GE GCG1500L0BB, GCG1500L0WW, GCG1700L0II, ZCGP150LII-00, ZCGS150LSS-00 Installation Guide
Installation
Instructions
15" Built-In Compactors
6C61580 SS
6C61500 BB
6061500 WW
GCG1700I1"
ZC6S150 SS
ZCGP150I1"
*For ZCGP150II and 6C61700 II,
also refer to the instructions
provided on the template packed
with those models.
Safety information
BEFORE YOU BEGIN
Read these instructions completely and
carefully.
• IMPORTANT- Save these instructions for
local inspector's use.
• IMPORTANT- Observe all governing codes
and ordinances.
Note to Installer - Be sure to leave these
instructions with the Consumer.
• Note to Consumer- Keep these instructions with
your Owner's Manual for future reference.
• Skill Level- Installation of this appliance requires
basic mechanical and electrical skills.
• Completion time - 1 hour.
• Proper installation isthe responsibility of the installer.
Product failure due to improper installation is not
covered under the Warranty. See Owner's Manual
for warranty information.
WARNING!
Do not allow items to fall or collect behind
the compactor. Failure to follow this
instruction could result in a fire.
CAUTION:
For personal safety, remove house fuse or
oven circuit breaker before beginning
installation to avoid severe or fatal
shock injury.
iMPORTANT
• Use this compactor only for its intended purpose.
• This compactor is designed for BUILT-IN
installations ONLY.
CONTENTS
Design Information
Models Available ..............................................................3
Product Dimensions and Clearances ............................3
Tools Required ..................................................................3
Parts Supplied ..................................................................3
Advance Planning
Clearances ........................................................................4
Models with a Custom Drawer Panel ..........................4
Installation Preparation
Electrical Requirements ................................................5
Grounding Requirements ................................................5
Unpacking the Compactor ..............................................6
Leveling the Compactor ..................................................7
Adjusting the Retaining Bracket ....................................7
Adjusting the Base Toekick ............................................7
Installation Instructions
Position the Compactor under the Countertop ............8
Attach the Compactor to the Countertop ....................8
Reinstall the Compactor Drawer ....................................9
Installation of the Trash Bag Caddy ..............................9
Finalize Installation ..........................................................9
2
MODELS AVAILABLE
Design information
GCG1580SS
*For ZCGP150II and GCG1700II, also refer
GCG1500BB
GCG1500WW
GCG1700I1"
ZCGS150SS
ZCGP150I1"
PRODUCT DIMENSIONS AND CLEARANCES
24" (61 cm)
min
Locate the outlet 18" (45.7 cm) rain
from the floor, 3" (7.6 cm} rain from
15-1/8"
(38.4cm)
min
34" (86.4cm)
to
35"
!88.9 cm)
either side
to the instructions provided on the template
packed with those models.
• Allow 23" (58.4 cm)
clearance atthe front for
a full drawer opening,
• Allow 6"(15.2 cm)
clearance on the right
side to the nearest
vertical wall or cabinet
for bag removal.
• Nete: This compactor is
33-3/4"
(85.8cm)
min.
to
35" (88.9 cm)
max.
designed for built-in
applications only.
TOOLS REQUIRED
.Level
• Phillips Screwdriver
• Pliers
•Gloves
• Measuring Tape
23" (58.4 cm)
PARTS SUPPLIED
• 6 mounting screws (located in the literature package)
• 2 countertop retaining brackets
• 2 side mounting clips
3
ADVANCE PLANNING
CLEARANCES
You should be able to fully open the compactor
drawer. Six inches (15.2cm)is required on the right
side of the compactor for bag removal.
• Allow 23 inches (58.4 cm) infront of the compactor
to remove the drawer.
This compactor is designed as a built-in
appliance only. It may be located in any
convenient space under a countertop.
DO NOT OPERATEFREE-STANDING.
The compactor may be installed beneath
countertops of stone or other materials that will
not accept screws. No trim kit is required.
The compactor must be securely installed in a cabinet
that is firmly attached to the house structure. Weight
on the compactor drawer could cause the compactor
to tip and result in injury. Never allow anyone to
climb, sit or hang on the compactor drawer.
MODELS WiTH A CUSTOM
DRAWER PANEL
Models ZCGP150 II and GCG1700 II
The custom drawer panel and custom handle of your
choice should be secured to the compactor before
installation begins. A template with instructions and
installation hardware is provided with those models.
For planning purposes, you may order the template in
advance. Order Pub. No. 31-30597. Complete panel
installation instructions are included on the template.
CUSTOM PANELSiZE REQUIREMENTS:
Maximum panel weight is 12 LBS (5.4 kg).
3/4"
(1.9 cm)
Thick
Custom 29-5/16"
Panel (74.5 cm)
_ 14-7/8"
(37.8 cm)
4
Loading...