GE GFSS2KEXASS, GFSL2KEXALS, GFSF2KEXAWW, GFSF2KEXACC, GFSF2KEXABB Owner’s Manual

...

ge.com

Safety Instructions ........... 2,3

Operating Instructions

Automatic Icemaker ............... 10

Care and Cleaning ............. 11, 12

Controls ............................ 4

Crispers and Pans ................... 7

Freezer ........................... 8, 9

Replacing the Light Bulbs .......... 13

Shelves and Bins .................... 6

Water Filter ......................... 5

Installation Instructions

Installing the Refrigerator ....... 15-19

Installing the Water Line ........ 28-30

Preparing to Install

the Refrigerator .................... 14

Removing and Replacing the Doors (Double Door

Refrigerator Models onlg) ....... 25-27

Removing and Replacing the

Freezer Drawer ................. 20, 21

Reversing the Door Swing (Single Door Refrigerator

Models onlg) ................... 22-25

Models 20, 22 and 23

Cong_lateur inf_rieur

R frig rateurs

La section franqaise commence 6 la page 43

Congelador inferior

Refrigeradores

Troubleshooting Tips ...... 31-34

Normal Operating Sounds .......... 31

Consumer Support

Consumer Support ........ Back Cover

Performance Data Sheet ........... 41

Product Registration

for Canadian Customers ........ B7, B8

Product Registration

for U.S. Customers ............. B5, B6

State of California Water

Treatment Device Certificate ....... /42

Warrantg for Canadian

Customers ......................... 40

Warrantg for U.S.Customers ....... B9

Write the model and serial numbers here:

Model #

Serial #

La secci6n en espahol empieza en la p6gina 81

Find these numbers on a label on the right side, near the top of the

refrigerator compartment.

200D9366PO04

49-60539 02-08 JR

IMPORTANT SAFETY INFORMATION. READ ALL INSTRUCTIONS BEFORE USING.

WARNING!

Use this appliance only for its intended purpose as described in this Owner's Manual.

SAFETYPRECAUTIONS

When using electrical appliances, basic safety precautions should be followed, including the following:

?,i:Thisrefrigerator must be properlu installed

and located in accordance with the Installation

Instructions before it is used.

:¢;_Donot allow childrento climb, stand or hang

on the shelvesin the refrigeraton They could damage the refrigerator and seriousluinjure

themselves.

::_¢Donot touch the cold surfaces in the freezer

compartment when hands are damp or wet. Skinmag stick to these extremelu cold surfaces.

?_:Donot store or usegasoline or other flammable

vapors and liquidsin the vicinity of this or any other appliance.

:¢;_Keepfingers out of the "pinch point" areas;

clearances between the doors and between the doors and cabinet are necessarilusmall.

Becareful closing doorswhen children are

in the area.

_:i,In refrigerators with automatic icemakers,

avoidcontact with the moving parts of the ejector mechanism, orwith the heating element

that releasesthe cubes.Do not place fingersor

hands on the automatic icemaking mechanism

while the refrigerator is plugged in.

::i_;Unplug the refrigerator before cleaning and making

repairs.

NOTE:Westrongly recommend that anb!servicing beperformed bbla qualifiedindividual.

_::,Setting either orboth controlsto the Off position

doesnot remove power to the light circuit.

_',:Donot refreezefrozen foods which have

thawed completelu.

DANGER! RISK OF CHILD ENTRAPMENT

PROPERDISPOSAL OF THE REFRIGERATOR

Childentrapment and suffocation are not problems of the past. Junked or abandoned refrigerators arestill

dangerous_.evenif they will sit for ':justa few dags." If Uouare getting rid of your old refrigerator,please

follow the instructions below to help prevent accidents.

Before You ThrowAway Your Old Refrigerator or Freezer:

ij_::Takeoff the doors. !;_:Leave the shelvesin place sothat children ma9 not

easiluclimb inside.

Refrigerants

All refrigeration products contain refrigerants, which under federal law must be removed prior

to product disposal. If gou are getting rid of an old refrigeration product, check with the compang

handling the disposal about what to do.

USEOFEXTENSIONCORDS

Because of potential safety hazards under certain conditions, we stronglg recommend against the use of on extension cord.

However,if you must use anextension cord, it is absolutely necessary that it be a UL-listed (inthe UnitedStates) or a CSAcertified (inCanada),3-wire grounding tgpe appliance extension cord having a grounding tgpe plug

and outlet and that the electrical rating of the cord be 15 amperes(minimum) and 120volts.

WARNING!

HOW TO CONNECT ELECTRICITY

Do not, under any circumstances, cut or remove the third (ground)prong from the power cord. For personal safety, this appliance must be properly grounded.

ge.com

The power cord ofthis appliance isequipped

with a 3-prong (grounding)plug which mates with a standard 3-prong (grounding)wall outlet to

minimize the possibilityof electricshock hazard from this appliance.

Have the wall outlet and circuit checked by a qualified electrician to make sure the outlet is

properly grounded. Where astandard 2-prong wall outlet isencountered,

it is your personalresponsibility and obligation to have it replaced with a properly grounded 3-prong

wall outlet.

The refrigerator should always be plugged into its

own individual electrical outlet which hasa voltage rating that matches the rating plate.

USEOFADAPTER PLUGS

Adapter plugs are not permitted in Canada.

Thisprovides the best performance and alsoprevents overloading house wiring circuits which could causea

fire hazardfrom overheated wires. Never unplug your refrigerator by pulling on the

power cord.Always grip plug firmly and pull straight out from the outlet.

Repairor replaceimmediately all power cords that have become frayed or otherwise damaged. Do not

use a cord that shows cracksor abrasion damage along its length or at either end.

When moving the refrigerator away from the wall, be careful not to rollover or damage the

power cord.

READAND FOLLOWTHISSAFETYINFORMATIONCAREFULLY. SAVETHESEINSTRUCTIONS

About the controls with temperature settings.

