GE GDF510PGM0BB, GDF510PGM0WW, GDF510PSM0SS, GDF511PGM0BB, GDF511PGM0WW Installation Guide

...

Installation Instructions

Built-In Dishwasher

If you have questions, call GE Appliances at 800.GE.CARES (800.432.2737) or visit our website at: GEAppliances.com. In Canada, please call 800.561.3344 or visit geappliances.ca

BEFORE YOU BEGIN

Read these instructions completely and carefully.

WARNING

• Remove all power leading to the appliance from the

circuit breaker or fuse box before beginning installation. Failure to do so can result in a risk of electrical shock.

•

To reduce the risk of electric shock, fire, or injury to persons, the installer must ensure that the dishwasher is completely enclosed at the time of installation.

• The improper connection of the equipment grounding

conductor can result in a risk of electric shock. Check with a qualified electrician or service representative if you are in doubt that the appliance is properly grounded. If house wiring is not 2-wire with ground, a ground must be by the installer. When house wiring is aluminum, be sure to use UL-Listed anti-oxidant compound and aluminum-to-copper connectors.

•

To reduce the risk of electric shock, fire, or injury to persons, the installer should check to ensure that wires are not pinched or damaged, the house wiring is attached to the junction box bracket through a strain relief, and all electrical connections made at the time of install (wire nuts) are contained inside of

the junction box cover.

ADVERTENCIA

• Retire todos los conductores de corriente del

electrodoméstico de disyuntor o de la caja del fusible antes de comenzar con la instalación. Si no cumple con esto, se podrá producir el riesgo de descargas eléctricas.

• Para reducir el riesgo de descarga eléctrica, incendio

o lesiones a personas, el instalador debe asegurarse de que el lavaplatos esté completamente cerrado en el momento de la instalación.

• La conexión inadecuada del conductor de conexión a

tierra del equipamiento puede provocar un riesgo de descarga eléctrica. Consulte a un electricista calificado o representante de servicio técnico si tiene dudas sobre la correcta conexión a tierra del aparato. Si el cableado doméstico no cuenta con un cable de 2 hilos con conexión a tierra, un instalador debe realizar una conexión a tierra. Cuando el cableado doméstico es de aluminio, asegúrese de usar un compuesto antioxidante y conectores de aluminio a cobre aprobados por UL.

• Para reducir el riesgo de descarga eléctrica, incendio

o lesiones a personas, el instalador deberá realizar un control para asegurar que los cables no estén pellizcados ni dañados, que el cableado del hogar esté conectado a la ficha de la caja de empalmes a través de un amortiguador de refuerzo, y que todas las conexiones eléctricas realizadas en el momento de la instalación (tuercas para cables) estén dentro de la tapa de la caja de empalmes.

FOR YOUR SAFETY

Read and observe all WARNINGS and CAUTIONS shown throughout these instructions.

While performing installations described in this booklet, gloves, safety glasses or goggles should be worn.

IMPORTANT – Observe all governing codes and

ordinances.

• Note to Installer – Be sure to leave these instructions

for the consumer’s and local inspector’s use.

• Note to Consumer – Keep these instructions with

your Owner’s Manual for future reference.

• Skill Level – Installation of this dishwasher requires

basic mechanical, electrical and plumbing skills.

Proper installation is the responsibility of the installer. Product failure due to improper installation is not covered under the GE Appliances Warranty. See warranty information.

• Completion Time – 1 to 3 Hours. New installations

require more time than replacement installations.

IMPORTANT – The dishwasher MUST be installed to allow for future removal from the enclosure if service is required.

Care should be exercised when the appliance is installed or removed, power supply cord.

If you received a damaged dishwasher, you should immediately contact your dealer or builder.

Optional Accessories – See the Owner’s Manual for available custom panel kits.

Your dishwasher is a water heating appliance.

