GE GDF520P DO, GDF540H DO, WD35X10395GDF520P*D0, GDF540H*D0 Installation Instructions Manual

GE Appliances

Installation Instructions

Dry Enhancement Kit

WD35X10395

February 2013

Dishwasher Dry Performance

Verify proper heater operation, check for error
codes in diagnostic error mode, including
thermistor and/or wash temperature error codes.
Enter service mode to test heater operation. Full
directions to enter diagnostic and service mode
can be found in service guide 31-9226 or the

dishwasher's mini-manual.
If none of the above issues apply, follow all steps

in these instructions.

Models:

GDF520P DO
GDF540H DO

Parts Included:

This kit includes all parts needed for all models
listed above.

° U I Board (User Interface) WD21X10534
° 2 Vent Covers

° Foam Strip (black in color)
° Door Harness wire tie (may not be needed)

° Installation InstructionsWD00X1021

Step I - Remove Power from the
Dishwasher

Step 2 - Remove Inner Door Vent
Cover

To remove inner door vent cover, use 2 pocket
screw drivers, turn counter clockwise (Consult
Service Guide 31-9226 or Mini-manual). Old

vent cover should be discarded.

Step 3 - Remove complete Door
assembly

° Consult Service Guide 31-9226 or Mini-manual

for door removal process.

° A new wire tie for the door wire harness is

included in the kit. Should the original tie
become damaged, it must be replaced.

Tools You Will Need:

• 1/4" Nutdriver

• T15Torx scredriver

• Hinge locking tool (see service guide 31-9226)

GE Appliances
General Electric Company

Louisville, KY 40225

Step 4 - Separate the Door

° Consult Service Guide 31-9226 or Mini-manual

for door separation process.

WD00X1021

Step 5 - Remove Front Control
Console

• Consult Service Guide 31-9226 or Mini-manual
for console removal process.

Remove
protective

tape from the
bottom of the

foam strip.

Step 6 - Remove Vent Conduit

• Remove the 2 - T15 Torx screws to remove the
vent conduit from the front console.

• Vent conduit can now be removed.

Step 7 - Install new Ul Control Board
Control

Details on main control access can be found in
either Service Guide 31-9226 or Mini-manual

Verify correct model personality jumpers are in

correct position, keys/buttons and LED's will
not function until appropriate personality is

selected.

PERSONALITY

Place the strip inside the
bottom of the vent area of

the console.

Step 9 - Re-assemble Vent Conduit

Carefully insert the vent conduit into the vent
area of the front control, using care not to
damage the newly installed foam strip.

Reinstall 2 - T15 Trox screws

Step 10 - Re-assemble Inner to
Outer Door Panels

Reverse the dis-assembly procedure in the
Service Guide or mini-manual, make sure all
tabs are aligned and appearance of gaps is

correct.

Step 11 - Re-install Door

Install new UI and re-install assembly into top
console.

Step 8 - Install Foam Strip

This strip eliminates condensation pooling in the
outer vent area and must be installed.

• Make sure the vent area of the front control
console is clean and dry.

° Remove the protective paper from the foam

strip.

• Place the foam strip on the bottom of the vent
area of the console.

, Reverse door removal process to re-install the

door and connect the door wire harness.

Step 12 -Install new Vent Cover

• Install the new vent cover on the inner door to
vent conduit. This new vent cover allows more
air flow.

Step 13 - Test Operation

• Re-apply power, verify control and dishwasher
operation.