9_sCo_d_st __sCoLd_s_

(onsome models)

® o,o,, ® .J

Adjust Freezer Adjust RefrigerQtor

Temperature Temperature

NOTE: The refrigerator is shipped with protective film covering the digital temperature controls. If this film was not removed during installation, remove it now

9 is Coldest

(on some models)

Initiallg, set the refrigerator control at 5 and the freezer contro! at 5. Allow 2/4 hours for the temperature to stabilize. Several adjustments may be required. Adjust the controls one increment at a time, and allow 2/4 hours after each adjustment for the refrigerator to reach the temperature blOUhave set.

Setting either or both controls to 0 for digita! and 0 for the refrigerator control knob stops cooling in both the refrigerator and freezer compartments, but does not shut off electrical power to the refrigerator.

About the water filter. (onsome models) ge.com

Water Filter Cartridge

Thewater filter cartridge islocated in the

back upper right corner of the refrigerator

compartment.

Filter Bypass Plug

Youmust usethe filter bgpass plug when a replacement filter cartridge is not available.

The icemakerwill not operate without the

filter or filter bypass plug.

When to Replace the Filter

Thefilter cartridge should bereplaced when the flow of water to the icemaker

decreases,or everUsix months.

Installing the Filter Cartridge

0 If Uouarereplacing the cartridge, first

remove the oldone. Openthe cartridge

cover bg pressing in on the tab at the front and pullingdown.

Removethe cartridge bgslowlu rotating

it counterclockwise.Asmall amount of water mag drip down.

Replacement Filters: Toorderadditional filter cartridges

in the United States, visit our Website,

ge.com, or call GEParts and Accessories,

800.626.2002.

Filter Model GSWF Customers in Canada should consult

the Mellow pages for the nearest Mabe Service Center.

CAUTION: Ifoirhosbeen

trapped in the system, thefilter cartridge may be ejectedasit isremoved.Usecaution when

removing.

Removethe protective foil from the end

of the cartridge.

J j

Liningup the arrow on the cartridge

and the cartridge holder,slowlurotate the cartridge clockwiseuntil it stops.

When the cartridge isproperlu installed,

Uouwill feelit "click" asit locksinto place.

Thegrip on the end of the cartridge should be positioned verticallu.

Do not overtighten.

Closethe cartridge cover.

About the shelves and bins.

Not all features ore on oil models.

Rearranging the Shelves

Shelvesin the refrigerator compartment are adjustable.

Refrigerator Compartment

Toremove:

0 Removeall itemsfrom the shelf.

0 Tilt the shelfup at the front.

Liftthe shelf up at the back and

Some models have wire shelves that can be adjusted inthe same

monneF.

bring the shelfout.

Toreplace:

While tilting the shelf up, insertthe top

hook at the back of the shelf in a slot

on the track.

Lowerthe front of the shelf until the bottom of the shelf locks into place.

Non-Adjustable Shelves on the Door Ionsome models)

Toremove: Lift the shelf straight up; then

pull out. Toreplace: Engagethe shelf inthe molded

supports on the door and push down. It will lockin place.

About the crispers and pans. ge.com

Not all features are on all models.

Fruit and Vegetable Crisper

Excesswater that may accumulate in the bottom of the drawers or under the drawers

should bewiped dru.

Adjustable Humidity Crisper Ionsomemodels)

Slidethe control allthe wag to the Slidethe control all the wag to the LOW HIGHsetting to provide high humiditg setting to provide lower humiditg levels

recommended for most vegetables, recommended for mostfruits.

Snack Pan (onsomemodels)

This pan can be moved to the most useful

location for gour familg's needs.

Toremove, slide the pan out to the stop position,liftthe pan up and past the stop

position and lift it out.

About the freezer drawer. (onsomemodels)

Not all features are on all models.

Freezer Shelves and Baskets

Appearance and features mag varg

Appearance may varg

0 A shelfabove the ice storage bin 0 A half-width basket

A deep full-width basket

Basket Removal

Toremove thedeep full-width basket on freezer drawer models:

Openthe freezer drawer until it stops.

Thefreezer basket restson the inside

tabs on the drawer slides. Liftthe basket so that it is out of all

6 slidebracket tabs.

Tilt the basket and lift out ofthe drawer

To remove the half-width basket:

Pullthe basket out to the stop location. Liftthe basket up at the front to release

it from the stop hooks on each side. Liftthe basket out to remove it from

the sides.

NOTE: Do not fill baskets higher than the rim of the basket. This may cause baskets to stick

or jam when opening or closing.

When replacing the deep full-width basket:.

Tiltthe basket back and lower it down into the drawer Rotate the basket to a

horizontal position and press it down into the 6 alignment tabs.

NOTE:Alwags be sure that the basket is seated in all 6 slide bracket tabs before sliding

back into the freezer The basket can be turned in either direction front to back and

installed into the freezer

When replacing the basket, make surethat the basket goes under the stop hooks on

each side. NOTE:Alwagsbe sure to fullg closethis

basket.

Appearance mag varg

About the freezer compartment. (onsome models) ge.eom

Not all features are on all models.

Freezer Shelf and Basket

0 A full-width fixed wire shelf 0 A full-width slidingwire basket

Basket Removal

Toremove the full-width slidingwire basket

on door models:

Openthe basketout to its full extension. Lift up the front of the basket and pull

straight out to remove.

Fixed Shelf Removal

NOTE:Thefull-width wire shelf is not intended

to slide. Toremove for cleaning:

Holdthe shelf at the front and pull it firmlu forward.

NOTE:Do not fillbasket higher than the rim of the basket. Thismau cause basket to stick or

jam when opening or closing.

When replacing the full-width sliding wire basket:

Insertthe wire basket into the lowerliner's railsand push back into place.

When replacing the full-width sliding wire shelf:

Insertthe wire shelf into the upper liner's rails and push backinto place.

To remove

To replace

Non-Adjustable Shelf on Freezer Door

Toremove: Lift the shelf straight up;

then pull out, Toreplace: Engagethe shelf inthe molded

supports on the door and push down.It will lock in place.

About the outomotic icemoker (onsome models)

A newlg installed refrigerator mog take 12 to 24 hours to begin making ice.

Switch

Power FeelerArm

Light

To reach the power switch.