CHECK THE FOLLOWING

Tub trim does not interfere with the door Dishwasher is square and level at both the top and

bottom of the cabinet opening, with no twisting or distortion of the tub or door

All 4 legs of the dishwasher are firmly in contact with the

floor

Drain hose is not pinched between the dishwasher and

adjacent cabinets or walls

Tub trim is fully seated on the tub flange

to reduce the likelihood of damage to the

READ CAREFULLY

KEEP THESE INSTRUCTIONS

31-31586 03-18 GEA

Installation Preparation

PARTS SUPPLIED IN INSTALLATION PACKAGE:

• Junction box cover and #10 hex-head screw

• Hose clamp

• Drain hose (approximately 58” long)

• Drain hose hanger

• 2 #8-18 hex head screws to secure brackets to washer tub frame

• 2 Plug buttons

• Toekick (pre-installed on some models)

• 2 Tub trim pieces (on some models)

• 2 Mounting brackets for wood countertops or side cabinets

• 2 #8-18 x 5/8” Phillips special head screws, to secure dishwasher to underside of countertop or to side cabinets

• Insulation pieces (on some models)

• Literature, samples and/or coupons

MATERIALS YOU WILL NEED:

• ´*+7*DUGHQ+RVH7KUHDGÛHOERZLQFOXGLQJ

gasket) - with opposite end sized to fit Hot Water Line

• Thread seal tape

• UL-listed wire nuts (3)

• Masking tape

Materials For New Installations Only:

• Air gap for drain hose, if required

• Waste tee for house plumbing, if applicable

• Electrical cable or Power Cord Kit WX09X70910 (5’ 5” long) or WX09X70911 (7’ 11” long) depending on installation.

• Screw-type hose clamps

• Strain relief for electrical connection

• Hand shut-off valve (recommended)

• Hot Water Line–3/8” minimum, copper tubing (including ferrule, compression nut) or GE Appliances Part #

WX28X326, flexible braided hose.

• WD24X10065 drain hose (12’ long), if needed.

Junction

Box Cover

#8 Hex-Head

Mounting Bracket

Screws

Mounting

Brackets

#10

Hex-Head

Junction

Box Screw

1/2" long

Plug

Buttons

#8 Phillips

Special

Head Screws

5/8" long

GHT 90°Elbow

Waste Tee

Air Gap

Strain Relief

Thread

Seal Tape

(if applicable)

Hand

Shut-Off

Valve

Hose Clamp

Toe kick

Insulation

(on some models)

Wire Nuts (3)

Electrical Cable (or Power Cord,

if applicable)

Hot

Water

Line

Drain Hose

Drain Hose Hanger

Tub Trim Pieces

(on some models)

Literature

Masking Tape

Hose Clamps

Optional

12' Drain Hose

WD24X10065

Coupler for

optional drain hose

TOOLS YOU WILL NEED:

• Phillips-head screwdriver

• 1/4” and 5/16” nutdriver

• 6” Adjustable wrench

• Level

• Carpenter’s square

• Measuring tape

• Safety glasses

• Flashlight

• Bucket to catch water when flushing the line

• 15/16” socket (optional for skid removal)

• Gloves

• Pliers

For New Installations Only:

• Tubing cutter

• Drill and appropriate bits

• Hole saw set

Phillips-Head

Screwdriver

Measuring Tape

Tubing Cutter

1/4” and 5/16”

Nutdriver

Safety Glasses

15/16” Socket

Drill and Bits

6” Adjustable

Wrench

Flashlight

Gloves

Hole Saw Set

Level

Carpenter’s

Square

Bucket

Pliers

Installation Preparation

PREPARE DISHWASHER ENCLOSURE

This Wall Area Must be Free

34-1/2”+1/4”

33-1/2” to 34-3/4”

Underside of

Countertop

to Floor

of Pipes and Wires

Plumbing and Electric Service

Must Enter Inside This Area

24” Min.

• The rough cabinet opening must be at least 24” deep, 24” wide and approximately 34-1/2” high from floor to underside of the countertop.

• The dishwasher must be installed so that drain hose is no more than 12’ in length for proper drainage.

• The dishwasher must be fully enclosed on the top, sides and back, and must not support any part of the enclosure.

24” Min.

4”

Cabinets Square

6”

and Plumb

WARNING

To reduce the risk of electric shock, fire, or injury to persons, the installer must ensure that the dishwasher is completely enclosed at the time of installation.

ADVERTENCIA

Para reducir el riesgo de descarga eléctrica, incendio o lesiones a personas, el instalador debe asegurarse de que el lavaplatos esté completamente cerrado en el momento de la instalación.

