legs on the underside of the wood base with an adjustable wrench or 15/!6" socket.

• Discard base.

)rox.

Figure K

STEP 7 - INSTALL POWER CORD

Skip this step if dishwasher will be permanentlg connected to the house electrical sgstem. In this step gou will need the junction box cover and the

#!0 x !/2" hex-head screw from the screw kit set aside in Step i.

The power cord and connections must complg with the

National Electrical Code,Section/422 and/or local codes and ordinances. Maximum power cord length is 6 feet. Power Cord Kit wxogx70910, available for purchase from an authorized GEAppliance Dealer,meets these requirements.

Ground

. Screw leveling legs back into the dishwasher frame

approximatelg !/8" from frame as shown.

STEP 5 - REMOVE TOEKICK

• Removethe 2toekick screws and toekick.

Set aside for use in

Step 23.

_,emove 2

Figure L Toekick Screws

STEP 6 - REMOVE TOEKICK BRACE

Skip this step if your model does not have a sound upgrade kit. If your model does have a sound upgrade kit, this brace

must be removed.

• Remove the 2 toekick brace screws and

toekick brace.

Discard brace and set screws aside

for use in

Step 22.

Figure M

;emove 2

Toekick Screws

Figure N

• Install strain relief injunction box bracket.

• Insert power cord through strain relief and tighten. Make sure black, white and green dishwasher wires are threaded through small hole injunction box bracket. Connect like-colored dishwasher and power cord wires. If power cord wires are not color-coded, connect the ribbed power cord wire to the white dishwasher wire, the smooth power cord wire to the black dishwasher wire and the ground to the green dishwasher wire. Use UL-listed wire nuts of appropriate size. Install junction box cover set aside in Step 1, using #!0 hex- head screw. Besure wires are not pinched under the cover.

Dishwasher Installation

STEP 8 - INSTALL 90 ° ELBOW

• Wrap 90° elbow with thread seal tape.

• Install a 90° elbow onto the water valve. Front of Dishwasher

Water Valve

90°

Elbow

I Hose

Thread

Figure 0

• Do not overtighten the 90° elbow; water valve bracket could

bend or water valve fitting could break. Position the end of the elbow to face the rear of the

dishwasher.

Seal Tape

Bracket

STEP 9 - POSITION WATER LINE AND

HOUSE WIRING

• Position water supply line and house wiring

on the floor of the enclosure to avoid

interference with base of dishwasher

and components

under dishwasher.

STEP I0 - INSTALL DRAIN HOSE TO

DISHWASHER DRAIN PORT

In this step you will need the drain hose and clamp set aside in Step 1.

Stand dishwasher upright.

• Place drain hose clamp over 1-5/16" inside diameter end of drain hose with the clamp screw positioned on the bottom

of the hose.

IMPORTANT- Prevent drain hose damage and

possible leaks. Be careful not to nick or cut the drain hose.

Push the end of the drain hose over the drain pump outlet being careful not to disturb the check valve. Refer to Figure q). Seat the drain hose end against the hose stops on the pump

outlet. Position hose clamp against the front lip of the drain hose

and tighten clamp.

NOTE:Drain hose supplied with dish-

washer isapproxi- mately 78" long. Ifa longer hose is needed, a 120" long hose (!0 feet) may be purchased from

an authorized GEappliance

dealer.The !0' long

hose is port

number GPFIOL.

PumpOutlet HoseStop

Figure P

Figure Q

Tip: Avoid unnecessarg service charges. Makea leak free connection

Insert hose against stop on pump. Position clamp against front lip of drain hose with clamp screw on bottom side of hose. Tighten clamp to at least !5 inch-pounds of torque.

Tip: Reduce drain pump noise

Position drain hose clamp so screw is on the bottom side of the hose. This will prevent noise caused by the clamp coming in contact with the tub bottom. Refer to Figure q).

Dishwasher Installation

STEP 11 - INSERT DRAIN HOSE

THROUGH CABINET

• Position dishwasher in front of cabinet opening. Insert drain

hose into the hole in cabinet side. If a power cord is used, guide the end through a separate hole.

Drain

Hose Length 10'

Blanket

Hose

House Wiring

(If Power Cord

is NOT Used)

Power Cord

(If Used)

Figure R

Tip: Position water line and house wiring on the floor to avoid

interference with base of dishwasher.

STEP 12 - SLIDE DISHWASHER THREE-

FOURTHS OF THE WAY INTO CABINET

IM _UK i_l_l|- DO NOT PUSH AGAINST FRONT PANEL

WITH KNEES.DAMAGE WILL OCCUR.

',Grasp the dishwasher bg its sides and slide it into the opening

a few inches at a time.

o Not Push Against

Front Door Panel With Knee. Damage to The

Door Panel Will Occur.

Figure S

• As gou proceed, pull the drain hose through the opening under the sink. Stop pushing when the front of the dishwasher isa few inches forward of adjacent cabinets.

• Make sure drain hose is not kinked under the dishwasher and there is no interference with the water line,wiring or ang

other component.

Tip: Make sure the dishwasher will fit in the cabinet. Check to

be sure the power cable, drain hose and hot water line are not trapped behind the dishwasher. Utilitg lines trapped behind the dishwasher prevent the dishwasher from being pushed fullg

into the enclosure.

+ 22 hidden pages