Automatic Icemaker

Icemaker Theicemakerwillproducesevencubespercgcle-

approximatelg100-130cubesina 24-hourperiod, dependingonfreezercompartmenttemperature,

roomtemperature,numberofdooropeningsand otheruseconditions.

Seebelowfor howto accessiceandreachthe powerswitch.

Iftherefrigeratorisoperatedbeforethewater connectionismadetotheicemaker,setthe power

switchintheO(off)position.

Whenthe refrigeratorhas beenconnectedto thewatersupplg,setthepowerswitchto the! Ion)

position.Theicemakerpowerlightwillturn green whenthe freezerlightswitchis pressedinor when thefreezerdoorisclosed.

Theicemakerwillfill withwaterwhenitcoolsto

15°F(-10°C).Anewlginstalledrefrigeratormag take 12to 24hoursto beginmakingicecubes.

AthCCessing Ice and Reaching

e Power Switch

Toreach the icemaker power switch, pull

the shelf above the icebin straight out. Alwags

be sure to replacethe shelf. Toaccess ice, simplgpullthe binforward.

Youwillheara buzzingsoundeachtime the icemakerfillswithwater.

Throwawagthe firstfew batchesof iceto allow thewaterlineto clean

Besurenothinginterfereswiththesweep ofthe feelerarm.

Whenthe binfillstothe levelofthefeelerarm, the icemakerwillstopproducingice.Itis normal

for severalcubesto bejoinedtogetheE

Ificeis notusedfrequentlg,oldicecubeswill becomecloudg,tastestaleandshrink.

NOTE"Inhomeswithlower-than-overagewater

pressure,you mayheartheicemokercyclemultiple

timeswhenmakingonebatchdice. NOTE:Setthepowerswitchtothe0 (off)position

ifthewatersupplyisshutoff

lY--.........T

To access ice.

Icemaker Accessory Kit

Ifgourrefrigeratordid notcomealreadgequipped withanautomaticicemaker,an icemaker

accessorgkitisavailableatextracost.

Checkthe backoftherefrigeratorforthespecific icemakerkitneededforgourmodel.

Care and cleaning of the refrigerator, geeom

Cleaning the Outside

Thedoor handles and trim. Cleanwith a

cloth dampened with soapywateE Drywith a soft cloth. Do not usewax on the door

handlesand trim.

Keepthe outside cleon. Wipe with a clean cloth lightly dampened with kitchen

appliance wax or mild liquid dish detergent.

Dry and polishwith a clean,soft cloth.

Do not wipe the refrigerator with o soiled dish cloth or wet towel. Thesemay leave o residue that con erode the point. Do not

use scouring pads, powdered cleaners, bleach or cleaners containing bleach

because these products con scratch and weaken the point finish.

Cleaning the Inside

To helpprevent odors,leavean open box

of baking soda in the refrigerator and freezer compartments.

Unplug the refrigerator before cleaning.

Ifthis isnot practical, wring excessmoisture

out of sponge or cloth when cleaning around switches, lights or controls.

Usean appliance wax polishon the inside

surface between the doors.

Usewarm water and bakingsoda solution- about a tablespoon (15ml)of baking sodato a quart (1liter)ofwateEThisboth cleansand

neutralizesodors. Rinseand wipe dry.

Thestainless steel panels and door handles. Stainlesssteel (onsome models)

can be cleaned with a commercially available stainlesssteel cleaner A spray-on

stainlesssteel cleaner works best. Donot use appliance wax or polish

on the stainlesssteel.

After cleaning the door gaskets,apply a thin

lager of petroleumjelly to the door gaskets at the hinge side.Thishelps keepthe gaskets

from sticking and bending out of shape.

Avoid cleaning cold gloss shelves with hot

water because the extreme temperature difference may cause them to break. Handle glass shelves carefully. Bumping tempered gloss con cause it to shatter.

Do not wash any plastic refrigerator ports in the dishwasher.

Careand cleaning of the refrigerator.

Behind the Refrigerator

Becareful when moving the refrigerator away from the wall.All types of floor

coveringscan be damaged, particularlu cushioned coverings andthose with

embossedsurfaces. Raisethe levelinglegs located at the bottom

front of the refrigeratoE Pullthe refrigerator straight out and return it

to position bgpushing it straight in. Moving

Preparing for Vacation

the refrigerator in a side direction mug result in damage to the floor covering

or refrigeratoE Lower the levelinglegs untilthey touch

the flooE

When pushing the refrigerator back, make sure gou don't roll over the power cord or

icemaker supplg line (on some models).

Forlong vacations or absences,remove food and unplug the refrigeratoECleanthe

interior with a baking soda solution of one tablespoon (15ml)of baking soda to one

quart (1liter)of wateE Leavethe doors open. Setthe icemaker power switch to the 0 (off)

position and shut off the water supplg to the refrigeratoE

Preparing to Move

Secureall loose items such asbase grille, shelvesand drawers bg taping them

securelg in placeto prevent damage. When using a hand truck to move the

refrigerator,do not rest the front or back of the refrigerator against the hand truck.

This could damage the refrigeratoEHandle

onlg from the sidesof the refrigeratoE

If the temperature can drop below freezing, have a qualified servicer drain the water

suppl Usgstem (on some models) to prevent serious propertg damage due to flooding.

Be sure the refrigerator stags in an upright position during moving.

Replacing the light bulbs, gecom

Turning the control to the Off position does not remove power to the light circuit.

Refrigerator Lights

(

Appearance may vary

Ik CAUTION:Light bulbs may

be hot.

0 Unplug the refrigerator. 0 To remove the light shield, grasp the

shield at the back and pull out to release

the tabs at the back.

df_ Rotate the shield down and then forward

to release the tabs at the front of the shield.

Freezer Light

.ZlCAUTION:Light bulbsmay

be hot.

Unplug the refrigerator.

The bulb is located at the top of the

freezer inside a light shield. To remove the shield, grasp the shield at the back and

pull out to release the tabs at the back. Rotate the shield down and then forward

to release the tabs at the front of the shield.