CLEARANCES:

• When installed into a corner, allow 2” min. clearance between dishwasher and adjacent cabinet, wall or other appliances. Allow 25-1/2” min. clearance from the front of the dishwasher for door opening.

Countertop

Dishwasher

25-1/2"

Clearance for Door

Opening 2" Minimum

DRAIN REQUIREMENTS

• Follow local codes and ordinances.

• Do not exceed 12’ distance to drain.

• Drain connection height is not to exceed 72” above bottom of dishwasher.

NOTE : Air gap must be used if waste tee or disposer connection is less than 18” above floor to prevent siphoning.

DETERMINE DRAIN METHOD

The type of drain installation depends on the following questions.

• Do local codes or ordinances require an air gap?

• Is waste tee less than 18” above floor?

If the answer to either question is YES, Method 1 MUST be used.

•

If the answers are NO, either method may be used.

CABINET PREPARATION

• Drill a 1-1/2” diameter hole in the cabinet wall within the shaded areas shown in PREPARE DISHWASHER ENCLOSURE section for the drain hose connection. The hole should be smooth with no sharp edges.

IMPORTANT – When connecting

drain line to disposer, check to be sure that drain plug has been removed.

DISHWASHER WILL NOT DRAIN IF PLUG IS LEFT IN PLACE.

Remove Drain Plug

Method 1 – Air Gap with Waste Tee or Disposer

An air gap must be used when required by local codes and ordinances. The air gap must be installed according to manufacturer’s instructions.

Method 2 – “High Drain Loop” with Waste Tee or Disposer

Drain Hose Hanger

32"

Min.

18"

Min.

Drain Hose Hanger

32"

Min.

18"

Min.

Tip: Avoid unnecessary service call charges.

Always be sure disposer drain plug has been removed before attaching dishwasher drain hose to the disposer.

Installation Preparation

PREPARE ELECTRICAL WIRING

WARNING

Remove all power leading to the appliance from the circuit breaker or fuse box before beginning installation. Failure to do so can result in a risk of electrical shock.

ADVERTENCIA

Retire todos los conductores de corriente del electrodoméstico de disyuntor o de la caja del fusible antes de comenzar con la instalación. Si no cumple con esto, se podrá producir el riesgo de descargas eléctricas.

Electrical Requirements

• This appliance must be supplied with 120V, 60 Hz., and connected to an individual properly grounded branch circuit, protected by a 15- or 20-ampere circuit breaker or time-delay fuse.

• Wiring must be 2 wire with ground and rated for 167°F (75°C).

• If the electrical supply does not meet the above requirements, call a licensed electrician before proceeding.

Grounding Instructions–Permanent Connection

This appliance must be connected to a grounded metal, permanent wiring system, or an equipment-grounding conductor must be run with the circuit conductors and be connected to the equipment-grounding terminal or

lead on the appliance.

Grounding Instructions–Power Cord Models

This appliance must be grounded. In the event of a malfunction or breakdown, grounding will reduce the risk of electric shock by providing a path of least resistance for electric current. This appliance is equipped with a cord having an equipmentgrounding conductor and a grounding plug. The plug must be plugged into an appropriate outlet that is installed and grounded in accordance with all local codes and ordinances.

Alternate Receptacle Location in Adjacent Cabinet

18"

1-1/2" Dia. Hole (Max.)

24"

from Wall

Ground

Black

from

Cabinet

White

18"

Receptacle Location Area

For models equipped with power cord: Do not modify the plug provided with the appliance; if it will not fit the outlet, have a proper outlet installed by a qualified technician.

Cabinet Preparation & Wire Routing

•

The wiring may enter the opening from either side, rear

or the floor within the shaded area illustrated above in figure and defined in PREPARE DISHWASHER ENCLOSURE section.

• Cut a 1-1/2" maximum diameter hole to admit the electrical cable. Edges of hole should be smooth and rounded. Permanent wiring connections may pass through the same hole as the drain hose and hot water line, if convenient. If cabinet wall is metal, the hole edge must be covered with a bushing.

NOTE:

separate hole in the cabinet.

Power cords with plug must pass through a

WARNING

The improper connection of the equipment grounding conductor can result in a risk of electric shock. Check with a qualified electrician or service representative if you are in doubt that the appliance is properly grounded. If house wiring is not 2-wire with ground, a ground must be provided by the installer. When house wiring is aluminum, be sure to use UL-Listed antioxidant compound and aluminum-to-copper connectors.

ADVERTENCIA

La conexión inadecuada del conductor de conexión a tierra del equipamiento puede provocar un riesgo de descarga eléctrica. Consulte a un electricista calificado o representante de servicio técnico si tiene dudas sobre la correcta conexión a tierra del aparato. Si el cableado doméstico no cuenta con un cable de 2 hilos con conexión a tierra, un instalador debe realizar una conexión a tierra. Cuando el cableado doméstico es de aluminio, asegúrese de usar un compuesto antioxidante y conectores de aluminio a cobre aprobados por UL.

Electrical Connection to Dishwasher

Electrical connection is on the right front of dishwasher.

• For permanent connections the cable must be routed as shown in figure. Cable must extend a minimum of 24" from the rear wall.

• For power cord connections, install a 3-prong grounding type receptacle in the sink cabinet rear wall, 6" min. or 18" maximum from the opening, 6" to 18" above the floor.

• Use only WXO9X70910 (5’ 5” long) or WX09X70911

(7’ 11” long) Dishwasher Power Cord Kit. Do not use an extension cord or adapter plug with this appliance.

Installation Preparation

PREPARE HOT WATER LINE

NOTE: GE Appliances recommends copper tubing for

the water line, but if you choose to use flexible hose, use GE Appliances WX28X326, flexible braided hose.

• The water supply line (3/8” copper tubing or flexible

braided hose) may enter from either side, rear or floor within the shaded area shown in figure.

• The water supply line may pass through the same hole as the electrical cable and drain hose. Or, cut an additional 1-1/2" diameter hole to accommodate the water line. If power cord with plug is used, water line must not pass through power cord hole.

1-1/2”

Hot

Cabinet

Shut-off Valve

From

Dia.

Hole

19" From Wall

Water Line Connection

• If using a flexible braided supply hose, label the hose with the installation date to use as reference. Flexible braided hoses, elbows and gaskets should be replaced in 5 years.

• Turn off the water supply.

• Install a hand shut-off valve in an accessible location, such as under the sink. (Optional, but strongly recommended and may be required by local codes.)

• Water connection is on the left side of the dishwasher. Install the hot water inlet line, using no less than 3/8” copper tubing or a flexible braided hose. Route the line as shown in PREPARE HOT WATER LINE section and extend forward at least 19” from rear wall.

• Adjust water heater for 120°F to 140°F temperature.

• Flush water line to clean out debris.

• The hot water supply line pressure must be 20-120 PSI.

Turn page to begin dishwasher installation.

Cabinet Face

2" From Floor

Dishwasher Installation

STEP 1

PREPARATION

Locate the items in the installation package:

• Screws

• Junction box cover

• Drain hose and clamp

• Mounting brackets

• Trim pieces (on some models)

• Drain hose hanger

• Insulation pieces (some models)

• Toekick (pre-installed on some models)

• Owner’s Manual

• Product samples and/or coupons

STEP 2

• With dishwasher on the wood base, check the door balance by opening and closing the door.

• Door is properly balanced if, when opened, it self closes within 20° from vertical, stays in position from 20° to 70° and falls fully open beyond 70°.

• If necessary increase or decrease tension as shown. Latch door and adjust both springs to the same tension setting to correct balance.

CHECK DOOR BALANCE

Door closes within 20°

Door stays in position from 20° to 70°

Door falls fully open beyond 70°

Side View

STEP 3

REMOVE WOOD BASE, INSTALL LEVELING LEGS

CAUTION

Do not remove wood base until you are ready to install the dishwasher. The dishwasher will tip over when the door is opened if base is removed.

PRECAUCIÓN

No quite la base de madera hasta que esté listo para instalar el lavaplatos. Si se quita la base, el lavaplatos se volcará cuando se abra la puerta.

IMPORTANT – Do not kick off wood base!

Damage will occur.