After replacing with an appliance bulb

of the same or lowerwattage, replace

the shield.

Plugthe refrigerator back in.

NOTE:Appliancebulbs may be ordered from GEParts and Accessories,800.626.2002.

After replacing with an appliance bulb

of the same or lowerwattage, replace

the shield.

Plugthe refrigerator back in.

Installation

Refrigerator

Instructions

I Questions? Call 800.GE.CARES (800.432.2737) or Visit our Website at: ge.com

BEFORE YOU BEGIN

Read these instructions completely and carefully.

• IMPORTANT - savetheseinstructions

for local inspector's use.

• IN PORTANT - Observeallgoverning

codes and ordinances.

• Note to Installer-Be sure to leavethese

instructions with the Consumer.

• Note to Consumer- Keep these instructions for future reference.

• Skill level - Installation of this appliance requires basic mechanical skills.

• Completion time - Refrigerator Installation

In Canada, call 1.800.561.3344 or Visit our Website at: www.geappliances.ca

TOOLS YOU MAY NEED

Adjustable Wrench

1/4" Outer Diameter

Compression Nut

and Ferrule (sleeve)

(icemakermodelsonl9)

20 minutes Water Line Installation

30 minutes

3/32", 1/8" and 3/16" Allen

Models 20 and 22

3/8" and 5/16" Socket

Ratchet!Driver

Phillips Head Screwdriver

wrenches

• Proper installation is the responsibilitg of the installen

• Product failure clue to improper installation is not covered under the Warrantg,

PREPARATION

MOVING THE REFRIGERATOR INDOORS If the refrigerator will not fit through a doorwag,

the refrigerator door and freezer drawer can be removed.

° To remove the refrigerator door, see Step 1 in

the Reversing the Door Swing section.

• To remove the freezer drawer, see the Removing the Freezer Drawer section.

WATER SUPPLYTO THE ICEMAKER AND DISPENSER (ON SOME MODELS)

If the refrigerator has an icemaker, it will have

to be connected to a cold water line. AGE water supplg kit (containing tubing, shutoff valve, fittings

and instructions) is available at extra cost from gour dealer, bg visiting our Website at ge.com

(in Canada at www.geappliances.ca) or from

Parts and Accessories, 800.626.2002

(In Canada 1.888.661.1616).

1/8" Drill Bit and

Electric or Hand Drill

Pencil

Wire Cutters

Tapemeasure

1/4" Nut Driver

Level

Installation Instructions

INSTALLING THE REFRIGERATOR

REFRIGERATOR LOCATION

• Do not install the refrigerator where the temperature will go below 60°F (16°C)because it will not run often

enough to maintain proper temperatures.

• Do not install the refrigerator where the temperature will go above IO0°F(37°C)because it will not perform

properlg.

• Install it on a floor strong enough to support it fullg loaded.

CLEARANCES

Allow the following clearances for ease of installation, proper air circulation and plumbing and electrical

connections.

Standard Depth

Models Sides 1/8" (3mm) Top 1" (25 mm)

Back 1" (25 mm)

REMOVETOPCAP(cont.)(onsomemodels)

REINSTALL DOORS, DRAWERS AND TOP CAP

[] Carefully lower the door(s)onto the center hinge(s).

Reinstalltop hinge(s).NOTE: Ensurethe door is properly aligned to the case top to avoid readjustment of the door during top cap

reinstallation.

[] Place cap over the top of the refrigerator. Reinstall

the original screws in the top and back of the cap.

[] Reinstall the bottom freezer drawer or door. Referto

"Replacing the Freezer Drawer" section or Step 8 of "Reversing the Door Swing" section.

REMOVETOPCAP(onsomemodels)

• IMPORTANTNOTE:Thisrefrigerator is 34-1/2" deep. Doors and passagewags leading to the installation

location must be at least 36" wide in order to leave

the doors and handles attached to the refrigerator while transporting it into the installation location. If

passagewags are lessthan 36", the refrigerator doors

and handles can easilg be scratched and damaged. The top cap and doors can be removed to allow the

refrigerator to be safely moved indoors. Start with Step A.

• If it is not necessary to remove doors, skip Step A. Leave tape and all packaging on doors until the

refrigerator is in the final location.

• SKIDREMOVAL:Tilt refrigerator to each side to

removeskid.

• NOTE:Use a padded hand truck to move this refrigerator. Place the refrigerator on the hand truck

with a side against the truck. We strongly recommend that TWO PEOPLEmove and complete this installation.

[] Locate and remove the two Phillips head screws on

the top of the refrigerator. Remove the two screws on each side at the rear of the top cap. Lift off and

remove top cap.

[] Remove the fresh-food door(s).Referto Steps i and 3

of "Reversing the Door Swing" section or Steps i and

2 of "Removing the Doors" section.

[] Remove the bottom freezer drawer or door. Referto

"Removing FreezerDrawer" section or Step 2 of "Reversing the Door Swing" section.

[] Move refrigerator to the installation location.

CONNECTING THE REFRIGERATOR

[]

TO THE HOUSE WATER LINE

(icemaker models)

A cold water supply isrequired for automatic icemaker operation. If there is not a cold water

supply, you will need to provide one. SeeInstalling the Water Line section.

NOTES:

• Before making the connection to the refrigerator, be sure the refrigerator power cord is not plugged

into the wall outlet.

• If your refrigerator does not have a water filter, we recommend installing one if your water supply has

sand or particles that could clog the screen of the refrigerator's water valve. Install it in the water line

near the refrigerator. If using GESmartConnecf" Refrigerator Tubing Kit, you will need an additional tube (WXO8XIO002)to connect the filter. Do not cut

plastic tube to install filter.

Top Hinge B

Installation Instructions

INSTALLING THE REFRIGERATOR(cont.)

[] CONNECTING THE REFRIGERATOR TO

THE HOUSE WATER LINE

(cont.)

[] If gou are using copper tubing, place a

compression nut and ferrule (sleeve) onto the end of the tubing coming from the house cold water supplg.

If gou are using the GESmartConnect T" tubing, the nuts are alreadg assembled to the tubing.

[] If you are using copper tubing, insert

the end of the tubing into the refrigerator connection, at the back of the refrigerator, as far as possible. While holding the tubing, tighten the fitting.

If gou (]re using GE SmartConnect" tubing, insert the molded end of the tubing into the refrigerator connection, at the back of the refrigerator, and tighten the compression nut until it is hand tight. Then tighten one additional turn with a wrench. Overtightening mac cause leaks.

[] Fasten the tubing into the clamp provided to

hold it in position. You mac need to prg open the clamp.

One of the illustrations below will look like the connection on gour refrigerator.

[] TURN ON THE WATER SUPPLY

(icemaker models)

Turn the water on at the shutoff valve (house water supply) and check for anu leaks.

[] PLUG IN THE REFRIGERATOR

On models with an icemaker, before plugging in the refrigerator, make sure the icemaker power switch is set to the 0 (off) position.

See the grounding information attached to the power cord.

Icemaker-Readg models

Tubing

Clamp

i/4"

Compression

Nut

Ferrule

(sleeve)

Refrigerator

Icemaker-lnstalled Models

Refrigerator (sleeve) Compression Connection --

SmartConnecf"

Tubing

SmartConnect T"

Tubing

Ferrule 1/4"

1/4" Copper

1/4" Tubing

1_'1PUTTHEREFRIGERATORIN PLACEHove the refrigerator to its final location.

[] LEVEL THE REFRIGERATOR

Adjustable legs at the front corners of the refrigerator should be set so the refrigerator is firmlg positioned on the floor, and the front is raised just enough that the door closes easilg when opened about halfwag.

To adjust the leveling legs, turn the legs

clockwise to raise the refrigerator, counterclockwise to lower it.

TubingClamp

Installation Instructions

[] REMOVE THE FRESH FOOD

DOOR HANDLE

(For placement in the installation location or reversal of the handles - on some

models)

Stainless steel (on some models): O REMOVING

THE DOOR

HANDLE: Loosen the set screws with the 3/32" Allen wrench

and remove the handle.

NOTE: For

Double Door Mounting

models follow Fasteners the same

procedureon the oppositedoon

(appearancemay vary)

[] REMOVE THE FREEZER DOOR HANDLE

Stainless steel and plastic handles:

O Loosen the set screws located on the

underside of the handle with the 1/8" Allen

wrench and remove the handle.

NOTE: If the handle mounting fasteners need

to be tightened or removed, use a 3/16" Allen wrench.

Badge

Plastic handle (on some models): @ REMOVING THE DOOR HANDLE: Depress the

tab on the underside of the handle and slide the handle up and off of the mounting

fasteners.

Q REVERSINGTHE

DOOR HANDLE

(on some

models):

• Remove the handle

mounting

fasteners with a 3/16" Allen wrench and transfer the handle

mounting

fasteners to the right side.

• Remove the logo badge.

• Remove and transfer the plug button to the left side of the fresh food door. NOTE:

Use a flat plastic edge to prevent damaging the door. Remove any adhesive on the door with a mild detergent. Remove the paper covering on the adhesive backing on the logo badge prior to carefully attaching the badge to the door.

Mounting Fasteners

(appearance may vary)

Badge

-y

Installation Instructions

INSTALLING THE REFRIGERATOR(cont.)

[] ATTACH THE FRESH FOOD

DOOR HANDLE

Stainless steel handle: 0 Attach the

handle to the handle mounting

fasteners and tighten the set

screws with a 3/32" Allen

wrench.

NOTE: For Double Door models follow

the same

procedure on the opposite door.

Plastic handle: O Attach the handle to the handle mounting

fasteners bg aligning the slots with the

handle mounting fasteners.

@ Slide it down until it is firmly locked into

position.

Mounting Fasteners

(appearance may vary)

[] ATTACH THE FREEZER DOOR HANDLE

Stainless steel and plastic handles: @ Attach the handle firmlg to the mounting

fasteners and tighten the set screws on the bottom of the handle with a 1/8" Allen wrench.

,. 1/J

(appearance may vary)

Slots on back of handle

Hounting fasteners

(appearance may vary)

Installation Instructions

[] LEVEL THE REFRIGERATOR

The leveling legs have 2 purposes:

1) Leveling legs odjust so the refrigerotor is firmlg positioned on the floor and does not

wobble.

2) Leveling legs serve Gsa stabilizing brGke to hold the refrigerator securelg in position during operotion ond cleoning. The leveling

legs olso prevent the refrigerator from

tipping.

[] Remove the grille bg removing the two Phillips

head screws.

[] SET THE CONTROLS

Set the controls to the recommended setting.

bCOMMENOEOCON'ROLSE'T'"OS]

oisoff o_off

C!°'°ir_8 (Wormo_(!°"e00 (Wormor_

_,CDrd_,t 9_,Cold_,t

5 5

IRECOMMENOEOCO"'RO"SETT'"OS]

[] Turn the leveling legs clockwise to raise

the refrigerator, counterclockwise to lower it.

./i CAUTION: To avoid possible

personal injurg or propertg damage, the leveling legs must be firmlg touching

the floor.

[] Replace the base grille bg inserting the two

Phillips head screws.

AdjustFreezer AdjustRefrigerator

Temperature Temperature

[_] REMOVE PACKAGING, START

ICEMAKER (icemaker models)

A) Remove all tape, foam and protective

packing from shelves and drawers.

B) Remove the tie downs from the freezer

baskets.

C) Place half width basket onto drawer slides.

See About the freezer section for instructions.

Setthe icemaker power switch to the I (on) position. The icemaker will not begin to operate until it reaches its operating temperature of 1S°F (-9°C) or below. It will then begin operation automatically. It will take 2-3 dags to fill the ice bin.

NOTE: In lower water pressure conditions, the water valve mag turn on up to 3 times to deliver enough water to the icemaker.

Installation Instructions

REMOVING THE FREEZER DRAWER (onsome models)

[]

The freezer drawer can be removed, if needed,

to fit through tight areas. Read these instructions completelg and carefullg.