• Move the dishwasher close to the installation location

and lay it on its back. NOTE: Do not place the dishwasher on its side.

• Remove the 4 leveling legs on the underside of the wood base with a 15/16” socket wrench.

• Discard base.

• Screw leveling legs back into the dishwasher frame, approximately 1/2” from frame as shown.

Side View

Make sure pulley cable is within pulley shoulders

Increase

Tension

Decrease

Tension

Tip: Make sure door opens and closes smoothly.

Check door opening and closing. If door does not open easily or falls too quickly, check spring cable routing. The cable is held in place by “shoulders” on the pulley. Check to be sure cable has not slipped over the pulley shoulders and is routed as shown.

Front View

STEP 4

REMOVE TOEKICK

Skip this step if the toekick is not preinstalled on the unit. On some models the toekick is packaged separately with the unit.

• Remove the 2 toekick screws and toekick. Set aside for use in Step 21.

Toekick

Remove 2

Toekick Screws

Approx

1/2"

Dishwasher Installation

STEP 5

• Thread 3/4” GHT 90° elbow onto the water valve. Ensure rubber gasket is located between valve and elbow.

• Do not overtighten elbow. Water valve bracket could bend or water valve fitting could break.

• Position the end of the elbow to face the rear of the dishwasher.

STEP 6

INSTALL 90° ELBOW

Front of dishwasher

Water Valve Bracket

90° Elbow

Fill Hose

INSTALL DRAIN HOSE TO

DRAIN LOOP

Connect drain loop end to drain hose using the screw clamp as shown in the figure.

STEP 7

POSITION WATER LINE AND HOUSE WIRING

• Position water supply line and house wiring on the floor of the opening to avoid interference with base of dishwasher and components under dishwasher.

STEP 8

Water

Line

INSTALL DRAIN HOSE,

House Wiring

THROUGH CABINET

• Position dishwasher in front of cabinet opening. Insert drain hose into the hole in cabinet side. If a power cord is used, guide the end through a separate cabinet opening.

Pull insulation

blanket over

collar

House Wiring

Power Cord

(If used)

Drain

Water Line

Ensure drain hose is not twisted or pinched

Maximum drain hose length is 15'

Do not disconnect or remove high drain loop from left side of dishwasher

Tip: Prevent unnecessary service call charges for fill, drain or noise concerns.

Position utility lines so they do not interfere with anything under or behind the dishwasher.

Reposition the insulation blanket over the collar, as shown.

Hose

Insulation

Blanket

Dishwasher Installation

STEP 9

SLIDE DISHWASHER

THREE-FOURTHS OF THE WAY INTO CABINET

IMPORTANT – Do not push against front panel with

knees. Damage will occur.

• Grasp the sides of the front panel and slide dishwasher into the opening a few inches at a time.

Do not push against front door panel with knee. Damage to the door panel will occur.

• As you proceed, pull the drain hose through the opening under the sink. Stop pushing when the dishwasher extends about 6 inches forward of adjacent cabinets.

• Make sure drain hose is not kinked under or behind the dishwasher.

• Make certain the house wiring, drain line and water line do not interfere with components under dishwasher.

STEP 10

INSTALL TRIM PIECES (on some models)

Skip this step if trim is not supplied with the dishwasher.

In this step you will need the trim pieces set aside in Step 1.

• Position the trim pieces so the lips face toward the dishwasher door.

• Select a trim piece and press it onto the left side tub flange. Start with the top edge and press the trim piece completely onto the tub flange as you move towards the bottom. Repeat for the right side tub

flange trim piece.

Trim Strip

Top View

Fully seat to tub flange

If you would like to order the Trim Kit from GE Appliances

Service, please call 800.GE.Cares (800.432.2737) and request part number WD08X10094 for BB models or

WD08X10096 for WW or CC models.

Dishwasher Installation

STEP 11

INSTALL MOUNTING BRACKETS

You will need the mounting brackets and 2 #8 hexhead screws set aside in Step 1.

You must install the mounting brackets onto the dishwasher tub frame top or sides prior to sliding the dishwasher into place under the countertop.