[] REMOVE THE BASKET

[] Open the freezer drawer until it stops. [] The freezer basket rests on a frame inside the

freezer drawer. Lift the basket up at the back.

[] Lift the front up and lift the entire basket up

and out ofthe drawee

REMOVE THE DRAWER FRONT (cont.)

[]

Lift up on both sides of the freezer drawer

handle to separate the drawer railings from the rail assemblies.

[]

Set the drawer front on a non-scratching surface,

[]

Push the rail assemblies back into locking

position.

[] REMOVE THE DRAWER FRONT

[] Remove the screw on each side of the railing.

Screw

Rail Assemblg Drawer

Assemblg

[] REMOVE THE BASE GRILLE

(if needed)

If, after removing the freezer drawer and refrigerator door, the refrigerator will still not fit through a doorwag, the base grille can be

removed.

[] Remove the base grille bg removing the

screws.

Installation Instructions

REPLACING THE FREEZER DRAWER (onsomemodels)

O wo people mag be required to complete

[] ATTACH AND SECURETHE DRAWER

[] Pull out the rail assemblies to the full length

[] Locate the slots on the inside of the rail

this procedure.

FRONT TO THE SLIDES

on each side of the cabinet.

assemblies near the back.

Slot

[] ATTACH AND SECURETHE DRAWER

FRONT TO THE SLIDES (cont.)

[] Replace the screws on both rail assemblies.

Screw

[] REPLACE THE FREEZER BASKET

Replace the lower freezer basket by lowering it into the frame.

Rail assembly

Insert the hooks at the back of the drawer

[]

railings into the slots on the rail assemblies.

[]

Lower the front of the drawer, making sure the

tabs on the sides of the railings fit into the front slots in the rail assemblies.

-Tab

Installation Instructions

REVERSINGTHE DOOR SWING (Single Door Refrigerator Models onlg)

IMPORTANT NOTES

When reversing the door swing: NOTE: Door swing is not reversible on stainless

steel models.

• Read the instructions all the way through before starting.

• Parts are included in the door hinge kit.

• Handle parts carefully to avoid scratching paint.

• Set screws down by their related parts to avoid using them in the wrong places.

• Provide a non-scratching work surface for the doors.

IMPORTANT: Once you begin, do not move the cabinet until door-swing reversal is completed.

These instructions are for changing the hinges from the right side to the left side-if you ever want to change the hinges back to the right side, follow

these same instructions and reverse all references to left and right.

• Once door swing is finalized, ensure the logo badge is properly aligned and permanently secured to the door by removing the adhesive cover on the back side. NOTE: A replacement logo badge is included in the hinge kit,

Unplug the refrigerator from its electrical outlet. Emptg all door shelves, including the dairg

compartment.

[] REMOVE THE

REFRIGERATOR DOOR

[] Tape the door shut with masking tape.

[] Remove the hinge cover on top of the

refrigerator door by carefullg prying it up with a putty knife, if necessary.

[] Using a 5/16" socket ratchet/driver, remove

the bolts securing the top hinge to the cabinet. Then lift the hinge straight up to free the hinge pin from the socket in the top of the door.

[] Carefully remove the door thimble from inside

the socket, This will be used again when reinstalling the door on the other side.

_ Hin2C°ver

I ? Top Hinge

TOOLS YOU WILL NEED

Adjustable Wrench 5/16" Socket

Masking Tape

Ratchet/Driver

Thin-blade Screwdriver

@ ©

Phillips Screwdriver

Torx T-20 Driver

[]

Remove the tape and tilt the door away from the cabinet. Lift the door off the center hinge pin. Ensure that the plastic hinge pin thimble remains on the hinge pin or inside door hinge pin hole located in the bottom of the door.

[] Set the door on a non-scratching surface with

the inside up.

Installation Instructions

[] REMOVE THE FREEZER DOOR

[] Tape the door shut with masking tape, [] Remove hinge pin from hinge bracket. This will

be used again with the new hinge bracket for the other side.

f_f_

[] Remove the tape and tilt the door awag from

the cabinet. Lift the door off the bottom hinge pin,

[] Remove the button plug from the left side of

the door. Remove the door thimble from the right side of the door. Install the door thimble

into the hole on the left and the button plug into the hole on the right.

[] TRANSFER CENTER HINGE

BRACKET (cont.I

[] Transfer the plug button and screw hole

cover in the hinge holes on the left side

to the right side.

[] Install the new center hinge bracket from the

kit on the left side.

[] Set the door on a non-scratching surface, with

the inside up.

[] TRANSFER CENTER HINGE BRACKET

[] Using a 5/16" socket ratchet/driver, remove the

bolts securing the center hinge to the cabinet.

[]

REMOVE BOTTOM HINGE AND LEVELING LEG

[]

Using a 1/2" socket ratchet/driver, remove the nut and hinge pin from the hinge bracket with leveling leg, Using a 5/16" socket ratchet/driver, remove the screws from the bottom hinge

bracket. These will be reinstalled on the

other side.

lq :e t .,age

[] Using a 5/16" socket ratchet/driver, remove

the screws from the leveling leg bracket on

the other side. These will be reinstalled on the

opposite side.

-"-'" Leveling Leg . _ Bracket

Installation Instructions

REVERSINGTHE DOORSWING (cont.)

[] INSTALL BOTTOM HINGE AND

LEVELING LEG

[] Using a 1/2" socket ratchet/driver, install the

hinge pin and nut in the opposite hole on the hinge bracket with leveling leg.

[] Using a 5/16" socket ratchet/driver, install the

hinge bracket with leveling leg on the left side of the refrigerator. The pin will be toward the

outside of the refrigerator.

[] Using a 5/16" socket ratchet/driver, install the

leveling leg bracket on the right side of the refrigerator.

TRANSFER REFRIGERATOR AND

FREEZER DOOR STOPS

[] Remove the door stop on the right side of the

bottom of the door by removing the two screws.

[] Hove the plastic hinge hole thimble to the

opposite hole.

[] Install the door stop on the left side, making

sure to line up the screw holes in the door stop

with the holes in the bottom of the door.