Install mounting brackets on top if the underside of countertop is wood or wood-like material that accepts screws:

IMPORTANT - After installing brackets and before

closing the dishwasher door, adjust the brackets by bending them up as needed, so that they do not contact the top of the dishwasher door and cause damage.

Top Mounting

#8 Bracket Screw

Bracket

Dishwasher tub frame

• If you are installing the dishwasher under a counter with a short overhang, the countertop brackets may extend beyond the edge of the counter. If this is the case, remove the excess length by repeatedly bending the brackets at the front notch only until they break.

Bend and break here after installing if counter has a short overhang.

STEP 11

INSTALL MOUNTING BRACKETS (CONT.)

Install mounting brackets on sides if the countertop is granite or similar material that will not accept wood screws:

• Break off front portion of the tab with pliers at the location shown prior to attaching to dishwasher.

• Position the left-hand side bracket as shown. Repeat with the right bracket.

Side Mounting

Dishwasher tub frame

#8 Bracket screw as supplied

Do not pinch the latch wires in #8 bracket screw

STEP 12

PUSH DISHWASHER INTO

Tub trim

Do not screw into cabinet face frame

Bend and break here if necessary

Bracket

FINAL POSITION

• Check the tub insulation blanket, if equipped, to be

sure it is smoothly wrapped around the tub. It should not be “bunched up” and it must not interfere with the door springs. If the insulation is “bunched up” or interfering with the springs, straighten and re-center the blanket prior to sliding the dishwasher into its final position.

• Slide the dishwasher into the final position by pushing on the sides of the door panel. Do not push or pull the door in a partially open or closed position when moving the dishwasher. Do not use a knee or push on the center of the panel. If you do, damage to the panel will likely result.

• The dishwasher is in the final position when the edges of the front panel are flush with the adjacent cabinets and the dishwasher is centered in the cabinet opening. Check that the dishwasher is squarely positioned in the cabinet opening at both the top and the bottom of the appliance prior to mounting to the cabinet.

IMPORTANT – Before opening the dishwasher door,

be certain the edges of the dishwasher door panel are behind the face of the adjacent cabinet and not up against the cabinet face. Refer to figure below. If the dishwasher door is opened when the edge of the door is against the face of the cabinet, dishwasher door damage and cabinet damage will occur.

Dishwasher Installation

STEP 12 STEP 13

• Check dishwasher alignment prior to opening dishwasher door to prevent panel damage.

• Open and close the dishwasher door to be sure it operates smoothly, and does not rub on the adjacent cabinet.

PUSH DISHWASHER INTO

FINAL POSITION (CONT.)

IMPORTANT – Dishwasher must be level for proper

dish rack operation, wash performance and door operation. The dishwasher must be leveled left to right and front to back. This ensures the dish racks will not roll in or out on their own, circulation water will flow to the pump inlet, and the door will close without hitting the side of the tub.

• Remove the lower dish rack and place a level on the door and lower rack track as shown in figure.

Door

Fits and

Swings

Back

Behind

Cabinet

Frame

Correct

Alignment

LEVEL DISHWASHER

Incorrect Alignment

will result in door damage

Door Catches

on Cabinet Frame

Tip: Prevent unnecessary service charges for panel damage or wash performance.

Make sure utility lines are not trapped or crushed behind dishwasher. Crushed lines will restrict water flow.

Check that tub trim does not contact the door at all points

Top

View

Tub trim may be trimmed if

necessary to ensure proper

door operation

Tub frame

Tub trim Cabinet Door

Handle

Do not allow tub trim to get

trapped by or come into

contact with the door

Top

View

Tub trim trapped by door!

•

Adjust the level of the dishwasher by individually turning the 4 legs on the bottom of the dishwasher as shown. Ensure all 4 legs are firmly in contact with the floor.

Turn Legs

to Adjust

• The dishwasher is properly leveled when the level indicator is centered left to right and front to back. Also, the dishwasher door should close without hitting the side of the tub.

• Replace the lower rack.

Tip: Prevent unnecessary service charges. Verify dishwasher is leveled.

Pull the dish racks half way out. They should stay put. Open and close the door. The door should fit in the tub opening without hitting the side of the tub. If the racks roll on their own, or the door hits the side of tub, re-level the dishwasher.

+ 22 hidden pages