Bottom of Door (Right Side) Bottom of Door (Left Side)

ITI TRANSFER REFRIGERATOR

DOOR HANDLE TO RIGHT

Refer to Remove the Fresh Food Door Handle and Attach the Fresh Food Door Handle sections for instructions.

_'1 REHANG FREEZER DOOR

[] Lower the freezer door onto the bottom hinge pin.

Ensure that the plastic hinge pin thimble is on the hinge pin or inside the door hinge pin hole located

in the bottom of the door.

[]

Straighten the door and line it up with the center hinge bracket,

[]

Install the center hinge pin with a 3/4" socket ratchet/driver. Turn it until it extends through

the hinge bracket and into the freezer door

Installation Instructions

I'_ REHANG REFRIGERATOR DOOR

[] Lower the refrigerator door onto the center hinge

pin, Ensure that the plastic hinge pin thimble is on the center hinge pin or inside door hinge pin hole

located in the bottom of the doon

[] Insert the door thimble into the hinge hole

on top of the refrigerator door and then

insert the top hinge pin. Hake sure the door is aligned with the cabinet. Attach the hinge

to the top of the cabinet Iooselg with the bolts.

[] Make sure the gasket on the door is flush against

the cabinet and is not folded. Support the door on the handle side and make sure the door isstraight and the gap between the doors is even across the front. While holding the door in place, tighten the top hinge bolts. Replace the hinge cover.

REMOVING THE DOORS

(Double Door Refrigerator Models onlg)

IMPORTANT NOTES

NOTE: Door swing is not reversible.

• Read the instructions all the wag through before starting.

• Handle parts carefullg to avoid scratching paint.

• Set screws down bg their related parts to avoid using them in the wrong places.

• Provide a non-scratching work surface for the doors.

IMPORTANT: Once gou begin, do not move the cabinet.

These instructions are for removing the doors. Unplug the refrigerator from its electrical outlet, Emptg all door shelves, including the dairg

compartment,

TOOLS YOU WILL NEED

[] INSTALL THE LOGO BADGE

Remove the adhesive backing paper

and align the pins on the back of the badge with the holes in the door. Applg pressure to the badge to ensure it sticks to the door.

AdjustableWrench

MaskingTape

Phillips Screwdriver

3/8" and 10 mm Socket

Ratchet!Driver

Thin-blade Screwdriver

Installation Instructions

REMOVING THE DOORS (Double Door Refrigerator Models only)

[] REMOVE THE

REFRIGERATOR DOORS

[] Tape the doors shut with masking tape.

[] Start with left-hand door first: Remove

the screw securing the center hinge cover, lift the hinge cover and place to the side on top of the refrigerator.

Remove hinge cover (1 Phillips screw)

[] REMOVE THE REFRIGERATOR DOORS

(cont.)

[] Remove the tape and tilt the door awag from

the cabinet. Lift the door off the center hinge

pin, Ensure that the plastic hinge pin thimble remains on the hinge pin or inside door hinge pin hole located in the bottom of the door.

[] Set the door on a non-scratching surface with

the inside up.

[] Remove the hinge cover on top of the

refrigerator door bg removing the Phillips head screw and pulling the cover up.

[] Using a 5/16" socket ratchet/driver, remove

the bolts securing the top hinge to the cabinet. Then lift the hinge straight up to free the hinge pin from the socket in the top of the door.

i i

Hinge

Top Hing,

[] REMOVE CENTER HINGE

Using a 5/16" socket ratchet/driver, remove the bolts securing the center hinge to the cabinet. Set the hinge and bolts aside.

[] REMOVE OPPOSITE DOOR

Follow the same procedure on the opposite door. There are no center hinge covers on the opposite side.

[] REMOVE FREEZER DRAWER

Refer to the Removing the Freezer Drawer section for instructions.

Installation Instructions

REPLACI NG THE DO0 RS(Double Door Refrigerator Models onlg)

[] INSTALL CENTER HINGE

Install the center hinge on each side.

[] REHANG REFRIGERATOR DOORS

[] Lower the refrigerator door onto the center

hinge pin. Ensure that the plastic hinge pin

thimble is on the center hinge pin or inside

door hinge pin hole located in the bottom of the door.

[] Securely tope the door shut with masking tope

or hove o second person support the door.

[] Insert the top hinge pin into the hinge hole on

top of the refrigerator door. Hake sure the door

is aligned with the cabinet and opposite doon

Attach the hinge to the top of the cabinet

Iooselg with the bolts.

[] Hake sure the gasket on the door is flush

against the cabinet and is not folded. Hake sure the door is straight and the gap between

the doors is even across the front. While

holding the aligned door in place, tighten

the top hinge bolts. Replace the hinge cover

and screw.

[] REPLACE OPPOSITE DOOR

Follow the same procedure on the opposite door. There is no water line or hinge coven

[] ALIGN DOUBLE DOORS

If the top of the doors are uneven, first try to raise the lowest door bg turning the leveling leg

on the same side as the door until the doors ore even. If the unit rocks, re-adJust the leveling

legs to the extent that the unit is stable.

€

If the doors remain uneven, turn the adjustable pin to raise, or lower, the left door to match the right door. Use u 1/4" Allen wrench to turn the pin.

__ble pin

[] REPLACE FREEZER DRAWER

Refer to the Replacing the Freezer Drawer section for instructions.

Hinge Cover -_---_ \_ __ .

Top H,nge Bolts___

(appearancemay vary)

Installation Instructions

INSTALLING THE WATER LINE (ICEMAKER MODELS)

BEFORE YOU BEGIN

Recommended copper water supply kits are

WX8X2, WX8X3 or WX8X4, depending on the

amount of tubing you need. Approved plastic

water supply lines are GE SmartConnect T'

Refrigerator Tubing (WX08X10006, WX08X10015 and WX08X10025).

When connecting your refrigerator to a GE Reverse

Osmosis Water System, the only approved installation is with a GE RVKit. For other reverse

osmosis water systems, follow the manufacturer's recommendations.

If the water supply to the refrigerator is from a Reverse Osmosis Water Filtration System

AND the refrigerator also has a water filter,

use the refrigerator's filter bypass plug. Using

the refrigerator's water filtration cartridge in

conjunction with the ROfilter can result in hollow ice cubes.

This water line installation is not warranted by the refrigerator or icemaker manufacturer. Follow these instructions carefully to minimize the risk of

expensive water damage.

Water hammer (water banging in the pipes) in

house plumbing can cause damage to refrigerator parts and lead to water leakage or flooding. Call a qualified plumber to correct water hammer before installing the water supply line to the refrigerator.

To prevent burns and product damage, do not hook

up the water line to the hot water line. If you use your refrigerator before connecting

the water line, make sure the icemaker power

switch is in the O loft} position. Do not install the icemaker tubing in areas where

temperatures fall below freezing. When using any electrical device (such as a power

drill) during installation, be sure the device is double insulated or grounded in a manner to prevent the hazard of electric shock, or is battery powered.

All installations must be in accordance with local

plumbing code requirements.

WHAT YOU WILL NEED

• Copper or GE SmartConnect" Refrigerator Tubing kit, 1/4" outer diameter to connect the

refrigerator to the water supply. If using copper, be sure both ends of the tubing are cut square.

To determine how much tubing you need: measure the distance from the water valve on the back

of the refrigerator to the water supply pipe.

Be sure there is sufficient extra tubing to allow

the refrigerator to move out from the wall after installation.

GE SmartConnect T'Refrigerator Tubing Kits are available in the following lengths:

6' (1.8 m) - WX08X10006

15' (4.6 m) - WXO8XIO015

25' (7.6 m) -WX08X10025

Installation Instructions

WHAT YOU WILL NEED (CONT.)

NOTE: The onlg GE approved plastic tubing

is that supplied in GE SmartConnect"

Refrigerator Tubing kits. Do not use ang other plastic water supplg line because the line is under pressure at all times. Certain tgpes of plastic will crack or rupture with age and cause

water damage to gour home.

• A GE water supplg kit (containing tubing, shutoff valve and fittings listed below) is available at extra cost from your dealer or from Parts and

Accessories, 800.626.2002 (in Canada

1.888.261.3055).

• A cold water supplg. The water pressure must be between 20 and 120 p.s.i. (1.4-8.1 bar).

Install the shutoff valve on the nearest frequentlg

used drinking water line.

SHUT OFF THE MAIN WATER SUPPLY

Turn on the nearest faucet long enough to clear the line of water.

[] CHOOSE THE VALVE LOCATION

Choose a location for the valve that is easilg accessible, It is best to connect into the side

of a vertical water pipe. When it is necessary to connect into a horizontal water pipe, make the connection to the top or side, rather than at the bottom, to avoid drawing off any sediment from the water pipe.

• Power drill.

• 1/2" or adjustable wrench.

° Straight and Phillips blade screwdriver.

° Two 1/4" outer diameter compression nuts

and 2 ferrules (sleeves)--to connect the copper tubing to the shutoff valve and the refrigerator

water valve.

° If you are using a GE SmartConnect T"

Refrigerator Tubing kit, the necessary fittings are preassembled to the tubing.

• If your existing copper water line has a flared

fitting at the end, you will need an adapter

(available at plumbing supply stores) to connect

the water line to the refrigerator OR you can cut

off the flared fitting with a tube cutter and then use a compression fitting. Do not cut formed end

from GE SmartConnecf" Refrigerator tubing.

[] DRILL THE HOLE FOR THE VALVE

Drill a 1/4" hole in the water pipe (even if using a self-piercing valve), using a sharp bit. Remove any burrs resulting from drilling the hole in the pipe.

Take care not to allow water to drain into the drill.

Failure to drill a 1/4" hole may result in reduced ice production or smaller cubes.

° Shutoff valve to connect to the cold water line.

The shutoff valve should have a water inlet with

a minimum inside diameter of 5/32" at the point of connection to the COLD WATER LINE. Saddle-

type shutoff valves are included in many water

supplg kits. Before purchasing, make sure a saddle-type valve complies with your local plumbing codes.

Installation Instructions

INSTALLING THE WATER LINE (CONT.)

[] FASTEN THE SHUTOFF VALVE

Fasten the shutoff valve to the cold water pipe

with the pipe clamp.

Pipe Clamp_4_

Saddle-Type Shutoff Valve

NOTE: Commonwealth of Massachusetts

Plumbing Codes 248CHR shall be adhered to, Saddle valves are illegal and use is not permitted in Hassachusetts. Consult with your licensed plumber.

[] TIGHTEN THE PIPE CLAMP

Tighten the clamp screws until the sealing washer begins to swell.

NOTE: Do not overtighten or you may crush

the tubing.

Washer

Pipe

Clamp

Inlet End

Water Pipe

[] CONNECT THE TUBING TO THE VALVE

Place the compression nut and ferrule (sleeve)

for copper tubing onto the end of the tubing and connect it to the shutoff valve.

Hake sure the tubing is fully inserted into

the valve. Tighten the compression nut securely.

For plastic tubing from a GE SmartConnect T"

Refrigerator Tubing kit, insert the molded end of the tubing into the shutoff valve and tighten compression nut until it is hand tight, then tighten one additional turn with a wrench. Overtightening may cause leaks.

Shutoff Valve Compression Nut

Saddle-Type I

SmartConnectT"

Tubing

Packing Nut

Outlet Valve Ferrule (sleeve)

NOTE: Commonwealth of Massachusetts

Plumbing Codes 248CHR shall be adhered to, Saddle valves are illegal and use is not permitted

in Hassachusetts. Consult with your licensed

plumber.

[] ROUTE THE TUBING

Route the tubing between the cold water line and the refrigerator.

Route the tubing through a hole drilled in the wall or floor (behind the refrigerator or adjacent base cabinet) as close to the wall as possible.

[] FLUSH OUT THE TUBING

Turn the main water supply on and flush out the tubing until the water is clear.

Shut the water off at the water valve after about one quart (1 liter) of water has been

flushed through the tubing.

go back to Step 1 in Installing the Refrigerator.

I To complete the installation of the refrigerator,

+ 90 hidden pages